TUTORIAL , how to bring your LG P500 back to life/unBrick.

TUTORIAL , how to bring your LG P500 back to life/unBrick. - Optimus One, P500, V General

Hello,
- i'm the proud owner of an LG P500, i mannaged to "kill" it alot of times, one time i bricked it so bad the power button was useless. I'm going to tell you how i always manneged to fix it.
1. - install the USB DRIVERS for LG P500 Download LINK
2. - extract the KDZ archive , install msxml.msi, Download LINK, Download Froyo 2.2.2. v10E.kdz after that open >> KDZ_FW_UPD.exe, select type 3GQCT and mode DIAG (select this only if your phone starts when you connect the USB and the battery charging logo apears) if the phone starts in Emergency Mode or dosen't start at all >> remove battery and while holding the BACK and volume UP buttons connect the USB, the phone should start in Emergency Mode, after that select in KDZ, MODE > EMERGENCY, select file > V10E_00.kdz and press the "Launch software update" .
- wait for KDZ to do it's job ( until it says FINISHED) after it is finished it will reset the phone (alot of times the phone wolden't start after reset and i had to start it manualy @power button) an LG logo should apear , then an Android logo, wait about 5 - 10 min (the phone should start and you will have froyo 2.2.2. working), but if the Android LOGO stops or lags for 2,3 seconds then you must remove battery , put it back , and power on the phone. if it dose the same thing , then you must reflash your phone. Usualy it works with the battery on and simply flashing under DIAG mode.
- after reflashing if you have the same problem , you must remove battery and try installing it DIAG mode. if it still dosen't work enter emergency mode ( UP + BACK + connect USB (or press the power button)) and reflash using KDZ , MODE >>> EMERGENCY.
- when phone is connected go to COMPUTER > PROPERTIES > DEVICE MANAGER > MODEMS > and disable LGE Modem.. (some say it helps i diden't saw any difference.)
- as i was saying i killed my phone alot of times, KDZ always helped me bring it back to life , be patient.. and if you get alot of errors and flash meny times the phone gets hot , leave it to cool for a while and then try again.
be patient !! hope this will help you ..
sorry for my bad english !!

i dont mean to be rude, but there are guides on this already (i mean, how else would you know this yourself)
http://forum.xda-developers.com/showthread.php?t=1060121
http://forum.xda-developers.com/showthread.php?t=875881

sweetnsour said:
i dont mean to be rude, but there are guides on this already (i mean, how else would you know this yourself)
http://forum.xda-developers.com/showthread.php?t=1060121
http://forum.xda-developers.com/showthread.php?t=875881
Click to expand...
Click to collapse
- i understand, you'r right, but "I'm going to tell "you" how i always manneged to fix it."
PS: i wrote this tutorial after reading alot about unbricking , i tried to make it simple.

xzet2 said:
- i understand, you'r right, but "I'm going to tell "you" how i always manneged to fix it."
PS: i wrote this tutorial after reading alot about unbricking , i tried to make it simple.
Click to expand...
Click to collapse
what you posted is the exact same thing as what is posted in my links

okay , i diden't saw the detail'd tutorial with pictures , if this one is usless "someone" delete it.

no need delete
just edit ur thread with got solved or thread close something like this ~~

Thanks alot, dude. My phone is working again.

rainCz said:
Thanks alot, dude. My phone is working again.
Click to expand...
Click to collapse
well i think this one has helped someone
good luck

Bricked my phone beyond recovery
i totally bricked my phone, while i was using kdzupdater something went wrong . Finally had to go to the LG service center ( hope my warranty is not void in India). Well they said the phone is not responding to software it will need a new PCB. So my phone goes for like 2-3 days away from me.

As posted before, It's already been posted on here but great work nonetheless. It's better to have more posts like these then have more people posting about how to unbrick there phone.

Thanks for the post... I was a little unsure about flashing via KDZ, but this thread actually points few ways of procedure in case of things going wrong...
I think, this thread is pretty helpful and complements well with the others regular "how to" threads!

LG p500 Unbrick
Dear Sir,
I have lg p500, Yesterday i was downgrade my mobile software from 2.3.3 to 2.2 through KDZ updater. while updating error came finally my mobile now in dead condition, I tried to boot emergency mode (Volume UP+Back Button+USB Connect) there is no reaction on my mobile screen even though battery was removed.Any body help me to come back live my phone(I had lost my mobile purchase bill, if it is available i will give to LG service center)

xzet2 said:
Hello,
- i'm the proud owner of an LG P500, i mannaged to "kill" it alot of times, one time i bricked it so bad the power button was useless. I'm going to tell you how i always manneged to fix it.
1. - install the USB DRIVERS for LG P500 Download LINK
2. - extract the KDZ archive , install msxml.msi, Download LINK, Download Froyo 2.2.2. v10E.kdz after that open >> KDZ_FW_UPD.exe, select type 3GQCT and mode DIAG (select this only if your phone starts when you connect the USB and the battery charging logo apears) if the phone starts in Emergency Mode or dosen't start at all >> remove battery and while holding the BACK and volume UP buttons connect the USB, the phone should start in Emergency Mode, after that select in KDZ, MODE > EMERGENCY, select file > V10E_00.kdz and press the "Launch software update" .
- wait for KDZ to do it's job ( until it says FINISHED) after it is finished it will reset the phone (alot of times the phone wolden't start after reset and i had to start it manualy @power button) an LG logo should apear , then an Android logo, wait about 5 - 10 min (the phone should start and you will have froyo 2.2.2. working), but if the Android LOGO stops or lags for 2,3 seconds then you must remove battery , put it back , and power on the phone. if it dose the same thing , then you must reflash your phone. Usualy it works with the battery on and simply flashing under DIAG mode.
- after reflashing if you have the same problem , you must remove battery and try installing it DIAG mode. if it still dosen't work enter emergency mode ( UP + BACK + connect USB (or press the power button)) and reflash using KDZ , MODE >>> EMERGENCY.
- when phone is connected go to COMPUTER > PROPERTIES > DEVICE MANAGER > MODEMS > and disable LGE Modem.. (some say it helps i diden't saw any difference.)
- as i was saying i killed my phone alot of times, KDZ always helped me bring it back to life , be patient.. and if you get alot of errors and flash meny times the phone gets hot , leave it to cool for a while and then try again.
be patient !! hope this will help you ..
sorry for my bad english !!
Click to expand...
Click to collapse
Thank you for your information... Actually Today when i WAS UPDATING MY p500 FROM ROM 2.2.2 TO OFFICIAL 2.3 THROUGH KDZ,I got an error in the updating process, My phone shows only emergency mode... and after that i removed the battery and try to switch on the phone.. But my phone is seems totally dead.... I had also tried your procedure. But it wont work... Please help me how can I unbrick it..
Plz...plzz.plzzz.....
---------- Post added at 03:13 PM ---------- Previous post was at 03:08 PM ----------
sweetnsour said:
i dont mean to be rude, but there are guides on this already (i mean, how else would you know this yourself)
http://forum.xda-developers.com/showthread.php?t=1060121
http://forum.xda-developers.com/showthread.php?t=875881
Click to expand...
Click to collapse
Hello sir,
Thank you for your information... Actually Today when i WAS UPDATING MY p500 FROM ROM 2.2.2 TO OFFICIAL 2.3 THROUGH KDZ,I got an error in the updating process, My phone shows only emergency mode... and after that i removed the battery and try to switch on the phone.. But my phone is seems totally dead.... I had also tried your procedure. But it wont work... Please help me how can I unbrick it..
Plz...plzz.plzzz.....

i keep getting upgrade error
wparam:100
lparam: 502 ,
i have the optimus m , and when i connect it in emergency mode my computer AUTOMATICALLY says that there is a usb 2.0 slot avaible , and when i connect it to another it says the same thing , and i am positive that all my usbs are 2.0
Sent from my Mytouch 4G Running Capychimps Sense 3.5 rom (v.4.0)

and then KDZ force closes
Sent from my Mytouch 4G Running Capychimps Sense 3.5 rom (v.4.0)

also the phone unmounts (the screen flashes) every 25 seconds
Sent from my Mytouch 4G Running Capychimps Sense 3.5 rom (v.4.0)
---------- Post added at 04:34 PM ---------- Previous post was at 04:14 PM ----------
Heres my Log :
[16:30:43:509] : =============================================
[16:30:43:509] : Log is started on 06.01.2012, at 16:30:43:509,
executable: C:\Users\David\Desktop\KDZ_FW_UPD_EN\KDZ_FW_UPD.exe (ProcID: 0x00000a1c),
compile time : Dec 8 2010 09:19:37
[16:30:43:509] : Version :
[16:30:43:509] : Get Usb Port
[16:30:43:509] : rsi.strFriendlyName=LGE CDMA USB Serial Port (COM6)
[16:30:43:509] : FriendlyNameList[iii].szFriendlyName=LGE CDMA USB Serial Port
[16:30:43:509] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 1 - COM6
[16:30:43:509] : Port = COM6
[16:30:43:525] : UNKNOWN : Req(12) -> Rsp(13)
[16:30:48:548] : RX Timeout : 5.0 seconds
[16:30:48:548] : RX TIMEOUT
[16:30:48:564] : UNKNOWN : Req(12) -> Rsp(13)
[16:30:48:564] : >> DIAG_STATUS_F FAILED
[16:30:48:579] : >>Get Model Name [DIAG_VERNO_F]
[16:30:51:606] : RX Timeout : 3.0 seconds
[16:30:51:606] : RX TIMEOUT
[16:30:51:621] : BAD CONN MODE : Req(0) -> Rsp(3)
[16:30:54:648] : RX Timeout : 3.0 seconds
[16:30:54:648] : RX TIMEOUT
[16:30:54:663] : BAD CONN MODE : Req(0) -> Rsp(3)
[16:30:57:690] : RX Timeout : 3.0 seconds
[16:30:57:690] : RX TIMEOUT
[16:30:57:705] : BAD CONN MODE : Req(0) -> Rsp(3)
[16:30:57:705] : FAIL (No Phone)
[16:30:57:705] : GetModelName() Operation Failed Check Diag CMD
[16:30:57:705] : EMERGENCY Booting Mode
[16:30:57:705] : >>Get Model Name in Emergency Mode [DLOAD_VERREQ_F]
[16:30:57:721] : 76XXT-6040-TSNCJPLYMta\Local\Temp\DZE51
[16:30:57:721] : First two character of model name is not BS
[16:30:57:721] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 0 - No Phone
[16:30:57:721] : GetEmergencyModelName in Emergency Mode - FAILed (No Phone)
[16:30:57:721] : WM_COPYDATA ¸Þ½ÃÁö º¸³¿ 3 - Close Port
[16:30:57:721] : Close Port<<
[16:30:57:721] : TYPE_WPARAM_UPGRADE_ERROR
[16:30:57:752] : Log finished
then KDZ force closes .

;(
Yesterday, i've tried to go to recovery mode in powermenu [ROM CM7 nightly 1], but phone just stuck at lg logo. Then I've tried to unbrick it with KDZ. Something in first progress steps happened, and now my phone do not show any signs of life. Also I have no warranty.But i can fix it, i searched on every forum, and did not found anything, that would work. So is there any way i could unbrick my phone ?
Thanks
P.s.
And maybe i could fix it somehow using JTAG, but using arduino as that thing ? ( I don't have an arduino, but I am planing to have one)

It worked on my device , thank you:good:

error with kdz
upgrade error
WParam : 100
LParam : 500
pls help me guys

Related

[HOWTO] Phone not responding at all - last chance to repair

Hi, because with last update increased count of people with bricket phone, I just tryed search for way how to repair this phone. It seems, that last possible way how to save your phone is emergency mode.
I would like to notify you, that I didn't tested it (I'm had not luck enough to brick my phone yet ). I just searched and tried write this for help to others.
So, let's go on.
1) If it's not possible connect to phone via ADB (in Adroid SDK/tools run "adb shell") at all you will try next steps. If it will work, you can use another, verified tools like custom recovery or KDZ_FW_UPD (search on forum for more) [HOWTO] Flash original firmware on P500, )
2) If you fail in previous step, you can try enter into emergency mode manually and try to flash ROM with KDZ_FW_UPD:
Download KDZ updater and uncompress it
http://www.4shared.com/file/UleS4dP3/KDZ_FW_UPD_EN.html
Install msxml.msi from the uncompressed directory
Charge your battery to almost full state (I'm not sure, but it can be reason if phone doesn't start)
Turn phone off somehow (remove battery etc.)
Install drivers properly
Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments
Install the LG drivers by selecting the update manager from the lg site
Disable LGE Virtual Modem. In your Windows operating system, go to Control Panel > System > Hardware > Device Manager > Modems > Right click on LGE Virtual Modem and click Disable.
Press and keep pressed "Volume up"+"Return" and connect USB cable to phone
Yellow screen with text emergency mode should appeared
Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
Run KDZ_FW_UPD.exe (Has administrator).
Select Type : 3GQCT (I have one report that CDMA mod works too)
Select PhoneMode : DIAG (in case of fail try EMERGENCY, and as last chance use CS_EMERGENCY)
I Recommend do not switch phone off. There was some people, which done it and after they were not be able to turn it on again. If flashing failed, just select some another mode and try it again, again, try shake/connect disconnect, again, again....
In KDZ file : Choose the ROM file you downloaded in the first step
Press Launch software update
Shake the handset (I know, it sounds ... strange, but it helps for ones, so... why don't try it?) UPDATE: Read some quotes on bottom.
Make sure that all update was done successfully. Phone should restart itself automatically
Disconnect the USB cable from the phone
Press the three button combo for HW reset of device i.e volume up + home + power button
List to do based on Zecanilis's [HOWTO] Flash original firmware on P500
3) Still no success? Wait for more "What I can do" or just go to LG and let repair on them.
Source:
http://forum.gsmhosting.com/vbb/f282/vygis-shell-v1-1-0-josedavido-1166478/ (included file named "Flash help.txt" in application)
http://android.modaco.com/content/l...modaco-com/321895/faq-gt540-reference-thread/
Please let me know if it works. I just searched for way and I haven't possibility to test this steps for now. I will do update if it will be necessary, same as I will try describe more about software which I founded.
Some experiences from thread(s):
AVanover5: ...It works if you set the mode to CDMA and DIAG. Just to let people know. Not sure if it'd work without the recovery screen or not. I never tried it ironically, haha. Thank you guys.
geejay2: ...Bricking seems to be easily achieved by forgetting to disable the LG Modem driver. Apparently the modem driver interferes during flashing. Also I noted that kdz is not stable under Win2k, I switched to WinXP to flash successfully. I saw several aborted flashing attempts in WinXP with modem driver enabled.
domenic_s:KDZ_FW_UPD doesn't work (Application cannot start) -.- Using Windows 7 64bit version. //edit: allright tried another pc (win xp 32bit) and yeah - it worked... I'm so happy.
Click to expand...
Click to collapse
About shaking (sorry, but I still can't believe... )
salte_eskil:wow! shaking the phone really worked! seems kind of stupid but thanks to you all at the xda forum for tips and tricks
4wd vege: Now unbricked. Strangely kdz updater only saw my phone after shaking!!!
me2kimi:It sound crazy to shake the phone while at emergency mode. I's crazy but it magic. ...So what I do is connect to usb, Launch software update at kdz while shaking the phone. Then after that kdz is working like normal.
Click to expand...
Click to collapse

I tried with all possible combination.. with and without battery.. vol- home, vol + return, power vol+ home.. end more.. but phone don't turn on...
In meantimes the phone is in the service LG.. hope...
Exscuse me for my English

Did you had phone off before trying this? And also battery should be charged. I just added this things...
If event that it not show you emergency mode, LG service and warranty is probably the only way how to proceed. Sorry. But I will be searching if another way will exist...

Good work .. I hope that you will find a way to solve ... especially for other users .. good luck

Good work @The_ERROR.
It should work. I think you should also add that the phone mode should be set to Emergency (and not DIAG as mentioned) in the kdz updater.

Moved to development and stickied it for a while!
Thank you!
Cheers

socialdistortion said:
Good work @The_ERROR.
It should work. I think you should also add that the phone mode should be set to Emergency (and not DIAG as mentioned) in the kdz updater.
Click to expand...
Click to collapse
Good to know - do you know differences between CS_EMERGENCY and EMERGENCY?

Recovery Phone?!
Hello,
Had anyone tried "Recovery Phone" from the LGMobile Update app? It's under the "Customer Support" menu. Enter IMEI or S/N and see if it can bring it up to life.
Cheers.

Yes.. I tried.. but nothing.. the LG MOBILE UPDATE crashed because don't wiew the phone in Usb...

zeule said:
Hello,
Had anyone tried "Recovery Phone" from the LGMobile Update app? It's under the "Customer Support" menu. Enter IMEI or S/N and see if it can bring it up to life.
Cheers.
Click to expand...
Click to collapse
I can add that as next possible way Let me expect it.

batman89i said:
Yes.. I tried.. but nothing.. the LG MOBILE UPDATE crashed because don't wiew the phone in Usb...
Click to expand...
Click to collapse
So... it sad everything

The_ERROR said:
Good to know - do you know differences between CS_EMERGENCY and EMERGENCY?
Click to expand...
Click to collapse
Not really. Gathered some info though. We use emergency mode when the phone boots into only emergency mode else we try CS emergency as last option.
In any case this method will work only if the kdz updater recognises the phone.
Further reading http://android.modaco.com/content/lg-gt540-optimus-gt540-modaco-com/321895/faq-gt540-reference-thread/

I was able to do the KDZ, actually thats the only way possible. Please add this to the list:
1. Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments.
2. Install the LG drivers by selecting the update manager from the lg site.
3. Disable the modem driver.
4. Once done, reboot the handset and when it has come to emergency mode connect it via USB.
5. Its going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
6. shake the handset - IT DID WORKED FOR ME.
My suggestion don't give up. It took me around 14 hours to bring the handset back to original firmware and here I am today trying to boot the rom once again.
7. UPDATE AND ENJOY.

pariksheetsharma said:
I was able to do the KDZ, actually thats the only way possible. Please add this to the list:
1. Get rid of all usb drivers like Nokia, microsoft visual ++ run time environments.
2. Install the LG drivers by selecting the update manager from the lg site.
3. Disable the modem driver.
4. Once done, reboot the handset and when it has come to emergency mode connect it via USB.
5. Its going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
6. shake the handset - IT DID WORKED FOR ME.
My suggestion don't give up. It took me around 14 hours to bring the handset back to original firmware and here I am today trying to boot the rom once again.
7. UPDATE AND ENJOY.
Click to expand...
Click to collapse
Thanks, I will do!! Only about 4 and five.
First reboot the handset and when it has come to emergency mode connect it via USB
and then
It's going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
So, whats about if phone didn't go into emrgency itself (for example stuck on Android logo)?

The_ERROR said:
Thanks, I will do!! Only about 4 and five.
First reboot the handset and when it has come to emergency mode connect it via USB
and then
It's going to detect it as usb drive. Launch KDZ. No need to go into Emergency mode.
So, whats about if phone didn't go into emrgency itself (for example stuck on Android logo)?
Click to expand...
Click to collapse
I am talking about phone getting into Emergency mode, KDZ doesn't need to switch to CS_EMERGENCY or EMERGENCY Switch off the phone first, then you are either connect it to USB cable or you can remove it from the USB cable. Key combination to bring the phone only in emergency mode are:
1. Connected to USB cable, only thing visible is the LG logo, this is because its getting charged. Press VOL UP + BACK BUTTON
2. Not connected to USB cable and is not charging and so switched off: Press VOL UP + BACK BUTTON + POWER BUTTON
In both the cases phone will switch to a yellow screen showing: "Emergency mode!!" and will remain like that.
It's only in Emergency mode that the handset will be detected like a USB drive and can be KDZed.

I seriously doubt the "Shake your phone part". It just sounds so ...
Peace

pariksheetsharma said:
I am talking about phone getting into Emergency mode, KDZ doesn't need to switch to CS_EMERGENCY or EMERGENCY Switch off the phone first, then you are either connect it to USB cable or you can remove it from the USB cable. Key combination to bring the phone only in emergency mode are:
1. Connected to USB cable, only thing visible is the LG logo, this is because its getting charged. Press VOL UP + BACK BUTTON
2. Not connected to USB cable and is not charging and so switched off: Press VOL UP + BACK BUTTON + POWER BUTTON
In both the cases phone will switch to a yellow screen showing: "Emergency mode!!" and will remain like that.
It's only in Emergency mode that the handset will be detected like a USB drive and can be KDZed.
Click to expand...
Click to collapse
OK, I edited it. But I kept possibilities of EMERGENCY and CS_EMERGENCY modes if standard way failed. About switch into emergency, I think that it does not matter which way for emergency is used.

socialdistortion said:
I seriously doubt the "Shake your phone part". It just sounds so ...
Peace
Click to expand...
Click to collapse
Yes, I know... but if it will help, it doesn't matter how stupid it sounds....

Stuck in LG logo, unable to boot into emergency mode.
What can I do? Go to LG?

cjbi said:
Stuck in LG logo, unable to boot into emergency mode.
What can I do? Go to LG?
Click to expand...
Click to collapse
Have you tried all the mentioned methods? Press the combination buttons a little longer (Maybe that can help).
BTW what did you do that bricked your phone?

Bricked LG P350

I have one P350 and guy told me that it's flashed with "wrong" firmware.
Now it's totaly dead.
I was try to conect it to PC but nothing.
I was try vol up + vol down and connect USB but nothing.
Any help?
Thanks.

Can you do anything with it at all? For example turn it on?
Sent From This Thing Called An 'EVO 3D'

No it's totaly dead. Won't turn on, don't go to recovery mode. Nothing.
I was reading something about Medusa box and JTAG repair.

plavush said:
I have one P350 and guy told me that it's flashed with "wrong" firmware.
Now it's totaly dead.
I was try to conect it to PC but nothing.
I was try vol up + vol down and connect USB but nothing.
Any help?
Thanks.
Click to expand...
Click to collapse
Have you tried with fastboot mode? I recently bricked my lg p350 and recovery mode wasn‘t working but i was able to restore everything.
Sent from my LG-P350 using XDA App

I'm noob with that LG can you please tell me how to try that fastboot?

You need first to go in fastboot mode: from phone off you press button to start call + vol up + power button. After a bit should start the phone in fastboot mode and you need to install android sdk to be able to use adb. You should search on internet for more detailed informations.
Sent from my LG-P350 using XDA App

I was try all combination that i was found. HOME+VOL UP , CALL+VOL UP, MENU+VOL UP, VOL UP+VOL DOWN with POWER and without POWER but no luck. Nothing shown on mobile and i was try all of that with cable and computer don't recognize phone in any mode. :-(

another bricked p350
hi,plavush,i recently bricked my p350 too and he remain death no metter what i do. please ,if you have some clue how to repair it,please ,thank you.

plavush said:
I was try all combination that i was found. HOME+VOL UP , CALL+VOL UP, MENU+VOL UP, VOL UP+VOL DOWN with POWER and without POWER but no luck. Nothing shown on mobile and i was try all of that with cable and computer don't recognize phone in any mode. :-(
Click to expand...
Click to collapse
AFAIK unless you have an hardware problem if you mess up with recovery you should switch off the phone (To unsure that take off the battery and put it back) and keep pressed VOL UP+CALL and POWER until you see fastboot mode appear with few messages:
Fastboot mode started
udc_start()
It should work. At least it worked for me.
Cheers,
Gabriele

help needed
hey wat to do after that ?? i connect it to my ubuntu system and the messages of "-- suspend -- -- reset -- etc" comes up...
i am not able to communicate the phone with my laptop
ex : doing "fastboot erase recovery" just shows <waiting for device>
is there something i can tweak to make my phone to communicate with my ubuntu system... ? please help !

solved
just wrote the fastboot commands in sudo mode and it worked !

I have the same problem i tried to put custom rom on my p350 but something went wrong ,
Now i can go to fastboot mode and recovery too but i don't know what to do after that ( noob ) xD
What can i do with my PC how to unbrick my phone help me please !!!!
@jaypanda i have dual boot windows and ubuntu so if you unbricked your phone with ubuntu please tell me how to do so

SOLUTION
Ok i find the solution for this problem , for those who want to UNBRICK LG OPTIMUS ME P350 folow this short tutorial:
1.Download official lg optimus me firmware:
2.Download Kdz updater:
3.Download LG Optimus Me Drivers :
After downloading all files from above folow these steps :
1.Install all lg optimus me drivers from step 3. above
2. After instaling the drivers go to Device manager ( for windows users only )
3.Disable all LGE modem drivers (and restart your PC if u want
4.Extract KDZ_FW_UPD_EN.7z ( that you downloaded in step 2. )
5. After extracting from extracted file install msxml.msi FiRST
6. Put your phone to emergency mode to do so remove battery and put it back in the fone , then hold Volume up and Volume down buttons and power button ( hold all those buttons at the same time )
7. If you done with the step 6. on your phone screen you will see yelow background , thats good
8.plug your phone with Usb cable to your PC
9.Start KDZ_FW_UPD.exe that you downloaded and extracted in step 4.
10. choose settings : Type: 3GQCT Mode: DIAG
11.Choose your firmware that you downloaded
12. Finaly click "Launch Software Update"
13. Wait for process to finish , after that unplug your phone and power it up
OPTIONAL: If the KDZ_FW_UPD.exe won't recognize your phone remove SD Card from your phone or try to install Drivers once again , keep trying until KDZ_FW_UPD.exe recognize your phone
This tutorial work 100 % and i tested it !
Because i'm new member to the forum im not aloved to put links for downloading , if you need files for this tutorial contact me via PM , i will put the download links as soon as i get rights to do so
Good luck
P.S. Sorry about my bad English xD

^^
thanx man, you totally saved me

I'm glad i can help

hi, i have same problem with wrong fimware on my p350... but i was unable to turn it on in anny way... pls what should i doo? is there anny other solution

but my phone wont even show yelow screen

kenai666, a hard reset button does?

Hi I PM'ed u but u havent replied could you please reply or email me the links at [email protected]
mtssrbija said:
Ok i find the solution for this problem , for those who want to UNBRICK LG OPTIMUS ME P350 folow this short tutorial:
1.Download official lg optimus me firmware:
2.Download Kdz updater:
3.Download LG Optimus Me Drivers :
After downloading all files from above folow these steps :
1.Install all lg optimus me drivers from step 3. above
2. After instaling the drivers go to Device manager ( for windows users only )
3.Disable all LGE modem drivers (and restart your PC if u want
4.Extract KDZ_FW_UPD_EN.7z ( that you downloaded in step 2. )
5. After extracting from extracted file install msxml.msi FiRST
6. Put your phone to emergency mode to do so remove battery and put it back in the fone , then hold Volume up and Volume down buttons and power button ( hold all those buttons at the same time )
7. If you done with the step 6. on your phone screen you will see yelow background , thats good
8.plug your phone with Usb cable to your PC
9.Start KDZ_FW_UPD.exe that you downloaded and extracted in step 4.
10. choose settings : Type: 3GQCT Mode: DIAG
11.Choose your firmware that you downloaded
12. Finaly click "Launch Software Update"
13. Wait for process to finish , after that unplug your phone and power it up
OPTIONAL: If the KDZ_FW_UPD.exe won't recognize your phone remove SD Card from your phone or try to install Drivers once again , keep trying until KDZ_FW_UPD.exe recognize your phone
This tutorial work 100 % and i tested it !
Because i'm new member to the forum im not aloved to put links for downloading , if you need files for this tutorial contact me via PM , i will put the download links as soon as i get rights to do so
Good luck
P.S. Sorry about my bad English xD
Click to expand...
Click to collapse

I sended all files on PM CHECK PM
Sent from my Optimus Me using XDA App

[Q] Phone bricked, stuck at LG logo. Failed at flashing custom recovery image.

I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?

This happened to me also. I solved it like this:
First thing to do is get sure the LG drivers are installed ( there is a topic in the forum on this also).
Install KDZ ( serch in the forum and download it)
Download a room ( stock or not )
Flash the phone with KDZ ( after the drivers have been installed the phone should be detected on the pc.
After flashing if it does not start up do not fear, get the battery out, re install the battery and do a hard reset power+home+volume down buttons pressed at the same time and it should work.
If its your first time install Stock GB 20E as it is an open room, if not new to this I would suggest CM7.
Hope it helped
Regards

But the PC doesn't recognize the phone.
Here is the log from KDZ:
[R&D Test Tools Log File]
23:47:37 : Launching SW update
23:47:37 : Unpacking KDZ
23:47:39 : KDZ file extraced
23:47:40 : Files were extracted.
23:47:40 : LGMobileDL Load.
23:47:40 : Port = -1
23:47:40 : Connecting to phone
23:47:40 : PHONE WAS NOT FOUND!
23:47:42 : ===FINISHED===
Click to expand...
Click to collapse
How should I solve this problem? :/

bondzi said:
But the PC doesn't recognize the phone.
Here is the log from KDZ:
How should I solve this problem? :/
Click to expand...
Click to collapse
I had this same issue too, do not worry.
Keep your phone plugged into your computer, and go to Start > Control Panel > System > Hardware > Device Manager > Modems and disable the LG modem.
I am on Windows XP, so it may not be the same steps, but the point is that you have to disable the LG modem in Device Manager.

I had the same problem as well at one point. What operating system are you running on your computer?
I had the same issue, but I could not find the LG modem to disable it, it was just that windows was not detecting my phone at all, or using the drivers I had installed for my P500 to figure out what was connected to my laptop. Bricked phone after a failed ROM flash. Reinstallation of USB drivers for my phone failed to do anything.
Have you used LG Mobile update at all? I got all my drivers through it, rather than useless PC Suite 4.
Download it through HERE
Here's what I did to rectify it (Running windows vista):
DO NOT PLUG IN YOUR PHONE UNTIL STEP 3!
1. Went to system restore in windows(you'll find it under Backup and Restore in the Control Panel) and restore your computer to a state before installing any drivers for your phone.
2. After everything had completed, installed LG Mobile update. There is an option to install general USB drivers for your phone, DO NOT do it! Go to Customer Support > Application, Manual & USB driver download. Input your IMEI number from behind the battery in the back of your phone(or just select the "Read your phone" option if you can get it to read your phone). It will search and return the correct drivers for your exact phone. Download and install your USB drivers.
3. Keep your phone disconnected from your PC, and start up LG mobile update again. Connect your phone, LG mobile update should verify the connection by trying to connect to your phone, checking software versions, etc. It will connect even if you are stuck at the LG screen.
4. If everything checks out run KDZ updater and flash your phone back to original specs.

hey first go to emergency mode by pressing back(return) and volume up
and then in emergency mode use kdz it then only pc will recongnise your phone
believe me this thing also happens with me and I know that time I very scared
that time I used this article
http://forum.xda-developers.com/showthread.php?t=1015332

bondzi said:
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
Click to expand...
Click to collapse
read general thread it has been answered many times,stucking at lg logo is solved by take out battery reinsert and the 3 button combo
have u tried HOME + VOL DOWN +POWER BUTTON,still if it dont,
read downgrading details here http://forum.xda-developers.com/showthread.php?t=1038338
error guide here http://forum.xda-developers.com/showthread.php?t=883314

The same problem. But i solved it.
1) install again the driver using B2CAppSetup
2)This is based by xda forum by: Zecanills with a detailed explanation from my side.
- You need to download the firmware of your device. Download "Orginal LG Firmware" application (search in xda forum). Open it, put your IMEI and you will download the original ROM.
- Download KDZ updater and uncompress it
KDZ_FW_UPD_EN.zip - 4shared.com - online file sharing and storage - download
- Install msxml.msi from the uncompressed directory
3) Remove the battery, put it back and start the phone in emergency mode (actually the only way possible) back+up volume+power
Connect your device and run KDZ_FW_UPD.exe (as administrator). If the phone is not recognized repeat step 3) several times.
Select Type : 3GQCT
Select PhoneMode : DIAG
In KDZ file : Choose the ROM file you downloaded in the step 2)
Press Launch software update and wait (It will be 10 minutes or so).
Wait until it reboots.
After reboot will appear an image as in the following link: http://androidforums.com/getitnowmarketing/330813-all-one-recovery-thread.html
Don't worry. Restart phone again pushing power button (or remove battery, put it back and push power ) and then after few minutes you will have the phone as the begging when you bought it.

Thanks people for helping me. I just put the phone in emergency mode (Volume UP button + Home button), connected to the PC and flashed with KDZ.
After that, the phone works fine.
Thank you again!

bondzi said:
I flashed custom recovery image successfully and after that, when phone has to restart, it just stuck at LG logo.
When I tried to enter in custom recovery menu, but it shows only LG logo.
I tried to connect with PC, but it was unsuccessfully. The PC doesn't recognize the device. (nothing happens).
Can anyone help me?
Click to expand...
Click to collapse
man i am new as this thing
my lg is p925 and i didnot know that after i install root kdz for p920 and when i run rom maneger i did not find my model lg p925 so i tryed the res of the lest in rom maneger
bad move..........one of them is about lisen or somthing like that....but when i restart my phone frezzzz in lg logo ...i went to recovery mode (vol dwn+power)and all list about wiping no install zip in sd so i tryd (vol up+connect to pc) works so i use lg update an it says i have last apdate then i tryd cs>recovery with imei number but it says model not spport s/w....what must i do..dose flash it will hilp me? plzzzzzzzzzzzzz hilppppppppppp

LG P925
Same thing happened to me! I'm desperate... I've done research for hours and tried everything but no success so far... anyone could help us?
88prince said:
man i am new as this thing
my lg is p925 and i didnot know that after i install root kdz for p920 and when i run rom maneger i did not find my model lg p925 so i tryed the res of the lest in rom maneger
bad move..........one of them is about lisen or somthing like that....but when i restart my phone frezzzz in lg logo ...i went to recovery mode (vol dwn+power)and all list about wiping no install zip in sd so i tryd (vol up+connect to pc) works so i use lg update an it says i have last apdate then i tryd cs>recovery with imei number but it says model not spport s/w....what must i do..dose flash it will hilp me? plzzzzzzzzzzzzz hilppppppppppp
Click to expand...
Click to collapse

[Guide]Revert To Stock With LG Software(Easy)

So many people around here are having issues with KDZ, errors such as:
--Connections problem between PC and Phone
-Drivers problem.
-Cannot find the phone.
-Bricked too hard.
-Random chinese info stuff...How did i find this solution ?
After i copied the wrong aboot.bin to my device KDZ stopped working even after i repaired it.Why did i try to use KDZ after i repaired it?Well because i bricked it again by installing some modules that weren't compatible and it ended by deleting some of my system apps and also my navigation bar.So, i thought myself why LG designed an program for software update and why don't we use it?So i used B2CAppSetup, and not only that it fixed my device but also it reverted the firmware that i lost when i bricked my phone first time, because when i bricked it the first time i couldn't find the same KDZ i just flashed one that seemed compatible.I have to say it was way more faster and easier.
Click to expand...
Click to collapse
Let's get to the guide shall we?
Step 1 : Download B2CAppSetup( i attached it for ya )
Step 2a : Install it !
Warning Step 2 : If you already have KDZ installed using @hyelton method DON'T INSTALL IT!, you should already have it in your KDZ folder .
Step 2b (If you already have KDZ installed using @hyelton method and can't find B2CAppSetup) : Just delete it and install the program from here .
Step 3 : Open the program and plug your phone into the PC/Laptop whatever.
Step 3.1a: If you can boot up your phone( i mean if it's not bricked ) just select Software LG mode and in the B2CAppSetup window there should appear something like "Your phone has been discovered, do you want to install the driver?", you would say Yes and wait until the driver is installed.
Additional Info for Step 3.1a : For B2CAppSetup to find your phone you don't need only to have the Software LG mode enabled, you will also need the driver that should automatically install by itself.
Step 3.1b:If your device is bricked and can't boot you'll have to enter the Download Mode, to do that just keep holding the Vol. Up button while inserting the USB cable in the phone( The USB cable must be already plugged into the PC while doing that), and you keep it until you go into the Download Mode.
Step 4 : Now let's get the upgrade done. So basically since our phone has no firmware updates we have to trick the program. In the upper right corner you should see two options available, you are going to click on the one that says "Additional Functions"( the one in the left) and then select the second options that says something like "Recovery from an update error".
Step 5 : Now if you've followed as i've said it should be very easy from now on.The program will connect to the device and start downloading the right Firmware Update that you had when your phone first came.
WARING !!! : DURING THE INSTALLATION THE PROGRAM MAY GIVE YOU THIS ERROR " The device has been disconnected from the PC, do you want to abort the update" , you just let it that way because it will still be installing even if that error pops-up.
Step 5.1 : When the installation reaches like 80% your phone should boot up, but don't disconnect it yet, just wait until the program crashed itself,it should crash when it's 99%, after that you can unplug it.
Errors after installing:
1 )com.android.phone has stopped responding
2 )acore has stopped...
3 )contacts has stopped...
n )......
( and it keeps saying that without stopping and letting you do anything )
To fix it just, do a hard reset by using the stock recovery. Hope this method helped you in any way since the links where we could download the KDZ files are mostly down and since the KDZ works when it want and how it want.Feel free to ask question.This method was tested on the D620.

... and then select the second options that says something like "Recovery from an update error".
Click to expand...
Click to collapse
This is where the option should be .

hi
Rephosix said:
So many people around here are having issues with KDZ, errors such as:
--Connections problem between PC and Phone
-Drivers problem.
-Cannot find the phone.
-Bricked too hard.
-Random chinese info stuff...How did i find this solution ?
Let's get to the guide shall we?
Step 1 : Download B2CAppSetup( i attached it for ya )
Step 2a : Install it !
Warning Step 2 : If you already have KDZ installed using @hyelton method DON'T INSTALL IT!, you should already have it in your KDZ folder .
Step 2b (If you already have KDZ installed using @hyelton method and can't find B2CAppSetup) : Just delete it and install the program from here .
Step 3 : Open the program and plug your phone into the PC/Laptop whatever.
Step 3.1a: If you can boot up your phone( i mean if it's not bricked ) just select Software LG mode and in the B2CAppSetup window there should appear something like "Your phone has been discovered, do you want to install the driver?", you would say Yes and wait until the driver is installed.
Additional Info for Step 3.1a : For B2CAppSetup to find your phone you don't need only to have the Software LG mode enabled, you will also need the driver that should automatically install by itself.
Step 3.1b:If your device is bricked and can't boot you'll have to enter the Download Mode, to do that just keep holding the Vol. Up button while inserting the USB cable in the phone( The USB cable must be already plugged into the PC while doing that), and you keep it until you go into the Download Mode.
Step 4 : Now let's get the upgrade done. So basically since our phone has no firmware updates we have to trick the program. In the upper right corner you should see two options available, you are going to click on the one that says "Additional Functions"( the one in the left) and then select the second options that says something like "Recovery from an update error".
Step 5 : Now if you've followed as i've said it should be very easy from now on.The program will connect to the device and start downloading the right Firmware Update that you had when your phone first came.
WARING !!! : DURING THE INSTALLATION THE PROGRAM MAY GIVE YOU THIS ERROR " The device has been disconnected from the PC, do you want to abort the update" , you just let it that way because it will still be installing even if that error pops-up.
Step 5.1 : When the installation reaches like 80% your phone should boot up, but don't disconnect it yet, just wait until the program crashed itself,it should crash when it's 99%, after that you can unplug it.
Errors after installing:
1 )com.android.phone has stopped responding
2 )acore has stopped...
3 )contacts has stopped...
n )......
( and it keeps saying that without stopping and letting you do anything )
To fix it just, do a hard reset by using the stock recovery. Hope this method helped you in any way since the links where we could download the KDZ files are mostly down and since the KDZ works when it want and how it want.Feel free to ask question.This method was tested on the D620.
Click to expand...
Click to collapse
what if you can't get in download mode because you're device hasn't got usb debugging anabled ?
my stays just black i only rooted, didn't put anything yet on it , it does connect to my pc but only like a folder with media in it but i can't get in recovery nor download mode could you help me ? it's a lg g2 mini

Teamsvg said:
what if you can't get in download mode because you're device hasn't got usb debugging anabled ?
my stays just black i only rooted, didn't put anything yet on it , it does connect to my pc but only like a folder with media in it but i can't get in recovery nor download mode could you help me ? it's a lg g2 mini
Click to expand...
Click to collapse
Well, this is a guide on how to reflash the stock version in case KDZ is not working, i guess if the USB still recognizes the phone it may be a chance to work, just attempt to use the software and see if it works (after all this is another method beside KDZ)

Rephosix said:
So many people around here are having issues with KDZ, errors such as:
--Connections problem between PC and Phone
-Drivers problem.
-Cannot find the phone.
-Bricked too hard.
-Random chinese info stuff...How did i find this solution ?
Let's get to the guide shall we?
Step 1 : Download B2CAppSetup( i attached it for ya )
Step 2a : Install it !
Warning Step 2 : If you already have KDZ installed using @hyelton method DON'T INSTALL IT!, you should already have it in your KDZ folder .
Step 2b (If you already have KDZ installed using @hyelton method and can't find B2CAppSetup) : Just delete it and install the program from here .
Step 3 : Open the program and plug your phone into the PC/Laptop whatever.
Step 3.1a: If you can boot up your phone( i mean if it's not bricked ) just select Software LG mode and in the B2CAppSetup window there should appear something like "Your phone has been discovered, do you want to install the driver?", you would say Yes and wait until the driver is installed.
Additional Info for Step 3.1a : For B2CAppSetup to find your phone you don't need only to have the Software LG mode enabled, you will also need the driver that should automatically install by itself.
Step 3.1b:If your device is bricked and can't boot you'll have to enter the Download Mode, to do that just keep holding the Vol. Up button while inserting the USB cable in the phone( The USB cable must be already plugged into the PC while doing that), and you keep it until you go into the Download Mode.
Step 4 : Now let's get the upgrade done. So basically since our phone has no firmware updates we have to trick the program. In the upper right corner you should see two options available, you are going to click on the one that says "Additional Functions"( the one in the left) and then select the second options that says something like "Recovery from an update error".
Step 5 : Now if you've followed as i've said it should be very easy from now on.The program will connect to the device and start downloading the right Firmware Update that you had when your phone first came.
WARING !!! : DURING THE INSTALLATION THE PROGRAM MAY GIVE YOU THIS ERROR " The device has been disconnected from the PC, do you want to abort the update" , you just let it that way because it will still be installing even if that error pops-up.
Step 5.1 : When the installation reaches like 80% your phone should boot up, but don't disconnect it yet, just wait until the program crashed itself,it should crash when it's 99%, after that you can unplug it.
Errors after installing:
1 )com.android.phone has stopped responding
2 )acore has stopped...
3 )contacts has stopped...
n )......
( and it keeps saying that without stopping and letting you do anything )
To fix it just, do a hard reset by using the stock recovery. Hope this method helped you in any way since the links where we could download the KDZ files are mostly down and since the KDZ works when it want and how it want.Feel free to ask question.This method was tested on the D620.
Click to expand...
Click to collapse
All models work download
My model does not work D620R Why not falling
I want to go back to Original rom of LG

Nice Tutorial
Luckily I don't need it yet, but I'm sure I'll need in some time in the futur

Works
For me it worked perfectly . I had Cyanogen but restore to stock failed from backup.
So :
1. Downloaded B2CAppSetup and installed
2. Downloaded LG United Mobile Driver Ver. 3.10
3. With UP button pushed I inserted the usb cable . Got into Download Mode.
4. From LG mobile support tool I choose Options -> Update Recovery
5. Waited to complete, phone booting, hard reset

haimmalka said:
All models work download
My model does not work D620R Why not falling
I want to go back to Original rom of LG
Click to expand...
Click to collapse
Same happend to me but I downloaded and installed driver from LG .

If my phone has a cab file will it convert it to kdz for me

I'm having the same issues. My LG G2 Mini D618 is stuck in the LG logo
I can't seem to enter Download mode even though I follow the instruction (press volume up button as I plug the USB cable) and installed USB drivers. Please help!

Hi guys,
Sorry to revive the old post, but I haven't been able to find me a solution after many days searching... A customer came to me with an LG G2 Mini D625 (located in Chile), for what i've been investigating the phone is stuck in APX mode, I got to install the "NVIDIA USB Boot-recovery driver for Mobile devices", and now I'm trying this method to attempt to revive the phone... however it has come to my attention that after:
1. Removing the battery
2. Keeping pressed vol+
3. Connecting the usb cable to phone & pc while doing step 2
I can't get the phone to boot in Download mode... Could it be it's a different method for D625? Is it plain dead & hard-bricked without any options left? Can something be done with some sort of box? I don't have any type of box myself, but if needed be, I can advise my customer to go with another technician who owns a box...
EDIT: I have the phone with me... just FYI

Tcl m3g maybe brick

Hello
excuse my English please ,cause i'm french man
I had a tcl m3g chinise rom miui ,root
The phone propose me an update on ota
i accept and and now its impossible to restart my phone
i plug it to my pc and it says unknow device with 5 disk detected
Py pc says that i must formated them to work
i do that and know its horrible
impossible to restart my phone,no drivers work .no recovery mode ,no download mode etc...
can you help me ,please

Hi, I happen to have the same phone and something similar happened to me but with a CM12.1 Moke rom, the phone was working fine but it turned off twice randomly, I connected it to the wallcharger and the PC but nothing happened, the 5 USB units appeared too on my computer so I had to keep the power button pressed for 10 seconds to force a reboot and the system loaded fine, though I went back to another CM12.1 rom. Try doing that, keep the power button pressed for 10 seconds and see if that forces a reboot.

Hi
I've tried to keep the power button pressed but nothing append.

dano33 said:
Hello
excuse my English please ,cause i'm french man
I had a tcl m3g chinise rom miui ,root
The phone propose me an update on ota
i accept and and now its impossible to restart my phone
i plug it to my pc and it says unknow device with 5 disk detected
Py pc says that i must formated them to work
i do that and know its horrible
impossible to restart my phone,no drivers work .no recovery mode ,no download mode etc...
can you help me ,please
Click to expand...
Click to collapse
hello , I also have the same problem . What did you do with your phone ? fix it? and how? help me please ..

- Download the DiskGenius
- connect the phone to a computer via USB (best to use the connector on the rear panel, and even better to use a laptop, there is the battery and if the lights go out, you are protected)
- in the Device Manager (Windows) will be Qualcomm HS-USB QDLoader 9006 (COMx ) - if not, click the + and - volume, along with the power button, the appearance, let go first and then the power and volume buttons. If you do not appear, it means you have not installed drivers Qualcomm (in the cap is, install)
- run DiskGenius (be careful! You get access to all the connected drives, do not remove too much!))
- Delete partitions SBL1 (Right-click to select the recycle symbol ), confirm the removal (Yes) to apply your changes (the first icon in the menu, vaguely reminiscent of the character Commander floppy or Total).
- disconnected and reconnected body to USB, and lo and behold - found new hardware, Windows itself installs the necessary drivers. In Device Manager, we see Qualcomm HS-USB QDLoader 9008 (COMx)
- sewn factory Lewa4.0 using QPST (full instructions in the topic, I will not be added)
- After the firmware disable the body for a long time (5-10-15 seconds) click on the button supply. We see native boot anim Hooray !!! (translated from 4pda.ru)
Original chinese tutorial:
bbs.ydss.cn/thread-524446-1-1 . html (translate it and give it a go)
Good Luck
---------- Post added at 01:29 PM ---------- Previous post was at 01:19 PM ----------
yilmazco said:
hello , I also have the same problem . What did you do with your phone ? fix it? and how? help me please ..
Click to expand...
Click to collapse
Tool:
yadi.sk/d/GvPjkXFli8u9S

yilmazco said:
hello , I also have the same problem . What did you do with your phone ? fix it? and how? help me please ..
Click to expand...
Click to collapse
sorry for the trouble, as you did at the end to fix it?

TCL m3g .qcn file
alberto00 said:
sorry for the trouble, as you did at the end to fix it?
Click to expand...
Click to collapse
Hi,
Accidentally, I wiped all data of TCL m3g and somehow, I managed to bring the phone alive. But it seems like qcn file is totally corrupted and phone networks are no more identified. IMEI, ESN & MEID are all zeroes now.
Can any body provide .qcn file of TCL m3g?
Thanks

Here is the restart Solution
dano33 said:
Hello
excuse my English please ,cause i'm french man
I had a tcl m3g chinise rom miui ,root
The phone propose me an update on ota
i accept and and now its impossible to restart my phone
i plug it to my pc and it says unknow device with 5 disk detected
Py pc says that i must formated them to work
i do that and know its horrible
impossible to restart my phone,no drivers work .no recovery mode ,no download mode etc...
can you help me ,please
Click to expand...
Click to collapse
To restart your device you have to hold the power button + volume down button for 30-45 seconds.
It will restarts automatically...

vivixa said:
Hi,
Accidentally, I wiped all data of TCL m3g and somehow, I managed to bring the phone alive. But it seems like qcn file is totally corrupted and phone networks are no more identified. IMEI, ESN & MEID are all zeroes now.
Can any body provide .qcn file of TCL m3g?
Thanks
Click to expand...
Click to collapse
The same thing for me. I canÂ´t connect to any network. Tried different cards.
Please post the qcn file.

Tcl M3g bricked
I'm also have the same problem . How to go recovery mode?

how to save changes
xamixmix said:
- Download the DiskGenius
- connect the phone to a computer via USB (best to use the connector on the rear panel, and even better to use a laptop, there is the battery and if the lights go out, you are protected)
- in the Device Manager (Windows) will be Qualcomm HS-USB QDLoader 9006 (COMx ) - if not, click the + and - volume, along with the power button, the appearance, let go first and then the power and volume buttons. If you do not appear, it means you have not installed drivers Qualcomm (in the cap is, install)
- run DiskGenius (be careful! You get access to all the connected drives, do not remove too much!))
- Delete partitions SBL1 (Right-click to select the recycle symbol ), confirm the removal (Yes) to apply your changes (the first icon in the menu, vaguely reminiscent of the character Commander floppy or Total).
- disconnected and reconnected body to USB, and lo and behold - found new hardware, Windows itself installs the necessary drivers. In Device Manager, we see Qualcomm HS-USB QDLoader 9008 (COMx)
- sewn factory Lewa4.0 using QPST (full instructions in the topic, I will not be added)
- After the firmware disable the body for a long time (5-10-15 seconds) click on the button supply. We see native boot anim Hooray !!! (translated from 4pda.ru)
Original chinese tutorial:
bbs.ydss.cn/thread-524446-1-1 . html (translate it and give it a go)
Good Luck
---------- Post added at 01:29 PM ---------- Previous post was at 01:19 PM ----------
Tool:
yadi.sk/d/GvPjkXFli8u9S
Click to expand...
Click to collapse
after deleting partition sbl1 how to save the changes diskgenius is asking for licence

My phone is totally bricked after I deleted the partition and saved. Now it is not turning on, no bootloader or recovery or anything. Only the LED light turns on when I connect to charger or USB. Not detected in devise manager either. Please help.

I get my phone bach to life by flashing the emax mini files. But now i didn't get any network. Please post the qcn file for the TCL.

dano33 said:
Hello
excuse my English please ,cause i'm french man
I had a tcl m3g chinise rom miui ,root
The phone propose me an update on ota
i accept and and now its impossible to restart my phone
i plug it to my pc and it says unknow device with 5 disk detected
Py pc says that i must formated them to work
i do that and know its horrible
impossible to restart my phone,no drivers work .no recovery mode ,no download mode etc...
can you help me ,please
Click to expand...
Click to collapse
first you have to download your stock rom
than you can get into download mode by holding volume down button + power button for a while apx 35 to 60 seconds, As soon as getting vibration hold volume up button by holding them both....
Enjoy....

Better Mobile App

welcome