Related
first five lines of the readme for the drivers
ASUS Android USB drivers for Windows
VID: 0B05
PID for fastboot: 4DAF
TF201:
PID for MTP: 4D00
PID for MTP + ADB: 4D01
PID for RNDIS: 4D02
PID for RNDIS + ADB: 4D03
adb reboot bootloader
this should put the device in fastboot mode.
Well you can't boot into the bootloader from adb. I tried the adb reboot bootloader and all it did was reboot the tablet. no bootloader nothing. And holding down both volume buttons and restarting doesn't do it either (like it does for other devices)
we have APX mode, which is the only bootloader mode we can access. unfortunately, NVFLASH hasn't been updated for Tegra 3 devices.. so we cannot use it
Found the mode to do a factory reset outside of the Honeycomb OS.
1- Shutdown the tablet
2- Hold the vol down while you hit the power button
3- Release both buttons and don't hit anything and it should take you to a screen with a flashing cursor on either the Android bot or the icon that says Wipe data.
4- Use the vol down to change between the 2 modes. Use the vol up to confirm your choice.
DO NOT CONFIRM TO WIPE YOUR DATA! I'm not responsible if you do. If you think that you just might have the bad luck and choice the wipe data by accident, don't even bother to go here.
unknown_owner said:
Found the mode to do a factory reset outside of the Honeycomb OS.
1- Shutdown the tablet
2- Hold the vol down while you hit the power button
3- Release both buttons and don't hit anything and it should take you to a screen with a flashing cursor on either the Android bot or the icon that says Wipe data.
4- Use the vol down to change between the 2 modes. Use the vol up to confirm your choice.
DO NOT CONFIRM TO WIPE YOUR DATA! I'm not responsible if you do. If you think that you just might have the bad luck and choice the wipe data by accident, don't even bother to go here.
Click to expand...
Click to collapse
good find. there is more to that mode.. im investigating as we speak
---------- Post added at 07:15 PM ---------- Previous post was at 07:12 PM ----------
There is a "recovery Kernel Image" Gives almost an exact look like the Samsung Recovery look
Hold Vol - and Power until screen shows...let go...Pres volume + within 5 seconds
--
It uses ADB PIDs, trying to force install drivers..
--
got it, NO elevated ADB response
I hope this is good news!
Sent from my PC36100 using Tapatalk
the recovery i found is meant for CWM if a dev decides to create CWM for the TP. As for now, i don't know... it looks for something then goes to a warning (!) screen. im wondering if its connecting to /sdcard/ and looking for a file for recovery or what.. hmmm
--thread apparently got moved. nice.
our only hope looks like NVFLASH for now.. but we need to find out the SBK for our device first and have it incorporated into NVFLASH so we can use it..the Android.Mobi are gonna have to do that :/
Hello XDA,
as I am kind of new to the android system, I would really need some help with an old android tablet of mine. Basically I just want to use it for games and stuff like that, maybe Facebook, nothing too intense.
As I somehow managed to forget my Pattern Lock, I'm not able to access it anymore. Although I searched a couple o forums about a hard reset/wipe/factory reset, nothing helped me yet. Just so you know, every possible button combination I found on this lovely Internet did NOT work for me (maybe I'm just doing something wrong, although I don't think so). Whatever I've tried, it just won't go into the recovery section.
I am talking here about the MPMAN 720 Android Tablet. I believe it came pre-installed with Android 2.0 or 2.2 but I'm not sure. I did not brick the device (if this is the correct designation) nor did I apply any custom ROM's or firmware's.
Full details are listed on the following web page: (I could not post the link, as I am a new member). Please go to google.com -> search for: mpman720 and click the first link(should contain mpmaneurope dot com)
Now, as I somehow have some knowledge about IT, I also was much of an iPod Touch user before, where I somehow came familiar to things like Jailbreaking or "Hacking" the device. So I wondered if there is any possibility to maybe wipe the whole tablet by using the computer, maybe to something I believe is called "adb". Although I have absolutely no idea of using "adb" or how to even start/open that specific command line. Oh, and also, very important, unfortunately USB-Debugging is not enabled (100% sure).
If there is any way you could assist me to wipe that horrible tablet and get back to the factory settings I once had I would be very thankful.
Thank you very much in advance and have a great day!
Cheers,
Richard.
Have you tried to reboot the tablet in recovery mode?? I know that evry android device can go in recovery mode by pressing Volume Up the Center button and the power button... keep holding them untill it turns on and when it does release the power button but NOT the other two.... it will eventualli turn on in recovery and there you will have to move using the volume buttons ( to go up and down) and the power button (to select) go down to wipe data/factort reset, select it, go down and select Yes
Sent from my GT-S5310 using XDA Premium 4 mobile app
---------- Post added at 02:37 PM ---------- Previous post was at 02:30 PM ----------
After the device is done it will be like as it just went out of the factory... sorry for my english.. i am italian
Sent from my GT-S5310 using XDA Premium 4 mobile app
Hello,
firstly, thank you for your quick response. Yes, I've tried that, and unfortunately it did not work. I just can't get that sh**** tablet to go into the recovery, no matter what I try. Also, there is an external reset button, which can be pressed using a pen for instance, but that does not do anything. All that the tablet is doing when I press some combinations is either nothing or rebooting. That's all.
Thank you again, hopefully someone can help with an advice.
Cheers,
Richard.
Your welcome.... sorry that i couldn't help you
Sent from my GT-S5310 using XDA Premium 4 mobile app
hard reset doesn't work
Hi, I also have mpman mp720 tablet with android 2.3.3. 720 mhz armv6 processor
Here's my problem:
i've tapped the reboot shortcut from the quickreboot app and then the tablet didn't start ( when it restarts the mpman logo appears then quickly dissappears .
I've tried to do factory reset : power+ volume up but the same , the logo appears and then dissappears , and the screen remains black with the back & menu led remain turned on
Can you please give me somen solutions?
Is the tablet modified ( rooted, custom rom, custom recovery),?
Sent from my GT-S5310 using XDA Premium 4 mobile app
leodani said:
Is the tablet modified ( rooted, custom rom, custom recovery),?
Sent from my GT-S5310 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
yes the tablet was rooted , but i really don't know what software method i've used( oneclik...something if i remember correctly )
L.E.: also i tried volume up + power + home , released the power and keep the home + volume up more than 30 sec . this time the logo doesn't appear anymore but the led from back and menu remain on . in addition now the screen is full black ( the method tried by me in the first post showed a black screen with a nuance of blue accentuated in the bottom of the screen ( landscape mode with the home button on the right ) )
You just need to hold VOLUME UP button for 10 seconds then you need to press POWER button (but keep pressed VOLUME UP) keep pressed that combination of keys until MPMAN logo shows. Then realise that buttons (don't press any other key) and for 5 seconds you will be in recovery mode.
I tried on mpman mpdc 702 tablet.
I hope i helped and sorry for my language.
Hi guys,
My step daughters tablet, the 7" Dual Core 4GB Trio Stealth G2 Hype, has frozen at the "Trio Stealth G2" logo boot screen. It won't go any further. I've tried every combination of key presses (pwr & vol+, pwr & vol-, pwr & vol-,vol+) to get it into recovery mode OR to hard reset it and nothing is working. I've tried hooking it up to my windows 7 computer, it shows up as M3-CHIP (only after I press pwr & vol-). I downloaded the android adt bundle like someone else suggested and then adding the hardware id of the device to the file called android_winusb.inf BUT that file doesn't exist anywhere within the adt bundle. I even just tried creating the file and adding the hardware id to the file I copied from another thread and when I click update driver and choose where that file is that I created it won't take, it says windows couldn't find a driver for this device.
Here's the file I created
Code:
;
; Android WinUsb driver installation.
;
[Version]
Signature = "$Windows NT$"
Class = AndroidUsbDeviceClass
ClassGuid = {3F966BD9-FA04-4ec5-991C-D326973B5128}
Provider = %ProviderName%
DriverVer = 08/11/2009,2.0.0010.00002
CatalogFile.NTx86 = androidwinusb86.cat
CatalogFile.NTamd64 = androidwinusba64.cat
;
; This section seems to be required for WinUsb driver installation.
; If this section is removed the installer will report an error
; "Required section not found in INF file".
;
[ClassInstall32]
Addreg = AndroidWinUsbClassReg
[AndroidWinUsbClassReg]
HKR,,,0,%ClassName%
HKR,,Icon,,-1
[Manufacturer]
%ProviderName% = Google, NTx86, NTamd64
[Google.NTx86]
;Orange San Francisco
%SingleAdbInterface% = USB_Install, USB\VID_19D2&PID_1354&MI_00
%CompositeAdbInterface% = USB_Install, USB\VID_19D2&PID_1354&MI_02
%SingleBootLoaderInterface% = USB_Install, USB\VID_18D1&PID_D00D
; HTC Dream
%SingleAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C01
%CompositeAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C02&MI_01
%SingleBootLoaderInterface% = USB_Install, USB\VID_0BB4&PID_0FFF
; HTC Magic
%CompositeAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C03&MI_01
;
;Moto Sholes
%SingleAdbInterface% = USB_Install, USB\VID_22B8&PID_41DB
%CompositeAdbInterface% = USB_Install, USB\VID_22B8&PID_41DB&MI_01
;
;TrioStealthG2Mine
%SingleAdbInterface% = USB_Install, USB\VID_1B8E&PID_C003&REV_0007
%CompositeAdbInterface% = USB_Install, USB\VID_1B8E&PID_C003&REV_0007
;TrioStealthG2
%SingleAdbInterface% = USB_Install, USB\VID_16D5&PID_8005&MI_01
%CompositeAdbInterface% = USB_Install, USB\VID_16D5&PID_8005&MI_01
;
;Google NexusOne
%SingleAdbInterface% = USB_Install, USB\VID_18D1&PID_0D02
%CompositeAdbInterface% = USB_Install, USB\VID_18D1&PID_0D02&MI_01
%SingleAdbInterface% = USB_Install, USB\VID_18D1&PID_4E11
%CompositeAdbInterface% = USB_Install, USB\VID_18D1&PID_4E12&MI_01
[Google.NTamd64]
;Orange San Francisco
%SingleAdbInterface% = USB_Install, USB\VID_19D2&PID_1354&MI_00
%CompositeAdbInterface% = USB_Install, USB\VID_19D2&PID_1354&MI_02
%SingleBootLoaderInterface% = USB_Install, USB\VID_18D1&PID_D00D
; HTC Dream
%SingleAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C01
%CompositeAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C02&MI_01
%SingleBootLoaderInterface% = USB_Install, USB\VID_0BB4&PID_0FFF
; HTC Magic
%CompositeAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C03&MI_01
;
;Moto Sholes
%SingleAdbInterface% = USB_Install, USB\VID_22B8&PID_41DB
%CompositeAdbInterface% = USB_Install, USB\VID_22B8&PID_41DB&MI_01
;
;Google NexusOne
%SingleAdbInterface% = USB_Install, USB\VID_18D1&PID_0D02
%CompositeAdbInterface% = USB_Install, USB\VID_18D1&PID_0D02&MI_01
%SingleAdbInterface% = USB_Install, USB\VID_18D1&PID_4E11
%CompositeAdbInterface% = USB_Install, USB\VID_18D1&PID_4E12&MI_01
[USB_Install]
Include = winusb.inf
Needs = WINUSB.NT
[USB_Install.Services]
Include = winusb.inf
AddService = WinUSB,0x00000002,WinUSB_ServiceInstall
[WinUSB_ServiceInstall]
DisplayName = %WinUSB_SvcDesc%
ServiceType = 1
StartType = 3
ErrorControl = 1
ServiceBinary = %12%\WinUSB.sys
[USB_Install.Wdf]
KmdfService = WINUSB, WinUSB_Install
[WinUSB_Install]
KmdfLibraryVersion = 1.7
[USB_Install.HW]
AddReg = Dev_AddReg
[Dev_AddReg]
HKR,,DeviceInterfaceGUIDs,0x10000,"{F72FE0D4-CBCB-407d-8814-9ED673D0DD6B}"
[USB_Install.CoInstallers]
AddReg = CoInstallers_AddReg
CopyFiles = CoInstallers_CopyFiles
[CoInstallers_AddReg]
HKR,,CoInstallers32,0x00010000,"WdfCoInstaller0100 7.dll,WdfCoInstaller","WinUSBCoInstaller.dll"
[CoInstallers_CopyFiles]
WinUSBCoInstaller.dll
WdfCoInstaller01007.dll
[DestinationDirs]
CoInstallers_CopyFiles=11
[SourceDisksNames]
1 = %DISK_NAME%,,,\i386
2 = %DISK_NAME%,,,\amd64
[SourceDisksFiles.x86]
WinUSBCoInstaller.dll = 1
WdfCoInstaller01007.dll = 1
[SourceDisksFiles.amd64]
WinUSBCoInstaller.dll = 2
WdfCoInstaller01007.dll = 2
[Strings]
ProviderName = "Google, Inc."
SingleAdbInterface = "Android ADB Interface"
CompositeAdbInterface = "Android Composite ADB Interface"
SingleBootLoaderInterface = "Android Bootloader Interface"
WinUSB_SvcDesc = "Android USB Driver"
DISK_NAME = "Android WinUsb installation disk"
ClassName = "Android Phone"
I also don't believe I had enabled the usb debugging before it froze in this state so am I screwed or what?
It happened even to me.... something happened in your system folder.... to make your device work again you must do a restore ( in recovery mode) of a backup that you have made before this accident happened if you did not do a backup of your device you must do it from another device
Sent from my GT-S5310 using XDA Premium 4 mobile app
---------- Post added at 09:30 AM ---------- Previous post was at 09:26 AM ----------
Of the same type otherwise your device will never work again amd you'll have to buy a new one
Sent from my GT-S5310 using XDA Premium 4 mobile app
leodani said:
It happened even to me.... something happened in your system folder.... to make your device work again you must do a restore ( in recovery mode) of a backup that you have made before this accident happened if you did not do a backup of your device you must do it from another device
Sent from my GT-S5310 using XDA Premium 4 mobile app
---------- Post added at 09:30 AM ---------- Previous post was at 09:26 AM ----------
Of the same type otherwise your device will never work again amd you'll have to buy a new one
Sent from my GT-S5310 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
how would i do a restore of a backup if i can't get it connected to the computer? I suppose I could buy another one, make a backup of it and then return it to officemax BUT can you link me to how I would create the backup and then how I would restore please?
You could install a custom recovery (like Clockwork Mod) and do it from there but if you do a backup of your brikcked device... when you do the restore it will stay bricked so you have 2 options:
1) make a backup from the same device of a person you know.... there is one big problem of this... you'll get the same IMEI number as the other phone
2) buy a new one
Sent from my GT-S5310 using XDA Premium 4 mobile app
Hard Reset G2 – In the case of password lockouts or freezing, doing a hard reset on your android device could help you get back to the factory defaults. First you need to make sure your tablet is powered off. Hold down on the Volume + button and hold down the Power button at the same time. As soon as the tablet's screen turns on let go of the Power button but keep the Volume + button held down until you see a large Android in the center of the screen. At this point you will see a screen with boot options. Use the Volume – button to go down to Wipe Data Factory Reset and tap the Power button to select this option. On the next screen use the Volume – button again to go down to Yes and use the Power button to select. At this point it will be going through the wiping and resetting process. When it's done you will see the first screen you came to when you first started the setup. Just tap the Power button to select Reboot System Now.
Make sure tablet is powered off.
Hold down Volume + button and Power button at same time.
When screen comes on let go of Power button.
When the large Android shows on screen let go of Volume + button.
Use Volume – button to scroll to Wipe Data/ Factory Reset
Tap Power button to select.
Use Volume – button to scroll to Yes.
Tap Power button to select.
Tap Power button to select Reboot System Now.
Think im screwed
Ok so I have a tri stealth g2 which was froze at boot logo, I was able to use aml flash tool and erased nand, unfortunatley the rom I installed was Novo7 which said it installed successsfully but I tried to power on my trio and nothing came on at all; however when I plug it in to my pc it comes up as a novo7 portable media player device and lets me access the internal storage. The problem is how can I flash from the internal storage, is there a program that will allow me to erase all data? The internal storage reports 5.47 gb and 5.37 gb free. Once again nothing comes on the screen so trying to gain access to any recovery not possible. I was hoping I could change the driver for the device back to the world cup driver for aml but it refuses to do it saying the driver isnt compatible grrrr. If anyone can help be appreciated.
Ok so I used adt bundle and got the device to change to Android ADB Interface tried livesuit, didnt work anyone have any suggestions?
leodani said:
It happened even to me.... something happened in your system folder.... to make your device work again you must do a restore ( in recovery mode) of a backup that you have made before this accident happened if you did not do a backup of your device you must do it from another device
Sent from my GT-S5310 using XDA Premium 4 mobile app
---------- Post added at 09:30 AM ---------- Previous post was at 09:26 AM ----------
Of the same type otherwise your device will never work again amd you'll have to buy a new one
Sent from my GT-S5310 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
so how do I back up for another device?
leodani said:
You could install a custom recovery (like Clockwork Mod) and do it from there but if you do a backup of your brikcked device... when you do the restore it will stay bricked so you have 2 options:
1) make a backup from the same device of a person you know.... there is one big problem of this... you'll get the same IMEI number as the other phone
2) buy a new one
Sent from my GT-S5310 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
That can't possibly be true, I've never seen an Android device that had the built in factory reset functionality removed...
fail
I tried tried th Power button/ volume - button and it worked, but no it doesnt. it just stays on the boot screen
Need some help with Stealth G2 10.1
Hey can anyone tell me if its fixable, i got a Trio Stealth - 10 MST 10-21. I have been searching everywhere on how to fix my problem.
So the tablet freezes on the boot screen i tried all the buttons to get to recovery mode, but i don't think it is working because once i get the correct buttons to recovery the screen turns black and nothing else happens i hold the +volume button & power button and i only get a glimmer of black i hold it for minutes at a time to see if anything happens and nothing. My questions are am i using the correct button configuration to go in to recovery? and is this fixable?
Tablet not rooted stock firmware
Thanks in advance for your help.
Same problem
I have the same Tablet and same problem. This is what I do. Leave it unplugged and on to drain the battery. After it has totally drained, recharge it then turn it on. If still won't turn on try the reset button. I use a needle to reset the tiny hole. If that won't work, hold the volume + and power buttons and hold until it turns on. This takes awhile to get it on. Then let go of the power button. If that doesn't work, I just try all the buttons and keep pushing them all and have got it to turn on. What causes mine to go black is if I hold the power button on too long. Just press it until you see Trio and let go immediately. It sucks. The tablet is actually great but that and really poor sound is its drawback.
rodlopez619 said:
Hey can anyone tell me if its fixable, i got a Trio Stealth - 10 MST 10-21. I have been searching everywhere on how to fix my problem.
So the tablet freezes on the boot screen i tried all the buttons to get to recovery mode, but i don't think it is working because once i get the correct buttons to recovery the screen turns black and nothing else happens i hold the +volume button & power button and i only get a glimmer of black i hold it for minutes at a time to see if anything happens and nothing. My questions are am i using the correct button configuration to go in to recovery? and is this fixable?
Tablet not rooted stock firmware
Thanks in advance for your help.
Click to expand...
Click to collapse
Boot Logo
Same problem, stuck at boot trying to fix for a friend but it's looking doubtful now.
And it's missing the vol and power key so i have to use things to poke at them.
Things I've noticed though.
red charging LED turns green after hitting the small reset button.
If I keep holding down the vol+ after powering up it will stay green as soon as I let it go..
it turns red.
If I use vol+ with power and do not reset it then it will stay red.
same problem here
Trio Stealth G4 7 frozen at boot logo
Hi guys...
I made a mistake..
I download "Cydia Impactor" for rooting mi device and by mistake I clicked in the menu "device/Bootloader" option (I do not what is that option for) and now my tablet is frozen at boot logo when it restart.
I saw that my computer recognize de tablet like "USB Developer" when I connect it to the USB port but in the explorer I can not see any device letter assigned to the tablet (E:, F: G: etc.).
What can I do????
Also y tried to restart pressing (Volumen down and Power on together) for factoring reset but nothing happen.
Somebody can help me??? thanks.
Found it!!!
[email protected] said:
Hi guys...
I made a mistake..
I download "Cydia Impactor" for rooting mi device and by mistake I clicked in the menu "device/Bootloader" option (I do not what is that option for) and now my tablet is frozen at boot logo when it restart.
I saw that my computer recognize de tablet like "USB Developer" when I connect it to the USB port but in the explorer I can not see any device letter assigned to the tablet (E:, F: G: etc.).
What can I do????
Also y tried to restart pressing (Volumen down and Power on together) for factoring reset but nothing happen.
Somebody can help me??? thanks.
Click to expand...
Click to collapse
After a day or two of searching I have finally found the stock firmware for the trio stealth g2 hype. Downloaded it from baidu and flashed with out an issue.
The file can be had at this link; for those who don't know how to download from baidu I will am uploading it to 4shared now.
Edit: link to the file on 4shared.
To install just extract the files unto a sdcard and power on the tablet while pressing volume down.
Have a trio g2 with same problem. Sticking at the A9 screen. I got to the recovery screen and reformatted, wiped cache and wiped media. One right after the other. Done a restart from the recovery screen and behold.....It went to the setup screen like when it was new. Hope it works for others. I tried all of the above mentioned, except for the flashing.
irapeace said:
Have a trio g2 with same problem. Sticking at the A9 screen. I got to the recovery screen and reformatted, wiped cache and wiped media. One right after the other. Done a restart from the recovery screen and behold.....It went to the setup screen like when it was new. Hope it works for others. I tried all of the above mentioned, except for the flashing.
Click to expand...
Click to collapse
I just did the same thing, and it worked for me too!
To enter the recovery screen, you press the volume down button and the power button . . . not the volume up button like others have stated. Once in recovery, I wiped cache and did a factory reset, then rebooted the device. It went to the setup screen! And it only took me 5 minutes!
Berthfield said:
After a day or two of searching I have finally found the stock firmware for the trio stealth g2 hype. Downloaded it from baidu and flashed with out an issue.
The file can be had at this link; for those who don't know how to download from baidu I will am uploading it to 4shared now.
Edit: link to the file on 4shared.
To install just extract the files unto a sdcard and power on the tablet while pressing volume down.
Click to expand...
Click to collapse
I've mirrored the download to a less garbage file host. 4shared forces you to create an account to download at 25KB/s. Totally BS.
https://mega.nz/#!RNBmjBrI!hSmMhkf8acjjEzSBuBSsKWRcEgulSYGEbEmuxSaZLP8
I realize this is an older , (to say the least) post. But could someone please tell me do I need to format the Micro SD, to make it bootable, or can I simply unzip it onto the SD and start up the tablet using the ways described in the posts on this tread? It almost seems too easy, but any help...any at all, even the littlest, tiniest ity-bity bit would be so , so, so very greatly appreciated. Thanks for your time this evening.
Hello, i've been trying to find anything related to this tablet, a Hipstreet Equinox 10.1 HS-10 DTB1-4GB, from what i can tell its supposed to be based on android 2.3 gingerbread.
The tablet basically trefuses to boot up and i've been trying to find a way to get into recovery to do a factory reset or a firmware to force flash to factory reset but i have been unable to find out how to do either, or even any information/firmwares for this tablet. if anyone can help me it would be greatly apreciated.
dragonfly14 said:
Hello, i've been trying to find anything related to this tablet, a Hipstreet Equinox 10.1 HS-10 DTB1-4GB, from what i can tell its supposed to be based on android 2.3 gingerbread.
The tablet basically trefuses to boot up and i've been trying to find a way to get into recovery to do a factory reset or a firmware to force flash to factory reset but i have been unable to find out how to do either, or even any information/firmwares for this tablet. if anyone can help me it would be greatly apreciated.
Click to expand...
Click to collapse
Your tablet may not have CWM or TWRP recoveries..Some combinations you can try are:
When tablet is booting up press VOLUP or VOLDOWN or both.
When tablet is booting up press VOLUM + Power or VOLDOWN + Power or both.
UltraWelfare said:
Your tablet may not have CWM or TWRP recoveries..Some combinations you can try are:
When tablet is booting up press VOLUP or VOLDOWN or both.
When tablet is booting up press VOLUM + Power or VOLDOWN + Power or both.
Click to expand...
Click to collapse
its most definitely on stock recovery for GB 2.3, but i have not managed to get into it. i have Vol + vol - Menu, home and back buttons, so far i've tried volume +/- both + power and ive tried menu + power as well as back and the home individually. i have not managed to get anything different other than on home + power, when i do that, i ttakes 5x longer on the "hipstreet splash logo" once it gets past that though it says android then infiniblackscreen. - i dont get anything on a host computer via the USB either when trying any of these combos - hoping to get ADB to do a factory reset via ADB.
i used to have a ployer momo 9 and i remember that tablet had a special recovery mode with a special flasher and was wondering if something like that existed for this cheap tablet which is based on just about the same thing, allwinner dual core 1.0 ghz + 512mb ram + 4 gb rom.
dragonfly14 said:
its most definitely on stock recovery for GB 2.3, but i have not managed to get into it. i have Vol + vol - Menu, home and back buttons, so far i've tried volume +/- both + power and ive tried menu + power as well as back and the home individually. i have not managed to get anything different other than on home + power, when i do that, i ttakes 5x longer on the "hipstreet splash logo" once it gets past that though it says android then infiniblackscreen. - i dont get anything on a host computer via the USB either when trying any of these combos - hoping to get ADB to do a factory reset via ADB.
i used to have a ployer momo 9 and i remember that tablet had a special recovery mode with a special flasher and was wondering if something like that existed for this cheap tablet which is based on just about the same thing, allwinner dual core 1.0 ghz + 512mb ram + 4 gb rom.
Click to expand...
Click to collapse
Using ADB is a good idea .I didn't think of that though :silly:...
UltraWelfare said:
Using ADB is a good idea .I didn't think of that though :silly:...
Click to expand...
Click to collapse
thanks, but yeah, i cant get anything out of it so far and was hoping someone had the magical way to revive it :/ i believe on my ployer it was something ridiculous like vol - + home + back + power for 5 seconds and i had to get it flashing within 5 seconds of that or it would switch modes.... x_x
dragonfly14 said:
thanks, but yeah, i cant get anything out of it so far and was hoping someone had the magical way to revive it :/ i believe on my ployer it was something ridiculous like vol - + home + back + power for 5 seconds and i had to get it flashing within 5 seconds of that or it would switch modes.... x_x
Click to expand...
Click to collapse
Wait I found something for you
There is a few tricks to get your Tablet back , You require a few things
-A usb cable to connect to computer
-Internet connectivity
Now Lets start by putting the tablet in Android recover mode .
1. Connect the tablet to the USB port on the Computer .
2. Press and hold the power button and the Big button on the tablet , Keep pressing it until the logo of the android gut with his gut open shows up .
3. It is possible to perform a reset using the ADB (Android Debug Bridge)
I did mine on Windows XP , (Does your tablet install correctly in the Device manager? )
If so That is great news , You may goto step 5
If not Goto step 4 :
Step 4: Getting the Chinese driver equivalent for your tablet .
Get the drivers for the Ainol 7" Auror tablet (or equivalent )
Now Before the driver will work with your device (you can try to install it but it will give you an INF error)
You must edit the file (.INF) to match your USB id of the tablet
(At the bottom of the file change the STRINGS section to the device codes of your tablet ) (found by right clicking the Unknown device in the device manager . the (VID_1f3a_PID_efe8) is the HARDWARE ID and the
[Strings]
USBDRV="USB Devices"
USB\VID_1f3a&PID_efe8.DeviceDesc="USBDevice(VID_1f3a_PID_efe8)"
YOUR STRINGS:
USBDRV="USB Devices"
USB\<YOURDEVICEID>.DeviceDesc=USBDevice(<YOURDEVICEID>)"
Step 5:
Get the Recovery tool from here
https://spideroak.com/share/KNQW243.../CWM_Recovery_Manta_MID08_windows_install.zip
This will give you a suite of tools to restore your device to factory reset
Use it to install the recovery partition , and then reboot your device in recovery mode , Then use the Vol + and - buttons to navigate and power button to Enter .
(Source : click here)
Hello there, i have a Hipstreet too, but my android have crashed and dont turn on anymore.
I cant find the stock rom or custom rom anywhere.
Can you find some of these?
If you dont, you can make a backup and send a link to me?
Thanks and sorry for the english.
Good day to all,
I have someone's phone but I need some help to resolve it's issue. It's an Alcatel One touch pop c1 4015a. The owner asked me how to factory reset it, so I gave step by step instructions as to how to do it. After resetting the phone, it some how got soft bricked, just stays at the logo screen.
So right now, I have it trying to flash it with so flash tools. Tried accessing recovery mode but it was not working. So I thought of if it was possible to flash a recovery image via so flash tools, which I found and tried but it wouldn't start downloading. Afterwards, all of a sudden the recovery mode was working (I swear it was not working before) so I am trying to install the stock rom via sdcard, but it starts and stops.
So right now I am think if the USB debugging feature may have anything to do with it or maybe I have to install cwm or twrp. Which is why I am here with the following questions:
1 Is it possible to install cwm via the phone stock recovery mode?
2 Is it possible to use ADB to install cwm? If so can I get some noob friendly instructions to do so
3 Can I somehow enable USB debug via recovery mode or ADB?
4 What on earth can I do to fix this phone if all of the above is not possible?
I do apologize as well if I posted this question in the wrong area or if there are similar topics like this one which I didn't see.
Thanks much
Sent from my Timmy E86 using XDA Free mobile app
Okay bud, I can tell you're new to this, answer to your first question is NO, you have to do that via fast boot which I can tell you how to get into, second questions answer is MAYBE, but fast boot is easier and uses the same drivers (on your of) third questions answer is NO only on custom recoveries like cwm and twrp. Fourth questions answer is, if you have a cwm recovery image, boot the phone into fast boot (two ways: look in recovery for an option called "reboot boot loader" if you can't find it, try booting up the phone while holding volume down (-) and power. Then connect it to your pc and open a terminal or command prompt and type: fastboot flash recovery (now drag and drop the recovery file in the command prompt, it should automatically enter its file path) and hit enter. That should work, if you need more help ask
Sent from my iPhone using Tapatalk
MeowDude said:
Okay bud, I can tell you're new to this, answer to your first question is NO, you have to do that via fast boot which I can tell you how to get into, second questions answer is MAYBE, but fast boot is easier and uses the same drivers (on your of) third questions answer is NO only on custom recoveries like cwm and twrp. Fourth questions answer is, if you have a cwm recovery image, boot the phone into fast boot (two ways: look in recovery for an option called "reboot boot loader" if you can't find it, try booting up the phone while holding volume down (-) and power. Then connect it to your pc and open a terminal or command prompt and type: fastboot flash recovery (now drag and drop the recovery file in the command prompt, it should automatically enter its file path) and hit enter. That should work, if you need more help ask
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Ok I dont see that option in recovery mode at all. Which leaves the vol - + power button combo. Is something specific suppose to happen while holding these buttons? The phone might just continuously restart until i let go then it would go to the logo screen. If I try vol + & - with the power button, it will stay blank for a while as after i let go the button then it would power on to the logo screen.
It should either show a custom screen (pic maybe?) or freeze at the boot logo.
Sent from my iPhone using Tapatalk
---------- Post added at 11:02 PM ---------- Previous post was at 11:01 PM ----------
Or you can try pressing power for a second (until you see the boot logo or feel it vibrate) then releasing it, and then holding volume down. This process varies on phones
Sent from my iPhone using Tapatalk
Still no luck. And for some reason, it won't detect the phone in ADB mode. I have installed drivers for it, more than once.
Sent from my Timmy E86 using XDA Free mobile app
Are you sure they're the right drivers? If you're on Windows plug in the device while in recovery, and open control panel, then click devices and printers, and it should show you a list of device attached to your computer,now find yours (or tell me what you see) and ill help you from there. Oh, and also, what SPECIFIC device is this?
Sent from my iPhone using Tapatalk
It's an Alcatel one touch c1. Right now , I connected it to the pc while in recovery mode. But it gives a drive descriptor request error. I installed all drivers I came across for this phone.
Sent from my Timmy E86 using XDA Free mobile app
It gives an option in recovery mode to update via ADB as well
Sent from my Timmy E86 using XDA Free mobile app
EDIT: If i try to use the sdcard option, it immediately stops
AnoitedOne347 said:
It gives an option in recovery mode to update via ADB as well
Sent from my Timmy E86 using XDA Free mobile app
EDIT: If i try to use the sdcard option, it immediately stops
Click to expand...
Click to collapse
Try updating it through adb
Sent from my iPhone using Tapatalk