As you can see in the picture, there are two identical antennas on opposite sides of the phone. The one to the right is the GPS antenna. After applying solder to it, my GPS has been craaaazy fast and accurate.
Question: what's the antenna on the left side? Is it the antenna for making calls? Would applying solder to it improve my reception?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Related
What is the round hole at the back of the Xperia Go?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
For anyone who still cares...
It connects to a syringe through this adapter, a pipe, and a 3-way valve.
After blocking both mics with strong tape, you pump air into the phone while using the "water resistance" test in the service app to find out if the case has leaks.
i'm trying to fix an alps 5i phone. After i found the wright firmware, the phone never get signal. Trying to get a solution, found that the network antenna, is unwelding. It's very dificult to weld the antena, as the piece that is unwelded, is the motherboard jack. Is any solution that avoid welding the jack to the motherboard? upload a photo.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
hi ,
I want to replace the main antenna- the cellular antenna (not the gps or the wifi) but im confused in what shes looks like .
can someone show me a picture of it or a lnk to ebay in which to buy it ?
thnx a lot
There are 10 screws behind the phone. 9 is for the back cover and one is for the main antenna which is over the speaker. The part that comes out with the speaker is the main antenna...
can you show me a picture of it?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Here it is
Hello XDA,
I want to wire a battery circuit to a cell, but the circuit has no indication which side is positive which side is negative.
The circuit is from an iPhone 4s.
note: on the circuit there is a tiny "1" and "2" next to the respective pins.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks!
there is low range of wifi after the screen replacment donnot knw what happened
Look at that arrow cable, that it is well connected up and down, there are two holes at the top, if you made a mistake. The bottom circle is the antenna module, it has some metal plates that make contact and if they do not do it well, you have to raise them a little.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}