Hello everyone. I have a question about the current state of my Vibrant. Coming from a G1, I just upgraded to the Vibrant and have been loving since. I rooted my device, installed Clockwork Recovery, and flashed a new Rom. I decided to switch back to the stock rom but now when I turn on my Vibrant, it just sits at the Vibrant Samsung boot screen... Here are the steps I did up until this point:
1. Starting from the Stock T-Mobile rom, I applied Root update zip but booting into Recovery Mode (Holding down the volume Up/Down buttons and then pressing the Power button).
2. Installed Clockwork Recovery, and then did a Nandroid Backup.
3. Using Clockwork, I installed Eugene's Vibrant7 rom (I left create ROM Backup and Wipe Data options checked)
4. Vibrant7 rom flashed successfully but decided to switch back. So I used Clockwork to boot into manual recovery mode, selected Nandroid and then Restore
After it finished the Restore, it now sits at the Vibrant Samsung boot screen everytime I power it up... I'm thinking I should have not have used the Nandroid Restore to revert back to the stock ROM (unless I'm totally mistaken, I never used Clockwork Recovery before and have flash roms before with my G1).
At this point, could I just reflash back to the stock firmwire using ODIN (Directions from this thread [ROM] OFFICIAL T-Mo Vibrant JFD ODIN/Nandroid Backup Images 7/29/10 (Tested/Working) in the Vibrant/Android Development section). Would that take care of my problem or is my phone currently 'bricked' or SOL?
Thanks in advance for any help or clarification
yeah just odin back to stock... Read the directions carefully
this exact same thing is happening to me. I have tried to follow the instructions to odin. but when I hold volume down and power it just keeps rebooting to the vibrant page. but if I hold volume up and down and power I can get into recovery but non of the options fix my problem. Am I screwed or am I doing something wrong.
i'm having the same problem...stuck on boot screen
i'm on the bell network, are there instructions on how to use odin to fix my phone?
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
flashed a sgh t959 with a galaxy s i9ooo kernel oops
hi im stuck in manual mode and when i try to boot the screen shows two different galaxys s screens then goes back to manual mode and i cant get into down load mode it just goes back two manual mode was trying to root used wrong file i think im screwed i flash with oden and used i9000xxxhph tar file
Same with me, I think I soft bricked my vibrant, so I tried to restore to stock rom using odin. Odin detects it and runs stock rom just fine, but once it was restarting, the phone would not still boot up and would stay stuck at the vibrant samsung screen. I tried other roms such as froyo no brick, and i9000 stock rom also, would not boot also, just stuck at the samsung screen. What do I do? Odin works through the process fine though......why isnt it fixed?
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
yes yes yes! your mistake was using the power button! Lol.
FUTURE NOTE: if you upgrade to any gingerbread roms.... new bootloaders are required. If your JIG didnt get you into download mode before...... then it isn't working right. Once your into the the new Bootloaders for gingerbread, the sequence is........ HOLD VOL UP and POWER until you trigger DL mode. No USB required.... DO NOT FLASH NEW BOOTLOADERS WITHOUT A WORKING JIG IN YOUR POSSESION. TEST IT BEFORE YOU FLASH. I had...... an experiance.... lol
Not working
ParaMount33 said:
OMG MAN!!! i love you! this did it for me, i even went and bough AND made a jig but none worked, didnt boot up into dl mode, just stayed stuck at vibrant boot screen, this did it for me, thx man, saved me hours of stress
Click to expand...
Click to collapse
I tried all the instruction still stuck on Vibrant logo if i connect cable the Loader pix cums but doesnt load or show me battery image what to do now? also Odin doesnt recognize neither i can go to download mode!!!!!
If you can get in DL mode you are halfway there, next make sure you have correct drivers. Uninstall current drivers and reinstall correct drivers. Odin can be funny sometimes, you might need a new USB cable, try every USB port as well.
You can also use the All In One (AIO) program to get drivers and back to stock. If you are having issues with Odin try this
http://forum.xda-developers.com/showthread.php?p=11358713
sent from the depths of helly bean
hi,
Once i gt a prob restoring. But then I re-flashed the ROM which the nandroid backup was taken and then in CWM selected advance and gave restore data option(as i remember).. (it was not full restore with system..b/c I flashed system separately)
You can go back to stock using ODIN .. as mentioned by Daddy_617 previously.
tc
Also if Odin doesn't work for you try Heimdall. I've seen post where this has worked for others.
Vibrant stuck on "Vibrant Samsung"
Daddy_617 said:
Try this,
1. Take out simcard ms and battery
2. Make sure you have the right drivers for your os
3. Open odin
4. Put your battery back in
5. Hold both volume up and volume down, using two fingers,
just to make sure your not missing a button.
6. Slowly... SLOWLY... put the usb into your phone while doing step 4
7. Continue to hold,
8. Should be in dl mode
If your not take out the battery and repeat 4-7. If odin doesn't recognize your phone, try unplugging the usb wire and reconnecting it.
Click to expand...
Click to collapse
I tried this but the say thing keeps happening ... really need help
Hey guys I know this wasn't the right thing to do but it happened....
I was using macnut R10 and was having calling problems, decided to restore a back up which was a bionix 2.1 rom... Because you cant go from a 2.2 rom back to 2.1 rom with a backup because the kernel wont work my phone now will not boot. It loads the both splash screens but gets stuck at the 2nd screen.
I have tried:
1: adb... no devices connected
2: put bionix w/ kernel on the sd card as a update.zip... rebooted the phone holding vol up/down it went into the stock style recovery and gave me the 4 options (reboot/flash update/wipe data/wipe cache) I tried to flash the update.zip and it says:
finding update
opening update
cannot open update (/sdcard/update.zip) no directory/file found
I also wiped data and cache after this and when I reboot (only the first reboot after this is done) on the 2nd splash screen it plays half of the bionix boot sound then cuts it off and just sits...
EDIT: *** just realized why its not finding the update.zip... because I put it on the ext sd card... but either way I cant adb to push it to the internal sd card
3: then I tried to flash back to stock with odin but cannot get into download mode... I plugged the usb in and held vol up/down as I powered on but it just brings me back to the stock recovery instead of download mode
If anyone knows what I can do to either flash a rom/kernel or get into download mode so I can just flash back to stock, I'm all ears for any suggestions
thanks a lot for any suggestions in advance...
Take battery out then plug in usb then hold volume buttons while you place battery back in you should be in download mode hope it helps
Still flashing , thanks to odin & tw
Try getting into Download mode using the GT-i9000 way, cause I once screwed my phone up and did that, just do a simple search on how to enter download mode the i9000 way
Sent from my SGH-T959 using XDA App
ahh thank god i think i was holding power when i put the battery in last time... now lets hope odin doesnt freeze lol
I had Trigger on my Vibrant, and decided to give Bionix Final RC1 a try. So I put it on my SD, went into Clockwork, checked wipe data and backup, then went through the process. It appeared to be installing just fine. But now I'm stuck at the Vibrant boot screen. I did some searching and booted into a recovery prompt, I wiped the data, cache, and reinstalled the packages. No luck. I then saw some stuff about using Odin, but I can't find my phone/storage with it. Any ideas how to get this back to normal?
Thanks
Restore your backup through recovery
Sent from my SGH-T959 using XDA App
I'm still learning as I go, but would the backup have been deleted when I wiped the data? Also, where do I restore this? I tried searching for other boot options, but only came across the usb power + vol up/down + power, and then the same thing, but releasing the power button when the screen goes black.
Thanks!
just odin back to stock and then root with the updat package way!
power off phone
pull out battery
turn on odin
attach phone to pc with usb cable
now while holding down both volume buttons put battery back in.
now you should be in download mode and go back to stock with odin from here!
make sure u put the proper .pit and .pda file in there proper places on odin and ur set to go.
Enjoy and also make sure u have the proper samsung drivers
Ended up finding this - http://forum.xda-developers.com/showthread.php?t=734475
But I had to go here for the files, since the other ones are dead. - http://androidspin.com/2010/08/09/how-to-restore-or-recover-your-samsung-vibrant/
Thanks a lot for the help! I'm back on the stock ROM.. for now.
I flashed a kernel on my S3 via recovery and then reboot my phone. It goes to a black screen now. When I pull the battery and power on holding volume down to go into recovery the Samsung Galaxy S3 logo keeps appearing and disappearing until I let go of the volume down key. Then it's stuck at the same black screen. When I try to put the phone in download mode to re-flash via odin it does the same thing. I'm pretty sure I'm fu*ked, but I just want to make sure there's not a way to fix this. Any ideas?
Chaos Residue said:
I flashed a kernel on my S3 via recovery and then reboot my phone. It goes to a black screen now. When I pull the battery and power on holding volume down to go into recovery the Samsung Galaxy S3 logo keeps appearing and disappearing until I let go of the volume down key. Then it's stuck at the same black screen. When I try to put the phone in download mode to re-flash via odin it does the same thing. I'm pretty sure I'm fu*ked, but I just want to make sure there's not a way to fix this. Any ideas?
Click to expand...
Click to collapse
Don't worry..i have done worse things with my phone and yet to brick it..
Fist thing to go into recovery you hold vol up + power + home and not vol down..
Second thing what you will have to do is after the Odin flash..press and hold vol up+power+home..you will boot into the stock recovery..from here do a factory reset but mind you all the data on your internal sdcard will be lost when you do this..now reboot your phone..your phone will boot up properly now..assuming that you have flashed the firmware properly in Odin..
Chaos Residue said:
I flashed a kernel on my S3 via recovery and then reboot my phone. It goes to a black screen now. When I pull the battery and power on holding volume down to go into recovery the Samsung Galaxy S3 logo keeps appearing and disappearing until I let go of the volume down key. Then it's stuck at the same black screen. When I try to put the phone in download mode to re-flash via odin it does the same thing. I'm pretty sure I'm fu*ked, but I just want to make sure there's not a way to fix this. Any ideas?
Click to expand...
Click to collapse
As zoot1 replied to you for download mode press vol down+home+power for a few seconds......for recovery vol up+home+power.........
And make very sure the kernel you flash is compatible with your phone and firmware!!!!!!!!!!!! The rest zoot1 explained in his reply
Good luck
Sorta Bricked
Anyone have an idea what I've done.... Black screen with blue light. I can get to the recovery menu, clockwork is installed, but I can't flash a rom. The only way to get the phone to stay off is by removing the battery.
This is a Cspire L710. I've attempted to flash a Cspire_nandroid_stock zip, the phone will find it but can't open it. I missed a step somewhere I guess. I had it in download mode but made the mistake of trying the factory reset-which changed that.
I've also tried a couple of other roms with the same results.
db1117 said:
Anyone have an idea what I've done.... Black screen with blue light. I can get to the recovery menu, clockwork is installed, but I can't flash a rom. The only way to get the phone to stay off is by removing the battery.
This is a Cspire L710. I've attempted to flash a Cspire_nandroid_stock zip, the phone will find it but can't open it. I missed a step somewhere I guess. I had it in download mode but made the mistake of trying the factory reset-which changed that.
I've also tried a couple of other roms with the same results.
Click to expand...
Click to collapse
go to download mode and flash a stock rom via odin
Cant's get to Download mode
Unless there is a way to get to download mode through the recovery menu, download mode is not an option.
db1117 said:
Unless there is a way to get to download mode through the recovery menu, download mode is not an option.
Click to expand...
Click to collapse
Well i suggest u send it with its warranty or u could check out my sig and build ur own usb jig
Sent from my GT-I9300 using xda premium
You might be able to get to download mode via a usb jig.
I have an issue.. I was in the middle of downloading some files to start a new theming process and went to boot into twrp recovery to flash Jedi ROM that i have been using and my phone froze on the Galaxy Note II screen. I pulled the battery and then did the manual recovery(hold volume up, home button and power) and it just stays at the Galaxy Note II screen...and nothing.. no download mode, no recovery.. nothing. I need help. I plugged my phone into the computer and it does NOT recognize it.. SO I would think of flashing a new recovery or rom thru abd but I can't.. If any one can lead me into the right direction I would appreciate it!!!:good:
PS I see a little red light flash near the speaker on top when I just tap the power button..
UPDATE: was able to get into download mode(odin), but as soon as it shows up it says Downloading..??just need to know the steps of getting rebooted, can I flash a ROM in Odin bc i remember seeing something specifically saying not too.
FIXXED Thanks anyways!!!!!!!!!!!!!!!!!!!!!!!