Hi,
I have an Xperia X10 with Cyagenmod 6 (gingerbread 2.3.3) but it's broken. It won't boot any more. Some days ago it just went out, and it won't start up again. The phone behaves as if it freezes the moment android should load. Like if your computer would freeze in bios, unable to load your operating system.
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
I am kind of a noob with these things and therefore hope one of you guys could help me out. I'm not really looking foreward te buying a new phone already
Thanks!
Freekh
kinda same problem..
i'm removing battery, put back and after holding power the phone shows green led for short time and vibrates for a sec and that's.
add:
i've flashed it before the problem occurs.. flashed, phone booted up, everything normal.. put on usb for charging, changed language and time when it suddenly freezed
This is what happened to mine what country u in
sent with a geordie kiss using wb 2.3.3
what do you mean with "country"?
freekh said:
Hi,
I have an Xperia X10 with Cyagenmod 6 (gingerbread 2.3.3) but it's broken. It won't boot any more. Some days ago it just went out, and it won't start up again. The phone behaves as if it freezes the moment android should load. Like if your computer would freeze in bios, unable to load your operating system.
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
I am kind of a noob with these things and therefore hope one of you guys could help me out. I'm not really looking foreward te buying a new phone already
Thanks!
Freekh
Click to expand...
Click to collapse
Try re-flashing the stock rom using flashtool. That solves Every problem for me ^^
freekh said:
Hi,
...
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
...
Click to expand...
Click to collapse
not able to flash anything
blmn1337 said:
not able to flash anything
Click to expand...
Click to collapse
Why exactly are u unable to flash anything? Are you following the proper procedure?
Here's a guide fro using flashtool http://forum.xda-developers.com/showthread.php?p=10879507#post10879507
fawadmir said:
Why exactly are u unable to flash anything? Are you following the proper procedure?
Here's a guide fro using flashtool http://forum.xda-developers.com/showthread.php?p=10879507#post10879507
Click to expand...
Click to collapse
i've posted some logs in other thread
http://forum.xda-developers.com/showthread.php?t=1190540&page=2
umm.. Do u move your mobile when the flashing process is going on? The xperia USB slot is pretty sensitive. Moving the phone can cause it to lose connection and abort the flashing process
28/048/2011 21:48:10 - ERROR - Error flashing. Aborted
i always receive this error if i move my phone.
Notice if you hear the USB device unplug sound from your PC before this error occurs.
^^
fawadmir said:
umm.. Do u move your mobile when the flashing process is going on? The xperia USB slot is pretty sensitive. Moving the phone can cause it to lose connection and abort the flashing process
28/048/2011 21:48:10 - ERROR - Error flashing. Aborted
i always receive this error if i move my phone.
Notice if you hear the USB device unplug sound from your PC before this error occurs.
^^
Click to expand...
Click to collapse
it doesnt seem to be a connection-problem (no usb unplug sounds).
it seems that the phone is in a state, where bootup is not possible
But the phone is not required to boot during flashing. Did you try changing the USB slot on your PC? The one you're connecting your phone to? Try another slot. Sometimes that works too.
fawadmir said:
But the phone is not required to boot during flashing. Did you try changing the USB slot on your PC? The one you're connecting your phone to? Try another slot. Sometimes that works too.
Click to expand...
Click to collapse
same result. can't flash
Me too. Can't flash with Flashtool (latest version), even without moving my phone. It starts flashing, but the progress bar shows of no progress. After a while it just says Error - Abort Flashing. I tried all of my USB port, but nothing changes.
after doing and trying my battery got completely drained (red led blinking) so i left it on the wallcharger for ~1day..
then at sometime it managed to boot up itself.. i left it for charging till 100%
after that i did a few "wipe battery stats" in xrecovery and now it seems to work stable again..
is it possible that messed up battery stats could cause the problem?
Wow, that would be nice.
A question! Was the little led on while charging? Because when I put my phone in the loader, it turns green (as if the battery is completely empty) and after a while it just goes off (when it would normally turn red). Do you have that to?
Putting my phone in the loader now, and waiting till tomorrow! Hope this helps!
yea, i've noticed this with my phone too..
strange led behavior..try to plug the charger first (green led turns on, cant say whether its charging or doing anything else) and then put in the battery and wait
maybe you're lucky and the phone will boot
and report pls
I didn't work. I've put my phone in the loader for over 24 hours, but nothing happened.
But my phone wasn't completely drained. Perhaps that is a condition to make this work. The only question is, how do I drain my battery when I can't turn on my phone?
i have used an 5watt light bulb ^^
connected on + and - and then waited till light goes out
Wel, I connected a little lamp and waited until it went out. Then when I put my battery in my phone and pressed the ON button nothing happend, not even the green light flashing shortly.
When I put my phone in the loader the LED started flashing red. And that whent on for a while until it stoped, and the LED did nothing. Then I waited over 24 hours, but nothing has happend.
When I put my phone in the loader now, it's just like before, the green light burns a little while, then nothing..
it happened to me again.. freeze and then no boot.
but i think i know whats wrong. for my phone i can say, that the battery is ok and the rom/os aswell.
its hardware problem. something is screwed up inside the phone.
when i press the phone at randomly places and hold it + then pushing on-button it boots up
i will open it tomorrow
Related
my x10 die suddenly, there was 94% battery left, not plugged out long, few hrs later notice phone was off,and it will not power on again, press power to try to turn it on all it does is vibrate and that's it.
tried to flash stock 2.1 back on but not sure if it did anything, took over night or flash tool to finish, still no boot after that, press power and it vibrates that's all, sometimes it doesn't even vibrate, battery is good, works fine in another x10, put a fully charge battery in it and same result.
anyone know what happened to it?
was running eternity 3a rooted with DT.
I'm going to have to send that in for warranty, hope they won't find anything on it and void the warranty.
Was the phone quite hot at the time or heating up when trying to boot?
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
sharathx10 said:
Remove the battery for a minute or so and try flashing with SEUS.... Check if battery is hot
Click to expand...
Click to collapse
That usually does the trick. Unplug battery for 1 minute, reinsert it and try again.
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
do you have a SD card inside. Might be a bad SD card try taking it out and booting it. Happened to me before.
blagus said:
That heating problem is present in X8 too... While tethering is enabled phone gets very hot and if you don't act phone will freeze...
Click to expand...
Click to collapse
Hi, just wanted to jump in and ask a few questions about this situation.
Do you always experience this issue? How long before it freezes? What "act" are you doing to prevent freezing? Does the phone work normally afterwards?
Hope you can help me out with some answers, I want to look into this.
instead of starting a new thread,i'll post here..
i have this restart problem..
Before this i try to fix my friend X10.. after many tries and a month acctually,i give up..
Now one more of my friend gave me another X10 which have the same problem..
Problem:
The phone will boot but after several minutes it will auto shut down and when i try to power up no vibrate and stuck at black screen.
when i pull the battery out and on again it vibrate and boot.just after boot animation it will shut down again..
Solution that i have tried so far:
Update with SEUS.
Send to profesional phone service to downgrade to 1.6.
Upgrade/flash with flash tool with GENERIC
Upgrade/flash with flash tool with X10_1.0_SE_StockRom_MultiTouch
Wipe user data in flash tool & x recovery
after several tries i got it work and i root and install x recovery.
Flash from xrecovery with custom rom Eternity.build003a.signed
format memory card.
Change battery.
All the solution i've tried doesn't make the problem dissappear.
anyone have ideas or solution?
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
If the battery has drained out, it might take some time before it kicks in and indicates that it is charging.
If the ROM has failed somehow, it might not show that it is charging at all, but might be charging.
Either way: Let it charge "blindly" for a while, and see what happens.
Once it does boot up to some level or shows life-signs, let it charge fully before you'l attempt a ROM flash.
The flash/recovery mode needs a full battery, and reason is that the external power isn't used even when connected while in flash/recovery mode.
If you happen to be in bad luck, and the ROM failed as a result of a drained battery, you might have to charge the battery externally. Use an external battery charger made for 3.6 volts Lithium Polymer batteries, and make sure to align the + and - terminals properly.
I can recommend the multicharger from Powerbase, called C-734U:
http://www.powerbasehk.com/product.php?id=148
Using it myself to charge the X10 battery, as well as other batteries from other devices I have.
EDIT:
(For some reason, powerbase has taken back that it'll charge Lipo batteries, but when I bought mine, it was described as a li-ion, li-poly and Ni-MH charger, and it't ability to charge li-poly batteries was the very one reason to why I bought it.
I suspect PowerBase does not want to take responsibility if anything happens to the li-poly-batteries, as they are known to be more dangerous than other types.)
I've left it on the wall charger all night, no response or anything. Luckily, I bought a new battery a few days ago, so when that comes in, hopefully it will be charged enough for this thing to boot.
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
laneyofdeath said:
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
Click to expand...
Click to collapse
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
king-iyokan said:
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Yeah, i'm not sure what he expected. But, good news! Now for some reason my phone started blinking red whenever I tried to turn it on! I guess the battery completely ran out or something. It also blinks every now and then when plugged in, so I guess it's charging. The previous owner of this phone said that it had some battery problems, so that's why I ordered that new battery. I'll let it charge for awhile and let you guys know what happens.
Okay, after getting my new battery, the phone will still not turn on. I think i've figured out two behaviors:
1. If the battery is nearly completely out of charge, it will flash a red light
2. If the battery has charge, it will not do anything at all.
Anyone know how to fix this?
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
ToledoJab said:
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
Click to expand...
Click to collapse
No vibration, the red LED flashes three times, and that is , as I said before, what happens when the battery seems to not have any charge. If I have a charged battery it does absolutely nothing.
Have you removed sim & sd card and tried. I know it sounds dumb but when I flashed a bad kernel I had to try to connect flash mode like 10 times. Finally I left the phone unplugged from pc, started flashtool and started flashing. I only put battery in phone just before holding back key. I never connected USB until tool said to dis-connect phone and connect in flashmode.
i wish you luck, I know how I felt when it went wrong
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
FireFreek said:
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
Click to expand...
Click to collapse
Try to flash any latest kernel via flashtool . Go for doomkernel . I think its software issue . Try this first .
Almost same here please help..
Last night battery ran out of charge & phone switched off.. then i plugged the charger it doesn't charge.. after some time i tried turning on.. Vibrates with the green LED but nothing happens then..
Note: This is not the 1st time i'm letting my phone drain, but facing this problem for the 1st time..
Rom : Spikelabs GB Gaming rom
Kernel : Ferakernel v23 beta6
I tried another battery, charger, data cable.. Tried flashing stock & spikelabs kernel., but of no use..
Any help is greatly appreciated..
Thanks in advance.. :good:
Something like that happened to me not long ago!
I was trying to flash some ROMs and I messed up then my phone wouldn't turn on!
But Miracously, I could flash a Stock 2.3.3 which fixed the problem!
At first, I used Sony PC Companion, which helped a lot- and after I screwed it for the second time, I used FlashTool-
I don't know if this was helpful, but I hope your x10 will be fixed soon!
yeah try the PC Companion first, it helped me too a couple of weeks ago
No luck...
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
ashok weird said:
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
Click to expand...
Click to collapse
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
sanababitz said:
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
Click to expand...
Click to collapse
Tried Ferakernel, Stock GB kernel, etc bro.. No luck..
Flashed Stock GB firmware more than 3 times still no luck :crying:
SEUS not working _ couldn't connect to network..
SUS does not have x10 enlisted
Went to 3 service shops at - Ritchie street, Chennai. They simply said harware issue (Short in board) and gave back the phone.
Now given at a better service centre. Will get back on monday it seems. Will update the status friends..
Thanks..
Here also they said the same reason friends.. Short in board..
Is there any way i could recover the phone???
Hey guys i've a problem with my x10
So one night i was playing with it than the other day the phone would start
so i thought yeah right might be the battery or something. i took it to my friends x10 it was with 87% charged so i exclude this
Than i tried to flash with flashtool a new kernel and i get stuck at 9% or 15% depending on the kernel i use.
With SEUS it starts to repair but it says. No new updates avaiable after a few moments.
Some information regarding my phone
Unlocked Bootloader
FXP KERNEL
MM TEAM MIUI V4
The phone vibrate but doesn't start or load the kernel.
What do i do?!
Srry for my bad english
Thx in advance
Usrle flashtool to reflash kernel or firmware.
already did but i get stuck at 9% or 15% flashing the kernel
I'm downloading a full generic rom x10a
having similar problem
Hi, I had similar problem as well
X10i running FXP CM7 suddenly just wont boot n charge after I turn off the phone
it wont boot after flashing anything (firm or kernel) except the official firm
now that I end up with a cap R bootloader but flashtool claim that bootloader is rooted
do I still keep the bootloader unlock?
i guess you have a locked bootloader since the original firmware is loading just fine even tho rooting has nothing to do with the bootloader it self. i'm only guessing.
I'm stuck at. Flashing Loader
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
[XBOCT]™ said:
I bricked my phone last week and it got stuck in a boot loop.
I downloaded the x10a generic Stock ROM and flashed it via Flashtool and it worked like a charm.
Hope this helps.
Click to expand...
Click to collapse
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
same problem repeat
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
mooving said:
Hi, just confirm that the bootloader remain unlock as long as the flashtool claim its ROOTED
had you try other than official 2.3.3 ftf?
because I just got the same unable to boot problem repeated again
this time cant get boot on even stock 2.3.3 firm
but I was able to boot up and charge on 2.1, then get root, recovery and kernel (w/o unlock bootloader again) and go straight to custom ROM with no problem
Click to expand...
Click to collapse
i'm using
X10a_2.1update1_r2.1.A.0.435_Generic.ftf
And it get stuck at Flashing loader
Idk but i can "read" the kernel when i dump the propriets but i can't "right" when i try to flash something
Anyone?
guys?
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
LJE said:
you said your phone is "bricked"
I'm not sure if you know what that means.
If you say you've bricked your phone then no one can help you.
A brick is a brick. It doesn't matter if it weighs a few kgs or a few hundred grams. A brick can't receive phone calls.
And your phone isn't even a normal brick... You wrote that it's "really bricked"
Are you building a house anytime soon?
Click to expand...
Click to collapse
maybe i'm wrong idk maybe is a soft brick. thats why i'm asking for some help.
almomdegal said:
But that way you weren't at a brick point.
You get brick when u get those 3 blink red LED and the phone doesn't do anything
By the fact that your phone were able to load the kernel. i guess
Click to expand...
Click to collapse
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Try wotanserver's flashtool...
http://www.wotanserver.com/en/
Good luck
SysGhost said:
The red led blinking rapidly three times means the battery is "out of juice".
I've said it earlier: Several X10 devices have reached an age, where battery failures are fairly common due to charge cycles and/or age. Specially if one got it just after the launch.
Anyhow, what you can do, is let the device charge "blindly" for a while, and a while I mean for half an hour to a few hours. Then it should, out of the blue, jump into "active" charging (With the battery screen showing offline charging)
If this doesn't happen you might have to charge the battery externally.
...or even replace the battery.
-"Why?", one might ask.
Reason is that the flash mode only works with a charged battery.
If it empty, it won't engage the flash mode at all. Stupid design, yes, but that is how it is.
Worst thing is, that the battery does deplete/discharge while in flashing mode. That is why it's so important it's fully charged and fully working, before one engages in flashing activities.
See this post for more information about this: http://forum.xda-developers.com/showthread.php?t=1642154
Click to expand...
Click to collapse
Didn't work, i even use my friends battery to flash it and it didn't work
almomdegal said:
Didn't work, i even use my friends battery to flash it and it didn't work
Click to expand...
Click to collapse
Well, if the battery issue was fixed, and you're sure the battery is fully charged, then try this: (Quoting from my other post)
I've charged/replaced the battery, and are having trouble with starting up. Earlier flash failed. Now what?
Don't worry. It's pretty darn hard to truly brick this device. Even if the screen remains black, there's still hope.
Once that the battery issue has been dealt with, you can move on:
Download the latest Flashtool and the proper global firmware (FTF-file) for your device from here:
http://forum.xda-developers.com/show...ight=flashtool
1: Extract/Install the Flashtool to a folder of your liking.
2: Copy the ftf-file to the "firmware" folder in the Flashtool folder you just created above.
3: Start Flashtool. Click the Bolt icon (flash). A Window appear. There, choose "flashmode". Cllick OK.
4: A new window appears. In the list on the left, choose the Generic firmware you downloaded and copied into the "firmware" folder. Should have a similar name as the file itself. (Or manually open the ftf-file from the "..." icon on the top right.)
5: Hit "OK. Follow the instructions you get on the screen:
1 - Unplug the device.
2 - Power off the device. (Unplug and replug the battery to be sure it really off, and not stuck in black screen)
3 - Press the "back" putton, and hold it down while performing the next task.
4 - Plug the device into the computers USB.
Click to expand...
Click to collapse
Forced flashing should now start.
Click to expand...
Click to collapse
time to accept the fact that it is really brick
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
mooving said:
Hi @almomdegal,
if you try flash using another full charge batt n its not work, I think this forum is no longer works for u anymore.
I own a faulty X10 as well, random shut down (no warning at all) then wont boot n charge
reflash it, revive for few days and dead again, and reflash....
now it is really dead, no problem appears and it show flash successful and it just wont boot or charge but vibrate non stop
I just send the phone to service center and the board need to be replace
so its time to send to the real professional to solve it, coz this problem ain't software downloaded from internet can solve anymore
Click to expand...
Click to collapse
yeah i guess so.
I just needed this closure i'll send it to service today
Hi guys/girls/undecideds,
My phone made me a sad panda recently when it stopped booting correctly - on startup it vibrates as it should, the screen lights up, but does nothing more - it does NOT reach the sony-ericsson logo that comes up, and the light goes off. It continues to repeat this loop about once every five or so seconds.
Obviously, not being a total moron (i'm only like, 40% moron), my first thought was to reflash the software, but I can't, because every time I connect the phone to flashtool, it disconnects a couple of seconds later and obviously, the flashing fails.
Can you help me find my smile?
sodslaw said:
Hi guys/girls/undecideds,
My phone made me a sad panda recently when it stopped booting correctly - on startup it vibrates as it should, the screen lights up, but does nothing more - it does NOT reach the sony-ericsson logo that comes up, and the light goes off. It continues to repeat this loop about once every five or so seconds.
Obviously, not being a total moron (i'm only like, 40% moron), my first thought was to reflash the software, but I can't, because every time I connect the phone to flashtool, it disconnects a couple of seconds later and obviously, the flashing fails.
Can you help me find my smile?
Click to expand...
Click to collapse
It's behind the cupboard on the second floor, you left it there last week
But on a more serious note, have you tried doing a repair using either SEUS or PC Companion? It flashes your phone all the way back to original firmware, but that's always better than nothing
Yes, i've since repaired the firmware and the problem persists.
If you start it up, does the led flash red?
Nothing from the LED. Only time I can see the LED is when it's on charge.
uhmmm... i guess Sony-Ericsson repair center would be an option at this point, wouldn't know what it could be.
Was this just random? Or any damange happend?.. Looks like some harware issue.. If u can find some video's on youtube make for disassmely n check if internal the connection are connected properly. Specially the flex which connects to the motherboard.
Sent from my U20i using xda premium
Yes, disassembled and reassembled the phone and checked all the internal connections, and everything seems fine as far as I can tell - I disconnected and then reconnected all the connections anyway just in case, and the problem persists.
Problem just started one day, but I was drunk at the time (surprise surprise) so it's not inconceivable that it MAY have taken some damage, but I'm very much certain it did not.
Ok can u tel which ROM n kernel u are on?? N after connecting ur phone into flash mode ( as u said in the main thread ) it disconnects, can u tell which error it reports from its log..
Sent from my U20i using xda premium
No idea which rom and kernel - what's on it currently will be the latest firmware that PC companion repairs with.
I can't tell which error it is, it just says "error: flashing aborted" in flashtool.
sodslaw said:
No idea which rom and kernel - what's on it currently will be the latest firmware that PC companion repairs with.
I can't tell which error it is, it just says "error: flashing aborted" in flashtool.
Click to expand...
Click to collapse
Once, I got the same problem as you... I solved it via SEUS... Seeing you said 'PC Companion', I suugest you to use SEUS (Sony Ericsson Update Service). Those are two different programs..
Hopefully, it helps..
And, by the way, what happened when you open flashtool, and connect your phone in flash mode ? Does it keep getting errors, or just when you tried to flash some kernel ?
Sent from my U20i using XDA
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
gonix said:
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Click to expand...
Click to collapse
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Screen-shots are from the old PC Companion, byt they still looks very much like them in the new version
http://forum.xda-developers.com/showpost.php?p=17458289&postcount=8
Emperor.dk said:
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
Click to expand...
Click to collapse
Oh I know someone who has the same x10 with me. I guess Ill have to try your suggestion.
SmG67 said:
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Click to expand...
Click to collapse
It doesnt help because when Im in the part where it says, press the back button while inserting the usb, the phone cannot be detected and so the update cannot continue.