Related
Has anyone noticed that their 3D drains while it is plugged in? I plug in my phone for charging. It charges completely and the LED turns green. Then it begins a slow drain (as if it weren't plugged in). I notice the behavior on system panel. It shows I have it plugged in, but my charge is slowly going down.
What's going on here? Is this normal?
I read somewhere that once it is fully charged, it stops taking juice till it drops down to 90 percent and draws juice again while still plugged in.
I think this is from the intelligent charging that most new phones have. In fact in every android phone i have had...i put it on charger at night, wake up and it shows full charge, but if i unplug and replug it will drop down to 94ish and start charging again. I believe it is a form of governor to prevent over charging and heating.
Looking at my Battery Monitor Widget information, charging overnight, the battery gets to 100%, then is allowed to drop to about 95%, then charges up to 100%, then drops, then charges, repeating the cycle between 95% to 100% until unplugged. It looks like a saw tooth pattern.
mevensen said:
Looking at my Battery Monitor Widget information, charging overnight, the battery gets to 100%, then is allowed to drop to about 95%, then charges up to 100%, then drops, then charges, repeating the cycle between 95% to 100% until unplugged. It looks like a saw tooth pattern.
Click to expand...
Click to collapse
noticed this as well
I love Battery Monitor Widget Pro.
I checked my log file from over night and noticed the same pattern. Goes from 100 to 95 percent. Pretty cool.
mevensen said:
Looking at my Battery Monitor Widget information, charging overnight, the battery gets to 100%, then is allowed to drop to about 95%, then charges up to 100%, then drops, then charges, repeating the cycle between 95% to 100% until unplugged. It looks like a saw tooth pattern.
Click to expand...
Click to collapse
seems HTC tweaked it since the EVO 4G, it would drop to 90 not 95. I been using that widget, too, to monitor it.
anyone notice when it starts to cycle back to 100 it stays 99% for a while longer than what would seem normal?
Hi,
My phone goes to 99% charge without a hitch but wont go to 100%
At 99% battery my i got 4207mV
All i did was to follow the instructions on this thread
http://forum.xda-developers.com/showthread.php?t=1198333&highlight=battery
Before that 100% is no problem and after that stuck with 99%
and one more thing my phone shows me messahe on lock screen that phone is fully charged unplug but when i see the battery its just 90%.
From 90% onwards i see unplug message.
I am using Alien#4 ROME and Atrix-GB-Kernel-0.1.7-ext4-sv Kernel
Any suggestions or i am just over thinning ?
Same thing continually happens to me. I've done all the "fixes" and suggestions..and it still does it. Sometimes it goes up to 100%..sometimes 95%. All's I ever do is reboot with the phone still plugged in and "usually" (not always), it boots up showing 100%. IMO there is something with GB that is causing it..cuz i've noticed it on every rom i've tried (Alien, Cherry, CM7 etc)..
=>
Same here. It won't charge past 89%, and it did the same in the past at 92/93 %. I fixed it with a hard reset, but don't feel like doing that again.
Sometimes when I disconnect the charger, the phone still acts as if the charger is plugged in. Only solution is to reboot.
I will try to reboot with the charger connected to ser if that fixed my battery metter. Thanks for sharing.
Whipon said:
Same here. It won't charge past 89%, and it did the same in the past at 92/93 %. I fixed it with a hard reset, but don't feel like doing that again.
Sometimes when I disconnect the charger, the phone still acts as if the charger is plugged in. Only solution is to reboot.
I will try to reboot with the charger connected to ser if that fixed my battery metter. Thanks for sharing.
Click to expand...
Click to collapse
Another thing i've done (as per xploited's thread), is when phone is fully charged reboot the phone (while still being plugged in) and pop out the battery right away. The phone will reboot with a ? (looking for the battery)..then pop the battery back in and it will usually say 5%. Leave it charging until it reaches 10% (i've never gotten it to go higher)..at which point unplug and reboot your phone.
Just read this interesting tidbit from another thread:
"Recently i have tested "Battery left widget", a market app.
When i go in "Summary" and "History" and "Sensor usage" option, i see this :
Sensor is activ "all the time" since last "plug on wall".
Sensor is in use by "Android System"
I have test this :
Charge 100% (and calibrated with CMW wipe battery or "BatteryCallibration" app before), unplug, and REBOOT.
This manual reboot stop "Sensor" activated by recharg.
After this simple action, battery drain has disapeer, and "sensor" activity too
Battery drain is the same than Froyo, 1 day in suspend mode, 1 hour game, 1 hour web and 15% battery left. It's magic !
I think, System detect the wall plug, and activ "something" in system nether desactivated after unplug.
Reboot is the only way to stop this sensor, and baterry drain"
So basically..after fully charging your phone..reboot with it unplugged and it should eliminate some of the drain people are experiencing. Until a new version of GB comes out..I think we'll all have to deal with these weird battery issues.
same issue here with alien 4
it was all good i used to get a very impressive battery life. but after i put alien 4 ( before that i used first ken's release of GB ) the battery life is worse and it doesn't charge till 100% and the drain from from 98 to 90 is very quick compared to other drains in range of 10%
With the 1% mod your phone thinks that the battery is at 100% while at 95%... like 94% would be 90% so it would take a while to get to the full 100 because it doesn't want to overcharge the battery and damage it. Also don't worry about the 100% 4200mv is the normal capacity of the battery's cells aslong as it that or over its still fully charged
Sent from my MB860 using XDA App
As mentioned above, you're fine if you're at 4200mv. Ymmv because of battery. And the juice is calculated by software. No chip on the battery. If your mv are significantly under 4200 mv then you need to calibrate. If it's close or over, quit worrying and rebooting and just use it. Sometimes my phone flies through 90's but after that it settles down and everything is normal. If you keep trying reset battery stats your battery is not going to calibrate because you're not discharging enough for the software to figure out more accuracy with numbers it gives you.
I voided my warranty.
Without any thing doing battery is back to 100% charging
Yep, what the other posters wrote is right. To summarize:
1. If you are at 4200mv, stop worrying what % it shows, because you are at full charge.
2. Android software tries to keep the time when battery is @100% to a minimum, because fully charging and completely discharging on regular basis hurts the battery.
3. The battery meter is lying to you, and it's not such a bad thing, read the article -
http://phandroid.com/2010/12/25/you...is-lying-to-you-and-its-not-such-a-bad-thing/
I love u guys.
No Homo OFC
It was working fine before I went to bed last night, then I let it charge for the night since that battery was at about 4%, But this morning it won't turn on at all. The battery feels warm as if its been charging but nothing seems to be making it turn on. Any ideas?
re: No Poweron
labou_7 said:
It was working fine before I went to bed last night, then I let it charge for the night since that battery was at about 4%, But this morning it won't turn on at all. The battery feels warm as if its been charging but nothing seems to be making turn on. Any ideas?
Click to expand...
Click to collapse
If it was my phone here is what I would do.
First I would see if the phone charges the battery by putting the battery into
the phone and plug the usb cable from phone into the wall charger or into
the computer.
If the display on phone shows a picture of a battery charging let it charge
for an hour more or less and try turning on the phone.
If the phone is not charging the battery I would purchase a cheapy battery
charger and battery combo on eBay.
You can find this combo on eBay for less than $8 bucks shipped for both the battery and charger:
http://www.ebay.com/itm/1800m-BATTE...045605?pt=PDA_Accessories&hash=item43aa9a4465
(even if you decide to return and exchange the phone its still a good thing to have a spare battery and charger)
Check it out.
Good Luck!
labou_7 said:
It was working fine before I went to bed last night, then I let it charge for the night since that battery was at about 4%, But this morning it won't turn on at all. The battery feels warm as if its been charging but nothing seems to be making it turn on. Any ideas?
Click to expand...
Click to collapse
are you on cm7? not sure about the s2 (never had the issue), but i know that on the infuse, there was a problem (or maybe it was intentional) with low power charging mode (phone wouldn't charge when off).
i think this can be solved by trying to charge the phone via your computer usb, as opposed to your OEM wall charger.
Thanks for the suggestion. It definitely isn't showing the picture of the battery when its plugged in to the wall or the computer. I'm debating the battery charger combo you linked.
I actually am. But I have it plugged to my computer and nothings changed.
Time for some trouble shooting.
Start eliminating possibilities. You need to determine where the problem is.
From what you say, it seems possible that the battery is completely discharged but not recharging. That could be a bad battery or it could be the phone.
If you know someone else with an SGS II, try inserting their battery temporarily to see if your phone will boot. If you don't know someone else, maybe you can borrow a charged battery from the store where you bought it.
Continue on until you pinpoint the problem.
Do NOT buy a "cheapie" battery for your SGS2. Unless you want to eisk causing damage. The stock battery for the SGS2 has NFC technology built into it. Using anything other than OEM could cause damage/performance issues to your phone, and void the warranty.
Sent from my SAMSUNG-SGH-I777 using XDA Premium App
Have goh tried a battery pull? Unplug the phone, pull the battery and let sit for a few minutes to allow tbe IC's to discharge. Put battery back in and try powering up the device. Good luck.
Sent from my SAMSUNG-SGH-I777 using XDA Premium App
Similar issue and got phone fixed finally
Have had similar issue as yours. Cable charger was plugged into the phone to be charged at night and was surprised to find that the phone became hot and battery was not charged at the next morning, in fact the battery level got lower than it was before charging.
Notes:
- ROM in use: AOCP version 7.2 (Android 4.4.2)
- Kernel in use: Version 3.0.101 [email protected] #3
Here are some tests done and the observations after getting a charger with a slot to place the removed battery for charging:
1. Charging via USB cable connected to PC:
- With the phone turned on, battery charging icon is only displayed after some wiggling at the charging port. The phone got charged further to 100% when the initial remaining battery level is 90%. However, when the initial battery level was less than 50%, the battery level continued dropping ALTHOUGH the battery charging icon was displayed.
- With the phone turned off, battery charging icon is only displayed after some wiggling at the charging port. When the initial battery level was less than 50%, the battery charging icon displayed only a battery level of 1% and the battery level did not increase at all after 15 minutes of charging.
Initially suspected that it was a dead battery issue and bought an i9100 battery, I thought it was a compatible battery at first. With the i9100 battery, I repeated the above tests.
2. Charging via USB cable connected to PC:
- With the phone turned on, battery charging icon is only displayed after some wiggling at the charging port. The phone got charged further to 100% when the initial remaining battery level is 90%. However, when the initial battery level was less than 50%, the battery level continued dropping ALTHOUGH the battery charging icon was displayed.
- With the phone turned off, battery charging icon is NOT displayed but the phone screen flashed continuously, and at times the phone is turned on automatically as the USB charging port is inserted. When the phone is turned on, the charging proceeded as the above sentence.
Upon searching the forum, I found that i777 has a different battery with NFC chip and i9100 battery has reported to cause issues during charging on i777 devices. There was also a Chinese forum which mentioned that the battery compatibility issues should have been overcome in ROM with Android version 4.0 and above.
I then bought a new i777 compatible battery and tested charging via USB cable. The observations are same as the first battery as at 1.
With the battery issues possibility eliminated, I approached a phone technician to examine the phone by telling him that the phone couldn't be charged and the battery level continued dropping even with the battery charging icon displayed. The phone technician then thought that the USB charging port to be the cause of the charging issue and replaced it. The replaced part is the small metal housing where the USB cable is inserted, and is replaced by heating the old metal housing and replacing it with new part by soldering.
The phone could be charged with USB cable as usual after the part replacement and all the batteries are found to be still working fine. Ended up with 2 i777 batteries and a i9100 battery, may be I could continue using this phone for at least another 5 years down the road.
hi guys! i'm running cm7.2 on my su660 (it's a kang build which is ported from p990 official CM build). and i have a problem on charging the phone. when the phone have 10% of battery left, i plug in the charger, the phone show the charging symbol . but when i leave it sleep and come back after 'bout 3 hours, it still show 10%. but the voltage in sparepart is aproximate 4200 mV. so the battery is fully charged but the rom didn't regconize it. but then after some minutes turning the screen on, the rom show that phone is fully charged. so i guess that the battery percentage counter doesn't work why the phone is pluged in and sleep. so this is a rom issue? can i fix it myself?
PS: sorry for my poor English because i'm not a native English speaker. i'm from VietNam. i tried my best to explane my case. hope u can understand me!
If, after rooting or more likely that case after flashing a new rom, you often have battery reporting errors, and re-calibrating the battery along with some steps I will outline for you below will ensure that your battery is getting a full charge, and the battery reporting accuracy is right on. As far as power cycling, I don't know that it does much good. I run my device in performance mode all the time, and with a CPU overclock of 1.25GHz and various tweaks, I have about a day an a half to a day and a quarter of full runtime from my battery. This is with moderate to heavy usage (calls, emailing, text, gaming, web browsing, etc.) so you should have no problems getting acceptable battery performance after following these steps:
1. Take the case off your device (one of the latter steps involves taking the battery out from the phone while it's plugged in. Make sure your case won't stand in the way.)
2. Install Battery Calibration app from the market
3. Plug in your device to charge while it's on, wait till it gets to a 100%
4. When the charge is 100%, open the BatteryCalibration app and lookup what the charge is in MV while at 100%. Write it down.
My Atrix 2 was showing ~3400MV while at 100%, which is definitely not the maximum capacity.
5. Discharge your device completely until it shuts off.
A good way of doing this quickly is by turning on wifi, and a video player.
6. Without turning on the phone plug it into a wall charger and let it get to 100%
7. When it's at 100%, without unplugging it from the wall charger, take off the battery cover, and take the battery out.
Your phone will "reboot" and show a Missing Battery icon.
8. Without unplugging the phone from the wall charger or turning it on, put the battery back in and wait until the phone recognizes the battery.
9. Your battery should now be recognized by the phone, and showing a charge % significantly lower than 100%.
Mine showed only 5%.
10. Let it sit there charging for 2-3 hours (or more).
My phone wouldn't charge past 10%, but yours might. The numbers don't matter much as the phone is definitely getting additional charge that could have been lost while flashing ROMs, etc.
11. After 2-3 hours (or more), turn the phone on while holding the volume down button and get into CWM (if installed) or use Rom Manager (is device is supported).
Do not disconnect it from the charger still!
12. Wipe battery stats in CWM, reboot.
Do not disconnect it from the charger still!
13. When the phone turns on, go into Battery Calibration app again and look up your MV numbers -if you were like me, they should be significantly higher than before. After this whole process I had 4351MV at 100%, comparing to 3400MV before calibration.
Do not disconnect it from the charger still!
14. Before going to sleep - Install Watchdog Task Manager Lite from the market. Go into it's preferences, set CPU threshhold to 20%, check "Include phone processes", check "Monitor phone processes", check "Display all phone processes", set system CPU threshhold to 20% as well.
Do not disconnect it from the charger still!
15. Make sure your wifi and data connections are off. Now finally unplug the phone from the charger.
Go to bed, let your phone sleep too.
16. Success! Next morning check where your battery % is at and if you followed the instructions correctly / got lucky like me, your battery life should be 90% or more.
I went to bed with 98% and woke up to 94%. So, I consider this mission a success.
Sent from my MB865 using xda's premium carrier pigeon service
i hv bnattery problem for 3-4 month
still cannot solve the battery problem
i think i have done some wrong steps in the battery calibration
when my battery is fully charged in a battery changer(charger for battery only)
when i put the battery into the phone, it's shows that there is about 30% of battery
when i further use the battery, the battery level rise (without charging!) to 100 then drop to 0 and turn off
the time that the phone can use from 100% to 0% is quite short
when every time after charging, the battery level is 100%
it won't charge to the "real" full battery level, ie ~30% (SORRY FOR MY POOR ENGLISH)
how should i calibrate?
i used the battery calibration app, but no use.
Charge to 100 then use battery calibrator from market very simple
Sent from my SCH-I500 using XDA
If your recovery is ClockWorkMod, then there is an option to "Clear Battery Stats". Just try to see whether it helps.
~Cheers
It's a few days late, but battery calibration is unnecessary on modern batteries (Lithium). All the apps do is delete a small file that records power usage, they do not affect battery life in any way. This file is cleared automatically (by the system) when the phone is fully charged.
Further, full charge/discharge cycles will actually have a net harmful effect on your battery life. A lithium ion battery has a limited number of charge/discharge cycles it can sustain before becoming more effective at being a paperweight than powering anything. The full cycles you are doing simply eat into the battery's overall life expectancy.
For instance, it is better to charge from 50% to 100% multiple times than it is to go from 0 to 100 once.
Personally, I would just replace the battery.
I would suggest u to calibrate the battery in the clockworkmod recovery too
if this wont has any effect take into consideration that your battery might be damaged
i faced this problem one year ago with a galaxy spica the battery was shown as full and after a restart it was almost empty and calibrating the battery did not had any effect
so have a try and report afterwards
If, after rooting or more likely that case after flashing a new rom, you often have battery reporting errors (as mentioned above), and re-calibrating the battery along with some steps I will outline for you below will ensure that your battery is getting a full charge, and the battery reporting accuracy is right on. I run my device in performance mode all the time, and with a CPU overclock of 1.25GHz and various tweaks, I have about a day an a half to a day and a quarter of full runtime from my battery. This is with moderate to heavy usage (calls, emailing, text, gaming, web browsing, etc.) so you should have no problems getting acceptable battery performance after following these steps:
1. Take the case off your device (one of the latter steps involves taking the battery out from the phone while it's plugged in. Make sure your case won't stand in the way.)
2. Install Battery Calibration app from the market
3. Plug in your device to charge while it's on, wait till it gets to a 100%
4. When the charge is 100%, open the BatteryCalibration app and lookup what the charge is in MV while at 100%. Write it down.
My Atrix 2 was showing ~3400MV while at 100%, which is definitely not the maximum capacity.
5. Discharge your device completely until it shuts off.
A good way of doing this quickly is by turning on wifi, and a video player.
6. Without turning on the phone plug it into a wall charger and let it get to 100%
7. When it's at 100%, without unplugging it from the wall charger, take off the battery cover, and take the battery out.
Your phone will "reboot" and show a Missing Battery icon.
8. Without unplugging the phone from the wall charger or turning it on, put the battery back in and wait until the phone recognizes the battery.
9. Your battery should now be recognized by the phone, and showing a charge % significantly lower than 100%.
Mine showed only 5%.
10. Let it sit there charging for 2-3 hours (or more).
My phone wouldn't charge past 10%, but yours might. The numbers don't matter much as the phone is definitely getting additional charge that could have been lost while flashing ROMs, etc.
11. After 2-3 hours (or more), turn the phone on while holding the volume down button and get into CWM.
Do not disconnect it from the charger still!
12. Wipe battery stats in CWM, reboot.
Do not disconnect it from the charger still!
13. When the phone turns on, go into Battery Calibration app again and look up your MV numbers -if you were like me, they should be significantly higher than before. After this whole process I had 4351MV at 100%, comparing to 3400MV before calibration.
Do not disconnect it from the charger still!
14. Before going to sleep - Install Watchdog Task Manager Lite from the market. Go into it's preferences, set CPU threshhold to 20%, check "Include phone processes", check "Monitor phone processes", check "Display all phone processes", set system CPU threshhold to 20% as well.
Do not disconnect it from the charger still!
15. Make sure your wifi and data connections are off. Now finally unplug the phone from the charger.
Go to bed, let your phone sleep too.
16. Success! Next morning check where your battery % is at and if you followed the instructions correctly / got lucky like me, your battery life should be 90% or more.
I went to bed with 98% and woke up to 94%. So, I consider this mission a success.
Sent from my Atari Falcon030