I get the message when i connect the x10 to the pc "usb device not recognized" i´ve tryed other cables and uninstalling the drivers and reinstalling them. Even anoher pc. but i get the same message where ever i try.
Is it possible that some of the pins are broken?
Is this something i can fixed on the warranty?
If so, even if i have installed a custom rom?
------
I turned the phone in and they replaced the SWAP-Unit. All on warenty! When i turned the phone in i asked the dude there about custom rom and repairs, he said it dident matter aslong as its something wrong with the hardware and not the software ofcaurse
Can u run the phone on flashtool or SEUS from SE on the computer? Or is the phone not reconized on that either?
Sent from XDA Premium from my X10a rooted running 2.2.1 CM Rom from Rendeiro2005
it says not recognized when i connect the phone to the pc even in flash mode, and the programs dont detect that its conneced.
leivz0r said:
it says not recognized when i connect the phone to the pc even in flash mode, and the programs dont detect that its conneced.
Click to expand...
Click to collapse
Then you propably got broken usb connector or your IC controler on motherboard stopped working. If you look at your connector and all the pins just looks fine then connector is really ok. Now, it is surely IC controller. You have to send your phone on warranty, and you are going to receive a new one. Yes, a new phone. There is no other way to fix this. And from what I know, you don't have to bother about different ROM installed. No one else bothers bout it too.
edit:
Oh BTW, if this happened now, then propably in short time you will loose ability to charge your phone VIA USB connetected to PC, if not immedietly then after this charging won't be possible at all, even with AC charger.... So... be prepared.
No my connections looked fine but on metering from the USB connector to the filtering circuit it was open circuit I flowed solder on the joint I then had continuity reassembled and all worked great, no need to go to the interface circuitary. I am saying if the system cannot read the voltage drop across the shunt resistor it cannot control the current and will not charge.
Sent from my X10i using XDA Premium App
+1, in my case it took about 2 weeks from pc unable to read phone to cannot charge at all.
diament said:
Then you propably got broken usb connector or your IC controler on motherboard stopped working. If you look at your connector and all the pins just looks fine then connector is really ok. Now, it is surely IC controller. You have to send your phone on warranty, and you are going to receive a new one. Yes, a new phone. There is no other way to fix this. And from what I know, you don't have to bother about different ROM installed. No one else bothers bout it too.
edit:
Oh BTW, if this happened now, then propably in short time you will loose ability to charge your phone VIA USB connetected to PC, if not immedietly then after this charging won't be possible at all, even with AC charger.... So... be prepared.
Click to expand...
Click to collapse
Sent from my X10i using XDA App
Since u guys are discussing this, I wanted to know how does one disconnect the phone from the the PC.what is mount and unmount?? Will it harm my device in anyway??? Which is the safest mode to connect it to PC??
first, try a different usb cable, I had the same problem. as for the mounting problem, should have made a new thread, but you should mount usb to transfer files, but no need to if just charging, but be sure to unmount or else you could corrupt your sd card, and it also creates another drive on your computer if you don't 'safely remove usb' after unmounting
Sent from my X10 using XDA Premium App
denenatse said:
first, try a different usb cable, I had the same problem. as for the mounting problem, should have made a new thread, but you should mount usb to transfer files, but no need to if just charging, but be sure to unmount or else you could corrupt your sd card, and it also creates another drive on your computer if you don't 'safely remove usb' after unmounting
Sent from my X10 using XDA Premium App
Click to expand...
Click to collapse
m sorry didn't want to make a new thread so I asked my question here...am sorry..but where is the unmount option..on the comp or on the PC??
circleofomega said:
m sorry didn't want to make a new thread so I asked my question here...am sorry..but where is the unmount option..on the comp or on the PC??
Click to expand...
Click to collapse
on your phone - settings--}SD card and phone storage--}unmount SD card
circleofomega said:
m sorry didn't want to make a new thread so I asked my question here...am sorry..but where is the unmount option..on the comp or on the PC??
Click to expand...
Click to collapse
no no, its the one in the notification bar.
Sent from my X10 using XDA Premium App
Related
Stuck at Vibrant screen. Cant geet in bootloader or recovery. I have odin, have the .pit and everything but when I go into download mode, Odin nor my computer will recognize the phone... Please help. Thanks!
pull the battery 1st and then replace back in then hold the lower volume key down along with the on button try that or get a jig
U need samsung drivers
Sent from my SGH-T959 using XDA App
Depending on what your friend was running, yes, you need to install the drivers so that when you connect your pc recognizes it. It's not bricked, no worries... keep calm.
I made a post with the drivers, but you would likely find it faster with a quick google search.
sell it for parts on Ebay
Sent from my SAMSUNG-SGH-I997 using Tapatalk
re-install driver, change usb cable, etc...
What I've found is that 9/10 its the USB cable when the computer doesn't recognize the device. I'd check it first. Now a better question is what did you do to your friends phone to brick it with out it being plugged to the computer in the first place?
Sent From A Darky place.....10.2
o0stryxs0o said:
What I've found is that 9/10 its the USB cable when the computer doesn't recognize the device. I'd check it first. Now a better question is what did you do to your friends phone to brick it with out it being plugged to the computer in the first place?
Sent From A Darky place.....10.2
Click to expand...
Click to collapse
in addition to what you said, sometimes, pluggin it in a different usb works too.
Agreed!
The damn cables suck! Almost 1/2 need to be replaced eventually, and it makes you question the integrity of the device itself. They should make better cables or provide you with 2 when you purchase the phone.
Hey Guys!
I have a suspect problem with my Atrix. I dont get an USB connection to my PC (Win7 64bit) or to my laptop (Win7 32bit).
So when I connect the USB cable, I get the message "USB connection" in the status bar, but only for 1-2 seconds and than its gone.
Sometimes (rarely) it works when I press fast on this message (but it can be only luck).
But I flashed today a new ROM (AURA) and with fastboot I havent had any problems.
The drivers are installed on my PC and with this PC it worked at beginning (some month ago).
I have tried:
-different-ROM flashed (aura, Vodafone 2.3.4)
-Debuggin-on / off
-2 Different USB cable
Can it be a hardware problem? But I wonder why I have no problems with fastboot (charging via USB also works of course!)...
After the flash I try to root with Oneclickroot-package, but the programm cant find my atrix.
Someone else has an idea or maybe the same problem with fix?
EDIT: Have somebody experience with the motorola warranty support? Have somebody problems with warranty (not only motorola) beacause of custom ROM or something..?
TT-DD said:
Hey Guys!
I have a suspect problem with my Atrix. I dont get an USB connection to my PC (Win7 64bit) or to my laptop (Win7 32bit).
So when I connect the USB cable, I get the message "USB connection" in the status bar, but only for 1-2 seconds and than its gone.
Sometimes (rarely) it works when I press fast on this message (but it can be only luck).
But I flashed today a new ROM (AURA) and with fastboot I havent had any problems.
The drivers are installed on my PC and with this PC it worked at beginning (some month ago).
I have tried:
-different-ROM flashed (aura, Vodafone 2.3.4)
-Debuggin-on / off
-2 Different USB cable
Can it be a hardware problem? But I wonder why I have no problems with fastboot (charging via USB also works of course!)...
After the flash I try to root with Oneclickroot-package, but the programm cant find my atrix.
Someone else has an idea or maybe the same problem with fix?
EDIT: Have somebody experience with the motorola warranty support? Have somebody problems with warranty (not only motorola) beacause of custom ROM or something..?
Click to expand...
Click to collapse
my first atrix was replaced free (i was inside of the first 30 days) the second one my screen cracked and i did have warrenty however it would cost 140 +shipping so i just bought a new one for 99 lol and am planing to crack open the 2nd atrix and try to replace rhe screen
cause u can buy a new screen for like 40-60 bucks
then i plan to sell it on craigslist
dont think that answers your question
however if they can determine if its "hardware" related and not due to abuse and "normal use they prolly just extchange it
and yes all three of my atrixes were /are rooted and unlocked
Sent from my MB860 using Tapatalk
This may sound silly but my atrix really does not like the USB ports on the front of my case
Have you tryed a different USB port
You have made sure that the usb mode is not "none" right? Because otherwise it will charge like normal and fastboot will work because that is pre OS but it won't transfer data when the phone is on.
oddbubble said:
This may sound silly but my atrix really does not like the USB ports on the front of my case
Have you tryed a different USB port
Click to expand...
Click to collapse
Ya, I know this with some other phones or equipment. I test it, but no change.
bonez565 said:
You have made sure that the usb mode is not "none" right? Because otherwise it will charge like normal and fastboot will work because that is pre OS but it won't transfer data when the phone is on.
Click to expand...
Click to collapse
Can you my how? I think this selection come when the USB cable get connected?!
If I connect the cable to my phone, I get shortly the message "USB Connection - Mass storage" (sry, I dont know the true message in english)
TT-DD said:
Ya, I know this with some other phones or equipment. I test it, but no change.
Can you my how? I think this selection come when the USB cable get connected?!
If I connect the cable to my phone, I get shortly the message "USB Connection - Mass storage" (sry, I dont know the true message in english)
Click to expand...
Click to collapse
I have problems if I move my phone while plugged in. Have you tried setting it on a table and plugging in and making sure not to move it?
rquinn19 said:
I have problems if I move my phone while plugged in. Have you tried setting it on a table and plugging in and making sure not to move it?
Click to expand...
Click to collapse
Of course! Now I tested if I get connection with MSU or RSD to my phone. But no... nothing. DAMN!
EDIT: RSD works! Now I think it gets more and more suspekt.
EDIT2: I tested it in the cardock. But it dont goes to the "carmodus", loading only!
If its under warranty, warranty it out. I'm on my 3rd atrix in 11 months. Faulty digitizers...
erick161 said:
If its under warranty, warranty it out. I'm on my 3rd atrix in 11 months. Faulty digitizers...
Click to expand...
Click to collapse
Seeing how the Atrix is less than a year old I don't understand why we can't just walk into the store and get warranty work as long as it's not something done by the user of course. They know if it's one of their phones they sold by the imei. What difference does it make if I bought it 2nd hand?
Just ranting...
So, the problem was a defect mainboard. I sent it back to motorola and now it works again. Thx for help!
Close//
Gesendet von meinem MB860 mit Tapatalk
I have a stock Amaze which I bought used. It charges fine through the USB but I can not mount it to my PC.
The PC does not acknowledge the phone at all and the phone does not acknowledge the PC at all, It just begins charging. I asked the previous owner, but he says that he always used a card reader and never tried accessing the phone through the USB port.
Has anyone run into this?
d73805 said:
I have a stock Amaze which I bought used. It charges fine through the USB but I can not mount it to my PC.
The PC does not acknowledge the phone at all and the phone does not acknowledge the PC at all, It just begins charging. I asked the previous owner, but he says that he always used a card reader and never tried accessing the phone through the USB port.
Has anyone run into this?
Click to expand...
Click to collapse
have you tried all of your usb ports.. and also maybe checking to see if you have the htc usb drivers installed.. or if they are upto date.. and about uninstalling all of your usb drivers.. restarting your pc and trying again... or checking if the phone can mount to another computer just to make sure its not your computer..?
Ninjistix said:
have you tried all of your usb ports.. and also maybe checking to see if you have the htc usb drivers installed.. or if they are upto date.. and about uninstalling all of your usb drivers.. restarting your pc and trying again... or checking if the phone can mount to another computer just to make sure its not your computer..?
Click to expand...
Click to collapse
I've tried multiple computers and multiple cables including 2 OE HTC cables with the odd end. I've restarted the PCs and the phone. I tried with USB de-bugging both checked and unchecked. I haven't updated any drivers but I did install HTC Sync on one of the computers. I would think that even without the proper drivers, I would at least get an error message but I get nothing.
you need to install the htc usb drivers for the phone to be recognized by your computer.. open device manager and go to usb settings.. plug your phone it to see if it registers on the device manager.. after you installed the htc usb drivers (you don't need htc sync thats for updating and backing up sense)... if anything you can try to factory reset your phone..
Ninjistix said:
you need to install the htc usb drivers for the phone to be recognized by your computer.. open device manager and go to usb settings.. plug your phone it to see if it registers on the device manager.. after you installed the htc usb drivers (you don't need htc sync thats for updating and backing up sense)... if anything you can try to factory reset your phone..
Click to expand...
Click to collapse
I installed installed a driver package that that was named "HTCDriver3.0.0.007". Nothing registers in the device manager when I plug the phone in. I'll try a factory reset tonite and see what happens.
Also, I sent a message to HTC support this morning, but I didn't get a response yet.
Thanks for the help so far. If anybody's got any more ideas or experience with this, I'd love to hear.
dose your computer make any sounds when you connect the phone to it? and where did you get those drivers from? you might want to uninstall them and install the ones that come with hasoon's AIO toolkit.. or get them directly from the htc website
Ninjistix said:
dose your computer make any sounds when you connect the phone to it? and where did you get those drivers from? you might want to uninstall them and install the ones that come with hasoon's AIO toolkit.. or get them directly from the htc website
Click to expand...
Click to collapse
That driver actually did come from hasoon. The only thing available from the HTC site was Sync and a tethering driver, which I tried both.
when you install and uninstall drivers from the computer normally your suppose to restart the computer and the device.. and dose your computer make a sound when you plug your phone in? and does the charging light on the phone come on?
Ninjistix said:
when you install and uninstall drivers from the computer normally your suppose to restart the computer and the device.. and dose your computer make a sound when you plug your phone in? and does the charging light on the phone come on?
Click to expand...
Click to collapse
There's no sound from the PC or phone, but the charging light does come on.
if the light comes on the device is connecting to the computer.. if there's no sound the device isn't being recognized by what your plugin it into.. there could be one issue with the usb drivers on the computer and or something wrong with the usb port of the phone.. do you have another phone to connect it to the same cable.. using the same usb port on the pc to see if that phone gets recognized by the computer...? if it does then there's a problem with your phones usb port.. if it doesnt then it might be the cable or the usb port.. do the following un-install all of your usb drivers.. even the htc one.. restart your computer in safe mode with networking and then re-install the drivers and then plug in the phone to test it.. or you can boot the phone into bootloader by removing the battery from the phone then re-inserting it and power on the phone by holding volume down and power till the phone boots up.. go to fastboot and see if the phone recognizes the usb from there...
i still think the main issue here is driver related though.. maybe you have a virus on your computer messing with the drivers or firewall or antivirus or something.. but try the safemode with networking first before anything else...
Ninjistix said:
if the light comes on the device is connecting to the computer.. if there's no sound the device isn't being recognized by what your plugin it into.. there could be one issue with the usb drivers on the computer and or something wrong with the usb port of the phone.. do you have another phone to connect it to the same cable.. using the same usb port on the pc to see if that phone gets recognized by the computer...? if it does then there's a problem with your phones usb port.. if it doesnt then it might be the cable or the usb port.. do the following un-install all of your usb drivers.. even the htc one.. restart your computer in safe mode with networking and then re-install the drivers and then plug in the phone to test it.. or you can boot the phone into bootloader by removing the battery from the phone then re-inserting it and power on the phone by holding volume down and power till the phone boots up.. go to fastboot and see if the phone recognizes the usb from there...
i still think the main issue here is driver related though.. maybe you have a virus on your computer messing with the drivers or firewall or antivirus or something.. but try the safemode with networking first before anything else...
Click to expand...
Click to collapse
No luck with safe mode. I just ordered a new OE USB cable. It's hard to believe that I have 2 bad cables, but it was cheap enough. I may try the reset also.
d73805 said:
That driver actually did come from hasoon. The only thing available from the HTC site was Sync and a tethering driver, which I tried both.
Click to expand...
Click to collapse
Unfortunately to me it sounds like a messed up usb port in your phone. I have a moto defy that got water in the USB port and same problem now. It charges, but is not recognized by the computer in any way. No matter what computer, drivers installed or not, my amaze is always recognized somehow, when I plug it into a computer.
Sent from my HTC_Amaze_4G using xda app-developers app
masondoctorjt said:
Unfortunately to me it sounds like a messed up usb port in your phone. I have a moto defy that got water in the USB port and same problem now. It charges, but is not recognized by the computer in any way. No matter what computer, drivers installed or not, my amaze is always recognized somehow, when I plug it into a computer.
Sent from my HTC_Amaze_4G using xda app-developers app
Click to expand...
Click to collapse
You're probably right. I would think that if it were connecting I would get some sort of message from either the phone or the PC.
d73805 said:
You're probably right. I would think that if it were connecting I would get some sort of message from either the phone or the PC.
Click to expand...
Click to collapse
If anyone cares to know, I got a response from HTC. They had me do some tests which I had already done (different cables, different ports, reset the phone), which of course didn't work. They told me to call the service center. The girl I talked to seemed reasonably knowledgeable. She told me that it's very unusual for the port to be bad in such a way that it charges but won't pass data, but that it was not impossible. She checked the serial number and told me that I was on my last day of warranty and if I shipped it that day it would be covered, assuming there is no damage due to owner misuse. So I sent it in.
Assuming they can and do fix it, I'm not sure if they will give me any details as to what was wrong, but I will let everyone know what happened. I saw a few instances online of people having the same issues as me with HTC phones but no one ever seemed to have any solutions.
i'm not shocked that htc wasn't able to help... 75% of the time the people working tech support don't know anything they always read "steps" to fix certain problems from their database... **** i learned so much about computer's from google its not even funny... i don't call tech support unless "google" cant find a solution.. lol
Ninjistix said:
i'm not shocked that htc wasn't able to help... 75% of the time the people working tech support don't know anything they always read "steps" to fix certain problems from their database... **** i learned so much about computer's from google its not even funny... i don't call tech support unless "google" cant find a solution.. lol
Click to expand...
Click to collapse
My Amaze has been fixed under warranty and will supposedly be here tomorrow. I doubt HTC will tell me what the problem was, or whether it was a hardware or software issue.
Thanks for all the help. You'll be hearing from me.
Hello to all. Suddenly my galaxy s3 usb cable stopped working. Whenever i connect to pc it starts charging but display message of pc taskbar that (USB device not recognized, The last USB device you connected to this comnputer malfunctioned, and windows does not recognize it.) Even i tried to connect another nokia mobile to pc with SGS3 same cable & worked fine but mine not working. Even i try other ports too as well as back side of main board & tried another cable but the problem is still same. Please kind person help me to solve problem. Thanx
Sometimes the cable has a problem with the phone. Mine stopped working for some weeks, then it was normal again. Just use another cable.
Please post in the Q&A section next time.
Sent from my GT-I9300 using xda app-developers app
kofiaa said:
Sometimes the cable has a problem with the phone. Mine stopped working for some weeks, then it was normal again. Just use another cable.
Please post in the Q&A section next time.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Thanx for reply. You told that sometime the usb cable has a problem with the phone but the same cable working fine with another device as i mentioned already above problem.
That's what I encountered, the cable worked with other devices. Try another cable and give feedback.
Sent from my GT-I9300 using xda app-developers app
Replace the cable, mate.
I have 3 Sgs3's, of which:
1st cable was eaten by cat,
2nd causes: connected-disonnected messages in Odin
3rd one works flawless...
Wrong section, post in QA
spamtrash said:
Replace the cable, mate.
I have 3 Sgs3's, of which:
1st cable was eaten by cat,
2nd causes: connected-disonnected messages in Odin
3rd one works flawless...
Click to expand...
Click to collapse
already replaced the cable but still same problem
kofiaa said:
That's what I encountered, the cable worked with other devices. Try another cable and give feedback.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
same day i had try another cable but did not worked... This cable works fine when i tried on another pc.
It shows Unkown Device in Device manager. I'm using windows 8 & Windows 7. Tried everything, installed kies,samsung usb drivers, windows drivers but still shows Unkown Driver. I;m using XXELLA latest firmware in my device, Is that XXELLA problem? Please help me.
Try to clean the USB connector of your phone with a toothpick (carefully), I had this kind of problem and cleaning the connector worked fine for me
Sent from my GT-I9300 using xda app-developers app
ptisam said:
Try to clean the USB connector of your phone with a toothpick (carefully), I had this kind of problem and cleaning the connector worked fine for me
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
i did as much i know but did not work
ptisam said:
Try to clean the USB connector of your phone with a toothpick (carefully), I had this kind of problem and cleaning the connector worked fine for me
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
I did again to clean connector with needle & works very well as works before. Thanx very much. Thanx to all who had reply to this thread. Problem solved.
mrjoy said:
I did again to clean connector with needle & works very well as works before. Thanx very much. Thanx to all who had reply to this thread. Problem solved.
Click to expand...
Click to collapse
Many thanx for this
I just had exactly the same problem tried everything clearing cache, different cables, restarting Phone, removing battery & sim, I was on the verge of doing a factory reset but realised that if it had no effect I would not be able to access my backup,
5 minutes with a needle torch and magnifying glass removed a lot of fluff (why didnt Samsung put one of those flap thingys over it)
Now works perfectly again,
hello i am haveing same problem i have 3 samsung galaxy s3 only one is not connecting to pc its charging only i have tried every solution on google as well as xda developers .... is their any kind of problem with my usb connector ???? will it resolve by cleaning or i have to change it ????
i have tried by changing cable hard reset secret codes every thing but had no luck i need help here plzzzzzzzzzz......
I think this will work.
I think one of this options will work:
-option 1:
Type *#7284# in your phones keypad. Then you choose qualcomm settings. Select MTP + ADB and then reboot.
-option 2:
Type *#0808# in your phones keypad. Select MTP + ADB and then reboot.
Same issue here
Hello I and many others have same issues after the 4.3 upgrade, theres quite many threads about it on the net but still no solution. I have contacted Samsung Sweden about this issue but they do not knwo of any widespread problem and said to send the phone to service (not optional for me since i change the screen of mine + out of warranty). Asked if there is any bugfix update on the way, but Samsung support didnt know about it
I have tried 3 computers and 6 usb cords, cleanded the connectors but no luck. In my case the phone never realizes that its connected to a computer, but starts to charges instead. Some people says that after the upgrade the computer sees it as an unknowned device.
EDIT: Didnt see this thread was solved, nothing to see here, will continue to look for a solution
i have a sgs3 i9300. i recently flashed the stock MJ9 android 4.3 firmware to it and it was working fine till 3 days ago when it started to show driving mode sign and then i flashed the rom again 2 or 3 times i wiped user data and now the driving mode sign is gone but i cannot connect the phone to the computer, when i connect it nothing happens, on mobile or computer. nothing. (no usb charging or mass storage or any sounds or anything) however i can charge it using usb charger that came with it and strangely i can even use the phone in download mode with computer to flash it using odin. i read somewhere that its not a hardware issue so im really looking forward to some help here. thanks
Many similar threads, lots of possible reasons. Best search for the most likely causes, which will include your pc, leads, phone hardware etc.
Sent from my GT-I9300 using Tapatalk
boomboomer said:
Many similar threads, lots of possible reasons. Best search for the most likely causes, which will include your pc, leads, phone hardware etc.
Sent from my GT-I9300 using Tapatalk
Click to expand...
Click to collapse
tested it on different computer still the same. phone hardware should not be the issue since i am able to use it in download mode and charge it using the charger. so hardware port cannot be the problem.
codetoeternity said:
tested it on different computer still the same. phone hardware should not be the issue since i am able to use it in download mode and charge it using the charger. so hardware port cannot be the problem.
Click to expand...
Click to collapse
Search = the cable
JJEgan said:
Search = the cable
Click to expand...
Click to collapse
changed the cable. still the same. i saw another post about the same issue (quite old though and had no replies) and he was talking about some code like *#7280# (or similar code that opens up a hidden menu that allows to do something to fix it) but i opened that menu and those options werent there.
searched all over xda. tried all the things suggested (including the recovery firmware). still things remain the same. i still can flash it in download mode. but i cant charge it or anything. im sure its a software problem not a hardware problem. some serious help is required here
codetoeternity said:
searched all over xda. tried all the things suggested (including the recovery firmware). still things remain the same. i still can flash it in download mode. but i cant charge it or anything. im sure its a software problem not a hardware problem. some serious help is required here
Click to expand...
Click to collapse
Would suggest you uninstall Kies if you have it then download the new version (Kies for non Android 4.3 or Kies 3 for Android 4.3) from here Kies this will re-install the new drivers, re-boot your PC then plug your phone into your PC and you should get the message installing drivers.
Don't let Kies run at the same time as Odin otherwise it wont work but I guess you probably know that.
ag4751 said:
Would suggest you uninstall Kies if you have it then download the new version (Kies for non Android 4.3 or Kies 3 for Android 4.3) from here Kies this will re-install the new drivers, re-boot your PC then plug your phone into your PC and you should get the message installing drivers.
Don't let Kies run at the same time as Odin otherwise it wont work but I guess you probably know that.
Click to expand...
Click to collapse
done. still no use. since the device isnt even noticed by the computer. its like nothing is attached. however in download mode i get a lot of devices in device manager. im unable to charge my phone or connect as mtp thats the problem. i dont think the port is faulty coz the download mode works just fine.
USB port on the phone faulty or motherboard .
JJEgan said:
USB port on the phone faulty or motherboard .
Click to expand...
Click to collapse
in that case the phone shudnt work in download mode. i think.
codetoeternity said:
in that case the phone shudnt work in download mode. i think.
Click to expand...
Click to collapse
Have you tried different USB ports on the PC, there have been reports before that for some reason the port people normally use stops working and by switching to another USB port it works
Forgot to say if not already tried, turn off the phone pull the battery leave for a minute or two, replace the battery and reboot then try to connect it.
ag4751 said:
Have you tried different USB ports on the PC, there have been reports before that for some reason the port people normally use stops working and by switching to another USB port it works
Forgot to say if not already tried, turn off the phone pull the battery leave for a minute or two, replace the battery and reboot then try to connect it.
Click to expand...
Click to collapse
have tried different ports and different computers different cables etc and the battery was out all day still no use
codetoeternity said:
have tried different ports and different computers different cables etc and the battery was out all day still no use
Click to expand...
Click to collapse
Not having much luck are you, one last thing I have read before is using a pin or cocktail stick (you may need a magnifying glass as well) to gently clean the USB port on the phone and the cable, remove the battery first, but be careful you don't actually damage anything, that's why you need to be gentle with it.
Can you flash via ODIN successfully but phone not recognised by Windows??? Sounds like not all pins connecting properly. Clean connector VERY carefully...
Sent from my GT-I9300 using Tapatalk
ag4751 said:
Not having much luck are you, one last thing I have read before is using a pin or cocktail stick (you may need a magnifying glass as well) to gently clean the USB port on the phone and the cable, remove the battery first, but be careful you don't actually damage anything, that's why you need to be gentle with it.
Click to expand...
Click to collapse
i used a very sharp pin to clean the port on phone. did clean a bit, and had a bit of success. i cud charge my phone with the connector connected at a certain angle. if i wud touch it it would stop charging. but that went on for like 40 minutes and then it stopped working any ideas on how can i clean it? if i open the phone will i be able to clean it easily?
codetoeternity said:
i used a very sharp pin to clean the port on phone. did clean a bit, and had a bit of success. i cud charge my phone with the connector connected at a certain angle. if i wud touch it it would stop charging. but that went on for like 40 minutes and then it stopped working any ideas on how can i clean it? if i open the phone will i be able to clean it easily?
Click to expand...
Click to collapse
Never actually had to do it, only read what others have done, maybe an old dry toothbrush would do it as ling as you remember the gentle bit, if the pin did help then this could solve the problem for you it may simply be dust or dirt on the connections.
Would do both the phone and the cable end, not easy but worth a try as its free.