I flashed the x10 wildfire HTC port onto my mini just to screw around but when i rebooted and tried to go into xrecovery it didnt work. I tried doing it via x10 flasher and that didnt work also. is there any way of getting this thing back into xrecovery? I have nandroid backups i can refer back to
You will need to reflash your device using SEUS.
Sent from my U20i using XDA Premium App
nujhum said:
You will need to reflash your device using SEUS.
Sent from my U20i using XDA Premium App
Click to expand...
Click to collapse
....,then install xrecovery again and then restore your backups.
Thx a lot worked like a charm
Sent from my Dell Streak using XDA App
Another method, you can just hard reset.
When you open the back plate, There's should be a small button next to the camera. You'll need something small to press the button, around 10sec. That should do the hard reset.
Sent from my U20i using XDA Premium App
nujhum said:
You will need to reflash your device using SEUS.
Sent from my U20i using XDA Premium App
Click to expand...
Click to collapse
I do the same as flashing with wildfire rom for my x10 mini, so now my phone wont start, nothing hapend when i try to turn it on, i also charge it with my wall charge and with my usb port on my pc, it turned on by its self and stuck at sonyericson logo. and then, I try to charge the battery for hours and then take out of the battery for 5minutes and then plug it in, after that try to get flash mode but it cant go in to flash mode, so anybody help me?
dtbang721 said:
I do the same as flashing with wildfire rom for my x10 mini, so now my phone wont start, nothing hapend when i try to turn it on, i also charge it with my wall charge and with my usb port on my pc, it turned on by its self and stuck at sonyericson logo. and then, I try to charge the battery for hours and then take out of the battery for 5minutes and then plug it in, after that try to get flash mode but it cant go in to flash mode, so anybody help me?
Click to expand...
Click to collapse
OK
put out the battery
plug in the usb in your PC and phone when SEUS ask for your device
press the back button and put the battery back in your phone
and......................FLASHMODUS
dtbang721 said:
I do the same as flashing with wildfire rom for my x10 mini, so now my phone wont start, nothing hapend when i try to turn it on, i also charge it with my wall charge and with my usb port on my pc, it turned on by its self and stuck at sonyericson logo. and then, I try to charge the battery for hours and then take out of the battery for 5minutes and then plug it in, after that try to get flash mode but it cant go in to flash mode, so anybody help me?
Click to expand...
Click to collapse
im not sure about mini course i own a mini pro...
since mini doesn't have battery, so it will automatically turn off even after your turn it of.
so, okay. im not sure, but open the back plate of your mini, look near the camera, there's should be a small white button, i think its for hard reset.
try pressing it and hold for 5-10seconds. see if it works for you..
flex96 said:
OK
put out the battery
plug in the usb in your PC and phone when SEUS ask for your device
press the back button and put the battery back in your phone
and......................FLASHMODUS
Click to expand...
Click to collapse
lol, there's no battery for mini, there's only build in battery for mini. so that would be impossible.... D
nujhum said:
lol, there's no battery for mini, there's only build in battery for mini. so that would be impossible.... D
Click to expand...
Click to collapse
I've got tools to take out the x10 mini battery, it isnt difficult for me.
I've tried the guide of seus program (turn off for minutes, plug the usb cable to pc, hold the back button, plug usb cable to the phone) but there is no thing happened affter I hold the back button and plug usb cable to the phone, no green led indicate thats flash mode. im sure that the battery is full because i charge it for hours with my wall charger. and the battery has out for minutes before i tried to flash mode.
dtbang721 said:
I've got tools to take out the x10 mini battery, it isnt difficult for me.
I've tried the guide of seus program (turn off for minutes, plug the usb cable to pc, hold the back button, plug usb cable to the phone) but there is no thing happened affter I hold the back button and plug usb cable to the phone, no green led indicate thats flash mode. im sure that the battery is full because i charge it for hours with my wall charger. and the battery has out for minutes before i tried to flash mode.
Click to expand...
Click to collapse
Seus always work to me when I bricked my phone or loop boot at sony ericsson logo.
You sure you did follow the instruction step by step?
Sent from my U20i using XDA Premium App
nujhum said:
Seus always work to me when I bricked my phone or loop boot at sony ericsson logo.
You sure you did follow the instruction step by step?
Sent from my U20i using XDA Premium App
Click to expand...
Click to collapse
Could you please tell me how to do it step by steps? The SEUS doent work for me in my case. All I do is:
1- Charge the phone for hours to full up the battery
2- Take out the x10 mini battery so the phone is surely turn off for minutes
3- Plug the battery in.
4- Plug the cable (come with the phone - sonyericson cable)
5- Hold the back button on my phone
6- Plug the cable to my phone while the back button still pressed
7- Affter five minutes. No thing happened, the green led not appear, the phone only has red blink.
all I can do is charge the phone and see that it automatic turn on and stuck at sonyericson logo.
dtbang721 said:
Could you please tell me how to do it step by steps? The SEUS doent work for me in my case. All I do is:
1- Charge the phone for hours to full up the battery
2- Take out the x10 mini battery so the phone is surely turn off for minutes
3- Plug the battery in.
4- Plug the cable (come with the phone - sonyericson cable)
5- Hold the back button on my phone
6- Plug the cable to my phone while the back button still pressed
7- Affter five minutes. No thing happened, the green led not appear, the phone only has red blink.
all I can do is charge the phone and see that it automatic turn on and stuck at sonyericson logo.
Click to expand...
Click to collapse
i see.
just maybe.
2- Take out the x10 mini battery so the phone is surely turn off for minutes
(do not plug in the battery yet)
4- Plug the cable to pc
(you need to do step 5 & 6 as fast as you can so your phone wont switch on)
5- insert the battery,
6- press and hold back button, plugin usb. that should work.
May be the battery isnt enought to begin flash mode because when I hold power button there is nothing happend, im not sure that battery could be charge when I conect to charger. when I conect to charge, the red light blink, affter about five minutes the phone turn it self on and stuck at sonyericson logo. So there is no red blink more, only the logo. So in this case I think that affter charge 5 minutes the phone turn on and no charge any more, and 5 minutes charging is not enough for flash mode. But I have no way for charging my phone.
dtbang721 said:
May be the battery isnt enought to begin flash mode because when I hold power button there is nothing happend, im not sure that battery could be charge when I conect to charger. when I conect to charge, the red light blink, affter about five minutes the phone turn it self on and stuck at sonyericson logo. So there is no red blink more, only the logo. So in this case I think that affter charge 5 minutes the phone turn on and no charge any more, and 5 minutes charging is not enough for flash mode. But I have no way for charging my phone.
Click to expand...
Click to collapse
have you try pressing the hard reset button at the back of the phone?
it should be around next to the camera, white button and very small. need to plress it with pin anything smaller.
If I'm not mistaken, mini does not have hard reset button. Try to find some pictures of disassembled mini and you'll find out that its not a button at all.
The only way to perform hard reset on mini is to hold down both power and Home keys.
Sent from my U20i using XDA App
sur1k said:
If I'm not mistaken, mini does not have hard reset button. Try to find some pictures of disassembled mini and you'll find out that its not a button at all.
The only way to perform hard reset on mini is to hold down both power and Home keys.
Sent from my U20i using XDA App
Click to expand...
Click to collapse
my bad. LOL i thought its the same with mini pro. (i own a mini pro.)
So may be affter my phone crashed. It cant charge as normal. It can only charge in about 5 minute and turn on by it self and stop charging. I wonder how to charge it before flashing?
dtbang721 said:
So may be affter my phone crashed. It cant charge as normal. It can only charge in about 5 minute and turn on by it self and stop charging. I wonder how to charge it before flashing?
Click to expand...
Click to collapse
using external charger i think.
i faced a similar issue once.
battery discharged and phone bricked. i then connected my phone to the usb with the laptop. phone was looking dead but it did charge and turned on, and i kept it that way for 5 to 10 mins, and then flashed it, it hardly takes 3 - 4 mins to flash...
and then i kept it to be charged again
Sent from my U20i using XDA Premium App
Related
Hi all.
My phone seems to be broken. It's almost completely dead. When I press the power button the led blinks red three times. When I connect it to power it blinks red once every other second. Anyone knows what this red blinking means? I'm sure it's a code for something...
I've tried removing sd and sim and also disconnecting and connecting the battery cable with no result. Anything else I could try or is it just a matter of sending it away and being without phone for some weeks?
/Daniel
Battery is completly drained. Charge it about half an hour and should work.
Yeah, I've been pretty scared too when this happened for first time to me. It is really weird behavior. Atleast it is working again.
wiilweer said:
Battery is completly drained. Charge it about half an hour and should work.
Click to expand...
Click to collapse
Yep, you're right. 20 minutes and the phone came alive.
Is it just me or did they completely miss this out in the manual? Could have been worth mentioning if you ask me...
/Daniel
i've had this too... is it ok to charge via a PC or does it have to be directly from the charger?
x10bravia said:
i've had this too... is it ok to charge via a PC or does it have to be directly from the charger?
Click to expand...
Click to collapse
I guess its the same but charging it via the usb will take more time to get it alive again
HELP
my phone can´t charge anyway.... i let it charging in the wall during all the morning and "nothing"... even a minimum led light...
so i connected to the usb in my pc and the led started blinking once in each three seconds...
blink + 1 + 2 + 3sec AND REPEAT
so... i let it in usb for maybe 40 minuts... and.... nothing again... nothing changed and the led continuous to blink at the same way.
so, i tried to plug again in the wall, and no led light, but suddently led blinked this way:
blink / blink / blink + 1 + 2sec and repeat three times so stops, no more lights, and it happend again if i tryied to power on the phone...
and now, nothing happens.... no lights... even i fi try to power on, even if i plug in the wall...
mini pro is dead.
i don´t know what to do
tried pressing home + power buttons for minuts and nothing
tried pressing back button for minuts and nothing
tried to connect to PC companium and nothing, no phone connected
tried using SEUS but it can´t connect to the phone as it has no battery charge
any ideas.... please?
and let me know... is this any issue from the ROM? i just installed CM7Mini V7... it´s the first time i had the battery drained... so i ask... if there is a way to awake my mini, will the same issue happen again ????? I can´t forget the battery draining?????
HEEEEEEEEEELLLLLPPPPP
3 blinks mean not enough battery energy to boot. Maybe your USB port is just brocken...
Try using FlashTool to flash a stock ROM to see if it works, because with SEUS first you have to connect your phone to be recognised and afteerwards updated or repaired. Maybe FlashTool is the solution...
I have made a post with instructions and links to flash with FlashTool. Just search for
2.1.1.A.0.6 GREEK .ftf
Another possible solution is what guys have mentioned above... To let it charge while it seem dead and it'll be alive in some minutes.
Sent from my U20i using XDA Premium App
Some custom rom wont charge while the X10 mini pro is turned off. So it needs to be on for charging. This is challange is its totaly dryed out
So never let it dry totaly out.
Emperor.dk said:
Some custom rom wont charge while the X10 mini pro is turned off. So it needs to be on for charging. This is challange is its totaly dryed out
So never let it dry totaly out.
Click to expand...
Click to collapse
(you probably meant no offline charging)
It really doesn't matter... I have tried almost every single ROM. And dryed the battery completelly, but I was always able to charge it.
Sent from my U20i using XDA Premium App
leajian said:
(you probably meant no offline charging)
It really doesn't matter... I have tried almost every single ROM. And dryed the battery completelly, but I was always able to charge it.
Sent from my U20i using XDA Premium App
Click to expand...
Click to collapse
Yes...
Thanks
Thanks for the info. Pluggin the phone did the trick.
Help
azhhael said:
my phone can´t charge anyway.... i let it charging in the wall during all the morning and "nothing"... even a minimum led light...
so i connected to the usb in my pc and the led started blinking once in each three seconds...
blink + 1 + 2 + 3sec AND REPEAT
so... i let it in usb for maybe 40 minuts... and.... nothing again... nothing changed and the led continuous to blink at the same way.
so, i tried to plug again in the wall, and no led light, but suddently led blinked this way:
blink / blink / blink + 1 + 2sec and repeat three times so stops, no more lights, and it happend again if i tryied to power on the phone...
and now, nothing happens.... no lights... even i fi try to power on, even if i plug in the wall...
mini pro is dead.
i don´t know what to do
tried pressing home + power buttons for minuts and nothing
tried pressing back button for minuts and nothing
tried to connect to PC companium and nothing, no phone connected
tried using SEUS but it can´t connect to the phone as it has no battery charge
any ideas.... please?
and let me know... is this any issue from the ROM? i just installed CM7Mini V7... it´s the first time i had the battery drained... so i ask... if there is a way to awake my mini, will the same issue happen again ????? I can´t forget the battery draining?????
HEEEEEEEEEELLLLLPPPPP
Click to expand...
Click to collapse
is ur prob get solved pls tell me, im suffering from this now........ i charged my mob 15 hrs.... but still red light blinks.....!!! Help pls!!!
Raj Rohit said:
is ur prob get solved pls tell me, im suffering from this now........ i charged my mob 15 hrs.... but still red light blinks.....!!! Help pls!!!
Click to expand...
Click to collapse
I had today same problem. i was on my phone and battery was 100%. i have just disconnected from charging.. and after few minutes phone turns off and when I press power button nothing except 3 x red led flash. if I turn charger red led blinks. I let 1 hour to charge my phone and led was green but if I push power button nothing againg..no vibrate nothing. I pulled out battery few times and put back and finally phone turns on
also before i give my phone on charging I put my battery into sisters phone (i have x8 and she xperia mini st15i) and her phone turns on with that battery, i put back to my phone and it didnt turn on my phone. (I dont understand that) but after all my phone works now and Im happy
so try only charge for few hours and it should start also try put battery into another phone to see what is problem
w3rew0lf said:
I had today same problem. i was on my phone and battery was 100%. i have just disconnected from charging.. and after few minutes phone turns off and when I press power button nothing except 3 x red led flash. if I turn charger red led blinks. I let 1 hour to charge my phone and led was green but if I push power button nothing againg..no vibrate nothing. I pulled out battery few times and put back and finally phone turns on
also before i give my phone on charging I put my battery into sisters phone (i have x8 and she xperia mini st15i) and her phone turns on with that battery, i put back to my phone and it didnt turn on my phone. (I dont understand that) but after all my phone works now and Im happy
so try only charge for few hours and it should start also try put battery into another phone to see what is problem
Click to expand...
Click to collapse
have you found a solution?
rfg13 said:
have you found a solution?
Click to expand...
Click to collapse
I dont know what was wrong but phone now works like a charm. I dont have that phone but my friend does and it didn't happened again
I got same problem and tried charging my phone but it didn't work. Please suggest me what else I can do.
Not sure if this did the trick, but after I had the battery out for about 5 minutes, it started after inserting back.
wiilweer said:
Battery is completly drained. Charge it about half an hour and should work.
Click to expand...
Click to collapse
I have a same problem now. Even when I have my Xperia Z on charge now , the red LED doesn't light up. I hope this works for me.
My X10a is having a problem. It won't turn on and the red led just flashes. I tried buying a new battery off of ebay but that didn't work.
What else can I try to make it work?
Can you get into the flash mode?
hasei said:
Can you get into the flash mode?
Click to expand...
Click to collapse
How do I do that?
When you use SEUS or flashtool, you need to turn the power on with the back button holding down. If the LED on upper right remains green, it means the phone got into the flash mode.
My point is that if you can get into flash mode, you can at least flash a SE stock firmware and see if your inability to power up is firware related or not.
I had the same problem. i charged over night, in the morning, the green light went on but I messed up again. so what I did is plugged it into a car charger and drove on the freeway for a while. once I got it up to 180 Km/h and Bing, the green light went on. I let it charge for a while, then went home and used SEUS to repair it, and when I did that, I charged it over night and Walla, it works like a charm. i read everywhere, and someone else has a way to find a charger with a higher voltage, and splice the wires to your charger, but I remember my phone only charging in my car when I pull out, so I figured I could get a high enough voltage, and I did. you could also try just revving your engine.
Sent from my X10i using XDA Premium App
Okay so I tried to get into flash mode, but didn't have any luck. When I plug in the phone into my computer the phone has the red led blinking.
nikmash232 said:
Okay so I tried to get into flash mode, but didn't have any luck. When I plug in the phone into my computer the phone has the red led blinking.
Click to expand...
Click to collapse
I have the same problem, nothing works, even if I charge it all the night. When I try to turn it on it the red led just blink 3 times and I can't put it on flash mode.
Any idea?
Not sure if you understood getting into flash mode correctly.
1) First you turn the phone off completely.
2) Load up flashtool and your desired stock rom. Be sure to have wipe data checked off.
3) When the flashtool tells you to plug the device in you hold the back button down and attach the usb cable. The light should remain green during the flashing process.
Sent from my X10i using XDA App
kindred7 said:
Not sure if you understood getting into flash mode correctly.
1) First you turn the phone off completely.
2) Load up flashtool and your desired stock rom. Be sure to have wipe data checked off.
3) When the flashtool tells you to plug the device in you hold the back button down and attach the usb cable. The light should remain green during the flashing process.
Sent from my X10i using XDA App
Click to expand...
Click to collapse
That's exactly what I did. Is there anything else I can do?
could it be because I don't have the OEM cable?
sony
remove battery for 30 min..
Hey guys I've got a problem with the xperia x10 from my friend it won't turn on and it doesn't load when I plug it to the pc nothing happens same with the power adapter I dissambleyd it and there was nothing broken
Pls help me and sry for my bad English
Pls move if its the wrong category ! Thx again !
Sent from my HTC Wildfire S A510e using XDA App
You should take the to the x10 forum but it sounds like the usb is broken which is a known problem.
Sent from my X10a using XDA Premium App
Doesn't look so I dissambleyd it and the connector looks fine no pin seems to be disconnected :s
Sent from my HTC Wildfire S A510e using XDA App
try letting it load for some while, try different cables, try connecting in flash mode with the flash tool and SEUS repair, if nothing works it looks ugly.
try this http://www.youtube.com/watch?v=HmX-IYNYqL8
Ok thanks I give it a try I tell you if it works ! And thanks for the quick answers
Sent from my HTC Wildfire S A510e using XDA App
I do it exactly like in the video step by step but nothing happens no led ligth up or blink I try now to figure out if there is still power in the battery and if the power comes to the connector I tell you my results !
Greets and Thx again
Sent from my HTC Wildfire S A510e using XDA App
Dan1993 said:
Hey guys I've got a problem with the xperia x10 from my friend it won't turn on and it doesn't load when I plug it to the pc nothing happens same with the power adapter I dissambleyd it and there was nothing broken
Pls help me and sry for my bad English
Pls move if its the wrong category ! Thx again !
Sent from my HTC Wildfire S A510e using XDA App
Click to expand...
Click to collapse
I had the same problem this morning. I went to bed last night and the phone was fine. This morning it wasn't booting up at all, I wasn't even getting the SE logo.
I was able to fix it with SEUS: plugged in the USB port while holding the Back key and the device turned on in Flash mode so I was able to flash it.
Hope it helps.
burshturs said:
I had the same problem this morning. I went to bed last night and the phone was fine. This morning it wasn't booting up at all, I wasn't even getting the SE logo.
I was able to fix it with SEUS: plugged in the USB port while holding the Back key and the device turned on in Flash mode so I was able to flash it.
Hope it helps.
Click to expand...
Click to collapse
I have the same problem. First it wasn't working, then it was, and now it isn't again. I don't get a SE logo also. But when I plug in, I'm not able to turn on flash mode. It freezes, and SEUS says it can't repair my phone. What should I do?
freekh said:
I have the same problem. First it wasn't working, then it was, and now it isn't again. I don't get a SE logo also. But when I plug in, I'm not able to turn on flash mode. It freezes, and SEUS says it can't repair my phone. What should I do?
Click to expand...
Click to collapse
What procedure are you following to turn it on in flash mode?
What I did was that I plugged the USB cable while holding down the back button, there is no need to press any other button, it should automatically turn on.
burshturs said:
What procedure are you following to turn it on in flash mode?
What I did was that I plugged the USB cable while holding down the back button, there is no need to press any other button, it should automatically turn on.
Click to expand...
Click to collapse
That's what I did. I select factory reset in SEUS, it tells me to press the back button en plug in. I do so, it detect that I did, the little light on the phone turns green. SEUS begin repairing, but almost immediately says it is unable to repair.
I think it is because the phone freezes there. When I plug out, the light stays green, and all I can do is pull the battery out.
The same when I just try to turn the phone on. The light flashes, it vibrates ones (like it normally would) and then it stops and I cant do anything with it but pull out the battery.
you need to 1, pull the battery. 2, connect your phone via usb (still without battery). 3, open pc companion. 4, choose repair. 5, select x10 when asked phone model. 6, when asked to connect phone, put your battery in whilst holding the back button. 7, sit back, relax and your phone will be restored.
the reason your phone won't turn on/update/restore is due to a bootloop.
follow above steps and you x10 should always restore to factory...
I just think that the battery is too low and it can't live to finish the repair process
kemmo123 said:
you need to 1, pull the battery. 2, connect your phone via usb (still without battery). 3, open pc companion. 4, choose repair. 5, select x10 when asked phone model. 6, when asked to connect phone, put your battery in whilst holding the back button. 7, sit back, relax and your phone will be restored.
the reason your phone won't turn on/update/restore is due to a bootloop.
follow above steps and you x10 should always restore to factory...
Click to expand...
Click to collapse
Tried that now, but it doesn't work. The phone doesn't go into flash mode, and the pc doesn't find him. SEUS on the other hand does find him, but gives the same error.
silveraero said:
I just think that the battery is too low and it can't live to finish the repair process
Click to expand...
Click to collapse
That would really make sense, the only problem is that my phone doesn't charge when I put him in the loader. Or is there an other way to try to charge it?
kemmo123 said:
you need to 1, pull the battery. 2, connect your phone via usb (still without battery). 3, open pc companion. 4, choose repair. 5, select x10 when asked phone model. 6, when asked to connect phone, put your battery in whilst holding the back button. 7, sit back, relax and your phone will be restored.
the reason your phone won't turn on/update/restore is due to a bootloop.
follow above steps and you x10 should always restore to factory...
Click to expand...
Click to collapse
Tried again a few times, and now the phone goes into flash mode, and Pc Compagnion starts to repare, but gives an error after a while (the process bar shows zero progress, so I think the error is a time out error).
Other suggestions?
Thanks a lot for those many answers I will try all and then I tell you if it works !
Sent from my HTC Wildfire S A510e using XDA App
kemmo123 said:
you need to 1, pull the battery. 2, connect your phone via usb (still without battery). 3, open pc companion. 4, choose repair. 5, select x10 when asked phone model. 6, when asked to connect phone, put your battery in whilst holding the back button. 7, sit back, relax and your phone will be restored.
the reason your phone won't turn on/update/restore is due to a bootloop.
follow above steps and you x10 should always restore to factory...
Click to expand...
Click to collapse
tried it, finished the repair but still wont boot, waited for several hours then noticed red blinks, (didn't boot but drained my battery)
hey i triyed a few times in a row but it didnt help :S i do it exactly like feekh wrote it
my problem is that my x10i wont boot at all just vibrate no light nothing, and it wont charge olso but :
i can inter to flash mod and tried ((FlashTool)) its just stop instantly and show this ((Error flashing. Aborted))
any idea
m.tarek.s said:
my problem is that my x10i wont boot at all just vibrate no light nothing, and it wont charge olso but :
i can inter to flash mod and tried ((FlashTool)) its just stop instantly and show this ((Error flashing. Aborted))
any idea
Click to expand...
Click to collapse
Does it charge?, and have u tried SEUS or PC Companion?
Just say: Repair it.
no it dont charge
and SEUS not recognizing my phone
and PC Companion stops at downloading
Well considering it doesnt charge im not suprised flash tool/seus or pc companion doesnt work.if u cud some how charge the battery then u can investigate further
Sent from my X10i using XDA Premium App
i experienced the same issue last week...
now i recovered the phone.
First recharge the battery by wall charger. led will turn green instead of red... beware,,, insert battery after you plug in power cord.
second open the back cover, unscrew the screws, you can find the video from youtube to guide you... in my case, one of the connectors was not sitting well.
try it again... it will flash smoothly normally only takes 4 mins to done the whole processing... make sure you have full charged battery during the update.
i am recharging my battery with battery charger now
and i just finish unscrewing my phone and reconnecting all the connector and cleaning the USB and the battery connector
lets wait and see
fully recharged battery and all well connected connector and nothing
so tomorrow i will go for serves ????
I ended up buying an external Battery charger, works well.
I have the same problem here!
So today, I am trying to wake my x10 again one more time and I try to plug my old x10 to the wall plug and it's not even charging at all. No red blink. Then, I try to plug to my PC and the red blink turn on, taking forever to charge. I did charge this morning before I leave to school and when I came home, it's still doing the same thing again. I don't know how I can fix or turn it back on like I did before. Please help and the charging problem too.
i2nice said:
So today, I am trying to wake my x10 again one more time and I try to plug my old x10 to the wall plug and it's not even charging at all. No red blink. Then, I try to plug to my PC and the red blink turn on, taking forever to charge. I did charge this morning before I leave to school and when I came home, it's still doing the same thing again. I don't know how I can fix or turn it back on like I did before. Please help and the charging problem too.
Click to expand...
Click to collapse
Did you try to wipe battery stats in order for the phone to refresh the battery percentage again? Did you try a different wall plug?
mgsstar said:
Did you try to wipe battery stats in order for the phone to refresh the battery percentage again? Did you try a different wall plug?
Click to expand...
Click to collapse
Yes, I did try the different wall plug. Also, I can't turn it back to recovery to wipe the battery stats because it start to take very long time to charge.
Sent from my SGH-I747 using xda app-developers app
Hi sir, do you have time? I cant figure out what is wrong with my x10. When i try to flash those Generic Stock Rom, i get to have errors flashing. It aborts sometime when flashing system.sin and other sin depending on the tft file... i dunno what version my phone is but my pc detects it with flashmode. When im using Seus, it fails flashing in about 90% of the process... when booting my phone, just a quick vibrate with green flashes once. Do u have skype account? Hope u have time and can help me. Most of the links in xda our outdated. And i know my phone is outdated too. Thanks and more power