Related
Hi everyone
yesterday I bought a X10 (it wasn't brand new)
I turned it on and it asked me for settings (language, time, etc) (yeah it's not new but they changed the rom before sell it to me)
I worked with it for like 10-15min and I got a big vibrate and it turned off. I pluged it into the charger, there was an orange led for 5min and then nothing, when I tried to turn the phone on I saw SE logo and it restarted. I plugged it to the charger, nothing again, not even orange led
I took it to a store and they shocked the battery, i came back, turned it on, it booted ok everything was fine,I plugged it again to full charge. orange led for 1.5h and then green led.I worked with it a short time then turned it off to put the sim and sd card in
when I turned it on it booted till lock screen and rebooted. again SE logo then boot again
it sometimes boot till lock screen sometimes only se logo and reboot
when it goes to lock screen I see antena has red x on it, i thought maybe that's the problem, i removed sim and sd, still the same
Please please please help me
ps 1: I can't connect it to the pc, I tried but when pc wants to recognize it and install drivers, it stops and says "not successful"
Have a look in the dev section for flashtool (there's a tutorial in the q&a section), look in the firmwares sticky in the dev section and download the firmware for your region. I suggest you pick a generic firmware. Now use flashtool to flash the firmware to the phone.
This should solve the problem.
thank you Frosty for fast answer
but my problem is my pc dosen't recognize the phone
flashtool works even without drivers?
Flashtool works in flash mode. If you can't get your computer to recognise the phone when it is powered on, it should still recognise it in flash mode. If not, there is an option in flashtool to install the drivers.
Sent from my x10, rocking Wolf's 2.3.3 + DooMKernel, overclocked to 1.2 GHz...
good, so I think I still have a chance to fix it
btw, now I have stock 2.3.3 installed
which rom do you recommend? should I install 2.3.3 again or downgrade to 2.1?
I want it to support farsi
X10i_3.0.1.G.0.75_CUSTOMIZEDARO-ARO GENERIC 1241-1846
is right?
You could do 2.3.3 or 2.1. It shouldn't matter.
As for Farsi support, 2.1 supports more languages than 2.3.3 I think. I just checked the list of available languages on my 2.3.3 ROM and Farsi isn't listed. 2.1 might support it.
You could always try both to see which one better suits your needs.
That firmware you have is 2.3.3, by the way.
thank you so much frosty
I asked if i could install 2.3.3 because now have 2.3.3 and i have this problem. installing same version will fix it?
and one question about baseband
should i download one or it comes in firmware pack/zip
if I have to download it, how do I know which one?
Your're welcome.
Oh, in that case, you should be fine.
The baseband is included in the firmware file.
I'm facing a weird problem
I can't turn my phone on, I've been told to try flashtool and install a new rom
my old rom was 2.3.3
I downloaded flashtool and X10i_3.0.1.G.0.75_CUSTOMIZEDARO-ARO GENERIC 1241-1846
first time I tried instrudoction in second post in this topic. it seems flashtool recognized my device and startet flashing but after a few min it said flash aborted
I wanted to try again but this time even before i connect the device to usb cable, flashtool say flashing start and nothing happen
I also tried SE update service, it downloaded the rom and it seem it worked (second green bar went to the end and said disconnect phone and restart)
I restart the phone but it reset after SE logo, sometime it boot till lock screen and reset again
Please help me
Sorry to say this, but you might be out of luck.
If re-flashing stock couldn't fix it, your issue may be a hardware problem.
Do you have any sort of warranty? If it's second hand, you probably don't.
You could try taking it to a Sony Ericsson service center and see if they can do anything.
omg
I'm officially beeeeeep
thanks anyway Frosty
btw, pc campanion and se update service do something different
is it possible that pc companion can fix it?
Well you could try. Couldn't hurt.
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
If the battery has drained out, it might take some time before it kicks in and indicates that it is charging.
If the ROM has failed somehow, it might not show that it is charging at all, but might be charging.
Either way: Let it charge "blindly" for a while, and see what happens.
Once it does boot up to some level or shows life-signs, let it charge fully before you'l attempt a ROM flash.
The flash/recovery mode needs a full battery, and reason is that the external power isn't used even when connected while in flash/recovery mode.
If you happen to be in bad luck, and the ROM failed as a result of a drained battery, you might have to charge the battery externally. Use an external battery charger made for 3.6 volts Lithium Polymer batteries, and make sure to align the + and - terminals properly.
I can recommend the multicharger from Powerbase, called C-734U:
http://www.powerbasehk.com/product.php?id=148
Using it myself to charge the X10 battery, as well as other batteries from other devices I have.
EDIT:
(For some reason, powerbase has taken back that it'll charge Lipo batteries, but when I bought mine, it was described as a li-ion, li-poly and Ni-MH charger, and it't ability to charge li-poly batteries was the very one reason to why I bought it.
I suspect PowerBase does not want to take responsibility if anything happens to the li-poly-batteries, as they are known to be more dangerous than other types.)
I've left it on the wall charger all night, no response or anything. Luckily, I bought a new battery a few days ago, so when that comes in, hopefully it will be charged enough for this thing to boot.
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
laneyofdeath said:
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
Click to expand...
Click to collapse
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
king-iyokan said:
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Yeah, i'm not sure what he expected. But, good news! Now for some reason my phone started blinking red whenever I tried to turn it on! I guess the battery completely ran out or something. It also blinks every now and then when plugged in, so I guess it's charging. The previous owner of this phone said that it had some battery problems, so that's why I ordered that new battery. I'll let it charge for awhile and let you guys know what happens.
Okay, after getting my new battery, the phone will still not turn on. I think i've figured out two behaviors:
1. If the battery is nearly completely out of charge, it will flash a red light
2. If the battery has charge, it will not do anything at all.
Anyone know how to fix this?
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
ToledoJab said:
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
Click to expand...
Click to collapse
No vibration, the red LED flashes three times, and that is , as I said before, what happens when the battery seems to not have any charge. If I have a charged battery it does absolutely nothing.
Have you removed sim & sd card and tried. I know it sounds dumb but when I flashed a bad kernel I had to try to connect flash mode like 10 times. Finally I left the phone unplugged from pc, started flashtool and started flashing. I only put battery in phone just before holding back key. I never connected USB until tool said to dis-connect phone and connect in flashmode.
i wish you luck, I know how I felt when it went wrong
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
FireFreek said:
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
Click to expand...
Click to collapse
Try to flash any latest kernel via flashtool . Go for doomkernel . I think its software issue . Try this first .
Almost same here please help..
Last night battery ran out of charge & phone switched off.. then i plugged the charger it doesn't charge.. after some time i tried turning on.. Vibrates with the green LED but nothing happens then..
Note: This is not the 1st time i'm letting my phone drain, but facing this problem for the 1st time..
Rom : Spikelabs GB Gaming rom
Kernel : Ferakernel v23 beta6
I tried another battery, charger, data cable.. Tried flashing stock & spikelabs kernel., but of no use..
Any help is greatly appreciated..
Thanks in advance.. :good:
Something like that happened to me not long ago!
I was trying to flash some ROMs and I messed up then my phone wouldn't turn on!
But Miracously, I could flash a Stock 2.3.3 which fixed the problem!
At first, I used Sony PC Companion, which helped a lot- and after I screwed it for the second time, I used FlashTool-
I don't know if this was helpful, but I hope your x10 will be fixed soon!
yeah try the PC Companion first, it helped me too a couple of weeks ago
No luck...
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
ashok weird said:
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
Click to expand...
Click to collapse
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
sanababitz said:
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
Click to expand...
Click to collapse
Tried Ferakernel, Stock GB kernel, etc bro.. No luck..
Flashed Stock GB firmware more than 3 times still no luck :crying:
SEUS not working _ couldn't connect to network..
SUS does not have x10 enlisted
Went to 3 service shops at - Ritchie street, Chennai. They simply said harware issue (Short in board) and gave back the phone.
Now given at a better service centre. Will get back on monday it seems. Will update the status friends..
Thanks..
Here also they said the same reason friends.. Short in board..
Is there any way i could recover the phone???
Hey guys i've a problem with my x10
So one night i was playing with it than the other day the phone would start
so i thought yeah right might be the battery or something. i took it to my friends x10 it was with 87% charged so i exclude this
Than i tried to flash with flashtool a new kernel and i get stuck at 9% or 15% depending on the kernel i use.
With SEUS it starts to repair but it says. No new updates avaiable after a few moments.
Some information regarding my phone
Unlocked Bootloader
FXP KERNEL
MM TEAM MIUI V4
The phone vibrate but doesn't start or load the kernel.
What do i do?!
Srry for my bad english
Thx in advance
Usrle flashtool to reflash kernel or firmware.
already did but i get stuck at 9% or 15% flashing the kernel
I'm downloading a full generic rom x10a
having similar problem
Hi, I had similar problem as well
X10i running FXP CM7 suddenly just wont boot n charge after I turn off the phone
it wont boot after flashing anything (firm or kernel) except the official firm
now that I end up with a cap R bootloader but flashtool claim that bootloader is rooted
do I still keep the bootloader unlock?
i guess you have a locked bootloader since the original firmware is loading just fine even tho rooting has nothing to do with the bootloader it self. i'm only guessing.
I'm stuck at. Flashing Loader
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
[XBOCT]™ said:
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
Click to expand...
Click to collapse
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
same problem repeat
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
mooving said:
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
Click to expand...
Click to collapse
i'm using
X10a_2.1update1_r2.1.A.0.435_Generic.ftf
And it get stuck at Flashing loader
Idk but i can "read" the kernel when i dump the propriets but i can't "right" when i try to flash something
Anyone?
guys?
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
LJE said:
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
Click to expand...
Click to collapse
maybe i'm wrong idk maybe is a soft brick. thats why i'm asking for some help.
almomdegal said:
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
Click to expand...
Click to collapse
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Try wotanserver's flashtool...
http://www.wotanserver.com/en/
Good luck
SysGhost said:
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Click to expand...
Click to collapse
Didn't work, i even use my friends battery to flash it and it didn't work
almomdegal said:
Didn't work, i even use my friends battery to flash it and it didn't work
Click to expand...
Click to collapse
Well, if the battery issue was fixed, and you're sure the battery is fully charged, then try this: (Quoting from my other post)
I've charged/replaced the battery, and are having trouble with starting up. Earlier flash failed. Now what?
Don't worry. It's pretty darn hard to truly brick this device. Even if the screen remains black, there's still hope.
Once that the battery issue has been dealt with, you can move on:
Download the latest Flashtool and the proper global firmware (FTF-file) for your device from here:
http://forum.xda-developers.com/show...ight=flashtool
1: Extract/Install the Flashtool to a folder of your liking.
2: Copy the ftf-file to the "firmware" folder in the Flashtool folder you just created above.
3: Start Flashtool. Click the Bolt icon (flash). A Window appear. There, choose "flashmode". Cllick OK.
4: A new window appears. In the list on the left, choose the Generic firmware you downloaded and copied into the "firmware" folder. Should have a similar name as the file itself. (Or manually open the ftf-file from the "..." icon on the top right.)
5: Hit "OK. Follow the instructions you get on the screen:
1 - Unplug the device.
2 - Power off the device. (Unplug and replug the battery to be sure it really off, and not stuck in black screen)
3 - Press the "back" putton, and hold it down while performing the next task.
4 - Plug the device into the computers USB.
Click to expand...
Click to collapse
Forced flashing should now start.
Click to expand...
Click to collapse
time to accept the fact that it is really brick
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
mooving said:
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
Click to expand...
Click to collapse
yeah i guess so.
I just needed this closure i'll send it to service today
Hi there. First of all, sorry about my english, but i'm spanish
I was reading a lot, and i cant find a solution to my phone. It sudently becomes a brick just when charging (with anothers phone charger) and the battery was lower than 10%
It doesn't work, and don't response to any of all solutions i've read (Take out SIM, SD card, remove battery and wait... ) no way... Screen never come back to iluminate again. Just, when pushing power buttom, the phone's vibrates.
So tired of the brick, i've arrived at this page. And I read this post:
http://forum.xda-developers.com/showthread.php?t=1568792
And try to become my phone back...
At least, the phone enter in flashmode, and i can flash with flashtools... but the phone never come back... just the brick
I tryed to flash with the Xperia_2011_FreeXperia_ALL.ftf file and OK
Afther that, take out the USB and flash again with one ROM i get from here:
Xperia Mini Pro (SK17i)
4.0.2.A.0.42 - http://www.mediafire.com/?hevz3x5w9pqt24q
4.1.B.0.431 - http://www.mediafire.com/?j0bdx06zz5skvzt
But the phone never works. One time afther flashing with 4.0.2.A.0.42 i noticed, that trying to power on the phone, the red led shyne 3 times, and thats supposed to be the battery. But i don't know if the battery now is charged. I've left it hours charging, and hours too to the USB...
Supposedly, i cant flash without battery in the phone, but flashtools finish correctly
So... any idea?
There is something i can do?
Thank all of you who read this!
Its probably battery empty. recharge battery or get a friends and try
Sent from my X8 using Tapatalk 2
First make sure that your battery is really fine. Try another one.
If that fails, see if you can get your device into flash mode?(Switched off+Vol Down + USB cable)
If yes, try flashing a custom ROM. For example, download CyanogenMod from here, use Flashtool (guide) to flash the kernel provided in the downloaded ROM's ZIP file. Then, boot again into Clockword Mod Recovery(Keep pressing Vol DOwn button while boot or google for how to enter recovery for your phone). Copy the downloaded Cyanogenmod ZIP to SD card and install it via ClockwordMod recovery.
See if the above works.
bandarigoda123 said:
Its probably battery empty. recharge battery or get a friends and try
Sent from my X8 using Tapatalk 2
Click to expand...
Click to collapse
But, if it was problem of battery, i suppose, that i can't finish flashing with flashtoolts. Not?
Milven said:
But, if it was problem of battery, i suppose, that i can't finish flashing with flashtoolts. Not?
Click to expand...
Click to collapse
Try booting up your phone with the USB connector plugged in the PC (maybe it will charge the battery then)
Milven said:
But, if it was problem of battery, i suppose, that i can't finish flashing with flashtoolts. Not?
Click to expand...
Click to collapse
At least my phone (LWW WT19i does not work without the battery with Flashtool. I'm not sure about your device.
Anyway try flashing a custom ROM like I said. Try unlocking bootloader first though from here
U said that red light show when try to on the phone.
Just try another battery.. It should work
Sent from my X8 using Tapatalk 2
You said LED blinks 3 times so if the color of LED is RED then it indicates empty battery..
Hey, my problem wasnt the same as yours, but it helped for me when i got only service logo on screen.
On this link you find a "Play_v1.01_TA brick fix UPDATE" zip.
Download, unpack and flash it.
http://forum.xda-developers.com/showthread.php?t=1126358&page=10
I hope it will help u.
Milven said:
Hi there. First of all, sorry about my english, but i'm spanish
I was reading a lot, and i cant find a solution to my phone. It sudently becomes a brick just when charging (with anothers phone charger) and the battery was lower than 10%
It doesn't work, and don't response to any of all solutions i've read (Take out SIM, SD card, remove battery and wait... ) no way... Screen never come back to iluminate again. Just, when pushing power buttom, the phone's vibrates.
So tired of the brick, i've arrived at this page. And I read this post:
http://forum.xda-developers.com/showthread.php?t=1568792
And try to become my phone back...
At least, the phone enter in flashmode, and i can flash with flashtools... but the phone never come back... just the brick
I tryed to flash with the Xperia_2011_FreeXperia_ALL.ftf file and OK
Afther that, take out the USB and flash again with one ROM i get from here:
Xperia Mini Pro (SK17i)
4.0.2.A.0.42 - http://www.mediafire.com/?hevz3x5w9pqt24q
4.1.B.0.431 - http://www.mediafire.com/?j0bdx06zz5skvzt
But the phone never works. One time afther flashing with 4.0.2.A.0.42 i noticed, that trying to power on the phone, the red led shyne 3 times, and thats supposed to be the battery. But i don't know if the battery now is charged. I've left it hours charging, and hours too to the USB...
Supposedly, i cant flash without battery in the phone, but flashtools finish correctly
So... any idea?
There is something i can do?
Thank all of you who read this!
Click to expand...
Click to collapse
Hi Milven,
I got the same problem with you yesterday. Few hours sitting in front of my PC and hopeless.
I tried everything same as yours, finally I found and solve the case.
Install this http://www.sonymobile.com/global-en/tools/update-service/
And let it update your phone.
Done. It's back to brand new.
Hope you read this.
frdnoer said:
Hi Milven,
I got the same problem with you yesterday. Few hours sitting in front of my PC and hopeless.
I tried everything same as yours, finally I found and solve the case.
Install this http://www.sonymobile.com/global-en/tools/update-service/
And let it update your phone.
Done. It's back to brand new.
Hope you read this.
Click to expand...
Click to collapse
That's true. Try fixing it by using sony repairment. I did it and it worked for my phone. I hope it does for you
Sent from my Xperia, Asri Aisyah El Zahra
i've the same problem as you. charge your battery with desktop charger. not too long, i put the battery and flash firmware in flashtool. and it work. when the flashing done and the device on, my battery just 3% lol. flashing with flashtool only takes a few minutes
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
gonix said:
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Click to expand...
Click to collapse
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Screen-shots are from the old PC Companion, byt they still looks very much like them in the new version
http://forum.xda-developers.com/showpost.php?p=17458289&postcount=8
Emperor.dk said:
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
Click to expand...
Click to collapse
Oh I know someone who has the same x10 with me. I guess Ill have to try your suggestion.
SmG67 said:
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Click to expand...
Click to collapse
It doesnt help because when Im in the part where it says, press the back button while inserting the usb, the phone cannot be detected and so the update cannot continue.