Vibrant Unusual Problems - Vibrant Q&A, Help & Troubleshooting

Hello guys
I am having various problem with Samsung Vibrant currently running stock froyo 2.2
Problems
1. It does not start using the power button. It only starts automatically when I plug in the wall charger or usb cable connected to PC/Laptop.
Before: It used to start using the power button but when i tried to go into recovery mode using the keys combo this problem occured.
2. Whenever I switch off (power off) the phone it restarts automatically. (when connected to wall charger or usb cable connected to PC/Laptop)
Before: It restarts everytime i swtich off even when its not connected to wall charger or usb cable connected to PC/Laptop.
3. When I connect it to PC/Laptop it always shows "USB NOT RECOGNIZED". I tried many diff drivers, diff pcs/laptops, 2 diff cables, diff connection modes in mobile.
It doesnt charge from one cable, so i thought the cable has gone bad and brought a new one. it charges from new one but does not connect and same problem happens.
4. I tried to root the phone using galaxysrooter becoz i cannot it to pc. GalaxySrooter installed succesfully but when i run it, it shows some error (somthing like "XXX you sdcard XXX ?" dont remember the error sorry).
Then I went to recovery mode to root but there is showed the Signing verification error becoz of 3e.
5. Whenever i disconnect it from wall charger or usb cable connected to PC/Laptop the battery charging icon still remains and still shows that it is charging.
6. Its locked on t-mobile (not an issue)
I searched many websites but cannot find a solution.
Can anyone please help me fix these issues ?
Can anyone please tell me how can I root this phone and install custom rom without connecting to PC. I cannot use superoneclick root but no pc connection, cannot root from recovery mode becoz of the Verification signing issue (3e).
please help

in this same forum section of Questions and Answers go to the top and it will say noob guide read through it atleast 5 or 6 times. once u understand. you can go to development section and download "toolbox" it should be a sticky actually so right on top and will say noob next to it. by the way i hope ur not offended by me using noob often to refer to guides but all honestly it will help you step by step understand and explain what u need to do to custom flash. please be patient. read carefully over and over. every step must be followed precisely. good luck. im a noob too but im learning very very slowly.

I already read that sticky, but i cannot find the answer .. because my phone is expereincing some problems and also my phone is not rooted.
Can I install (flash) stock 2.1 without connecting to PC and without rooting ? if yes then how ?

Ok bro here is what I think u should n definitely try this I believe that it will definitely give u a break through.
1) go to vibrant development forum n download tool box install it open connect ur phone and click on first option install drivers. That will solve automatically the driver issue.
If it doesn't work u should try to upgrade the ddrivers n stuff for ur pc/laptop as well. Give it a try n let me know how it goes. N check to see if u need to mount the usb or not and also to have usb debugging on or not the software tells u.
Sent from my SGH-T959 using XDA App

i have an anointing problem with my vibrant, i installed a rom for vibrant based on the captivate rom from the at&t, and i went back to a regular 2.2.1 vibrant rom, but now i get the at&t world phone logo every time i reboot my phone, i have try everything from odin it back to stock but still get the at&t logo, can anyone here help me please?

Related

[Q] heellppp:(

ODIN or my laptop wont recognize my vibrantttt...i already downloaded the rite drivers... and KIES and KIES mini ... i tried evryting switching USB ports opening and closing ODIN rebooting my phone clearing cache and data and nothing... and i no its noy hardware lockd kuz i kan easily go to recovery and download mode... i even tried it in a diffrent PC and nothing... it chages and evryting .. the only problem is .. wen i turn it on.. it stays in the smasung vibrant boot up screen..... n no i cant put debbugin USB because it wont load up the phone... any helppp plzzz
how exactly are you doing it? kindly post your procedures you might doing something wrong.
kush815 said:
i already downloaded the rite drivers...
Click to expand...
Click to collapse
Are you SURE that you download the RIGHT drivers?
lol
try this:
Open Odin (As admin, if on vista/win7)
Get your phone into DL mode.
Plug it in, watch for a COM port. If none show up within the minute unplug & replug (And DON'T close Odin this time)
iynfynity said:
how exactly are you doing it? kindly post your procedures you might doing something wrong.
Click to expand...
Click to collapse
Yeah, I'm with master... you sure you got the right drivers??
check out my thread here.. I had troubles with odin at first and as I figured out what i was doing wrong I updated the post. It pretty much walks you through what to do and directs you to different threads that deal with odin, the files needed, and what to do to make it all work.
If usb debugging was not enabled and you can't boot up the phone, you are screwed. I had the same thing happen to me. Sorry.
You shouldn't need USB Debugging if you are getting into download mode... I had the OTA JI6 update freeze my phone at the Vibrant screen. I was stock, unrooted, no debugging, and my phone is less than 2 months old.
I was able to get into Download mode by pulling battery (since power off didn't work), put battery back in, hold down volume up + volume down buttons, plug USB into computer, plug USB into phone and download mode came right up...
I then unplugged the USB from the computer and opened ODIN.
Plugged the USB back into the computer and ODIN recognized it... ran the JI6 ODIN update and it soft bricked with the computer ! phone logo... simply ran through the same procedure to get back into download mode and re-flashed with ODIN and it worked fine after that!! No data loss or anything!!
You just have to keep trying... you may think you've tried everything, but try it all again because doing it a second time, you may get lucky and it works.
Good luck!!

new to the vibrant, maybe i bricked it

i picked it up used with stock rom, no mods. i rooted, then installed nero v3 with voodoo and then v5 with voodoo.... then i tried a custom battery mod and it screwed my phone up... cant get past the vibrant start screen, cant read the ext sd and the phone drivers will not work... computer detects it, but no drivers are installed. i have used the 32 bit driver 64 bit drivers, kies, kies mini, odin v1 and v1.7, still nothing... i can get into cwm recovery, but only with voodoo enabled, and can get into download mode, but i cant seem to get the computer to read it. have used 4 different computer, win 7 and 32 bit xp....also have tried drivers with pdanet and easy tether, but still no luck... can you offer any help to me??? thanks in advance.
as of u have done so much and nothing helped i would cry , and for not readin on how to unbrick your phone right on top of the forum you should cry too .
and if look good enough every 3rd thread that is made is how to unbrick the phone
@bartek
OK...OMG dude... you had like 5 posts 3 days ago...how are you helping this individual out other then giving him all your illegible ramblings that you are posting and ridiculing individuals as you go .. I'm sry, I don't mean to rant but damn...
Anyway OP, your just soft bricked. If you can get into d/l mode then I would either go ahead and ODIN back or if you can get into CWM recovery and you still have Nero 5 in your root, I would just reflash it and it should take care of it...enable voodoo when you flash Nero 5 ..you should be ok.
First off, I have been searching the forums for almost two weeks now and cannot find a solution....I have tried everything......the first problem is that no matter what drivers I use, the computer still says usb device not recognized, so I cannot get odin or heimdall to communicate, neither kies or kies mini.....
Well, now I turned it on this morning and I cannot get into cwm or dload mode.....just keeps bootlooping and linda talks and says riskful operation, then reboots......I am lost, don't know what else to do, I'm gonna throw this phone out the window
Sent from my HTC Vision using XDA App
bouzouki said:
First off, I have been searching the forums for almost two weeks now and cannot find a solution....I have tried everything......the first problem is that no matter what drivers I use, the computer still says usb device not recognized, so I cannot get odin or heimdall to communicate, neither kies or kies mini.....
Well, now I turned it on this morning and I cannot get into cwm or dload mode.....just keeps bootlooping and linda talks and says riskful operation, then reboots......I am lost, don't know what else to do, I'm gonna throw this phone out the window
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
I would say Odin is your friend. go back to stock and start over Here is a start
http://www.youtube.com/watch?v=KyAIUOYufrU
Part 2: http://www.youtube.com/watch?v=33I-aNCypVM
hope this helps you
no dont throw the phoine out give it to mee ! or u can just remove your battery while phone is hooked up to computer with usb push volume up and volume down hold it put battery in , yellow android showed up ? u good to odin if he didnt redo repeat those steps until u will see him
how can i get odin to communicate when the computer wont read it?? it says usb device not recognized and no matter which drivers i install, it wont communicate.... and plus odin wont connect, i have tried multiple times.....heimdall drivers wont install either, it gives me a failed result.... i have used the 32 bit drivers, 64 bit drivers, kies, kies mini for vibrant, odin, heimdall, everything.... i have a g2 and have done so much to it with no problems, this phone has got me confused...
u need damn download mode for odin to see your phone damn could you just do those steps that i told you ? and btw open up odin so u can see when u phone is detected it will light up i nyellow
onc3 again
1. phone connected to computer
2.odin open
3.take out battery (out of your phone)
4.hold volume up volume down (allthe time)
5.put battery back in
6. put files in odin flash back
bouzouki said:
how can i get odin to communicate when the computer wont read it?? it says usb device not recognized and no matter which drivers i install, it wont communicate.... and plus odin wont connect, i have tried multiple times.....heimdall drivers wont install either, it gives me a failed result.... i have used the 32 bit drivers, 64 bit drivers, kies, kies mini for vibrant, odin, heimdall, everything.... i have a g2 and have done so much to it with no problems, this phone has got me confused...
Click to expand...
Click to collapse
I gotcha.... not to sound like an idiot but have you tried a different usb port? If your using one on the front, try ones in the back if your on a desktop.. if that doesnt work try running ODIN in XP SP3 compatibility mode
bartek25 said:
u need damn download mode for odin to see your phone damn could you just do those steps that i told you ? and btw open up odin so u can see when u phone is detected it will light up i nyellow
Click to expand...
Click to collapse
I think he's saying that odin doesn't detect his phone and therefore doesn't light up yellow. Happened to me too. I'm on the epic. I tried everything. But odin finally found my device. Try different usb ports, a different wire, reboot both phone and pc. Switch between usb debugging on and off. Try it with sideloading enabled and not. I eventually found a combimation that worked. These phones are fickle. It'll work eventually.
Sent from my SPH-D700 using XDA App
+1 on what he said above try connectin and disconection your phone lots of times 2 forgot it happend to me too once .sorry it was a while ago
i have used front usb ports, and the back ones, have even used 3 different computers. but same result. will odin connect even if the driver are not installed correctly and the computer doesnt recognize the usb device? and also, now i have the problem where i cannot get the phone into dload mode, it keep bootlooping to the samsung vibrant start screen and linda says riskful operation.
bouzouki said:
i have used front usb ports, and the back ones, have even used 3 different computers. but same result. will odin connect even if the driver are not installed correctly and the computer doesnt recognize the usb device? and also, now i have the problem where i cannot get the phone into dload mode, it keep bootlooping to the samsung vibrant start screen and linda says riskful operation.
Click to expand...
Click to collapse
As far as I know, ODIN wont recognize your phone without being in download mode and drivers installed on your computer.
bouzouki said:
i have used front usb ports, and the back ones, have even used 3 different computers. but same result. will odin connect even if the driver are not installed correctly and the computer doesnt recognize the usb device? and also, now i have the problem where i cannot get the phone into dload mode, it keep bootlooping to the samsung vibrant start screen and linda says riskful operation.
Click to expand...
Click to collapse
No I believe you need the correct drivers installed. At this point either your missing something or don't have the correct driver to install. Maybe someone can point out where all the proper drives are for you to download
speachless ....if u wont follow what i wrote im helpless.goodbye. and why u turning your phone on dude download mode is battery out phone connected to ANY usb port hold vol up vol down hold all time and puit battery in
if that doesent help your phones usb is **** or the cable is ****
btw, i have tried installing all the proper driver from the proper threads... 32 bit, 64 bit, ive tried kies and kies mini for vibrant, heimdall drivers also.... NOTHING WORKS...
i appreciate everones help... thank you.
This is what I do to get it working. I open odin first and load all the needed files.
I then plug the usb cord into the usb first before plugging it into the phone.
with odin open and the phone completely off. I hold down the volume rocker and plug in the usb. I get download mode to work almost everytime.
For me the stock cable I got with mine doesnt work. I have to use a different cord or it acts like it doesnt see my phone.

[Q] Unfixable Problem... Someone Help

Hi,
I've had a useless X10 here for months. I've done everything to try and reinstall the firmware including SEUS, Update Service and Flashtool. Nothing works and I cannot access my phone.
I was hoping I could get it working with the new flashtool. After running it and connecting the phone, it's giving me the error:
12/000/2011 22:00:44 - ERROR - Error flashing. Aborted
12/000/2011 22:00:44 - INFO - Now unplug the device and power it on
12/000/2011 22:00:44 - INFO - Then go to application settings
12/000/2011 22:00:44 - INFO - turn on Unknown Sources and Debugging
The problem I'm having is, I haven't been able to get my x10 to turn on. Is there a way to flash without having debugging enabled?
Thanks.
Try to reinstall the drivers
are you rooted?
Sent from my X10 using XDA Premium App
Have you looked at this? http://forum.xda-developers.com/showthread.php?t=928343
Try this:
1 - remove the battery and wait for 4 - 5 minutes;
2 - reinsert the battery;
3 - put your phone to charge in a wall socket (not thru USB);
4 - leave it charging for about 3 - 4 hours (check if the led is on);
5 - try to flash a stock rom using flashtool.
My X10 has an issue with the battery that makes it power off and not turn on while I don't do steps 1 and 2. I've tried to reflash a stock rom, but had received the same error you have, until I put the battery to charge during the entire night. After the recharge, I was able to reflash the rom fine (altough the problem of shutting off randomsly still happens).
Hope it helps.
I've tried using flashtool after charging my phone for a good 10 hours. It takes around 4-6 hours to flash 7-8/10 files then the battery dies.
Nothings working. The new flashtool demands the phone have unknown sources and debugging enabled but I can't since I cannot access my phone.
And if it matters at all my phone was rooted with FreeX10 rom.
GTFIH X10 geeks, help me.
when it just wont work
CHARGE PHONE TOO 100% BEFORE STARTING ANYTHING.
First ALL FLASHTOOLS Have to be done in Administrator mode on your PC/laptop and this may also fix that messed up usb port you seem to have on it to. You should NEVER charge you phone for more then 2ish hours in fact it should only take about 1.5 to 2 hours if not then you have a bad one. Also you should check that your usb drivers are up to date before you start. And Be Patient.
Had the same problem last year. What you need to do is uninstall all Se software Pc Companion an Se update Sevice and all Java.
If you have a registry cleaner and or an uninstaller (not windows) like Revo Uninstaller free or Pro use it to uninstall an clean registry. (BUT NOT IN Administrator Mode only Flashtool needs this)
Do a disk clean up Local Disk C:drive/right click properties/click disk cleanup/click all boxes/Click run/clean.
Reboot wait till stack OS/drive light stops flickering (stops loading).
Yes boot again.
Reboot wait till stack OS/drive light stops flickering (stops loading).
The first boot sets up your cleanup the second boot starts a fresh boot cycle again wait for full load up light stops.
Reinstall all programs letting them update them self. JAVA first Pc Companion then Se update Service rebooting on each one NOT all at once (waiting till stack OS/drive light stops flickering (stops loading) each time.
This helps your stack/drive stay clean.
If you do not have 7zip (free) you should get it now an download an install it reboot PC (waiting till stack OS/drive light stops flickering (stops loading).
When connecting phone to PC use a different USB port then the one you used at first.
Now Start Pc Companion and let it do it's thing, do as it says, connecting phone to update Pc Companion to it.
Then do the same for Se update doing as it says and do an update and/or repair.
If it says to unplug or plugin USB just unplug/plugin the USB on the PC not the phone and making sure that you put it back in the same USB port.
Create a folder on C: drive:
Right click Start/Explore/Click (high light) Local Disk(C) click file/new/folder/
right click new folder/rename/Flashtool version ?.?.?
Download And Save to Folder you made on the C: drive
Firmware Files:
(use a Stock/Generic firmware first like 2.1.1 for your region)
http://forum.xda-developers.com/showthread.php?p=10738287#poststop
http://forum.xda-developers.com/showthread.php?p=10738467
FlashTool version ?.?.?
http://forum.xda-developers.com/showthread.php?t=920746
Install Flashtool on C: drive:
After downloading file to folder go to file and in it a rar file
Right click 7zip file/Select Extract to Flashtool ?.?.?
Reboot wait till stack OS/drive stops loading (light stops flickering).
When using Flashtool do not unplug USB from PC and when plugging in for flashing just remove battery plug mini USB in phone hold back button an put battery back in.
While Flashing NEVER TURN OFF/CLOSE FLASHTOOL until the phone is up and working completely.
After putting firmware in folder.
Right Click/x10Flashtool/Click Run As Administrator.
And follow the instruction in all the guides and all should be good.
NOW READ THIS POST FIRST
And use a STOCK FIRMWARE to get started with and watch the video and he has other one for how to's
http://www.youtube.com/watch?v=B9_pFOxPJUY
http://forum.xda-developers.com/showthread.php?t=928343
SE Firmware Files
http://forum.xda-developers.com/showpost.php?p=10879519&postcount=2
And this thread it has some good stuff.
http://forum.xda-developers.com/showthread.php?t=955703
Thank you DooMLoRD Senior Member For Guides,Tools and Roms.
Please remember to Please Click the Thanks button if this helped you. For all the Developers in the posts. A lot of work went in to this stuff.
^ Thank's for the lengthy post although I followed the first set of instructions and still the same problem (takes over 6 hours,doesn't flash, battery dies).
With the SDK what would I have to learn to fix the phone?
Can you get in to xrecovery if you can clear all. If not try pluging in to usb xrecovery should come up. Sorry so late I'm not at my pc all update this when i get home.
Sent from my X10a using XDA Premium App
make sure you have a sim card in the phone, that might get you past your problems
Do you have x10.sin in loaders in flashtool?
Is your USB cable connected through a hub? There is absolutely no reason it should take anywhere near that long to flash unless your connection is to slow. I tried flashing while plugged through a passive hub and it would get to ~70% and fail everytime until I plugged directly into the PCs USB port. Flashing should only take a few minutes if you have a good USB connection.
Sent From My *Super Fly X10*
If I (or anyone for that matter!) help you, dont be afraid to press THANKS!
Its your battery. Its not charging correctly. U may need a new one since u can't turn it on
Sent from my X10i using XDA Premium App
Did you get it fixed ?? Phone power should be at least 60% when you start anything
To get in to xrecovery turn off phone wait 5 seconds then turn on phone and pressing the back button tell it comes up if it doesn't try again and if it still doesn't then you didn't do something right.
Also try SU update repair.
Try turning off phone plug in usb to phone then pc then turn on phone if you flashed right xrecovery should come up on phone then scroll down with volume button to advanced setting clear all then re-flash Firmware. if not re-root install xrecovery if that does not work start ALL over from start with my first post on the 24th. my guess is you are missing some steps.
@GravvyTrain
Yes I do have a Sim card in the phone, problem remains the same
@Dusza Spc
Yes I do have the x10.sin file in flashtool
@CMoney87
Not using a hub, directly into my laptop USBS. Also tried on various computers, same problem. It's the phone.
@Lion3494
I doubt it's my battery, I've used another and same problem.
@Patricks_book
Have not fixed the problem. I literally can't access anything on the phone, When you press the power button it vibrates and thats it. I've tried accessing Xrecovery and It doesn't do anything.
I've tried SU Update Repair and it gives me a network error (I've disabled firewalls, tried on another computer) and It doesn't allow me to go any furthur (wrote the exact error in a previous thread).
I haven't missed any steps, It just doesn't flash.
Awesome to make things even better, my phone won't go green when on USB.
Put the phone onto charge and all it gives me is blinking red light.
Goodnight sweet X10.
foxhound494 said:
Hi,
I've had a useless X10 here for months. I've done everything to try and reinstall the firmware including SEUS, Update Service and Flashtool. Nothing works and I cannot access my phone.
I was hoping I could get it working with the new flashtool. After running it and connecting the phone, it's giving me the error:
12/000/2011 22:00:44 - ERROR - Error flashing. Aborted
12/000/2011 22:00:44 - INFO - Now unplug the device and power it on
12/000/2011 22:00:44 - INFO - Then go to application settings
12/000/2011 22:00:44 - INFO - turn on Unknown Sources and Debugging
The problem I'm having is, I haven't been able to get my x10 to turn on. Is there a way to flash without having debugging enabled?
Thanks.
Click to expand...
Click to collapse
try the flashtool in windows 7 32bit
even i have the same problem same as foxhound494 pls help
a2441918 said:
even i have the same problem same as foxhound494 pls help
Click to expand...
Click to collapse
Maybe try plugging in the usb on the back on the computer

Rooting guide of Intratech DOES work! :)

Hi all! The rooting guide of Intratech given here : http://forum.xda-developers.com/showthread.php?t=1075278 DOES NOT WORK! I have an SGS II Kernel version of KE8 (India) and I tried to follow the steps given in the guide, but when I open ODIN and connect my phone in Download mode with my laptop via USB Cable, ODIN is not connecting to the phone. The box meant to turn yellow does NOT change color. Nothing happens at all. Why is this so? I cannot post in the relevant thread because I am a newbie in the forun
Have you installed kies first to get the drivers?
Sent from my GT-I9100 using XDA Premium App
Yes, of course, I have the latest version of Kies installed on my laptop and I use it regularly to connect with my SGS II. I kept Kies closed when trying the rooting procedure as mentioned in Intratech's guide. Started phone in download mode. Opened Odin on laptop, then connected phone via USB........the box which is supposed to turn yellow on connection, doesn't light up. Nothing happens at all.
TheMegastar said:
Hi all! The rooting guide of Intratech given here : http://forum.xda-developers.com/showthread.php?t=1075278 DOES NOT WORK! I have an SGS II Kernel version of KE8 (India) and I tried to follow the steps given in the guide, but when I open ODIN and connect my phone in Download mode with my laptop via USB Cable, ODIN is not connecting to the phone. The box meant to turn yellow does NOT change color. Nothing happens at all. Why is this so? I cannot post in the relevant thread because I am a newbie in the forun
Click to expand...
Click to collapse
I suggest to you that the overwhelming majority of the people who use the guide will disagree with you and provide evidence to the fact that it does, indeed, work. The fact that it does not work for you suggest that you are doing something wrong or have a problem with your computer.
I would suggest that you ensure that KIES is also closed in the system tray of your computer before opening Odin and connecting the phone. Also ensure that your computer has an internet connection and is able to connect to windows update to download and install drivers. If that doesn't work then change USB port or computer.
By all means, if you find a way that works then feel free to write your own guide. More information is good and maybe others might find your method, if you discover one, easier to follow.
@Intratech: Hi. Thanks for your reply. Ok, so it is not working for me. Can you help?
My laptop is working on Windows 7 Home Premium which is upto date in all respects. My USB port is working fine as I am able to connect my SGS II to Kies through that. Kies was closed when I tried to connect to Odin. Odin version is 1.85. While the phone (in download mode) is connected to the laptop, and Odin is Open, nothing happens. Nothing.
TheMegastar said:
@Intratech: Hi. Thanks for your reply. Ok, so it is not working for me. Can you help?
My laptop is working on Windows 7 Home Premium which is upto date in all respects. My USB port is working fine as I am able to connect my SGS II to Kies through that. Kies was closed when I tried to connect to Odin. Odin version is 1.85. While the phone (in download mode) is connected to the laptop, and Odin is Open, nothing happens. Nothing.
Click to expand...
Click to collapse
Is kies closed in the system tray as well?
Yes, Kies is closed in system tray also. Fully closed. Odin opens, and I see the Odin screen as per your screen shots, but the box which is supposed to light up yellow, does not.
Are you using the Samsung USB cable or a HTC one?
Samsung USB cable which came with the phone box pack. I can see the Auto Reboot and F. Reset Time boxes checked. Nothing else is checked, not even the PDA button. The box saying ID:COM (which is supposed to light up) is blank.
u need to check pda and load the file u want to flash it
then click on start
Look in your program and features list, found in control panel, and see if you have a listing for Samsung USB driver for mobile phones there. If you do then uninstall it and uninstall KIES. Download a new copy of KIES from Samsung and install it. After installing it, make sure you don't have USB debug ticked, connect the phone and leave it until all the drivers install. After that remove the device and lose KIES. Put the tick in USB debugging and connect the phone and leave it so that any needed drivers install. After this put the phone in download mode and connect it, without opening KIES or ODIN, and leave it to download any drivers needed. If it downloads and install any drivers wait for it to finish, once it does then you can go ahead and use Odin normally.
If this doesn't work your PC is at fault, fix it.
cyberwarfare said:
u need to check pda and load the file u want to flash it
then click on start
Click to expand...
Click to collapse
How you going to flash without connecting to the device?
Turn USB debugging off on phone .USB connection should be to a motherboard port .
Reboot phone set phone to connect in USB mass storage mode .
Connect cable wait for Windows to load drivers . You should be able to browse phone via Windows explorer if USB drivers are correct .If so remove cable and reboot phone to download mode . Open Odin select files to load connect cable .
That fails then
Rooting guide of intratech does not work! for you your PC or your phone but for everyone else so give up .
jje
@cyberwarfare: Yes, I tried that. The file loaded, I pressed start. Yet nothing happened. I just saw one line notification in the left hand side column of Odin, which read something like "successes: 0/failures: 0". I am speaking from memory here. Nothing really happened even after loading PDA and pressing the Start button.
@Intratech: Yes, both Kies and Samsung USB Driver for Mobile Phones are there in my program list. I downloaded Kies from their India support site : http://www.samsung.com/in/support/d...1&prd_mdl_cd=GT-I9100LKAINU&srchword=GT-I9100
Worth mentioning here that the USB debug check box was ticked when I tried to Root with Odin.
So basically, you're asking me to uninstall & reinstall Kies and its drivers. Ok, will do. It will take time so will do it when I have a little more time on my hands. Thanks for your help & your time. I appreciate. If you have time, then look at my other post here which says, "7 major issues with SGS II" ...... and help with solving my other issues like that of bluetooth not connecting and phone ringer's erratic behaviour. Thanks a ton.
Mate I haven't used the Indian firmware so I'm not too sure about troubleshooting it. There is an Indian thread in the general forum where you may be able to get more help with the issues you have.
@JJEgan: Thanks for replying. All my USB Ports are on the motherboard itself, worth mentioning that the same USB port works fine when I connect the phone to the laptop. Am able to transfer files to and fro via the same USB port.
"set phone to connect in USB mass storage mode".....how do I do that? Where to find that in phone settings?
I am able to browse the contents/files on the phone very well...so this proves my drivers are fine. So which basically means, that Intratech's rooting guide does not work FOR ME! Happy? This may be a problem specific to the India specific phones....Kernel version is 2.6.35.7-I9100XWKE8-CL214845
[email protected] #2
PDA : I9100XWKE8
Phone : I9100DDKE2
CSC : I9100ODDKE2
Build Info : Wed May 18 13:55:45 KST 2011
@Intratech: Thanks mate. I've posted my problem in the India specific thread also.....lets see if someone replies. But the problem is not with the rooting procedure, the problem is that I can't even seem to get started with the procedure as there is no connection between Odin and the phone.
Nah, it's not with the firmware. The other Indians who use it have no issue following the guide.
Please try and reinstall everything as I've stated and see if that work. Also, when you go into download mode what do you see on the screen?
In download mode I see a static warning on the screen which tells me of the risk and tells me I have to press the VOL down button to cancel this, and there is a yellow triangle at the bottom. The screen stays there as I connect the USB cable to the laptop.
TheMegastar said:
In download mode I see a static warning on the screen which tells me of the risk and tells me I have to press the VOL down button to cancel this, and there is a yellow triangle at the bottom. The screen stays there as I connect the USB cable to the laptop.
Click to expand...
Click to collapse
You need to read the instructions start off by reading what it says on that screen .Do not read half of the instructions like you are its very dangerous flashing if you cannot read and follow the instructions and i advice you dont flash .
The screen message you are not reading is the sentence above the one you posted .
To install custom rom press Vol Up key .
jje
TheMegastar said:
In download mode I see a static warning on the screen which tells me of the risk and tells me I have to press the VOL down button to cancel this, and there is a yellow triangle at the bottom. The screen stays there as I connect the USB cable to the laptop.
Click to expand...
Click to collapse
Right this is your problem, you have not put the phone in download mode as yet. Press volume up at this screen to enter download mode and now you will connect.

[Q] Windows Not Recognizing Device

Hi guys, was having a few problems with my phone and decided that I'd flash the stock ROM again.
Went into ODIN as you do, and as I was flashing the stock ROM, for some reason or another I heard the disconnect/reconnect noise that Windows makes when you remove a device then FAIL came up in ODIN.
Now my phone's stuck with a phone connecting to a computer on the charge screen, it can't go into recovery mode but it can go into download mode.
Tried connecting it to my PC in download mode, and even though I've got the Samsung USB Drivers installed I get the 'USB Device Not Recognized' message, which means I can't flash the stock ROM in ODIN anymore.
Does anyone have any advice? Thank you.
JoshS2 said:
Hi guys, was having a few problems with my phone and decided that I'd flash the stock ROM again.
Went into ODIN as you do, and as I was flashing the stock ROM, for some reason or another I heard the disconnect/reconnect noise that Windows makes when you remove a device then FAIL came up in ODIN.
Now my phone's stuck with a phone connecting to a computer on the charge screen, it can't go into recovery mode but it can go into download mode.
Tried connecting it to my PC in download mode, and even though I've got the Samsung USB Drivers installed I get the 'USB Device Not Recognized' message, which means I can't flash the stock ROM in ODIN anymore.
Does anyone have any advice? Thank you.
Click to expand...
Click to collapse
Try installing samsung kies. The usb drivers are included.
princeownt said:
Try installing samsung kies. The usb drivers are included.
Click to expand...
Click to collapse
I have it installed, and I installed the USB drivers from the soft bricked sticky in this section. Neither have helped.
Hi!
Hi, you guys install ADB on your system? And also USB debugging mode on the phone?
Should be turned on which can be done by going to Settings>Applications>Development and select USB debugging.
Try this, for me its works
MafiaDroid said:
Hi, you guys install ADB on your system? And also USB debugging mode on the phone?
Should be turned on which can be done by going to Settings>Applications>Development and select USB debugging.
Try this, for me its works
Click to expand...
Click to collapse
I can't even turn the phone on at the moment. Only thing I can do is go into Download mode.
Help
Try this, take out the battery, then press and hold the ON button for 7-10 seconds (the longer the better). Reinsert the battery, then press ON button to start it. This is a soft reset, and wipes the temporary memory and empties all remaining power in the circuits. This helps on many phones and even laptops that won't start properly or show anything on screen.
If this does not work, try the next step. Again, do as above. But after inserting the battery, do not turn the phone on, but press and hold the ON button and the HOME button at the same time for 7-10 seconds. This is a hard reset, and works best if done after a soft reset. Just be sure the battery has at least some juice in it and isn't empty. If possible, try with another battery if this does not work.
Hope this helps!
Try going to device manager, you will probably find your device as an unrecognized device, uninstall the drivers, unplug and then plug it again and see.
if the prblm is hard then do a fresh installation of kies,device etec etc.....but if u have ur device in the device list on pc then first uninstall it...if possible try recovery mode and reset...
I tried everything you guys have suggested and none of that worked. Anyone else got any ideas?
Try everything (and I mean everything) on the following list. Given the problems you've had & that you've already tried some of these things, I'd try another PC. And if it doesn't work first go on another PC, then go thru the list & try everything on the 2nd PC.
*Ensure Kies & it's processes aren't running in Windoze task manager. Kill them if they are.
*Try different USB ports; you must be using a 'powered' or mainboard port.
*Try different USB cables (particularly the cable that came with the phone if you're not using it now)
*Try different versions of Odin (search on here/Google)
*Uninstall Kies, reboot, redownload & reinstall it, reboot, try the flash again. Also run Windoze Update.
*And if all this fails, try a different PC.
Tried all the above and a different PC.
It didn't work. I could fix the phone if the computer would pick up that the phone's connected - it just doesn't.
Total Removal of KIES including registry entries .
Reboot PC install a new copy of Kies .
Phone backup data and factory reset .
Set phone to USB storage mode using the Samsung cable connect to PC and wait for Windows to find USB drivers .Remove cable reboot phone .
Start Kies connect with cable wait for Kies to find the phone .
Note USB Debugging OFF and cable connects to a direct motherboard port only .
Nothing then only further suggestion would be to Format the PC and start over with a clean Windows install .
jje
I can't turn the phone on, it's stuck on the phone, triangle, PC screen.
I've tried fresh installs on three different PC's.
JoshS2 said:
I can't turn the phone on, it's stuck on the phone, triangle, PC screen.
I've tried fresh installs on three different PC's.
Click to expand...
Click to collapse
That's a forced download mode.
Try a blind flash to a stock firmware from Odin while connected to your computer with the phone on this screen. Even if Odin doesn't seem to register that it's connected. I've heard of at least one person this worked for.
At this point, you really have nothing to lose by trying this.
Bit of an update, I plugged it in again and it installed some drivers and ODIN picked it up. Only for it to disconnect a few moments later, now it keeps disconnecting and reconnecting over and over but ODIN's not picking it up.
JoshS2 said:
Bit of an update, I plugged it in again and it installed some drivers and ODIN picked it up. Only for it to disconnect a few moments later, now it keeps disconnecting and reconnecting over and over but ODIN's not picking it up.
Click to expand...
Click to collapse
I know you said you tried a different cable, but that sounds suspiciously like a bad cable.
It's not the cable, thanks any way.
Update 2: I managed to get it to connect long enough to flash the stock Kernel. Still didn't reboot. Then I connected it again and flashed the stock ROM, which bricked it again. Then I flashed the stock kernel and it works!
However, there is a problem:
When the phone gets turned off, it constantly shows the charging battery icon with warning triangle and a thermostat next to it. I can't turn the phone on because of this unless I go into Recovery mode and reboot system.
Any ideas? Thanks.
JoshS2 said:
It's not the cable, thanks any way.
Update 2: I managed to get it to connect long enough to flash the stock Kernel. Still didn't reboot. Then I connected it again and flashed the stock ROM, which bricked it again. Then I flashed the stock kernel and it works!
However, there is a problem:
When the phone gets turned off, it constantly shows the charging battery icon with warning triangle and a thermostat next to it. I can't turn the phone on because of this unless I go into Recovery mode and reboot system.
Any ideas? Thanks.
Click to expand...
Click to collapse
Now this sounds like a faulty/dirty/bad usb port.
ctomgee said:
Now this sounds like a faulty/dirty/bad usb port.
Click to expand...
Click to collapse
This was my original thought and my reasoning for flashing a stock ROM in the first place!
JoshS2 said:
This was my original thought and my reasoning for flashing a stock ROM in the first place!
Click to expand...
Click to collapse
I in no way recommend this, and not sure I would do it if I ever started having this issue...
BUT - I have heard that some people faced with this condition have fixed it by physically moving the small wafer board inside the USB port with a precision screwdriver (gently!) to a more "centered" position.
If that doesn't work, look at replacing that part. Either via warranty service if you still have it, or a service center.

Categories

Resources