Hello everyone
I own an HTC Star100 and have been using it in India for last 4 years without any problem, however few months back, it stopped recognizing any SIM, and says "No SIM" or SIM not recognized.
After that I installed many of the ROMs available on this website in different threads. All of them get installed properly and work great, but still SIM cant be recognized.
Please help, because I like this phone, even though I have a few other sets. Is this a hardware error (which i doubt, as many other have faced similar problem as i found on google) or the SIM has been locked?
Any help from the great fellow netizens and developers out there would be greatly appreciated.
umangsagar said:
Hello everyone
I own an HTC Star100 and have been using it in India for last 4 years without any problem, however few months back, it stopped recognizing any SIM, and says "No SIM" or SIM not recognized.
After that I installed many of the ROMs available on this website in different threads. All of them get installed properly and work great, but still SIM cant be recognized.
Please help, because I like this phone, even though I have a few other sets. Is this a hardware error (which i doubt, as many other have faced similar problem as i found on google) or the SIM has been locked?
Any help from the great fellow netizens and developers out there would be greatly appreciated.
Click to expand...
Click to collapse
use SIM UNLOCK, perhaps with the device will recognize your SIM card
if still not recognized check that the SIM holder in the device
Dear sir,
I have followed the method, and i am able to follow the steps and get my phone application unlocked using SDA_ApplicationUnlock.exe
After that I ran the simlock.bat which opened a Command Prompt screen and showed the following lines but I am still unable to find any network, it either says Phone off or keeps on searching, i have used this phone for 3 years and am facing this for last one month, in between it worked for a day but again same problem :
-----------------------------------------------------------------------------
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>REM
Read simlock data from Startrek
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>REM
Phone must be application unlocked !!
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>REM
Run SDA_ApplicationUnlock first and restart phone
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>mkdi
r 1
A subdirectory or file 1 already exists.
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>REM
cecopy SurrealNetworksAppUnlock.cab dev:\
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>REM
prun SurrealNetworksAppUnlock.cab
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>pmem
dump -a 0xB002709C 16 1\docid.bin
CopyProcessMemoryToFile(00000042, b002709c, 00000010, 1\docid.bin)
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>pdoc
read -n 1 0x000000 0x20000 -b 0x4000 1\simlock.bin
CopyTFFSToFile(0x0, 0x20000, 1\simlock.bin)
ERROR: ITReadDisk : read 00004000 bytes - Data error (cyclic redundancy check).
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>echo
"simlock data written to file in subdirectory 1"
"simlock data written to file in subdirectory 1"
C:\Documents and Settings\UTI\My Documents\Downloads\Compressed\Simlock-kit>paus
e "press return to exit"
Press any key to continue . . .
-----------------------------------------------------------------------------
Please Help
Related
i have a O2 XDA II . it came loaded with 1.66WWE. i wanted to put 1.60. i downloaded it from sourceo2.com
then double clicked the installable. it started the downgrade . it said it will take 30mins & started deleted the rom image.. i then went for lunch & came back in 15mins.. the phones now totally dead.
If i dock it , the screen says USB V1.06
if i remove it the screen says Serial V1.06. I cant hard rest it nor can i soft reset it. i huess cause there no rom image in it.
What do i do.. please help with as many links software as one can..
Please...
ive got 1.72, but when i try that. it says country error.??
can that be resolved.. i dont mind loading 1.72.
the good news is that it seems you still have the boot loader working ... use ER2003 tool to modify the country code of the 1.72 ROM file ... or you can use the xda2nbftool.exe if you like the command line mode
thakns, but i have the 1.72 as an exe file. can i use er2003 to edit the file ??
hyper said:
thakns, but i have the 1.72 as an exe file. can i use er2003 to edit the file ??
Click to expand...
Click to collapse
Unpack the .exe file with winrar/winzip. And you're good to go.
Edit this file: ms_.nbf
managed to unpack it... now when i try to load 1.60 it says model id error & if i try to load 1.72 it says country id error.
what do i change in the ms_.nbf file ????
do i only change this file fields or all three??
i even removed the battery & checked the model ID. on my phone it says PH10B
i changed all the three files to PH10B ..
Now i get Connection Error.....
Now what???
now the error is ERROR 101... connection error.
(i'm loading 1.60)
also is it possible for me to do it via my emory card (i have a MMC32MB & 128MB)
if so, what file do i need to copy & then whats the procedure??
i got 1.03.00 rom on mine. my xda 2 is 2 days old now dunno wht rom to load it up with now. whts the best & safe rom now. i have no apps or nething to back up so its oki. the phone was bought from u.k. and was locked on O2 network. now its unlocked and being used in India. plz advise wht ROM to d/n and use. if possible the d/n link as well. thx
Question?
Why do you want to downgrade your phone? :shock:
For upgrade to 1.72:
1. Download i-mate 1.72 update and xda2nbftool
2. unpack that update to any directory on your harddrive
3. download script from this post to created directory (unpack it too)
4. copy xda2nbftool.exe to that directory
5. run provided script
6. insert XDA2 to cradle and then HimaUpgradeUt.exe
You will i-mate splash screen from i-mate though, but working device.
thanks for all the help. but im yet getting country ID error even after running the process .
this process basically converts the id to O2, in a batch dos mode... right??
then y is the problem yet there.
i wonder... most O2 XDA II come with 1.6 rom version. mine came with 1.66. could that mean its not O2 even though its written O2 on my phone? could it mean its T-Mobile or something??
can someone post a link or software that i need to put onto my MMC card & then use that to install the rom from the card inserted in the phone??
hyper said:
thanks for all the help. but im yet getting country ID error even after running the process .
this process basically converts the id to O2, in a batch dos mode... right??
then y is the problem yet there.
Click to expand...
Click to collapse
So, what's that problem? Can you run it?
Try to run it in command prompt... And if it writes any error, post it here...
Can you access the file system of your XDA2 from ActiveSync -> Explore?
now i managed to get the problem of Country error out of the way , but now im getting the ERROR 101 - Connection Error.
no i cannot browse any files & my active sync does not show connected.
what files do i need to copy paste onto my MMC card so that i can flash it by executing the files with the camera button & the MMC Card inserted??
im dowloading the NTRW & 1.72 NK.nb1 file. do i just copy & paste it on the mmc card & then instert the card into the phone & then press the camera button.. should this do the trick??
this is all that i have tried so far... yet no luck.
my phones originally from malaysia , its an O2 XDA II
i have the following rom with me. my bootloader is V1.06
1. RUU172800WWE_CDL_SKU1
2. XDA_IIupgrade_v16050
3. RUU172104wwe-t-mobile-uk
1. i removed the battery , dcoked the phone, connected the charger to the docking bay at the back...the red light on the phone lights up.... the bootloader screen shows up ina slightly distorted manner.
i then ran all the three roms as it is..without editing anthing. The error i get in all the three times is ERROR 101. CONNECTION ERROR. it tells me to check is usb is connected, charger is connected usb port is conencted & the phone is on. .......... everythings connected but obviously phone can only be in bootloader mode.
2. i put the battery back in dock the phone, the charger is yet connected to the back of the docking bay. .. i try all three installations withour extracting or editing as they are exe files..... now, all the three times i get COUNTRY ID ERROR OR MODEL ID ERROR.
3. when i edit the ones that give me model id error then i get CONNECTION ERROR AGAIN. (this is again with the battery in & charger plugged in)
i downloaded the NTRW & 1.72 NK.nb1 file. but the one that is available on this forum is corrupted. so i cannot extract it.
NTRW ive downloaded seperately. i need the nb1 file now. can someone post a working, no-corrupted image rom image file?
once i get the correct Rom.nb1 file... all i have to do it copy & paste the correct rom.nb1 & ntrw.exe file onto my MMC card & keep the battery in the phone & insert the MMC card & press the Camera button .... is that correct? i'm guessing that this will run the ntrw exe file & load (dump) the Rom.nb1 file onto the phone. is that correct?
please do let me know what else i can try & dowload a newer RUU or something. i think the best way is to SD flash the phone.
i dont even mind flashing it to a PPC2002 version & then upgrading it from there. if thats possible.
As far as the connection between the USB Docking Bay is concerned,...everytim i connect or disconnect the phone, i hear the familiar XP "TING" which shows that some USB thing is connected, but my active sync does not show that the phones connected, i guess that cause it got no rom in it.
Also when i edit the ms_ / NK / Rom files er2003 i get an error everytime i start the software, but i just press IGNORE & continue. i always get ROM successfully written & then the error pops up again but i keep pressing ignore. this works... but whats up with the CONNECTION ERROR. IF ITS NOT CONNECTING TO THE PHONE, HOW DOES IT KNOW THAT THE MODEL ID OR COUNTRY ID WRONG ???
Ok.
If any ROM update can detect your device (as we can see error messages COUNTRY ID ERROR or MODEL ID ERROR), there is hope, you can update your device.
If it's 1.72 ROM (that writes COUNTRY ID ERROR or MODEL ID ERROR), use the solution I send you few posts ago (unpacking, running batch script etc.)
When you updating, keep battery in your device and charger of device connected to cradle! Don't remove anything.
BTW: Don't use RUU172800WWE_CDL_SKU1 update, it just update only part of your device (ExtROM)!
BTW2: Read this: http://wiki.xda-developers.com/wiki/HimalayaRomFlashing
thanks againa beecher. the problem is that once i use the patch & then run it. it does not show me the country id or model id error (for which i thank you) but then it says error connecting.
i have a USB to serial connector. should i try serial connection?? or maybe try it on another computer.
can anyone please tell me how do to a SD flash step by step with the Rom.nb1 file attachment of link.
I am trying to capture the unlock of my M3100 to help the forum.
I followed the directions below...
fun_key said:
What you need befor you start:
USBMON (I used the trial): http://www.hhdsoftware.com/usbmon.html
A win 2k/XP computer with admin rights
How to fool the IMEI-CRACK tool:
-Login with the administrator and setup USBMON
-Create with the administrator a user (named wathever you like) with only "user" or "powered user" rights
-Log in with the user you just created (you may have to resetup Active sync with this user; I don't know why but it seems that active sync doesnt setup for all user)
-Right click on the USBMON icon and select "run as"; input the administrator credential and configure the software ready for the capture
-Launch the crack and follow the instruction
And voila ! The dump should be achieved by now
Click to expand...
Click to collapse
I had to create another admin account as the unlock UTIL requires that you use the Admin account. I have been able to RUN USBMON while starting the unlock and it put the M3100 in the white unlock screen but then get an error and the util has shut down.
Any Ideas? I don't mind waiting to unlock so I help th community out...
OK...I think I captured it....The unlocked changes to a different driver type in the middle of the unlock. So I started a new session with the "NEW" device I think I captured it all but what do I do with this file now?
slimsaturn said:
OK...I think I captured it....The unlocked changes to a different driver type in the middle of the unlock. So I started a new session with the "NEW" device I think I captured it all but what do I do with this file now?
Click to expand...
Click to collapse
attach it here
Alright...POF They are too big to attach....Anywhere else I can throw them? If someone tells me how to upload them to the FTP I will do ASAP...Hopefully this is able to help someone. If I did miss the crucial info i am sorry for failing
no problem, i'm sure it will be juicy
Put them here:
ftp://xdaupload:[email protected]/Hermes/
USERNAME: xdaupload
PASSWORD: xda
let me know when the files are uploaded.
OK so I am getting a 530 Permission Denied error. Can i just email them or someone let me know what I am doing wrong
Email them to me.
sexy [email protected] vijay555.com
V
Finally the files are here:
ftp://xda:[email protected]/Hermes/Technical/unlocker-capture.zip
Going to have a look at them right now! will post something later
pof said:
Finally the files are here:
ftp://xda:[email protected]/Hermes/Technical/unlocker-capture.zip
Going to have a look at them right now! will post something later
Click to expand...
Click to collapse
Good Deal...hopefully this helps us
Slimsaturn!! You got it right
This is more or less what the unlocker does, will explain it in another post:
Code:
retuoR
USB> shmsg 8 2 "unlocking..."
USB> rtask a
[COLOR="Red"]Enter Radio Bootloader[/COLOR]
USB> rpass
HTCS-[url=http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoaderPassword]dyamic password[/url]-HTCE
...
USB> rversion
[COLOR="Red"]0106[/COLOR]
rrbmc x 6D0000 8000
rwdata 4D0000 800
[HTCS]- code, to big to paste here -[HTCE]
retuoR
USB> rtask b
[COLOR="Red"]Enter radio Image
AT-Command interpeter ready[/COLOR]
[email protected]=0,1,22051978
[email protected]=0,2,22051978
[email protected]=0,4,22051978
[email protected]=0,8,22051978
[email protected]=0,16,22051978
[email protected]=0,32,22051978
AT
retuoR
USB> shmsg 8 2 " done"
USB> task 8
Is that from what I sent you
slimsaturn, yes this has been taken from the files you posted (Thanks!).
Here is the process explained, if you don't understand anything check the wiki bootloader page for a better explanation.
Code:
retuoR
Returns from radio bootloader to normal bootloader, probably here because the capture was not started at the very begining of the unlocker process
Code:
USB> shmsg 8 2 "unlocking..."
USB> rtask a
[COLOR="Red"]Enter Radio Bootloader[/COLOR]
Shows "unlocking..." on hermes screen, enters radio bootloader
Code:
USB> rpass
HTCS-[url=http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoaderPassword]dyamic password[/url]-HTCE
Sends "rpass \r" (mind the space between rpass and \r), then sends "HTCS" + the password + the CRC of the password as bytes + "HTCE".
This authenticates to the radio bootloader (to be able to use the rrbmc command later), the password is dynamic (but the method to generate it is known) and sent encapsulated on a HTCS+password+CRC+HTCE block.
It should either return "T " for succes, or "F " for failure (encapsulated in the HTCSHTCE block), in the capture it returns "T".
Code:
USB> rversion
[COLOR="Red"]0106[/COLOR]
returns radio version encapsulated in HTCS HTCE block.
Code:
rrbmc x 6D0000 8000
Read back 32768 bytes (0x8000) of memory content from address 6D0000 and save the data to a file named "x".
@slimsaturn: do you have a file named "x" on your computer? can you send it too? if not, can you try to "undelete" it with some tool...?
Code:
rwdata 4D0000 800
[HTCS]+(2048 bytes of code, to big to paste here)+(4 bytes crc)+[HTCE]
This writes 2048 bytes (0x800) of data to address 4D0000, the data is sent encapsulated on HTCSHTCE block as well. I guess this does the CID unlocking.
These 2048 bytes are on the attachment, if anyone wants to look at (hint: compare it with extracted radios using an hex editor).
Code:
retuoR
USB> rtask b
[COLOR="Red"]Enter radio Image
AT-Command interpeter ready[/COLOR]
Returns from radio bootloader to normal bootloader, then enters the AT command interpreter to talk to GSM AT cmd interface.
Code:
[email protected]=0,1,22051978
[email protected]=0,2,22051978
[email protected]=0,4,22051978
[email protected]=0,8,22051978
[email protected]=0,16,22051978
[email protected]=0,32,22051978
This enters the same sim unlock code to all locking facilities (2,4,8,16,32). The code here is 22051978, I guess this code is calculated from what has been previously read by rrbmc command. Will be a different code on every device. Weird that it doesn't get the locked facility first, it just tries all them.
Code:
retuoR
USB> shmsg 8 2 " done"
USB> task 8
This exits from the AT command interpreter, shows "done" on the Hermes screen and reboots the device.
Now I'm going to try the 'rrbmc' command on my hermes and see what is read from there... I've also found that the content written to device by rwdata has some strings in common on GSM.nb (radio) extracted from NBH update, so it's part of the radio.
pof said:
@slimsaturn: do you have a file named "x" on your computer? can you send it too? if not, can you try to "undelete" it with some tool...?
Click to expand...
Click to collapse
Sure...I will check my recycling BIN tonight. If I can't find it there do you have utility that I can use to search my PC to try to locate it?
It will not be in the recycle bin, it will be either on the folder you run the unlocker from, or on the c:\temp c:\windows\temp
The exact size of the file is 32768 bytes, it is named "x" (without extension).
If the unlocker has removed the file (most probably) then it will be removed (but not in the recycle bin!) so you will need to use some software to undelete removed files, I don't know any but google may help.
Pof, I just tried running the unlocker with file i/o monitoring, and didn't see it produce a file called X (or anything else that looked like a likely candidate)
Maybe we can do a before and after dump of the radio patch - it'll probably be using a similar idea to the Universal unlocker if it's overwriting the radio.
V
pof said:
It will not be in the recycle bin, it will be either on the folder you run the unlocker from, or on the c:\temp c:\windows\temp
The exact size of the file is 32768 bytes, it is named "x" (without extension).
If the unlocker has removed the file (most probably) then it will be removed (but not in the recycle bin!) so you will need to use some software to undelete removed files, I don't know any but google may help.
Click to expand...
Click to collapse
Alright I will check tonight. I am guessing this is the missing link to fully understand what happens.
help needed
I need the help from someone who hasn't unlocked their phone yet and is willing to pay imei-check the 20GBP: I need to compare two regions of the radio before and after running the unlocker.
These are the steps to follow:
1) Disable activesync on your computer by right click on activesync icon -> connection settings -> uncheck "allow USB connections".
2) Put your device in BootLoader mode
3) Connect device to computer using USB cable.
4) Download TryBootloader.exe and run it.
5) TryBootloader fails most times you run it with one of these errors:
"Could not enter bootloader mode" or "SetCommState failed Could not open device " you need to reset your device and put it in bootloader mode again, and keep trying until you get this (usually no more than 5 or 6 tries):
Code:
USB>info 3
password ~:0T4~~000~X~000
Entered advanced bootloader
rtask a
rtask a
Enter Radio Bootloader
rinfo
rpass
Retval:
T
Entered radio bootloader
6) Once TryBootloader successfully authenticates you, open mtty.exe and select "USB" port and click "OK", this time you will not get the usual "USB>" prompt because you will already be in radio bootloader, but this should give you an authenticated command line in radio bootloader where you have all commands enabled.
7) Start HHD USBMonitor.
8) File -> New session -> USB Monitor -> Select USB device where your phone is connected -> Check "request view" -> Finish
9) In the upper part there are two tabs: basic and complete. Click on "Complete".
10) Type these commands in mtty window (do not copy paste, type them!) please note that you will not get any output (echo) on the screen when typing because you are on radio bootloader:
Code:
[b]rrbmc a 6D0000 8000[/b]
You will see a lot of garbage in the mtty screen, don't worry... when it finishes, type the next command:
[b]rrbmc b 4D0000 800[/b]
You will see a lot of garbage in the mtty screen again, don't worry... when it finisheds, close mtty.
11) you should see all the USB traffic output on USB monitor window.
12) click on Edit -> Export and Save as type "ANSI Text files".
13) Save the file and zip it. Name it "dump-before-unlock.zip"
14) Enable USB connections on ActiveSync again, softreset your Hermes and make sure activesync icon is "green" again.
15) Run the imei check unlocker as normal, following their instructions.
16) Once your phone is unlocked, repeat steps 1 to 13 but this time name the file "dump-after-unlock.zip"
17) Post a comment here and attach the two files, if they are too big upload them to xda-developers ftp.
After that we'll have everything to start working on a free unlocker
PS: I am traveling from Spain to Germany tomorrow and will be 1 week "away" without internet connection, I hope someone will have uploaded the files when I come back!!!
Awesome on the Stick
slimsaturn said:
I am trying to capture the unlock of my M3100 to help the forum.
I followed the directions below...
I had to create another admin account as the unlock UTIL requires that you use the Admin account. I have been able to RUN USBMON while starting the unlock and it put the M3100 in the white unlock screen but then get an error and the util has shut down.
Any Ideas? I don't mind waiting to unlock so I help th community out...
Click to expand...
Click to collapse
Humm, interesting, when I tried it didn't required the admin rights so far. I tried this a quite long time ago, I may have forgot something or they may have updated there util.
@pof: You were talking about CID unlocking. I don't think that the IMEI tool is still able to make the tytn Super CID. I have used it about 2 months ago and my device is far from being super CID . Slimsaturn, could you please give us the CID of your device in order to check what really happen down there?
EDIT: I found the exe program when I tested the dump. There is now an updated version of the .exe on there website. I guess that it could be interesting to test differents version of the tool, in order to better understand what it realy does and how it does it.
I upload here the older version, it can maybe interest someone. I ll give more tries with the newest version, if it is able to handle my radio version.
nice work
my £20 donation is sitting here waiting for you guys!!!!!!!!!!
anything i can do to help?
information:
version rom:2.15.7.38 fre
i put a different SIM but code invalid!!
any help
As i can see in that photo, the program couldn't update the itsutils.dll
Maybe the path is too long....Just move the folder with the program to c:\ and ther try again.I think that's the cause of your problem.
pswnio said:
As i can see in that photo, the program couldn't update the itsutils.dll
Maybe the path is too long....Just move the folder with the program to c:\ and ther try again.I think that's the cause of your problem.
Click to expand...
Click to collapse
---------------
I Have a Qtek S200 (HTC Prophet) and it is SIMLOCKed to one GSM operator. Now i tried with Lokiwiz 03a for SIMUNLOCK.
But it is gave me same error. There is writing "Could not update itsutils.dll to the current version, maybe it is inuse?"
i try to insert the code and it doesnt work
Problem solved
Tried everything in all the threads, 2 different registy editors, paid imei-check £20!! for cid unlock, which unlocked an un-locked a sim un-locked phone. registry editor settings don't appear to stick, when i run pdocread.exe the black box appears then dis-appears 1 second later!! everytime i try update get 5% in then 270 error. SDA_ApplicationUnlock.exe fails!! It just ain't having it!! phone is a new from expansys, computer is running xp pro. i've done everything in the way decribed. any help would be great.
vo1968 said:
when i run pdocread.exe the black box appears then dis-appears 1 second later
Click to expand...
Click to collapse
You MUST run pdocread via Command Line. To launch command line you have to click on Start->Run->enter cmd.
Then move to folder where pdocread.exe located using cd command. In example: C:\>cd D:\itsutils\
thanks for that, i will try that tomorrow.
thanks Erofich, but it still ain't having it. the dosbox does display but when i run commands all i get is errors. error ITGetStoreMgrList, system cannot find file, invalid signature, WARNING could not find default device etc etc. I have phone activsynced, the itsutl as described, i even payed imei-check for cid unlock, which i ran & was "successful"!!!! still get error 270 on rom update. i've looked though all the threads again. i have flashed spv e100, xda, xda exec & mda compact 3 in the past, none have give me as much grief as this. ANYONE HELP??????
vo1968 said:
...the dosbox does display...
Click to expand...
Click to collapse
Dosbox? oO You have to run pdocread via Command Line (cmd.exe) and not a DosBox
And yes, you MUST make an application unlock before running any part of itsutils, search this StarTrek forum for that thread.
thanks, sorry i meant command line, like you said. got this error:
C:\Documents and Settings\vo>build\pdocread.exe
Copying C:\Documents and Settings\vo\build\itsutils.dll to WCE:\windows\itsutils
.dll
Could not update itsutils.dll to the current version, maybe it is inuse?
try restarting your device, or restart activesync
tried resetting & restarting, guess what? same issue. but it does appear to be getting nearer to running your rom, which everybody else is raving about. many thanks.
have you app unlocked your device?
Download regeditSTG2 which is digitally signed: http://4pda.ru/forum/attach/387522/regeditSTG2.zip
Then install it and change some registry values:
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 2
-> change to 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 16
-> change to 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 128
-> change to 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101a": Dword = 1
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101b": Dword = 1"
Click to expand...
Click to collapse
cheers. do i run that in the phone or the computer? i'll do it tomorrow, given up for today! sorry to be a total noob!
vo1968 said:
cheers. do i run that in the phone or the computer? i'll do it tomorrow, given up for today! sorry to be a total noob!
Click to expand...
Click to collapse
You must install regedit STG2 to smartphone and edit registry values via smartphone
Simply search for regeditSTG2 in Start(may be Accessories) after installing and run it
THANK YOU VERY MUCH. it has been a long week but wm6 is installed. couldn't have done it without you. thanks again.
Hello. I have a problem with unlocking my Ameo from Tmobile. I've unlocked my athena using Olipro "Athenaunlocker.exe" and it didnt work. I've tried the codes from "gsmliberty.com and it didnt work". I can put any Rom like Michyprima one, but my sim is still not recognized by a phone. Aswell i have a problem with camera. When i'm trying to turn it on it dont turn on and i have a message "Unable to initialize Camera"... I've tried SR and HR and it didnt helped. Any suggestions for my problem???
Kind Regards
AP
Have you tried a newest radio ROM?
May be something went wrong with radio and cooked ROMs haven't RADIO inside
No i have a radio 1.50
i will upgrade a radio then.thanks...
I've upgraded to 1.57
but still same problem... My sim dont work with my ameo...
But the other SIM works? If the answer is YES may be You have CID unlocked you phone but NOT SIM Unlocked
Read carefully the topic here http://forum.xda-developers.com/showthread.php?t=315831 download and try agin the OLIPRO Solution.
P.S. If it works don't forget to donate!
What i've realized is
the UK simcards dont work, but simcards from abroad they ok and when they go on, they using roaming from T Mobile... Here's a log file from my athenaunloker.exe
==Athena Debug Output==
==Made by Olipro - 2007. www.xda-developers.com====Deploying CAB Files==
Warning: no device connected.
Waiting for a device to connect...
Connected.
Syncing from <Cert_SPCS.cab> to <dev:\>
"Cert_SPCS.cab" Copying (New) ... 0/71 k 64/71 k 71/71 k ok
Warning: no device connected.
Waiting for a device to connect...
Connected.
Syncing from <EnableRapi.cab> to <dev:\>
"EnableRapi.cab" Copying (New) ... 0/70 k 64/70 k 70/70 k ok
Bad argument: dev:\Windows\
Usage: CeCopy [options] <Source_FileSpec> <Destination>
Options:
/is Include same files
/s Include subdirectories
Arguments:
Source_FileSpec File specification denoting the source of the copy.
Destination Where files should be copied to.
For the source, wild cards or directory names may be specifed, as may be single
files. The destination can be either a directory or a file name, depending
on the type of source specified.
By default, an argument is assumed to live on a local filesystem. To indicate
that either argument denotes a location on a device connected via ActiveSync,
prepend 'dev:' to that argument. To articulate that a local filesystem is
referenced, prepend 'desk:' to the argument.
Exiting.
==Installing CAB Files==
you may need to confirm installation on your device screen
==Backing up current SPL, DO NOT DISCONNECT OR TOUCH THE DEVICE==
Copying F:\TempAth\itsutils.dll to WCE:\windows\itsutils.dll
CopyTFFSToFile(0x0, 0x100000, SPL-backup.nb)
==Flashing your SPL, DO NOT DISCONNECT OR TOUCH THE DEVICE==
CopyFileToTFFS(SPL-Olipro.nb:0, 0, 00100000)
==Verifying the SPL, DO NOT DISCONNECT OR TOUCH THE DEVICE==
CopyTFFSToFile(0x0, 0x100000, SPL-verify.nb)
SPL Flashed Successfully!
==Patching Radio==
==Radio Patched! Now Unlocking!==
Warning: no device connected.
Waiting for a device to connect...
Connected.
Syncing from <athena_unlock.exe> to <dev:\>
"athena_unlock.exe" Copying (New) ... 0/288 k 64/288 k 128/288 k 192/288 k 256/288 k 288/288 k ok
==Restoring Radio==