Does this happen to anyone else? My average battery life is something like 18 hours; whenever I wipe battery stats I can run my phone (with the same kind of usage) for over 24 hours; after calibration is complete, battery life drops to 18 hours or so again.
Weird..
The first run when wiping battery stats is always longer than the 2nd. But give it another run, and it will even out, and the longer you go, the more even it gets.
Sent from my SGH-T959 using XDA App
This process below (from here http://forum.xda-developers.com/showpost.php?p=11285391&postcount=1 ) has turned my phone into a battery champ
HOW TO RECALIBRATE YOUR BATTERY (by heartagramm):
COMPLETE GUIDE!!!
You'll have to use the phone for about 1-4 days (although it varies depending on the phone and battery used; every phone is an individual). It runs out of battery. Yes. Let it run. Recharge. After 3-4 recharges the battery will "gain" it's performance back.
After 3-4 full charge/full drain -cycles, do the following:
1. Charge the battery up to fullest.
2. Keep it plugged in to charger, and reboot to recovery.
3. On the recovery, go advanced, wipe battery stats, scroll on to yes BUT Don't wipe them yet. When you're ready, quickly remove the battery cable and push to wipe the battery stats.
4. Reboot the phone, use normally. Let it run completely out of battery.
5. Charge the phone back to full. Turn off phone. Charge until it says 100% on the green bar and vibrates for full charge.
6. The Important Part. Remove the charge cable for 0-0.5 seconds and plug it back in instantly. Let it charge to 100% again. Do this 1-2 times again, so you've done this 2-3 times total.
7. Reboot to recovery, wipe the battery stats again as on the step 3.
8. After wiping the battery stats, plug the charger back in the phone.
9. Reboot to ROM. Keep the cable plugged in. Keep it plugged in for about 30 mins to 2 hrs. Unplug. Should say 100%, mine did for about 40 mins after it depleted onto 99%.
And this is the way you should really gain great battery performance.
Related
Hi all,
I have a question about battery life on the Simply Honey 2.7.2 ROM
My phone is usually idle overnight, but i notice a drop of about 25-30% in 8 hours. Is this usual?
Here are some screenshots
Battery Plot (1.26 am to 9.26am) Battery was 100% at 1.26
System details
Top Apps
Is this pretty normal for overnight battery drain? The Device usage indicates almost no use..so i'm wondering why the battery is draining.
Any help would be appreciated.
Thank you
I'm having the same issue. With Darky's 9.5 the phone easily last a day, now it's lasting 9 hours or so. I just flashed the new ROM yesterday.
This is from the Simply Honey post:
HOW TO RECALIBRATE YOUR BATTERY (by heartagramm):
COMPLETE GUIDE!!!
You'll have to use the phone for about 1-4 days (although it varies depending on the phone and battery used; every phone is an individual). It runs out of battery. Yes. Let it run. Recharge. After 3-4 recharges the battery will "gain" it's performance back.
After 3-4 full charge/full drain -cycles, do the following:
1. Charge the battery up to fullest.
2. Keep it plugged in to charger, and reboot to recovery.
3. On the recovery, go advanced, wipe battery stats, scroll on to yes BUT Don't wipe them yet. When you're ready, quickly remove the battery cable and push to wipe the battery stats.
4. Reboot the phone, use normally. Let it run completely out of battery.
5. Charge the phone back to full. Turn off phone. Charge until it says 100% on the green bar and vibrates for full charge.
6. The Important Part. Remove the charge cable for 0-0.5 seconds and plug it back in instantly. Let it charge to 100% again. Do this 1-2 times again, so you've done this 2-3 times total.
7. Reboot to recovery, wipe the battery stats again as on the step 3.
8. After wiping the battery stats, plug the charger back in the phone.
9. Reboot to ROM. Keep the cable plugged in. Keep it plugged in for about 30 mins to 2 hrs. Unplug. Should say 100%, mine did for about 40 mins after it depleted onto 99%.
And this is the way you should really gain great battery performance.
Click to expand...
Click to collapse
I'm going to try this and hopefully it works.
Let us know if it sorts itself out after a couple of days...
Chris.
Thanks. I will try this.
I recently downloaded a Battery Calibration App from the market too (NeMa) and calibrated my battery using that..but I'll try this method also.
Let me know if you have any improvements also.
Thanks!
riskaa
I switched to Doc's ROM and battery life is back to normal. I'll try Simply again after a few versions.
Sent from my GT-I9000 using XDA App
I don't think there are going to be new versions, because he's now doing some Gingerbread based ROMS.
Which one is Doc's ROM?
I'm on SimplyHoneyV1.0XE and have been for a couple of days. This is my first Simply Honey experience but I think this is the best battery life I've ever gotten on ANY ROM including stock. Given it is a little early in my test to determine just how good it is going to be but I would recommend you give it a try and see how it does on your battery.
P.S. My findings were based on the fact that after a 100% charge, light usage (2-4 phones calls, and several texts) for almost 10 hours I still had 89% of my battery. Pretty impressive if you ask me.
riskaa said:
Thanks. I will try this.
I recently downloaded a Battery Calibration App from the market too (NeMa) and calibrated my battery using that..but I'll try this method also.
Let me know if you have any improvements also.
Thanks!
riskaa
Click to expand...
Click to collapse
I'm pretty sure they perform the same function. When you touch the "Calibrate Battery" button, the app automatically performs all the steps mentioned (wipe battery stats, mainly).
One app you might try is Juice Defender. I've used it a few times, and it worked well when battery life was an issue for me (I've switched to Axura, and it isn't anymore. Neither with Bionix).
New gTablet, just use only 1 day, the charging allway in 96%!!! never go upto 100%, is this normal?
Pls: i see 97% about 5 minute ago, but now back to 96%,,,,,,
thanks
Yes, it's normal, everybody has inaccurate battery readings on Gtablets.
To try to fix it, you can drain the battery all the way down, then turn it on a couple times ot make sure that it's completely drained. Then, plug in the charger, turn it on in recovery mode (assuming that you have CWM installed) then wipe the battery stats. Reboot, and charge it all the way back up. it may charge to 100%.
Mine has a different issue, it will charge to 100%, then it will stay there for an extended period of time. 3 hours later, it might still be on 100%, but I know that it's not. If I let it drain down, it will actually turn itself off around 13% - 15%, so my battery calibration is off by that much in the positive. The first time I wiped stats, it fixed it, but it's slowly crawling back up again.
thank . TJEvans, ithink i need to return back. so many problem with my gtablet.
Hi, I have currently upgraded my Xperia Neo to CM9. I have been experiencing a bit lesser batter life.
Also when i use CpySpy app it doesnt show the time spent by the processor in the specified frequencies. It always shows 0 for all
states. that is definitely not correct. The system can't be idle when i use right? So i'm wondering is there any issue with CM9 or my phone particularly. Also i have already used CM7 and CpySpy was giving me right numbers. I need help to figure out why my battery drains even when my phone is in idle and why there are no numbers in CpuSpy.
Thanks in advance
I can't guarantee, but cpu usage/phone turning to be hot after a while of use/short battery life is something common with most of androids. On my HTC HD2 battery life is twice as short since I started to use android.
If, after rooting or more likely the case after flashing a new rom, you often have battery reporting errors, and re-calibrating the battery along with some steps I will outline for you below will ensure that your battery is getting a full charge, and the battery reporting accuracy is right on. I run my device in performance mode all the time, and with a CPU overclock of 1.25GHz and various tweaks, I have about a day an a half to a day and a quarter of full runtime from my battery. This is with moderate to heavy usage (calls, emailing, text, gaming, web browsing, etc.) so you should have no problems getting acceptable battery performance after following these steps:
1. Take the case off your device (one of the latter steps involves taking the battery out from the phone while it's plugged in. Make sure your case won't stand in the way.)
2. Install Battery Calibration app from the market
3. Plug in your device to charge while it's on, wait till it gets to a 100%
4. When the charge is 100%, open the BatteryCalibration app and lookup what the charge is in MV while at 100%. Write it down.
My Atrix 2 was showing ~3400MV while at 100%, which is definitely not the maximum capacity.
5. Discharge your device completely until it shuts off.
A good way of doing this quickly is by turning on wifi, and a video player.
6. Without turning on the phone plug it into a wall charger and let it get to 100%
7. When it's at 100%, without unplugging it from the wall charger, take off the battery cover, and take the battery out.
Your phone will "reboot" and show a Missing Battery icon.
8. Without unplugging the phone from the wall charger or turning it on, put the battery back in and wait until the phone recognizes the battery.
9. Your battery should now be recognized by the phone, and showing a charge % significantly lower than 100%.
Mine showed only 5%.
10. Let it sit there charging for 2-3 hours (or more).
My phone wouldn't charge past 10%, but yours might. The numbers don't matter much as the phone is definitely getting additional charge that could have been lost while flashing ROMs, etc.
11. After 2-3 hours (or more), turn the phone on while holding the volume down button and get into CWM.
Do not disconnect it from the charger still!
12. Wipe battery stats in CWM, reboot.
Do not disconnect it from the charger still!
13. When the phone turns on, go into Battery Calibration app again and look up your MV numbers -if you were like me, they should be significantly higher than before. After this whole process I had 4351MV at 100%, comparing to 3400MV before calibration.
Do not disconnect it from the charger still!
14. Before going to sleep - Install Watchdog Task Manager Lite from the market. Go into it's preferences, set CPU threshhold to 20%, check "Include phone processes", check "Monitor phone processes", check "Display all phone processes", set system CPU threshhold to 20% as well.
Do not disconnect it from the charger still!
15. Make sure your wifi and data connections are off. Now finally unplug the phone from the charger.
Go to bed, let your phone sleep too.
16. Success! Next morning check where your battery % is at and if you followed the instructions correctly / got lucky like me, your battery life should be 90% or more.
I went to bed with 98% and woke up to 94%. So, I consider this mission a success.
Sent from my MB865 using xda's premium carrier pigeon service
Apex_Strider said:
If, after rooting or more likely the case after flashing a new rom, you often have battery reporting errors (as mentioned above), and re-calibrating the battery along with some steps I will outline for you below will ensure that your battery is getting a full charge, and the battery reporting accuracy is right on. As far as power cycling, I don't know that it does much good. I run my device in performance mode all the time, and with a CPU overclock of 1.25GHz and various tweaks, I have about a day an a half to a day and a quarter of full runtime from my battery. This is with moderate to heavy usage (calls, emailing, text, gaming, web browsing, etc.) so you should have no problems getting acceptable battery performance after following these steps:
1. Take the case off your device (one of the latter steps involves taking the battery out from the phone while it's plugged in. Make sure your case won't stand in the way.)
2. Install Battery Calibration app from the market
3. Plug in your device to charge while it's on, wait till it gets to a 100%
4. When the charge is 100%, open the BatteryCalibration app and lookup what the charge is in MV while at 100%. Write it down.
My Atrix 2 was showing ~3400MV while at 100%, which is definitely not the maximum capacity.
5. Discharge your device completely until it shuts off.
A good way of doing this quickly is by turning on wifi, and a video player.
6. Without turning on the phone plug it into a wall charger and let it get to 100%
7. When it's at 100%, without unplugging it from the wall charger, take off the battery cover, and take the battery out.
Your phone will "reboot" and show a Missing Battery icon.
8. Without unplugging the phone from the wall charger or turning it on, put the battery back in and wait until the phone recognizes the battery.
9. Your battery should now be recognized by the phone, and showing a charge % significantly lower than 100%.
Mine showed only 5%.
10. Let it sit there charging for 2-3 hours (or more).
My phone wouldn't charge past 10%, but yours might. The numbers don't matter much as the phone is definitely getting additional charge that could have been lost while flashing ROMs, etc.
11. After 2-3 hours (or more), turn the phone on while holding the volume down button and get into CWM.
Do not disconnect it from the charger still!
12. Wipe battery stats in CWM, reboot.
Do not disconnect it from the charger still!
13. When the phone turns on, go into Battery Calibration app again and look up your MV numbers -if you were like me, they should be significantly higher than before. After this whole process I had 4351MV at 100%, comparing to 3400MV before calibration.
Do not disconnect it from the charger still!
14. Before going to sleep - Install Watchdog Task Manager Lite from the market. Go into it's preferences, set CPU threshhold to 20%, check "Include phone processes", check "Monitor phone processes", check "Display all phone processes", set system CPU threshhold to 20% as well.
Do not disconnect it from the charger still!
15. Make sure your wifi and data connections are off. Now finally unplug the phone from the charger.
Go to bed, let your phone sleep too.
16. Success! Next morning check where your battery % is at and if you followed the instructions correctly / got lucky like me, your battery life should be 90% or more.
I went to bed with 98% and woke up to 94%. So, I consider this mission a success.
Sent from my MB865 using xda's premium carrier pigeon service
Click to expand...
Click to collapse
Great, what should be. :good:
hi guys! i'm running cm7.2 on my su660 (it's a kang build which is ported from p990 official CM build). and i have a problem on charging the phone. when the phone have 10% of battery left, i plug in the charger, the phone show the charging symbol . but when i leave it sleep and come back after 'bout 3 hours, it still show 10%. but the voltage in sparepart is aproximate 4200 mV. so the battery is fully charged but the rom didn't regconize it. but then after some minutes turning the screen on, the rom show that phone is fully charged. so i guess that the battery percentage counter doesn't work why the phone is pluged in and sleep. so this is a rom issue? can i fix it myself?
PS: sorry for my poor English because i'm not a native English speaker. i'm from VietNam. i tried my best to explane my case. hope u can understand me!
If, after rooting or more likely that case after flashing a new rom, you often have battery reporting errors, and re-calibrating the battery along with some steps I will outline for you below will ensure that your battery is getting a full charge, and the battery reporting accuracy is right on. As far as power cycling, I don't know that it does much good. I run my device in performance mode all the time, and with a CPU overclock of 1.25GHz and various tweaks, I have about a day an a half to a day and a quarter of full runtime from my battery. This is with moderate to heavy usage (calls, emailing, text, gaming, web browsing, etc.) so you should have no problems getting acceptable battery performance after following these steps:
1. Take the case off your device (one of the latter steps involves taking the battery out from the phone while it's plugged in. Make sure your case won't stand in the way.)
2. Install Battery Calibration app from the market
3. Plug in your device to charge while it's on, wait till it gets to a 100%
4. When the charge is 100%, open the BatteryCalibration app and lookup what the charge is in MV while at 100%. Write it down.
My Atrix 2 was showing ~3400MV while at 100%, which is definitely not the maximum capacity.
5. Discharge your device completely until it shuts off.
A good way of doing this quickly is by turning on wifi, and a video player.
6. Without turning on the phone plug it into a wall charger and let it get to 100%
7. When it's at 100%, without unplugging it from the wall charger, take off the battery cover, and take the battery out.
Your phone will "reboot" and show a Missing Battery icon.
8. Without unplugging the phone from the wall charger or turning it on, put the battery back in and wait until the phone recognizes the battery.
9. Your battery should now be recognized by the phone, and showing a charge % significantly lower than 100%.
Mine showed only 5%.
10. Let it sit there charging for 2-3 hours (or more).
My phone wouldn't charge past 10%, but yours might. The numbers don't matter much as the phone is definitely getting additional charge that could have been lost while flashing ROMs, etc.
11. After 2-3 hours (or more), turn the phone on while holding the volume down button and get into CWM (if installed) or use Rom Manager (is device is supported).
Do not disconnect it from the charger still!
12. Wipe battery stats in CWM, reboot.
Do not disconnect it from the charger still!
13. When the phone turns on, go into Battery Calibration app again and look up your MV numbers -if you were like me, they should be significantly higher than before. After this whole process I had 4351MV at 100%, comparing to 3400MV before calibration.
Do not disconnect it from the charger still!
14. Before going to sleep - Install Watchdog Task Manager Lite from the market. Go into it's preferences, set CPU threshhold to 20%, check "Include phone processes", check "Monitor phone processes", check "Display all phone processes", set system CPU threshhold to 20% as well.
Do not disconnect it from the charger still!
15. Make sure your wifi and data connections are off. Now finally unplug the phone from the charger.
Go to bed, let your phone sleep too.
16. Success! Next morning check where your battery % is at and if you followed the instructions correctly / got lucky like me, your battery life should be 90% or more.
I went to bed with 98% and woke up to 94%. So, I consider this mission a success.
Sent from my MB865 using xda's premium carrier pigeon service
i hv bnattery problem for 3-4 month
still cannot solve the battery problem
i think i have done some wrong steps in the battery calibration
when my battery is fully charged in a battery changer(charger for battery only)
when i put the battery into the phone, it's shows that there is about 30% of battery
when i further use the battery, the battery level rise (without charging!) to 100 then drop to 0 and turn off
the time that the phone can use from 100% to 0% is quite short
when every time after charging, the battery level is 100%
it won't charge to the "real" full battery level, ie ~30% (SORRY FOR MY POOR ENGLISH)
how should i calibrate?
i used the battery calibration app, but no use.
Charge to 100 then use battery calibrator from market very simple
Sent from my SCH-I500 using XDA
If your recovery is ClockWorkMod, then there is an option to "Clear Battery Stats". Just try to see whether it helps.
~Cheers
It's a few days late, but battery calibration is unnecessary on modern batteries (Lithium). All the apps do is delete a small file that records power usage, they do not affect battery life in any way. This file is cleared automatically (by the system) when the phone is fully charged.
Further, full charge/discharge cycles will actually have a net harmful effect on your battery life. A lithium ion battery has a limited number of charge/discharge cycles it can sustain before becoming more effective at being a paperweight than powering anything. The full cycles you are doing simply eat into the battery's overall life expectancy.
For instance, it is better to charge from 50% to 100% multiple times than it is to go from 0 to 100 once.
Personally, I would just replace the battery.
I would suggest u to calibrate the battery in the clockworkmod recovery too
if this wont has any effect take into consideration that your battery might be damaged
i faced this problem one year ago with a galaxy spica the battery was shown as full and after a restart it was almost empty and calibrating the battery did not had any effect
so have a try and report afterwards
If, after rooting or more likely that case after flashing a new rom, you often have battery reporting errors (as mentioned above), and re-calibrating the battery along with some steps I will outline for you below will ensure that your battery is getting a full charge, and the battery reporting accuracy is right on. I run my device in performance mode all the time, and with a CPU overclock of 1.25GHz and various tweaks, I have about a day an a half to a day and a quarter of full runtime from my battery. This is with moderate to heavy usage (calls, emailing, text, gaming, web browsing, etc.) so you should have no problems getting acceptable battery performance after following these steps:
1. Take the case off your device (one of the latter steps involves taking the battery out from the phone while it's plugged in. Make sure your case won't stand in the way.)
2. Install Battery Calibration app from the market
3. Plug in your device to charge while it's on, wait till it gets to a 100%
4. When the charge is 100%, open the BatteryCalibration app and lookup what the charge is in MV while at 100%. Write it down.
My Atrix 2 was showing ~3400MV while at 100%, which is definitely not the maximum capacity.
5. Discharge your device completely until it shuts off.
A good way of doing this quickly is by turning on wifi, and a video player.
6. Without turning on the phone plug it into a wall charger and let it get to 100%
7. When it's at 100%, without unplugging it from the wall charger, take off the battery cover, and take the battery out.
Your phone will "reboot" and show a Missing Battery icon.
8. Without unplugging the phone from the wall charger or turning it on, put the battery back in and wait until the phone recognizes the battery.
9. Your battery should now be recognized by the phone, and showing a charge % significantly lower than 100%.
Mine showed only 5%.
10. Let it sit there charging for 2-3 hours (or more).
My phone wouldn't charge past 10%, but yours might. The numbers don't matter much as the phone is definitely getting additional charge that could have been lost while flashing ROMs, etc.
11. After 2-3 hours (or more), turn the phone on while holding the volume down button and get into CWM.
Do not disconnect it from the charger still!
12. Wipe battery stats in CWM, reboot.
Do not disconnect it from the charger still!
13. When the phone turns on, go into Battery Calibration app again and look up your MV numbers -if you were like me, they should be significantly higher than before. After this whole process I had 4351MV at 100%, comparing to 3400MV before calibration.
Do not disconnect it from the charger still!
14. Before going to sleep - Install Watchdog Task Manager Lite from the market. Go into it's preferences, set CPU threshhold to 20%, check "Include phone processes", check "Monitor phone processes", check "Display all phone processes", set system CPU threshhold to 20% as well.
Do not disconnect it from the charger still!
15. Make sure your wifi and data connections are off. Now finally unplug the phone from the charger.
Go to bed, let your phone sleep too.
16. Success! Next morning check where your battery % is at and if you followed the instructions correctly / got lucky like me, your battery life should be 90% or more.
I went to bed with 98% and woke up to 94%. So, I consider this mission a success.
Sent from my Atari Falcon030