So after an incident saturday, my Thunderbolt screen is in a trillion pieces. The phone still boots up fine, receives text messages (much to my chagrin) and receives calls. In fact, it's still paired with my bluetooth in my car so I can make and receive calls when in my vehicle.
However, my replacement should be here tomorrow. I missed several important text messages (the source of its destruction).
Unfortunately, I did not have the phone in PC Mode prior to its destruction, so I cannot see it with adb devices. Is there a way to get it into PC Mode without seeing the screen? As in, a certain key press on bootup that would allow the PC to see it properly?
Upon that, I could use ddms to capture the screen, or download the text database (it is rooted).
On the other hand, the Verizon tech at the corporate store says they can transfer texts as well as contacts (I have Exchange so that's not an issue) if the phone boots. I am very skeptical that this is the case, but she insisted. If they can, then this isn't a big issue to me.
Thanks!
I *think* I might have solved part of the problem.
This is a new PC and I never installed the HTC drivers.
Before I installed them, nothing showed up in adb devices.
Now, my device is listed... but it says "offline" or "error: device offline" when trying to use adb shell.
ddms also doesn't allow me to get a screen shot.
Did you not have USB Debugging checked? That's all you need for ADB to work. It doesn't have to be in PC mode if that's checked.
I'm positive I did have USB Debugging checked as I rooted the phone and did a lot of hacking. Good to know I don't have to put it in PC mode though.
However, I can't seem to get by the "offline" message I get with adb devices or "error: device offline" when I do an adb shell. doing a kill-server and start-server has no effect.
I think I might be on the right track.
I was able to boot into recovery somehow by using power and vol down.
Then I hit something (Power I think) and it vibrated.
Now adb devices lists my device, followed by recovery.
I can connect via adb and list the directory, but only the recovery partition is mounted.
I was able to mount the system via mount -t ext3 /dev/block/mmcblk0p25 /system, but I don't know what the mmcblk is for the data partition.
GOT IT!
Using ddms, I was able to see that I had booted into Clockwork. I then was able to navigate to the mount section and mount /data.
From there, I was able to use adb pull to get the mmssms.db file and use Root Explorer on my Xoom to view those text messages. Then I was able to see why I threw my phone in the first place
Phew, it's amazing what you can do in the Android world.
Bodero said:
Then I was able to see why I threw my phone in the first place
Phew, it's amazing what you can do in the Android world.
Click to expand...
Click to collapse
lol funniest thing i heard all day... maybe there is an android app to fix those anger issues!!
Related
So I just installed Ubuntu 10.10 on my PC and I'm really digging it. But when I try to mount my sdcard from the phone, it doesn't show up under my places menu. I'm running GSB 1.8.1. I don't have a problem mounting it under windows XP, and also have no problem using the wired tether function. Is there anything I can change on the phone or in Ubuntu to fix this?
I am running Ubuntu 10.04 LTS - inside a Virtual Machine - and I can mount the drive from inside the VM. (Believe me, that's even trickier than what you are trying).
But, 10.10 might have had some changes, and I wouldn't be surprised if your result depended on which desktop you are running; so maybe you need to mount the thing manually.
Try this:
With the phone unplugged, type
$ sudo /bin/bash
# tail -f /var/log/messages
This will continue to show you various kernel messages as they appear. Next, plug in the phone.
Hopefully, you will see some lines scroll by that mention USB.
Next, mount the SD to the PC from the phone. If all goes well, you should now see some mention of "SCSI" devices /dev/sdX, where X is probably "a", "b" "c" "d". Probably you will also see mention of the first partition on the device, such as "/dev/sdb1". Make a note of this drive device name.
Cancel the "tail" command (Ctrl-C) and do a
# mount | grep sdb1
( note device name "sdb1" ; use whatever you saw previously )
This will show you if the device is already mounted somewhere.
If the device has not been mounted, you can manually mount it, as in:
# mkdir -p /mnt/Eris_SD
# mount -o rw /dev/sdb1 /mnt/Eris_SD
( Again, note device name "sdb1" - use whatever you saw previously. If it doesn't recognize the file system, use "mount -o rw -t vfat /dev/sdb1 /mnt/Eris_SD" )
Hopefully that will do it. Don't forget to "umount /mnt/Eris_SD" when you are done.
If the device never shows up in the /var/log/messages file, then you have some other problems.
If you don't see anything in the log file indicating USB activity, well - you ought to investigate what is going on at the USB port.
Right now my phone is booted into Amon_RA; if I issue the "lsusb" command, I see:
Code:
Bus 001 Device 031: ID 0bb4:0c98 High Tech Computer Corp.
BTW, on my VM, it seems like I need to unplug the USB cable after I dismount the drive, or the next time I export the SD card to the PC, the kernel recognizes it, but the automounter doesn't automatically mount it.
Another thing that you might try to make things more automatic is the instructions in "Step #5" of this XDA post. This is meant for allowing an unprivileged user on your Ubuntu box to use ADB or fastboot without needing to "sudo" to root. I did this on my VM - I don't think that's the reason that the phone automounts into the SD drive, but perhaps it is related - the same "Vendor_ID" is in use when the phone is in "Composite ADB mode".
When you get to the part in these instructions about restarting the "udev" subsystem, unplug your USB cable first - and then see what you get when you plug it in and fire up the SD export from the phone.
hope that helps.
bftb0 said:
BTW, on my VM, it seems like I need to unplug the USB cable after I dismount the drive, or the next time I export the SD card to the PC, the kernel recognizes it, but the automounter doesn't automatically mount it.
Click to expand...
Click to collapse
I noticed this on my desktop with a full install of Ubuntu. I knew it was connected because the charge led was lit, but I would have to unplug the usb and plug it back in almost every time just to get it to mount or connect to the internet with wired tether. I never messed with it BUT it did seem to fix itself once I started doing the system updates on Ubuntu.
bftb0 said:
$ sudo /bin/bash
# tail -f /var/log/messages
This will continue to show you various kernel messages as they appear. Next, plug in the phone.
Hopefully, you will see some lines scroll by that mention USB.
Next, mount the SD to the PC from the phone. If all goes well, you should now see some mention of "SCSI" devices /dev/sdX, where X is probably "a", "b" "c" "d". Probably you will also see mention of the first partition on the device, such as "/dev/sdb1". Make a note of this drive device name.
Click to expand...
Click to collapse
When I got to this step, the log didn't show anything when I mounted the sdcard from the phone. On a whim I tried rebooting the phone into the recovery (AmonRA 1.6.2) and then the log showed it as /sdc. If I turn on USB Mass Storage from the recovery, Ubuntu recognizes it then. On a side note, I'd been having trouble getting ADB to recognize my phone until I did this. But shouldn't this also work with the phone fully booted? Maybe it's GSB?
EDIT: I flashed the Stock Sense 2.1 rom to see if everything worked and it did. I rerooted and restored a backup I made this morning to GSB, and Ubuntu recognizes my sdcard when I mount it, and ADB now works. Thanks for your help.
prsguitaruser said:
When I got to this step, the log didn't show anything when I mounted the sdcard from the phone. On a whim I tried rebooting the phone into the recovery (AmonRA 1.6.2) and then the log showed it as /sdc. If I turn on USB Mass Storage from the recovery, Ubuntu recognizes it then. On a side note, I'd been having trouble getting ADB to recognize my phone until I did this. But shouldn't this also work with the phone fully booted? Maybe it's GSB?
EDIT: I flashed the Stock Sense 2.1 rom to see if everything worked and it did. I rerooted and restored a backup I made this morning to GSB, and Ubuntu recognizes my sdcard when I mount it, and ADB now works. Thanks for your help.
Click to expand...
Click to collapse
In case this helps, GSB mounts the SD card through USB just fine with Windows. Don't take my comment as a Windows versus Ubuntu, thing, however. Just for whatever it's worth.
prsguitaruser said:
I flashed the Stock Sense 2.1 rom to see if everything worked and it did. I rerooted and restored a backup I made this morning to GSB, and Ubuntu recognizes my sdcard when I mount it, and ADB now works. Thanks for your help.
Click to expand...
Click to collapse
Glad to here you got this fixed
prsguitaruser said:
When I got to this step, the log didn't show anything when I mounted the sdcard from the phone. On a whim I tried rebooting the phone into the recovery (AmonRA 1.6.2) and then the log showed it as /sdc. If I turn on USB Mass Storage from the recovery, Ubuntu recognizes it then. On a side note, I'd been having trouble getting ADB to recognize my phone until I did this. But shouldn't this also work with the phone fully booted? Maybe it's GSB?
EDIT: I flashed the Stock Sense 2.1 rom to see if everything worked and it did. I rerooted and restored a backup I made this morning to GSB, and Ubuntu recognizes my sdcard when I mount it, and ADB now works. Thanks for your help.
Click to expand...
Click to collapse
Great news! I don't know how I missed your edit since I quoted it in my last response. I must've had this thread open in my browser from before, and went to respond to it after your edit.
OK, so I went back to GSB and had the problem again. I found out that ADB works and the sdcard mounts until I turn on wired tether, then if I turn wired tethering off, my sdcard still won't mount, nor will ADB recognize my phone, until I reboot the phone. Every time I've tried to mount the sdcard, I've made sure to turn tethering off. But it seems like tethering is what kills it.
prsguitaruser said:
OK, so I went back to GSB and had the problem again. I found out that ADB works and the sdcard mounts until I turn on wired tether, then if I turn wired tethering off, my sdcard still won't mount, nor will ADB recognize my phone, until I reboot the phone. Every time I've tried to mount the sdcard, I've made sure to turn tethering off. But it seems like tethering is what kills it.
Click to expand...
Click to collapse
Are you using the tethering abilities built into CM7 (for wired you have to use the Tether Widget from the market, but that's it), or are you using the "for root" apps? IMHO, the "for root" apps are redundant and don't work as well as the native tethering in CM6 and CM7.
roirraW "edor" ehT said:
IMHO, the "for root" apps are redundant and don't work as well as the native tethering in CM6 and CM7.
Click to expand...
Click to collapse
Really? Because I have never been able to get "native" tethering to work. They appear to be working but there not allowing data to pass through.
Also I only use the ones posted on Google's source page.
I believe there may be an issue here that isn't faulted by the phone or the tethering apps. I think it has something to do with the way Ubuntu reacts to the change between allowing data inbound and when it goes back to remounting the phone and its SD card. Honestly if you can I would say allow your Ubuntu to do its system updates then see what happens.
@ roirraW "edor" ehT, no harm intended at the top of my post. Just my personal observation of how these things generally work out for me. Heh.
Powered by: GSB CM7
wildstang83 said:
Really? Because I have never been able to get "native" tethering to work. They appear to be working but there not allowing data to pass through.
Also I only use the ones posted on Google's source page.
I believe there may be an issue here that isn't faulted by the phone or the tethering apps. I think it has something to do with the way Ubuntu reacts to the change between allowing data inbound and when it goes back to remounting the phone and its SD card. Honestly if you can I would say allow your Ubuntu to do its system updates then see what happens.
@ roirraW "edor" ehT, no harm intended at the top of my post. Just my personal observation of how these things generally work out for me. Heh.
Powered by: GSB CM7
Click to expand...
Click to collapse
Just curious, did you have the opportunity to try the native tethering under Froyo/CM6 as well, or did you only try it under CM7? I haven't needed the tethering since before I started to try CM7, so I actually don't know from personal experience if Cyanogen has made the tethering work correctly under it yet. I didn't have any trouble with it under CM6, besides the usual occasional semi-random tethering failures.
My ubuntu 10.10 install handles native tethering just fine. However, that stupid bug where the Eris loses data connection randomly. while natively tethered kicks in.
The only solution I've found is to use AziLink (seems to solve the random disconnect as well as pdanet does.)
Sent from my Eris using XDA App
adaneshade said:
My ubuntu 10.10 install handles native tethering just fine. However, that stupid bug where the Eris loses data connection randomly. while natively tethered kicks in.
The only solution I've found is to use AziLink (seems to solve the random disconnect as well as pdanet does.)
Sent from my Eris using XDA App
Click to expand...
Click to collapse
Thanks, I'll keep them both in mind. I tried PDANet a long time ago and it didn't keep the tethering from failing, but maybe they improved it.
Hey Guys,
I asked this in the actual rooting thread, but there doesn't seem to be much activity there. Was hoping for an answer by tonight when I attempt rooting.
Got my Thunderbolt yesterday. Didn't have time to root last night, but did go ahead and set up ADB Shell via the youtube tutorial (thanks man).
One issue I noticed was when I went to plug in my TB to a Win7 notebook, it did not give me the option of mounting it as disc drive like the Incredible does. I believe the option I chose was something like "connect apps to pc" or something to that effect and enabled USB debugging. I installed the drivers and added the variables for ADB, then checked to see if ADB was reading my TB via the cmd prompt, and it was. It displayed my serial number and device under list of devices attached.
Everything seemed to be fine, just like in the vid. But, with the mounting as disc drive option missing am I going run into any problems when I begin rooting?
So when you plug your TB into your computer you dont see a screen pop-up on your phone that has options like "Charge only" or "Mount drive"?
I replied in the root thread, but I can do it here too.
If I remember correctly when you first plug it in it doesn't show disk drive as an option. But once you've selected an option, pull the notification bar down and select it again the disk drive option should be there.
If not, you can always push the files to the sdcard with adb (adb push name_of_file.extension /sdcard/).
Hope this helps.
Well, the option is there now. I swear it was not at any point last night. Even after I put the drivers in.
But, both my notebook and TB have been restarted since then. Perhaps this was all it needed.
Thanks to you guys for responding. I'm about to attempt root. I'm just as nervous as I was when I rooted the Incredible for the first time.
Send some positive chi my way!
Hello,
My vibrant got recently run over by a car and the screen doesn't work anymore However, I know that it still can function because I can see the 4 capacitive keys on the bottom light up when I touch them. Is there anyway for me to be able to view the Vibrant's harddrive on my computer without having to switch to USB mode (since my screen doesn't work)?
if you have adb installed and know some basic linux commands you can use ADB to view the contents of your vibrants storage via command prompt and should be able to copy most of your data over. As far as a graphical solution i think there was something being developed called screen cast at some point but i dont think that will be much use to you as i believe it has been abandoned
I am familiar with adb but I can't see my device for some reason when I connect my phone to my computer and run 'adb devices'. I've used adb in the past to push / pull files but I remember having to mount the device from the dropdown menu before it would be recognized. Is there any way to force the phone to be connected? Thank you for your help!
isyiwang said:
I am familiar with adb but I can't see my device for some reason when I connect my phone to my computer and run 'adb devices'. I've used adb in the past to push / pull files but I remember having to mount the device from the dropdown menu before it would be recognized. Is there any way to force the phone to be connected? Thank you for your help!
Click to expand...
Click to collapse
are you on a stock rom? ever since i started using custom roms ive always had ADB debugging enabled, unfortunately you may be SOL if you need to enable ADB debugging as both the adb method and screen cast require ADB to work,the other option is to take apart your vibrant and have the internal memory chip read that way tho your stand a good risk of damaging the internal memory chip
I've got a droid razr; rooted, stock rom
I broke the screen accidentally and now the screen isn't showing anything and touch isn't working.
I'd like to recover all the data off my device, but since it's locked, it won't budge. Drives won't mount when I plug it into my PC.
I've got a previous backup which is a little older, but i'm interested in backing up the actual databases (texts, call logs, etc) and system data too, along with my images and personal data.
Is there any way I can perform a whole backup while the system is locked like this?
I've already searched the forum for previous threads with similar issues, but I couldn't find one with a viable solution.
Any help is appreciated, thanks in advance.
Partial Update
Hey all-
I've partially solved my problem.
I was able to get ADB working miraculously. I downloaded the Motorola Device Manager and installed it, also downloaded the Android SDK/Java SDK;
Using the sdk manager i installed the google usb drivers (im not sure it helped any way, but just in case)
after that I ran through the process of adb
Code:
adb kill-server
adb start-server
**plug in device**
adb wait-for-device
adb get-serialno
From there I was able to use "adb shell" and navigate around the file system; used su, went to /data/system/ and did "mv gesture.key gesture.key.bak"
I then restarted my phone and did a repeat of wait-for-device, and get-serialno just to verify the phone was connecting properly.
I then browsed to my computer and amazingly, the drives mounted, my sdcard, and sdcard-ext as removable drives and I was able to view the contents.
-------
So now, I'm stuck here with a device that's NOT locked, I can view my files, and I can navigate the file system.
My end goal is to be able to copy everything from /data/ to /etc/ /system/ /root/ /sdcard*/ /vendor/ /xbin/ and any other system file that's not available through the mounted drives.
I'll keep this thread updated, and if anybody has any help or clue on how I'd do this, it'd be greatly appreciated.
So far I've tried variations on "adb pull" using / as a root dir; trying to find a way to use the shell to invoke scp, ssh, or some other file transfer, but I get no network connection. While in the adb shell and doing any file operations, I get an error stating that it's a read-only file system as well.
Fixed
I just wanted to let you all know that I've resolved my problem.
Let me state the issue again.
- Screen and touch broke.
- Device locked with pattern
- Rooted
- ICS - Stock Verizon ROM
- USB Mode was UMC, not PTP/MTP
- USB Debugging enabled
I used ADB to delete /data/system/gesture.key and rebooted, effectively removing the device lock, and allowing drives & data on my SD cards to show up in explorer after a reboot of the phone.
After futzing around for a bit, I realized the phone was tied to my Google account, and I remotely installed "Droid VNC Server" (app name org.onaips.vnc)
From there I found a way to activate the VNC server through the ADB command line
Source: android.stackexchange.com/a/31957
Code:
Application located in
/data/data/org.onaips.vnc/files
With a root shell, run this
chmod 766 /data/data/org.onaips.vnc/files/androidvncserver
Then you can execute the vnc server from the command line
/data/data/org.onaips.vnc/files/androidvncserver
Run this to forward the port
adb.exe forward tcp:5901 tcp:5901
On your VNC client, connect to localhost:5901
From there I was able to get access to my home screen and pulled the notification drop down and changed from USB Mass Storage to Camera/Media Mode
Rebooted the phone, started the vnc server again, connected to it and moved some files around to my SD Card
In another adb shell as root, I was able to copy files from /data/data/ (or anywhere else I wanted) and write them to anywhere on /sdcard-ext/
From there in another command shell, I ran adb pull /sdcard-ext/datafolderfile
=========================================================================
I believe this to be the overall gist of things, though I ran into hiccups along the way, while I was messing around, I changed some permissions which caused my su executable to break and only be allowed to run shortly after booting the phone; and also because of the broken screen, something would cause the phone to reboot every so often, breaking my connections, backups, file transfers, and etc
There's also a cool option in adb
Run
"adb backup" and it'll give you all the switches, you'll have to confirm the backup on your phone, so be sure to be running VNC and confirm it, but adb backup should be able to grab everything you need. Like I said it didn't work for me because my phone would reboot;
I hope everybody that sees this can benefit from it
Annafunny said:
So did you extract your data from your Razr with adb finally?
Click to expand...
Click to collapse
This thread is really old (4 years)... and the answer was provided.
To avoid further issues, closed.
--Edit--
This is finally solved. There was a problem with my computer's ADB RSA key, so I simply had to delete the key file and rerun ADB and I Received the RSA Key Fingerprint window instantly on my G3.
For the full description of the problem look here:
I'm having issues trying to root my phone. I'm using the ioroot method mentioned here.
I get to "* daemon started successfully *" then nothing. After a lot of troubleshooting I know it's because my phone won't allow access by my computer. I never receive the RSA Fingerprint window allowing my computer access to my phone. Here's what all I've tried:
-Put phone into Internet>Ethernet mode (and I've also tried Internet>Modem, MTP and Camera modes as well just to say I did).
-Enable Developer Options and enable USB Debugging.
-Installed the drivers linked in the ioroot page (I've also downloaded the drivers directly from LG - believe it or not ... it's the same file).
-Installed the Verizon Software Assistant from the phone after connecting to the computer.
-Updated my ADB version with the SDK Manager.
-Used different USB ports on my computer as well as two different USB cables (one of which came with the G3).
-Checked Device Manager, all is as it should be and no unrecognized devices.
When I ran the adb server without the ioroot batch file, typing "adb devices" would return my phone's serial followed by "offline." It did this until I updated ADB; then when typing "adb devices" it would return the serial followed by "unauthorized." I've tried all various methods and combinations of switching adb debugging on and off, switching developer options on and off, installing and uninstalling and reinstalling the LG drivers, unplugging and replugging the USB cable, power-cycling all devices including myself at night, doing these methods with long pauses in between (10 minutes to ensure I wasn't being impatient), scratching my head, drinking more coffee, switching to rum and swearing at all devices but nothing seems to make a difference.
What am I missing?
I've got the Verizon LG G3 in White (LG-VS985W)
Software version VS98510B
Windows laptop running Vista 32 bit (I know I know, "eeew Vista")
I was able to obtain root using a different computer, here's what I tried with my laptop after gaining root to get it and my G3 on speaking terms:
-Deleted the ADB_Keys file on the G3 (/data/misc/adb/adb_key): no change.
-Compared running Windows services between Vista and 8.1 and started services which were running on 8.1 but not vista: no change.
Here was the resolution:
There turned out to be a problem with my laptop's ADB RSA key. I'm assuming my G3 was rejecting a bad key and disallowing my laptop to connect to it via ADB.
ADB saves a key file in one of multiple places on a Windows computer, the first is in the location where adb.exe is (C:\android), the second is in the user's profile (C:\Users\*username*\.android), the third place is in the Windows system files (C:\Windows\System32\config\systemprofile\.android), the file is simply named "adbkey" with no extension. If there is no key file when ADB runs, it will generate one automatically.
Mine was located in my user folder (C:\Users\*username*\.android\). All I had to do was delete the adbkey file (there was also a file named "adbkey.pub" which I deleted as well), restart the adb server in command prompt (adb start-server) and plug my phone in. I instantly received the RSA Fingerprint Key window on my G3 allowing connection between the two devices. Then typing "adb devices" returned my phone's serial number followed by "device" showing it was available. I went back to the C:\Users\*username*\.android\ folder and sure enought there were new "adbkey" and "adbkey.pub" files.
Problem finally fixed!
Here are some VERY useful links which helped me come to this fix:
How ADB enables a secure connection
Reconstructing ADB's RSA key file
Try using this set of Vertizon g3 drivers: https://mega.co.nz/#!58YHAZaQ!yNlgZG1m7toHBZp_0HF1jSQ66gMoZmmiDrNq9W5aJIc
Open the .zip, run the .msi file on Windows.
I do not run the G3's auto-install software when I plug it into the PC.
I do set the G3 to "PTP" USB before initially connecting to the PC.
The adb file in the ioroot "bts" subfolder should be okay to run on Windows.
When the phone is attached to the PC, change its USB connection type to Internet, with submenu type Ethernet. At least on my phone, right when I change the phone connection to Internet/Ethernet is when I get the phone popup to accept the PC's RSA fingerprint.
If I then run "adb devices" on my PC, I'll see the random ID followed by "attached", which means I have a good connection. If this doesn't happen, unplug, then replug, the USB connection at the PC side.
Then I can "cd .." and run ioroot.bat.
Good luck!
markfm said:
Try using this set of Vertizon g3 drivers: https://mega.co.nz/#!58YHAZaQ!yNlgZG1m7toHBZp_0HF1jSQ66gMoZmmiDrNq9W5aJIc
Open the .zip, run the .msi file on Windows.
I do not run the G3's auto-install software when I plug it into the PC.
I do set the G3 to "PTP" USB before initially connecting to the PC.
The adb file in the ioroot "bts" subfolder should be okay to run on Windows.
When the phone is attached to the PC, change its USB connection type to Internet, with submenu type Ethernet. At least on my phone, right when I change the phone connection to Internet/Ethernet is when I get the phone popup to accept the PC's RSA fingerprint.
If I then run "adb devices" on my PC, I'll see the random ID followed by "attached", which means I have a good connection. If this doesn't happen, unplug, then replug, the USB connection at the PC side.
Then I can "cd .." and run ioroot.bat.
Good luck!
Click to expand...
Click to collapse
... no dice.
Ok, I'm switching to my Windows 8.1 machine (my laptop is my server and android-dirty-work machine).
So it worked without hesitation on my 8.1 machine. I used the drivers listed in the ioroot thread (same as the drivers from LG) and the process went off without a hitch. I have no idea why my Vista machine and G3 don't get along but I'll need to figure it out when I do further adb work because I use my laptop for that.
Thank you markfm for the extra drivers.
I'll call this solved for now but if I find out further reasons why it didn't work I'll post it here for others who have similar struggles.
Ok I finally solved this. It turned out there was something wrong with my laptop's ADB RSA key. All I had to do was delete the key file, run the ADB Server and connect the phone. ADB will automatically generate an RSA key if none exists. The RSA key was located in C:\Users\*username*\.android and was simply named "adbkey" with no extension. There was also a file named adbkey.pub (Microsoft Publisher) which I'm assuming is a viewable version of the key. I deleted both of these, re-ran the ADB server and voila I instantly received the RSA Key Fingerprint confirmation window on my G3.
Done and done!
unable to generate RSA key on my MCB
I've read and re-read all the entries addressing this issue. I have a black G3 and am using a 2013 Mac Book Pro. I've followed the instructions to the letter many times but with no success. I'm at a loss. Any ideas would be greatly appreciated.
scooterd said:
I've read and re-read all the entries addressing this issue. I have a black G3 and am using a 2013 Mac Book Pro. I've followed the instructions to the letter many times but with no success. I'm at a loss. Any ideas would be greatly appreciated.
Click to expand...
Click to collapse
You'll have to bear with me because I'm not familiar with Mac file structure.
I would start from scratch. Do all these before trying to run adb again.
On your computer:
-Delete adbkey & adbkey.pub from the .android folder (I'm not sure where that is on a Mac, Home\.android?).
-I'm not sure if Macs have a device manager, but check that your phone is correctly recognized and the drivers are installed properly.
On your phone:
-Ensure you've got developer features unlocked
-Double check that you've got usb debugging enabled.
-Tap the "Revoke USB Debugging Authorizations" button below USB debugging in developer options.
-When you're plugged in be sure to set your connection to Internet >>Ethernet (you'll see the debugging icon in the notification bar if it's connected right).
I know a lot of that is basic and redundant but if it's all done correctly then it should work. If it doesn't work it gives us a good starting point to troubleshoot.
If you want to test it open terminal, change directory to the bts folder in the ioroot folder and start adb (adb start-server), with everything done right you should get the rsa window on your phone right now. Type "adb devices" and see what comes back.
Thanks for the assistance. I never could get anywhere with my MBP so I used Windows. I downloaded the drivers and got the RSA key after revoking all prior authorizations. However, but my computer still won't see my G3 in internet/usb debugging mode. It reads it in MTP, PTP and USB charge mode. But that's it. I've rooted numerous phones before, mostly Samsung, but this one has me stumped. Any ideas?
scooterd said:
Thanks for the assistance. I never could get anywhere with my MBP so I used Windows. I downloaded the drivers and got the RSA key after revoking all prior authorizations. However, but my computer still won't see my G3 in internet/usb debugging mode. It reads it in MTP, PTP and USB charge mode. But that's it. I've rooted numerous phones before, mostly Samsung, but this one has me stumped. Any ideas?
Click to expand...
Click to collapse
Use whatever mode will enable USB Debugging. If Internet>>Ethernet doesn't work then use any other mode that will. It's not necessarily important what mode your phone is in, but what mode will allow USB Debugging. If you have it in MTP, PTP, Camera or any other, and you have the USB Debugging icon in the notification bar, try the "adb devices" command and if it returns "*serial* device" then you should be good to go to root.
Once your phone has enabled USB Debugging and accepted the RSA key from your computer then the connection is made and your phone will accept the ioroot commands.
scooterd said:
Thanks for the assistance. I never could get anywhere with my MBP so I used Windows. I downloaded the drivers and got the RSA key after revoking all prior authorizations. However, but my computer still won't see my G3 in internet/usb debugging mode. It reads it in MTP, PTP and USB charge mode. But that's it. I've rooted numerous phones before, mostly Samsung, but this one has me stumped. Any ideas?
Click to expand...
Click to collapse
Is your phone a Verizon Model (VS985)? I'm assuming not because I don't have PTP mode on my G3. If it's not Verizon, the ioroot method suggests using PTP mode.
Yes it is a Verizon VS985. I bought it last week. I have four options, charge, MTP, internet and PTP when I connect my phone to the PC. I get usb debugging under either ethernet or modem. Device Manegr sees my phone and I get the RSA key. I never get a terminal which let's me know something isn't right. This is truly weird but I won't give up. I'll start over and see what happens. Again, thanks for your patience.
scooterd said:
Yes it is a Verizon VS985. I bought it last week. I have four options, charge, MTP, internet and PTP when I connect my phone to the PC. I get usb debugging under either ethernet or modem. Device Manegr sees my phone and I get the RSA key. I never get a terminal which let's me know something isn't right. This is truly weird but I won't give up. I'll start over and see what happens. Again, thanks for your patience.
Click to expand...
Click to collapse
No problem at all, happy to help! It sounds like you have everything set up properly, however the terminal doesn't open automatically (you need to do it manually). But you shouldn't need to open the terminal to get ioroot to work, after you've unzipped the ioroot.zip file, simply navigate to the ioroot folder, right-click on ioroot.bat and choose Run as Administrator. That should run through the entire process for you.
If you want to test your adb connection (testing not required for ioroot to work) you'll need to open the command prompt manually. Press Windows Key+R, in the run window, type cmd and press enter, this will open the command prompt. When you're in the command prompt, you'll need to change directory to the location of adb.exe in the bts folder inside the ioroot folder. Mine was in a folder named android on my C drive so the address looked something like this: C:\android\ioroot\bts the command you'll type in command prompt would be: cd C:\android\ioroot\bts then press enter. Then you can type adb devices and see if you're connected properly.
Okay. Here's where we are. I did everything you suggested. I got the RSA key and the G3 went into recovery mode. I toggeld down to the appropriate command and hit the power button. The little green guy fell over with the dreaded red triange and I got the message "This version of ioroot does not support your device/firmware combo. Please downgrade to previously supported software version. My G3 is running VS98510B. I can't post in the devlopment section but wonder if a software update prevents root the the version being used. Just a question but at least I know I'm not going crazy.
---------- Post added at 04:33 PM ---------- Previous post was at 03:46 PM ----------
scooterd said:
Okay. Here's where we are. I did everything you suggested. I got the RSA key and the G3 went into recovery mode. I toggeld down to the appropriate command and hit the power button. The little green guy fell over with the dreaded red triange and I got the message "This version of ioroot does not support your device/firmware combo. Please downgrade to previously supported software version. My G3 is running VS98510B. I can't post in the devlopment section but wonder if a software update prevents root the the version being used. Just a question but at least I know I'm not going crazy.
Click to expand...
Click to collapse
You sir are a genious. After changing my USB cord, I'm rooted and all is well in the world. It's always the little things that matter
My Pleasure! It's the little things that matter and the little things that kill!! I'm glad you're finally victorious!:laugh:
EDIT: Nevermind, I got it to work through Internet>Ethernet.
postal302 said:
Is your phone a Verizon Model (VS985)? I'm assuming not because I don't have PTP mode on my G3. If it's not Verizon, the ioroot method suggests using PTP mode.
Click to expand...
Click to collapse
Hi, hope this thread is somewhat still alive. sorry for the late add on... please help.
Sorry I'm a complete moron when it comes to rooting and ADB / RSA stuff and have no idea what exactly i am doing but for some reason my macbook won't allow me to authorize my oneplus. the authorize computer dialog box never pops up however i get a notification when my phone is plugged in that debugging is active. developer options have been reset, multiple usb cables have been used, and authorization has been revoked multiple times as well.
Im not sure how to access my adb settings on mac and when i attempt to go into terminal and try kill-server / start-server commands i get error messages as commands are not recognized.
Any help is appreciated as i can no longer use stock rom on OPO and i can't go about rooting my device
Wrong forum area -- this is for the Verizon LG G3 smartphone.
Same here! WITH NEXUS 7
Tried all the methods and spent almost 20hrs experimenting to retrieve rsa fingerprint, but in vain
Can you please suggest any remedy?
I cant install any os and unfortunately, my status bar and softkeys disappeared after using softkeyz apk...Dont tell to delete dalvaik data and cache[ it didnt work]
Please...
Jesusmaryqueen said:
Tried all the methods and spent almost 20hrs experimenting to retrieve rsa fingerprint, but in vain
Can you please suggest any remedy?
I cant install any os and unfortunately, my status bar and softkeys disappeared after using softkeyz apk...Dont tell to delete dalvaik data and cache[ it didnt work]
Please...
Click to expand...
Click to collapse
It is also possible to overcome the situation, by installing Mobilego software on your PC and follow the instructions accordingly (connecting your android using usb & debugging etc,.). You will get a RSA fingerprint request.. Easy Once it's done, u can close the mobilego software in the PC and open someother software for example Bacon root toolkit for oneplus one etc etc.. Hope this helps
adbkey doesn't exist
I don't know what i did wrong before, but my computer just DOES NOT have adbkey and adbkey.pub anywhere! First, i thought it was my phone's fault. Then, i tested in a different pc, and it worked. How do i generate those keys? There are no helpful answers in the internet yet...