For anyone looking for a cheap and nice looking solution to have a portfolio case for your gtab:
I tried this out and it worked out quite well:
$13 portfolio from walgreens (any other portfolio may work too)
$5 in velcro
$2 in superglue
$0 for some parts of the original packaging
total $20
here is how i did it:
1. take everything out of the portfolio (paper, etc.)
2. put softpart of velcro on back of gtab
3. put counterpart of velcro on pad site of portfolio
4. put a small piece of the scratchy part of velcro on the inside of the closing lip
5. take the dark styrofome from the orginal packaging and glue it to the left side of the portfolio. Put it a little bit further away from the middle than from the outside, so it closes well over the gtab
6. put an even smaller piece of the scratchy part on left side of the portfolio (see picture)
7. put the gtab onto the left side. just a little bit more to the right, so it closes well
8. put 8-10 inches of velcro (with the protective tape on it) under the gtab
9. close the portfolio. the styrofom should go right over it and protect it well when the portfolio is closed
10. if you want to stand up the gtab to watch a movie, flip the portfolio all the way around and use the 8-10 inches of unused velcro to stand up the portfolio in the angle that works best.
DONE
Looks good and professional when closed. the left side slit in the portfolio can be used for the screen cloth. the styrofome further protects the gtab in case i should be so uncoordinated to drop it.
please look at attached pictures for the results.
that looks great
i think i might do the same with the one i already have since the box i used is already broken. although i was thinking on buying the case that the xoom is using they sell it at best buy. but not really sure if its worth the 50 bucks.
thanks for sharing
Related
Arrrrgh! I'm wondering if anyone has found a (leather) flip case for the AT&T Tilt 2 they are happy with?
My phone is a little over a month old, and I'm getting desperate. I've been temporarily using a clear thing (case mate) AT&T sold me with the phone (it was all they had that would fit) until I found something that would work for me. I've been reading here, and finally took the plunge to get the Designio case discussed here:
http://forum.xda-developers.com/showthread.php?t=584093
Unfortunately, either I got a bad case or I'm being too picky or whatever, but I'm not pleased.
My criticisms are:
The PTT button completely covered by the leather support piece (not sure that's what to call it, but there's a leather piece that runs along the left edge, or bottom with the keyboard open). The PTT button is still functional as long as I press the leather piece just right.
The plastic over the keyboard does not fit snuggly -- it bulges up about an eighth of an inch along the bottom of the keyboard (the left side of the phone), which is annoying enough when using the keyboard, but that bulge also keeps that edge of the phone from closing flat when then keyboard isn't out. I carry my phone in a dedicated pocket in my purse, and I'm constantly finding dust & such that gets under the loose plastic keyboard protector at the bottom of the keyboard (left side of the phone when the keyboard is closed) since there's a gap along that edge from the loose plastic. That's highly annoying for me.
#2 might not be much of a problem if the magnetic closure was snug, but it's not -- IMO, it's off by a little over a quarter of an inch. This allows the top cover to slide around enough that the screen isn't protected when the case is closed (particularly the bottom of both sides up about 2.5" and up to 1/2" in from the bottom corners). If the magnetic catch was appropriately placed, it could also eliminate the gap on the left side of the phone when the keyboard is closed.
Clearly, this isn't the perfect case for me. I thought perhaps I was being too picky, but the Krusell case for my old 8525 doesn't suffer from these problems.
So, if anyone has found a flip case (preferably leather, but that's not a deal breaker) for the AT&T Tilt 2 that doesn't suffer from these problems, please share
TIA,
Saundra
i'm not entirely happy with mine, but mine seems not to have the problems that you are finding wiht yours.
i use the Capdase case, http://www.capdase.com/en/product4.php?cid=1&bid=5&mid=48, and it's a soft leather case that comes in two styles, either a "book"/side flip, or the top flip which i got.
main pro is that it uses small tabs on all 4 corners to clip on to the lower/keyboard half of the phone, allowing you full access to all buttons, the usb port, and the keyboard, without any plastic in the way. the tabs also seem to be more robust and likely to last longer than the seidio innocase tabs which i used on my kaiser. those tend to wear down and break off after about 2 years of use.
on the cons, i dislike the flap, which only has room to store 2 microsd cards and 1 extra sim card. i've already lost 1 sd card, though i am not 100% certain if it was my fault or the case (i was showing the phone to some friends the night i lost it). it also does not have any storage space for a credit card or similar, even though it would've been minimal cost to add one.
if only i could have the flap from your case, and the base of mine. then it'd be perfect.
Thanks for the input! It does sound as though we could have the perfect case with your base & my flap.
I'm in the US, and I couldn't find any retailers for that particular Capdase -- lots for iPhones. Of course.
It looks like I could maybe get it through eBay, which is good to know in case I just can't get the Designo to work for me.
Thanks again!
sslund said:
Arrrrgh! I'm wondering if anyone has found a (leather) flip case for the AT&T Tilt 2 they are happy with?
http://www.noreve.com/brand/HTC/product/Housse_cuir_HTC_Touch_Pro2_Verizon_-_Sprint_Tradition.html -This works well for me, but there are no pouches for SD cards
Click to expand...
Click to collapse
Noreve
I am using the Noreve case available at www.noreveusa.com I like it a lot. It too covers the push to talk button, but since I'm using a custom ROM it has no functionality anyway. The Piel Frama case I had for my Original Touch Pro, there was that darn plastic sheet covering the keyboard and frankly I think that sucks. Granted the noreve case is squirrely when the keyboard is open, but unless you are able to drive and text or ride a bike and text or a motorcycle and text, well you'd do better to spend your money on a funeral plan than a case. My only complaint about the Noreve case is the belt clip sucks. I am using an old Piel Frama belt clip since it fits my belt better. I also personally LIKE the looks of the larger Piel Frama TP2 case, but most have commented on how ugly it looks.
If you're crafty...
As we've come to realize, ATT has delivered the Tilt 2 in a state that requires serious hacks to make the simplest changes. In keeping with that line of thought, I've modified a clear plastic case and added a leather flap with a pocket for credit cards and memory stix. And - Unlike some commercial flaps, when this flap is closed, nothing can slide out of the pocket. Here's how you can too...
Note to Boy Scouts: I've included more detail below than many of you here may need. After buying the case, reviewing the pix and the dimensions, you may be able to fore-go most of the tedious instructions below.
PIX
I've posted a series of pix on photobucket (sadly, I'm too new and untrustworthy to provide direct links to them here). To review the photos:
1. Go to the PhotoBucket website.
2. Click the Drop-down arrow on the right side of the "Search" box and select "People" for the search type.
3. Search for my id, "fractalcracker". Zoom in to view the 5 photos in the default album.
Plastic Case
Two-Piece (front and back) Plastic Case from the ATT store: $29.99 (ridiculous, yes I know...). Find it online at the ATTWireless website by searching "Accessories" for part number "75525". The Back piece clips on to back of phone and allows you to access all buttons and slide open the keyboard. After adding this leather flap, you won't need the front piece of the case.
Leather Pocket Flap
The leather flap is similar to a wallet pocket. In fact you might be able to cut a wallet apart to make the flap. I'll give you directions to make this one by hand from a small piece of leather. If you don't have scrap leather, cut up your wife's (or your own) purse. Good luck with that one...
Leather Measurements:
You'll need a thin, pliable piece of leather 4 inches high by 5-1/2 inches wide. We'll cut 2 pieces as follows...
Outside flap piece:
3-1/4 inches wide from left to right.
4 inches high from top to bottom.
Pocket piece:
2-1/4 inches wide from left to right.
4 inches high from top to bottom.
Assembly
1. Cut leather pieces.
2. Lay the smaller (pocket piece) on the table so that what will be the 'hidden side' (inside of the pocket) is facing up. Align it so the narrow edge is closest to you.
3. Apply a thin bead of super-glue to the top, left and bottom edges of the pocket piece. The 4th, unglued side will be the opening of the pocket.
4. Lay the flap piece down on the table so the inside of the flap is facing up. Align it so the wide edge is closest to you.
5. Pick up the pocket piece and flip it over from left to right so the glue side is down. Align it above the right side of the flap piece and glue the 2 pieces together so the top, bottom and right edges are aligned.
6. To form the hinge, apply a thin bead of super-glue to the flap piece, running from top to bottom along its left edge (opposite the pocket).
For below - remember, we're only referencing the back side of the plastic case - not the front.
7. Lay the plastic case on the table, 'opening-side' up. Rotate it so the camera hole in the back cover is furthest from you. Slide the plastic case over so the right edge of the plastic case is aligned next to the left edge of the leather flap (pocket side up with pocket on the right side of the flap).
When we glue the flap to the case, we want the super-glued hinge joint to be about 1/16th inch below the face of the plastic case. That way, the leather flap will bend back enough to allow the phone screen to slide over it whyen you slide open the keyboard.
8. Stand the plastic case up by raising the left side and tilting it to stand on its right side. Align the right side of the case above the glue line on the left edge of the leather flap.
9. Press the right side of the plastic case down in place on the flap piece so the glue line on the leather flap is about 1/16th inch below the top face of the plastic case.
When it dries, press the phone into the plastic case and get on with your life!
May the force be with you...
Mark
This is a review for
VERTEKS (TM) Asus Eee Pad Transformer PRIME TF201 10.1-Inch Android Tablet Wi-Fi Multi Angle View Leather Folio Case Cover (Black)
PICTURES
The case shipped out of Anaheim, California. As this not is shipped from Amazon at the moment.
I received it in 1 day (shipped via USPS) and the packaging was nicely done, not cheap.
The case some with a 100% satisfaction guarantee card, which is a nice touch. It came with a foam insert to keep case integrity during shipping.
Upon removing from the packaging, the case has a nice leathery smell. The leather is very nice, and has a slight rubbery texture. It is more sturdy than a soft case, but less than a hard case.
It has openings for control of the TFP on top, left right when the case cover it closed. Sadly, the USB plugin is not available when the case is closed (i just charge with the cover tucked back). It also has holes front/back camera, light sensor and the little charging arrow at the bottom of the device
The case is designed to have stand-up support (as seen in the amazon pictures) It is really nice, and uses velcro to stay in place. I played with my TFP considerably with it standing upright and it was very stable.
The inside is coated with a nice, soft, fabric, perfect for encasing the fragile TFP back.
All-in-all, i found this to be a PERFECT case, just what i needed.
Wrap Up
Pros:
Durable leather exterior
Soft, plush interior
Access to top,right,left buttons and slots
Front and back camera/light sensor holes
Stand-up support
Front and back cover
Full access to device touch screen
Cons:
No charging access while screen is fully closed
Feel free to ask any more questions or request any more pictures!
I am very happy to hear this mine just shipped Friday so I should have it soon and I got it for $9.99!
Does it have a closing flap (that is to be wrapped around to the back of the tablet) from the side, where you insert TFP into the case? Do you get what I mean? and where the Velcro exactly is?
Yes and in the form of two 1.25" wide strips that border the charging port giving about a cm of birth on each side of it. It is one solid of piece of leather.
All in all this is a great case the only "flaw" would be that you cant charge it when its closed. But if it was designed the opposite way the web cam and camera operation would be upside down.
If you really wanted to you could cut a notch in the spine area and give it a run on a sewing machine for strength. Then problem would be solved.
I've dropped it a couple times and it was very protective.
Learn from my experience:
My NT was plugged in and charging. It somehow fell 28 inches from the desk top to the wood floor below. The screen is intact and the tablet functions properly, but there was more damage than I would have expected.
There is a crack next to the USB connection. The notch on the bottom left is bent upward and the cover for the micro SD card doesn't want to close completely.
I would have expected it to be more durable than this.
Wow that is crazy. On the plus side, the screen wasn't harmed. I already have a case for mine. but will have to be careful.
I have had no issue with mine sliding off my bed constantly but then again I have a case on mine that extends around the edges a good half inch which means the case is taking the brunt of the force instead of the nook.
drewrauv said:
Learn from my experience:
My NT was plugged in and charging. It somehow fell 28 inches from the desk top to the wood floor below. The screen is intact and the tablet functions properly, but there was more damage than I would have expected.
There is a crack next to the USB connection. The notch on the bottom left is bent upward and the cover for the micro SD card doesn't want to close completely.
I would have expected it to be more durable than this.
Click to expand...
Click to collapse
I'm sorry to hear that that happened to your device. Sometimes I drop my electronic devices and I get butt hurt for a good 10-20 minutes... then come to realize, if it still works, its okay.
By the way, do you work? For less than $20 you can pick up a rubberish silicone case that fits your Nook like a sleeve along w/ a zipper case, shipped. Not bad if you ask me. Some user posted a txt/video review in the accessories forum. If you're not super picky and don't care about how pretty it'll be (not ugly at all) and are just worried if it'll work in a good manner, go ahead and pick it up. If you can't afford it, find your nearest aunt'/uncle or call up grandma...
If you go to amazon (cant post links yet...) search for something like "Barnes & Noble NOOK COLOR eBook Reader Tablet WiFi, Black Soft Silicone Skin Case Cover And Smart Headphone Wrap/Key Chain Style" and "Gizmo Dorks Neoprene Zipper Slip Case (Black) with Carabiner Key Chain for the Barnes and Nobles Nook Color and Nook Tablet"
Trust me, it'll do it's job. You'll feel better w/ it, even if it is not a $30-$40 accessory. You won't even need the latter (zipper case) but it's just an extra level of protection.
Cheers.
I like the Trident cases. They add some bulk but it seems like it will protect well. My Nook Tablet has fallen from the coffee table to the carpet with no damage... but I would expect that even without the case.
I have mine in a Otter Box. It has survived several minor falls. With a 3 yr/o, the Otter Box is a must!
There is an Otter Box available for the NT already? Oh yeah, I suppose it's been out a while for the Nook Color, and they are pretty much the same size I believe. Well, that's good news, I always liked the Otter Box cases (the heavy duty, rugged ones, I think they are called the Defender series). I don't care for their lighter "Commuter" series. Which type is available for the NT? I suppose I could go Google it...
OTOH, I haven't bought a case for mine yet because I like the way it feels in my hand. I just figure I need to be careful with it. I'm not sure I would like it with a case on it...
I dropped mine at home once the day after I got it. I dislike carpet but for once was glad the floor is carpeted. I went to Radio Shack and bought a cover for mine for $30 and I have dropped it once in the cover and no damage was done even on cement. It's a good investment. This cover has 4 elastic straps to hold the tablet (like a book cover) even when in use.
I can't really imagine not using a cover. I've dropped mine several times, from 4 feet down to 1 foot.
If you are worried about dropping or scratching , get a cover .
It's kinda lame to complain
I would have expected it to be more durable than this.
Click to expand...
Click to collapse
I prefer naked devices - covers make the device FAT ... but then I'm double careful with my electronics ....
Good thing I got a case, I seem to be capable of dropping things.
My official B&N case makes the nook easier to hold at least for me so I am glad I got it plus I use it as a stand when watching videos
I'm a big fan of the RooCASE line. I've got the Executive Leather Portfolio variant, but they also make a more compact Leather Case flip cover that has the key feature: A removable "bikini' holster for the device. For throwing in a bag or heavy travel, I use the full case. When I want to use my device at work or around the house, I can pull out the Velcro-attached bikini and have protection while not adding a lot of bulk. There's a rigid back-board that extends just beyond the edges of the device to provide some protection in a fall, and all-around protection that still allows access to everything but the SD slot. What really sells me on the bikini is that I can flip my device 180 degrees vertically and slide it in to protect the screen. The rubberized back on my NOOK is exposed, but the screen faces the semi-rigid back of the holster. The little NOOK carabiner loop is really handy for pulling the device back out.
Hi all,
Here is my review of the Sikai leather/plastic case, as sold by Amazon. For comparison, I have had my Prime in the Poetic cover since I got it. It was okay, but didn't have a charging slot in the spine so it had to be open to be plugged in - plus the nearly-flat angle was nearly-useless because the cover kept slipping out of the tab you tucked it into. I had ordered the GreatShield folio case, but returned it because I didn't like the way the case gripped the tablet, plus I didn't like that to close the cover I had to put pressure on the screen to slide the clip past the edge.
Onto my review...
As mentioned in other reviews, it is a strange mix of black leatherette and dark brown plastic. The plastic back plate is great - the Prime snaps in and seems to be held quite securely. Similar to many iPad covers, it just wraps over the edge - enough to hold, but out-of-the-way enough to really reveal the sleek Prime look. The main portion of the back plate is the black leatherette material, with only the outer edge showing the brown plastic. It has all of the necessary cutouts - including (apparently) the ability to have the dock attached and still close the cover. That is because the "hinge" pieces that connect the cover to the back plate are elastic. I don't have a dock, so I can't comment much on that.
The leather-ish cover looks to be two pieces glued/sewn together, with two bends in the midde - allowing it to be folded up in a triangle shape. Both angles I tried seem to be reasonably stable while typing. About the two layers of the cover...they might have been able to get away with only one, giving it a sleeker appearance, but they had to account for the strap that slips over the sides to hold the cover against the screen. The strap is fine, and gives it an upscale look, but I would have preferred a more unobtrusive solution with magnets or something similar. Overall, the case is skinny enough - just about the same thickness as my Poetic case. That is actually a bit of a downer since I expected this to be thinner since the Poetic case has that layer around the bezel with the magnets in the corners.
There are a few tiny fit-and-finish things that I didn't expect to see in a $30 case. The leather part of the back plate doesn't always make a perfect fit with the plastic border. I'm really nitpicking here, but when this costs three times as much as my Poetic case, I was expecting Ferrarri-quality stuff. I know - it still only $30 so I won't beat them up (much) for it.
Overall, I really like the Sikai. It has a superior look to the Poetic - that one hid all of the nice features of the Prime underneath the protective layers of the front/back/cover. When all that is exposed is the center part of the screen, it almost doesn't matter anymore what Asus designed it to look like. The Sikai shows the Prime's lines and curves much better than the other cases I have seen. The plastic seems tough enough to not break or wear any time soon, so as long as the leatherette holds up, I say this is the best case available for the Prime under $30...
By the way, when ordering from Amazon, it ships from Hong Kong. I placed the order on June 18th, and got a confirmation within 24 hours that it had shipped. However, the confirmation email said my ETA was JULY 31st! Needless to say, I was very happy when it arrived today instead...
I figured there were already better pictures available than my crappy phone can provide, but I can take some close-ups of specific features if requested.
Thanks!
swordsman74 said:
It has all of the necessary cutouts - including (apparently) the ability to have the dock attached and still close the cover. That is because the "hinge" pieces that connect the cover to the back plate are elastic. I don't have a dock, so I can't comment much on that.
Click to expand...
Click to collapse
The dock works great with this case!
yeah I've had this case for a few weeks and its very functional. I really like how it doesn't cover the bezel on the prime like the sikai fiber case and you get multiple angles that actually work
My only complaints are that its a bit on the heavy side and because its designed to be put into the dock with the case on, the steepest angle isn't quite as steep as other cases because the flap slides out making the "hinge" not at the fold but an inch out
oh and the case is kind of ugly haha
This is the case that I've been using for the past month, and for the price it sells for ($15), I am very satifisfied. It's called the Slate Series from Exact Cases. Haven't read much about their cases, but I like what I see so far!
What we have here is a folio type case with a textured pleather exterior, and microfiber material lining the inside of the case. The outside has a grippy, almost rubbery texture, and one thing is that it does get dusty easily, but nothing that a quick wipe of the cloth can't handle. The cover has a solid feel, slim enough to remain portable, but just thick enough to provide some screen protection in your laptop bag.
The main draw of the case is the great array of stand options. First off, the edge of the back shell has a nub which can sit on the three grooves on the inside of the cover, giving three quick stand angle for viewing the 12 inch display. For a more straight up viewing angle, I prefer using the other stand option by folding the cover back and tucking it behind the back shell. This stand is very sturdy and makes watching movies an absolute joy on the 12.2. This would also work as the typing stand by laying it down. The Sleep and Wake feature works as well, another perk.
But again, I just wanted to espouse on the quality you get for the money. Fully featured with a great feel in hand, At $15 with free shipping, this case does all I can ask for at its price. Take a long at my pictures in the link below (too large to link).
Gallery: http://imgur.com/a/hejdh#0
http://www.amazon.com/Exact-Series-Multi-Stand-Samsung-NotePRO/dp/B00IRLEJZQ