Hi,
after the upgrade from 1.9.1 to 2.0.0 my DellStreak permanently reboots by itself. I have it on homescreen in standby and 10 minutes later it reboots. Or i write a sms and it reboots. I think every 30 minutes it reboots.
And this is very horrible :/
I flashed it via ClockModRecovery and flasht the new DSP, too via fastboot.
Only baseband i dont flash, but this doesn't matter I think.
Can someone help me.
Did you try a factory reset. I've been reading a lot on the forums about people having random reboot issues, but I have not had one. Be sure that you do the factory reset from the first menu, dells four option menu. Its option number 1. Your phone will immediately reboot after the reset when it does hold down the volume up and down buttons and do the factory reset again for good measure. I always do this and never have reboot problems. Hope that helps.
Sent from my Dell Streak using XDA Premium App
Thank you I will try it now, and repost if problems are solved or still appears.
Yeah. Factory reset, then put the new baseband and amss. Then put streakdroid. In fact, run qdltool first, then do all that, so you'll at least be back to a fresh setup.
Hi ok I think it works fine. I only Hardreset via ClockModRec. And this every Time But ok it works so fine
But baseband is still offline in thread. So I cannot update this, but now it still works fine.
Related
Hi,
Originally my phone was from the UK Carphone Warehouse (CPW)
I have upgraded it from 2.2 to 2.3 etc...
The last time I did a firmware upgrade to ICS was a few months back and I didn't have any problem doing it.
After the upgrade, I had a few bugs. I used this file - GT-I9100_XEO_I9100XXLPW_I9100OXALPW_I9100XXLPW.tar and the main bugs I have are - The screen won't lock and when I press the Power Button, it will turn the screen off but when I hold it for 1 second the phone closes down.
So today I thought, lets see if I can change my firmware to a CPW version, so I downloaded GT-I9100_XEU_I9100XWLP7_I9100XXLPS_I9100XEULP5.tar and installed that. It went through the usual stuff and upon restarting I was getting an "android.core" crash. The screen stops working and after several reboots nothing change. I also booted up and cleared the cache, and this didn't do anything either.
I have just reverted back to the first ICS upgrade but still has not screen lock or when I press the power button for 1 second it closes down.
I wondered if anyone else has had these problems or could recommend to me what may fix it.
I appreciate all help
Thanks
TBS
TheBritScott said:
Hi,
Originally my phone was from the UK Carphone Warehouse (CPW)
I have upgraded it from 2.2 to 2.3 etc...
The last time I did a firmware upgrade to ICS was a few months back and I didn't have any problem doing it.
After the upgrade, I had a few bugs. I used this file - GT-I9100_XEO_I9100XXLPW_I9100OXALPW_I9100XXLPW.tar and the main bugs I have are - The screen won't lock and when I press the Power Button, it will turn the screen off but when I hold it for 1 second the phone closes down.
So today I thought, lets see if I can change my firmware to a CPW version, so I downloaded GT-I9100_XEU_I9100XWLP7_I9100XXLPS_I9100XEULP5.tar and installed that. It went through the usual stuff and upon restarting I was getting an "android.core" crash. The screen stops working and after several reboots nothing change. I also booted up and cleared the cache, and this didn't do anything either.
I have just reverted back to the first ICS upgrade but still has not screen lock or when I press the power button for 1 second it closes down.
I wondered if anyone else has had these problems or could recommend to me what may fix it.
I appreciate all help
Thanks
TBS
Click to expand...
Click to collapse
You're in the wrong section, this has nothing to do with development
Sent from my SGH-I777 using Tapatalk 2
First of all wrong section mate... By the way u hav written it seems that u hav not wiping the DATA or factory reset after every flash. Try wiping DATA before and after flashing.. Also wipe cache..
Hey guys!
Im a first time rooter but somehow managed to root my Dell, flash Streakmod on it and install the DSC 2.0 ROM and then upgrade it to 2.3.
My problem is that the moment I unlock the screen after rebooting the phone I get a wall of notifications telling me that googlewhateversystem stopped working along with other applications. It seems that somewhow the whole introduction part of the phone went to ****.
Help?
Did you do both resets for DSC, namely Option 1 from the main menu and the reset option in StreakMod?
Strephon Alkhalikoi said:
Did you do both resets for DSC, namely Option 1 from the main menu and the reset option in StreakMod?
Click to expand...
Click to collapse
Yes. I installed DSC and after that made a factory reset, wipe cache, wipe dalvik etc... then I rebooted and did another factory reset on the dell standard recovery.
EDIT: I restored a backup and installed DSC again but this time I didnt do a factory reset and just wiped the cache. I managed to get on the phone but now I get constant notifications that android.phone has crashed. Any ideas?
EDIT2: I removed my sim card and restarted the phone. Everything works fine now. Seems like the Rom doesnt like my simcard. Well I guess I wont use it then. The keyboard is way to small anyway. I just wish that there would be a good ROM for me to use.
Pardon my english im from germany
It's odd that you're having such issues. I use DSC myself and have not had any problems using it. In fact, switching back to DSC solved a pair of annoyances that appear in the CM7 ROMs for the Streak: no camera zoom and the dialpad buttons being too small. If you're willing to put up with those annoyances, try using CM7 with _n0p_'s Phoenix kernel or one of the CM7 derivatives like Longhorn. Just be aware that other than DSC none of the Gingerbread ROMs are being actively maintained.
I honestly dont know what the problem is myself... I flashed it with ams and dps and then the recovery, installed the zip, wiped everything, fixed permissions and rebooted.
I tried this several times and everytime it has these crashes that make it unable to use the phone. Also after restoring my backup after the install the buttons on the bottom of the phones flash every minute or so.
Geez... why does it have to be so complicated xD?
EDIT: I decided to take a deep breath and try the whole procedure again. Flashed the phone, installed the zip, installed the update, wiped everything, rebooted, after the boot waited 10 mins and voila! It works like a charm!
If you Strephon now would be able to tell me how to change the keyboard to the default one then I'll gladly give you my thanks!
If you mean the Swype Keyboard...
Settings > Language & Keyboard. Make sure Swype is checked. Tap OK on any popups that appear and exit settings.
When you go to type something, e.g. a response to this post, press and hold the input area (the spot where you type). The menu that pops up should have an option labeled "Input Method". Tap on Input Method to change keyboards.
No I mean the standard big fat keyboard from the original Dell Streak 5 Rom. The DSC one is way to small for my fingers to type fast AND accurate.
The "big fat keyboard" is the Swype keyboard. The only other option is the default Android keyboard, with much smaller keys.
I'm running CM 10 on my EVO. I haven't updated it in a while so it's probably 10.1 or something. Random shutdowns would happen for no reasons sometimes when using the new YouTube app. Then yesterday when I turned on Bluetooth, the phone shutdown by itself. When it reboots it says Android is upgrading... and optimizing apps. Then it reboots and gets stuck in a bootloop. I can boot to bootloader and recovery. I've wiped cache, Dalvik cache, and nothing seems to fix it. Sometimes it boots and I can enter my PIN and use the phone for a few seconds until it reboots itself again. Also, there has been discolored streaks near the sides of the screen. When using the phone they're black, but when the screen is booting they're red on top of the black.
Does anyone have experience with such a problem? I want to try fixing this so I can backup my data before I reflash the ROM or anything.
If it's an older CM release that could be part of your problem. I would update to CM 10.2 and see if the problem persists. I'm currently running the 8/24 IRC build and it has been rock solid. If you continue to have issues you may have a hardware problem.
Sent from my EVO using XDA Premium 4 mobile app
Thanks for the reply. I did a wipe/factory reset from recovery after doing a backup. Everything seems to be okay now. I'm flashing CM 10.2 8/30 from the IRC to try it out.
I have a backup of the state when it wasn't booting properly. I was wondering if anyone had a similar problem with the turning on Bluetooth and then the shutting down by itself and bootloop. I want to be able to recover files from that state.
Hi all, hoping to get some help. I rooted my phone the other week and was using viperrom. I had no problems whatsoever, no glitches that I could remember. That is, until I decided to trade my m8 with a friends Note 3. I factory reset it and give it to her, I left the viperrom on because she didn't mind but then the glitches started to happen. The onscreen bottom 3 buttons disappeared for her (home, back,etc.), So I reset it again but the problem persists. I searched for an at&t stock rom and sideloaded that after master resetting, wiping the dalvik cache and all that... now a different problem popped up. It hangs at the HTC logo for what seems like forever, but then I noticed the volume up and down make a noise as if the phone is loaded up. I pressed the power button a few times and eventually the screen turned on and I could see the home screen. This happens every time I restart the phone and I have tried reinstalling the stock rom a few times. I am now in the process of trying a different stock rom.. the first was odexed and this new one is deodexed, I dont know if that makes a difference in my situation but does anyone know what could be causing this? Any help would be appreciated.
Nvm, after a few more master resets it seems to have sorted itself out... not sure what it was but its gone now.
If its the latest version of Viper, based on 2.22 software, you need to update the firmware package, otherwise the long boot times will continue.
Details here: http://forum.xda-developers.com/showpost.php?p=54408500&postcount=9592
Last night I tried putting Cyanogenmod on my i9300, its a european model that is not locked.
I first tried with the nightly build of CM 11. Flashing went well, but after boot the Phone seemed to crash/freeze after a few minutes. It stopped responding and only gave sound when using the system buttons. after a few presses that freezes too. I was thinking this might be a problem in the nightly build, so I went back in the recovery, cleared things up againa and this time I tried the latest image from the unofficial CM 12 that can be found here: http://forum.xda-developers.com/gal...-temasek-s-unofficial-cyanogenmod-12-t3086689
It seemed that most people have little problem with this version so I gave that one a try. It booted and gave me an error just before the launcher had to startup. but after a reset by taking out the battery, the Phone booted fine and it all went so smooth... but as soon as i got to the point of entering my google account, the Phone frose again. I retried, and again... at that time it was late at night, and the Phone needed to be used today. So I desided to go back in recovery, clean everything out, and put back my backup. Things looked fine... but sadly, at random times th Phone freezes again. its not my Phone but my wife's, she says it hangs using Facebook or chrome. I did not get the chance to look for a pattern yet, but I hope you guys might have an idea whats wrong.
For now I asked her not to use the internet, I'm not sure if wifi or mobile date will influence it, but it doesn't hurt to try.
I have to go to work untill 9pm tonight, and by the time I get home it will probably be 10 or later, so I have little time to work on it.
If anyone can give me a direction to go in or a possible sollution then I would appriciate it. i might have missed something when putting the backup back.
Any idea's?