Im giving my wife my laptop now that I have a transformer and dock for it. Unfortunately occasionally with work, I am going to need to connect to a wired network connection. I was thinking about getting a USB wired (you know, RJ45) network dongle, but I doubt its going to work purely on the basis of driver support. Thoughts?
There is no support for USB network devices at this time. Your only option for network access is wifi.
Why is physical network access a necessity? Is it a security issue, or do you just not have a wifi access point nearby? If the latter, you can always purchase a mini wifi access point to connect to your ethernet cable, and then just use it in bridged mode.
Sometimes i need test a particular wired connection or maybe i need to configure a network device that doesnt have wireless access, etc.
As long as you configure it properly, you should be able to reliably test network connections and configure devices from a mini wifi access point, since it will basically pretend like your Transformer is physically connected on the same segment. It's a bit of a roundabout way to do it, but it's your only solution until USB network adapters are supported.
Edit: I forgot to mention a suggestion for a mini wifi access point. My favorite is the D-Link DAP-1350.
I'm pretty sure you can get miniature 'bridge' devices that plug into ethernet and present themselves as a mini access point via WiFi (The original xbox wireless adapter is basically this)
That way you can use the on board WiFi to connect to an ethernet network.
PhonicUK said:
I'm pretty sure you can get miniature 'bridge' devices that plug into ethernet and present themselves as a mini access point via WiFi (The original xbox wireless adapter is basically this)
That way you can use the on board WiFi to connect to an ethernet network.
Click to expand...
Click to collapse
I have recently bought a device like you suggest here. Sapido RB-1602. It is quite small, and even better it can be powered by the Transformer usb port.
bridges can be a pain to work with, especially when the entire point of connecting to the wired connection was to troubleshoot it. Also, if I have to carry around something that large, i might as well have a laptop.
I'd be interested in this also. We can't have wireless at work, and I'd like to get internet on it.
This is on my list of to-dos, I have the same needs as the OP.
Kwjake said:
I'd be interested in this also. We can't have wireless at work, and I'd like to get internet on it.
Click to expand...
Click to collapse
How is the network setup at the office? If there are no mac addy filtering or domain login requirement to obtain or use an IP you can setup your own wifi just don't broadcast the SSID. But if your admin has alerts setup for unknow devices using IP's they will shut it down or block it.
There are other android devices that use ethernet adapters so it can be done
http://www.androidtablets.net/forum...blets/942-usb-enthernet-cable-connection.html
How about bluetooth to ethernet?
http://www.geekzone.co.nz/content.asp?contentid=1773
Here you go. Now is there support in Honeycomb for it?
http://www.euogo.com/usb-lan-adapte...to-rj45-adapter-for-android-tablets_p420.html
Sorry for all the posts but I'm getting hits so ...
This looks like the same thing as above but on amazon
http://www.amazon.com/AGILER-RJ45-ADAPTER-NETWORK-COMPUTER/dp/B000BL3M3U
Ordered one, for less than $5 worth a try.
DevCake said:
Sorry for all the posts but I'm getting hits so ...
This looks like the same thing as above but on amazon
http://www.amazon.com/AGILER-RJ45-ADAPTER-NETWORK-COMPUTER/dp/B000BL3M3U
Click to expand...
Click to collapse
The important comment from the Amazon thread on that item is:
dm9601 chipset. Supported on Linux, but only very recent versions (2.6.21 or later).
Unfortunately not supported by the version of Linux included in latest Debian GNU/Linux release.
Click to expand...
Click to collapse
So if you take the Linux kernel being used by the Honeycomb branch of Android, and recompile it to include this driver from the Linux trunk, maybe you could get it to recognize the device and "just work".
Maybe.
jmbneaf said:
Ordered one, for less than $5 worth a try.
Click to expand...
Click to collapse
bump...did u give it a try?
DevCake said:
How is the network setup at the office? If there are no mac addy filtering or domain login requirement to obtain or use an IP you can setup your own wifi just don't broadcast the SSID. But if your admin has alerts setup for unknow devices using IP's they will shut it down or block it.
Click to expand...
Click to collapse
I am the admin . We have an outside agency that scans for wireless (ssid or not).
ayman07 said:
bump...did u give it a try?
Click to expand...
Click to collapse
yup - not recognized. If someone knew the kernel (updated it) & could get it to me, I would gladly try it.
~J
me too. similar situation.
Related
This could possibly qualify as one of those non-existant stupid questions - but I wonder if I could use the XDA with a serial cable to connect to the console port of say a management switch or router, using some kind of terminal emulation software?
.wey
Could you do this with the following adapter?
http://pc-mobile.net/pxsm.jpg
Good Idea, Hope someone responds with a positive solution!
That's the solution. Simple as that. Serial cable. Depending on the way it's wired you may need a null modem adapter in addition. Then just fire up any terminal software on the PPC, set it for 9600 N,8,1, and you are on.
I've been carrying around base scripts for routers on a handheld for over 10 years so I can config a new router or restore an existing one in seconds. With Cisco IOS this is easy; not sure how well it would work for others, don't know them.
Raptor said:
Could you do this with the following adapter?
Click to expand...
Click to collapse
Cable would need to be longer or you will have a bunch of disgruntled network engineers 8)
Don't have WiFi where I am, but I do have internet on my computer, is there any way to hook up my phone via USB and use my computer's connection on my Note?
Buy a cheap wifu router, and add wifi to whatever hard connection u have, unless u have a USB cell modem on ur PC. Even then thay make routers for types as well...
I don't have any use for this, but being a network engineer, I was curious about it. A quick google came up with this, which you might be able to at least use as a starting point...
http://forum.xda-developers.com/showthread.php?t=1371345
Synner12 said:
I don't have any use for this, but being a network engineer, I was curious about it. A quick google came up with this, which you might be able to at least use as a starting point...
http://forum.xda-developers.com/showthread.php?t=1371345
Click to expand...
Click to collapse
I saw that, but was hoping for an easy non-rooted method.
I'll have WiFi later today, I'll just wait.
How hard would it be to get something like this to work with the Rezound?
I know with the Galaxy Nexus you can plug a microUSB to USB adapter in and use flash drives and external hard drives if you're using the right kernel.
I'm wanting something like this because it would be nice to plug into the network at work and ping printers and stuff like that with my phone instead of finding a computer and logging in.
http://www.newegg.com/Product/Product.aspx?Item=N82E16812196235
Not in Gingerbread
USB host mode is only supported in Honeycomb or above, so this won't be possible without ICS on this phone.
I'm not sure if anyone has made an ICS kernel that supports USB host mode.
Also, in addition to compatible software, the phone also needs compatible hardware, which the Rezound might not have.
If you don't have wireless access buy an airport express.
wlmeng11 said:
USB host mode is only supported in Honeycomb or above, so this won't be possible without ICS on this phone.
I'm not sure if anyone has made an ICS kernel that supports USB host mode.
Also, in addition to compatible software, the phone also needs compatible hardware, which the Rezound might not have.
Click to expand...
Click to collapse
Thanks for your input
GrayTheWolf said:
If you don't have wireless access buy an airport express.
Click to expand...
Click to collapse
And this would defeat the purpose completely.
circa881 said:
Thanks for your input
Click to expand...
Click to collapse
Apparently Chainfire tested a bunch of devices and listed the Rezound as incompatible.
http://usbhost.chainfire.eu/
He tested both Gingerbread and ICS, and none of them worked.
(Although those are all probably stock or modified Sense kernels, so maybe there's hope for AOSP? )
circa881 said:
And this would defeat the purpose completely.
Click to expand...
Click to collapse
How?
He said USB to Ethernet. Apparently he only has a hard wire connection. So, buy an airport express to make that hardwire wireless.
GrayTheWolf said:
How?
He said USB to Ethernet. Apparently he only has a hard wire connection. So, buy an airport express to make that hardwire wireless.
Click to expand...
Click to collapse
It doesn't totally defeat the purpose, but considerably complicates things. I'd sooner carry a laptop than break out a wireless router, fire it up, make sure it won't interfere with anything on the wired or wireless side (could be tough to do if you have to log in wireless), then ping/ssh/<your-protocol-here> through that device to get to the device I'm looking for.
With a USB dongle, plug it into the phone, into the wall, and do what you need to do.
Yeah the USB thing would be nice.
You are over complicating the router. Most routers are plug and play nowadays so Ethernet into existing network, and power is all you need with wireless freedom.
It would be even more to carry with me and more money than I'm willing to spend. I was just curious to know how hard it would be to plug my phone straight into the network so I can ping printers or telnet into stuff at work
circa881 said:
It would be even more to carry with me and more money than I'm willing to spend. I was just curious to know how hard it would be to plug my phone straight into the network so I can ping printers or telnet into stuff at work
Click to expand...
Click to collapse
Ethernet word be nice, but it doesn't exist. I was just providing an alternative.
I would be careful about plugging things into the work network. Some IT managers are rather...protective of their domains and set up extensive security, to the point where the particular port you plug into may shut down if it recognizes an unauthorized device. I work for the Marine Corps, and aside from the fact it's a punishable offense to connect an unauthorized device to the Navy/Marine Corps Intranet (and attached information systems), the switches will immediately disable a port with an unrecognized device connected.
Hi fellow owners,
I am considering to buy, but I'd prefer to be a cheap and get the 16GB WiFi version. However, it would be nice to be able to use a USB dongle for 3G from time to time. Anybody tried?
Thanks!
gfdsaorg said:
Hi fellow owners,
I am considering to buy, but I'd prefer to be a cheap and get the 16GB WiFi version. However, it would be nice to be able to use a USB dongle for 3G from time to time. Anybody tried?
Thanks!
Click to expand...
Click to collapse
Its micro usb port, will have to use adapter, my advice, use your phone as host spot
BADBOY1412 said:
Its micro usb port, will have to use adapter, my advice, use your phone as host spot
Click to expand...
Click to collapse
good advice. I can certainly do this as well as use a 3g wifi router i have. but using the phone's hot spot drains phone's battery and using a router adds to the bulk. that is why I'd like to try a dongle.
Thanks!
Xperia Link
gfdsaorg said:
good advice. I can certainly do this as well as use a 3g wifi router i have. but using the phone's hot spot drains phone's battery and using a router adds to the bulk. that is why I'd like to try a dongle.
Thanks!
Click to expand...
Click to collapse
I read in the GSMArena review that the XTZ can be tethered to a phone using Bluetooth:
Even if you get a Tablet Z without 3G, you can still use mobile Internet, provided you have a data plan on your droid phone and the Xperia Link installed. The app simplifies the tethering process. It puts a widget on the homescreen that lets you turn tethering on and off.
You might be thinking that you can just use your droid's Wi-Fi hotspot feature to do the same (and you could). The difference here is that Xperia Link uses Bluetooth to share the Internet connection and not Wi-Fi. This should be more power efficient than a Wi-Fi hotspot especially considering you can keep Bluetooth on all the time, which will let tablet and phone hook up automatically once they are close enough (you can't do that with a hotspot as your battery will be dead in a couple of hours).
Click to expand...
Click to collapse
I haven't been able to try that yet -- my pre-ordered XTZ has yet to ship -- with my Nexus 4 but it could be a solution to Wifi Hotspot battery drain issue.
-- Edit to add --
Well, found the official Sony Xperia Link in the Google Play Store and it's incompatible with non-Xperia phones apparently. Although, the Bluetooth-tether idea still sounds promising. Is there a way to get around the Sony lock-in?
Works!
So I've got the tablet this week and tried just now to stick the USB modem into it.
Naturally you have to be rooted, then you need a dialer :
PPP Widget
from the author of usb_modeswitch (ubiquitous linux tool to change the usb modems from CD to serial mode)
then you need the usb drivers unsurprisingly missing from the stock rom:
On author's forum
then insmod the modules in the zip file:
cdc-acm.ko
usb_wwan.ko
option.ko
(option requires usb_wwan to be loaded first), drop the widget on the home, it should do its magic and ask you for the APN. Then it works.
what a joy.
p.s. apparently the dongle I have needs more power than there is on the tablet port, so you need a powered hub (clumsy) or an external battery and a Y cable to power it.
I've been toying with the idea of getting a micro USB cable with the other end being an HDMI to connect to my computer monitor or TV for easy plug and play. I see there are several versions of cables. Some have 2 ends (Micro/HDMI), while others have 3 ends (Micro/USB/HDMI). I presume the 3 end with the USB is for charging.
Does anyone currently use one for the Nexus 6 that is working that they recommend ? Does it matter if I buy one without the USB end ? Thanks
Sadly, the Nexus 6 does not support HDMI out. Those cables you've come across are for other devices.
To answer your question: often, the ones with three ends need to be plugged into a USB charger to work because there is circuitry requiring power inside the cable - in my experience, these cables do not charge the phone despite requiring the power brick.
etherfish said:
Sadly, the Nexus 6 does not support HDMI out. Those cables you've come across are for other devices.
To answer your question: often, the ones with three ends need to be plugged into a USB charger to work because there is circuitry requiring power inside the cable - in my experience, these cables do not charge the phone despite requiring the power brick.
Click to expand...
Click to collapse
Thanks for the info. I noticed they worked for other phones, but I didn't see any on the Nexus 6 so that's why I was curious
mikeprius said:
Thanks for the info. I noticed they worked for other phones, but I didn't see any on the Nexus 6 so that's why I was curious
Click to expand...
Click to collapse
The way people get around it is using a chromecast. If you feel it's worth the investment you could do that.
TriguyRN said:
The way people get around it is using a chromecast. If you feel it's worth the investment you could do that.
Click to expand...
Click to collapse
Or if your rooted any miracast device. there are a couple threads around about just that and the different devices.
TriguyRN said:
The way people get around it is using a chromecast. If you feel it's worth the investment you could do that.
Click to expand...
Click to collapse
Can Chromecase be used without an internet connection ? I can wifi hotspot my cellphone. My big thing is I don't always have access to internet,
mikeprius said:
Can Chromecase be used without an internet connection ? I can wifi hotspot my cellphone. My big thing is I don't always have access to internet,
Click to expand...
Click to collapse
I'm really not completely clear on that. From my understanding it needs to at least be connected to a hotspot off your phone but, I am unsure if it requires internet. I don't personally own one so I'm not sure, sorry man.
You can hotspot from your cell but it eats up data pretty good and you can't hotspot and stream at the same time so you'd have to have 2 devices one to hotspot an one to stream but it works keeping in mind it won't be the fastest most reliable.... But in my opinion a chromecast is a pretty good investment....
vysors my personal favorite
https://chrome.google.com/webstore/detail/vysor-beta/gidgenkbbabolejbgbpnhbimgjbffefm?hl=en-US
works great on xubuntu all u need is a usb cable
Masterloki666 said:
You can hotspot from your cell but it eats up data pretty good and you can't hotspot and stream at the same time so you'd have to have 2 devices one to hotspot an one to stream but it works keeping in mind it won't be the fastest most reliable.... But in my opinion a chromecast is a pretty good investment....
Click to expand...
Click to collapse
This doesn't sound right...
If he has no access to internet, and wants to stream from his phone to his chromecast he is likely wanting to stream local data to it, and that shouldn't use any data from his cell plan as it would basically be local connection just using the phones access point instead of having a router in between.
You can definitely run a hot spot and network with devices connected to it locally. You can run hotspot and turn off your data to just create a local network.
Not sure why you are saying he would need two devices? Not sure why you would say it would eat any more data, it wouldn't use any more data to cast netflix to his monitor then it would to stream netflix in the first place on his phone?
scryan said:
This doesn't sound right...
If he has no access to internet, and wants to stream from his phone to his chromecast he is likely wanting to stream local data to it, and that shouldn't use any data from his cell plan as it would basically be local connection just using the phones access point instead of having a router in between.
You can definitely run a hot spot and network with devices connected to it locally. You can run hotspot and turn off your data to just create a local network.
Not sure why you are saying he would need two devices? Not sure why you would say it would eat any more data, it wouldn't use any more data to cast netflix to his monitor then it would to stream netflix in the first place on his phone?
Click to expand...
Click to collapse
Pretty sure he means if you want to use primary phone as hotspot, you need a second device to do the casting. As far as data connection, I'm reasonably certain that chromecast uses desktop style data, not mobile data. Meaning, it uses more data then directly on the phone, as the phone becomes a remote, not the actual device that does the streaming.
Hope that makes sense.
Thanks for the info everyone. I'm going to pick up a chromecast however I will just have to make sure when I use it I have a WiFi connection as well. I wasn't sure if you could only use the phone as a Hotspot and that's it
I'm pretty sure you can... The cromecast stuff just looks for a Chromecast on your local network, I'm not sure why people think your phone wouldn't be on its own network.
Never tried it with a Chromecast, but I have ran other local network stuff by attaching to my phones hotspot.
Give it a try when you get it and post back here to let us know, because I don't think any of us ACTUALLY know, but I am almost positive it will work.
I have a chromecast but I've never gotten it working without connecting to a seperate wifi source (not my phone's hotspot) but it could very well be possible.
I do want to comment that with the chromecast being wireless, some people might experience some lag. My solution this was to buy a wired adapter for the chromecast in addition to a micro usb to ethernet that worked with my phone. Both ethernet cables hook into my router and I can effectively mirror my device wired. Obviously there is probably still some lag, but is now below the threshold that I can perceive.
I have tried this you either need two devices or WiFi.
DR3W5K1 said:
I have tried this you either need two devices or WiFi.
Click to expand...
Click to collapse
For some reason it will not recognize the phone as a local network or router