Related
I bricked my X10 (so-01b) and got Yellow exclamation mark after I tried to debrand it by SEUS.
After that, I tried almost all the methods posted on the website.
1. Using the X10flash tools including unbricked method and root method(first step).
It seems flash is working, however the flash procedure last only around 3 minutes not 5 minutes as most people mentioned. It also ended up with a "test" which means the flashing is completed without any error.
However, after removing the cable, rebooting the phone, Yellow exclamation mark is still there.
2. Method of replacing the Java file into the plugins folder and adding x10a~~ files into the folder of the Update Service of the SESU, also deleting the db folder before flashing.
Restore/repair by SEUS, downloading and flashing was running smoothly and ended up with flashing successfully.
However, after removing the cable, rebooting the phone, Yellow exclamation mark is still there.
3. Deleted the SEUS , re-installed, and changed another brand new cable.Tried the method 2 mentioned above.
However, the result is the same. Failed.
4. Using Omnious. Flashing end up with "Failed" and an error code returned, which you can take a look as following. Result is the same as above three.after removing the cable, rebooting the phone, Yellow exclamation mark is still there.
Code:
Action journal
22:29:08 Flash
22:29:08 Allows to change languages supported by the phone and upgrade its firmware.
22:29:08 Operating system: Microsoft Windows XP Professional Service Pack 3 (build 2600)
22:29:08 Application version: 0.07.2279 (beta)
22:29:08 . The action name is 'Flash'
22:29:08 Selected phone type: Xperia™ X10
22:29:08 i Instructions
22:29:08 i 1. Make sure the phone battery is charged to at least 50%.
22:29:08 i 2. Switch off the phone!
22:29:08 i 3. Remove the phone battery and wait at least 5 seconds before reinserting it!
22:29:08 i 4. Press and hold the return back button, then connect the cable to the phone!
22:29:08 . The action started waiting for the user
22:29:25 . The action finished waiting for the user
22:29:25 Connecting via SEMC USB Flash Device (USB3)...
22:29:25 Device driver version: 2.2.0.5
22:29:25 Detected chipset: QSD8250
22:29:25 Boot mode: EROM
22:29:25 IMEI: [email protected]@@
22:29:25 Sending loader...
22:29:26 Establishing connection to the server...
22:29:29 Receiving news...
22:29:34 i No news
22:29:34 Actual credit: 0.00
22:29:40 Writing file phone.zip...
22:30:18 Writing file X10i_GENERIC_1234_8465R8A_R1FB001.zip...
22:33:38 e Failed!
22:33:38 . The action entered shutdown phase
22:33:38 . The action reported failure
Error code
# E39CDD9F86C3082E
Error details
---
61 C6 C0 A4 65 CB CD 00 FF 08 E1 72 F3 9F B5 AE
13 9B E7 8D E5 86 63 FA 78 BD E4 7E ED 5F 85 68
09 52 D0 4B 3E 18 6D E0 61 94 3A D6 3F 7D 06 ED
11 DB BB C5 11 03 FE 12 A2 17 E5 DB 4F B0 1E 0D
C5 5C E6 DF 47 8B A0 93 02 E4 6C 19 80 4D 59 91
46 C1 3B 15 F6 69 01 6B CA 64 A3 13 2E 26 7A 7C
7E AD 9A 9E 1D EB 00 E8 80 F0 7A 96 0F 25 D0 BA
D5 FD 93 6D 4B 5B 30 D9 6C D7 4D 92 B4 C0 04 64
F7 56 66 50 2A AA 3B E5 F3 13 07 8D EE A3 41 61
48 50 E9 72 04 6F 71 F5 55 D4 0A 0C 6D 2F 05 E8
77 58 E8 34 2A 17 BD A1 E1 9A FF 0A ED 48 D5 09
C7 38 25 15 95 C7 43 B0 6F 20 0C E7 BD 5C 0B 29
17 8E 39 EE F3 F9 7F 69 EF 5B A1 DC B3 74 21 FF
19 DE A7 ED 25 46 5D DE 0F B6 8F 34 FD F2 BB 58
E7 3F D9 C4 D5 24 2D E1 A1 DA BF 44 5B 79 BB 34
F9 22 57 42 85 66 03 14 99 C1 7C 7F
---
I can show you my hardware infomation identified by Omnious.
Code:
Action journal
23:48:43 Identify
23:48:43 Shows detailed information about the connected phone.
23:48:43 Operating system: Microsoft Windows XP Professional Service Pack 3 (build 2600)
23:48:43 Application version: 0.07.2279 (beta)
23:48:43 . The action name is 'Identification'
23:48:43 Selected phone type: Xperia™ X10
23:48:43 Selected connection method: USB EROM
23:48:43 i Instructions
23:48:43 i 1. Make sure the phone battery is charged to at least 50%.
23:48:43 i 2. Switch off the phone!
23:48:43 i 3. Remove the phone battery and wait at least 5 seconds before reinserting it!
23:48:43 i 4. Press and hold the return back button, then connect the cable to the phone!
23:48:43 . The action started waiting for the user
23:48:50 . The action finished waiting for the user
23:48:50 Connecting via SEMC USB Flash Device (USB3)...
23:48:50 Device driver version: 2.2.0.5
23:48:50 Detected chipset: QSD8250
23:48:50 Boot mode: EROM
23:48:50 EROM version: 1226-2253 R8A013
23:48:50 IMEI: [email protected]@@
23:48:50 Device ID: 7E2914576285FCBDDB99FD73DE3CC610FDEF4539
23:48:50 Minimum loader AID: 0001
23:48:50 Minimum software AID: 0001
23:48:50 Minimum EROM AID: 0001
23:48:50 Minimum customization AID: 0001
23:48:50 Minimum simlock AID: 0001
23:48:50 Serial number: CB511JJNU6
23:48:50 Color: Red SEMC
23:48:50 Simlock state:
23:48:50 Phone model (from TA): SO-01B
23:48:50 Current CXC (from TA): 1227-4612_R1EA018
23:48:50 Current CDA (from TA): 1233-7397_R16A
23:48:50 Current FS (from TA): 1227-4607_R1EA018
23:48:50 Sending loader...
23:48:51 Waiting for loader response...
23:48:52 Flash chip ID: 002C-00B3
23:48:52 Turning off the phone...
23:48:54 i Please disconnect battery and cable from the phone!
23:48:54 s Successfully done.
23:48:54 . The action entered shutdown phase
23:48:54 . The action reported success
Additional details
---
2C B5 7E 53 CE E0 A6 3F 3C 23 1E 6B 18 79 5E 29
34 FB 48 D0 90 2F EA 9F 2C DC 52 9B F8 29 3A 1E
72 19 76 4D 80 8F 86 61 E4 89 80 CF 76 E9
---
I feel really sad and frustrated, seems most of the guys here can solve the Yellow exclamation mark issue with one of the 4 methods I have tried. I really need your help!
Thanks a million in advance!
I had this yesterday, just connect now phone to seus and repair it. It helped and now everything is working
Sent from my X10i using XDA App
maxld said:
I had this yesterday, just connect now phone to seus and repair it. It helped and now everything is working
Sent from my X10i using XDA App
Click to expand...
Click to collapse
Tried at the very beginning, but failed......
Strange, does it connect in bootloader mode?
Sent from my X10i using XDA App
maxld said:
Strange, does it connect in bootloader mode?
Sent from my X10i using XDA App
Click to expand...
Click to collapse
Sure, every methods require the x10 connected in flash mode.
Remove battery, wait 15 minutes. Put battery in but don't turn on, just enter straight into bootloader mode when you need to.
Clear out content in SEUS folder and start over again.
Good luck!
So is your phone originally the SO-01B (docomo)? If so, then you should either be using SO-01B files or X10i (NOT X10a).
Can you try reflashing to SO-01B firmware to make sure that there isn't anything wrong with your phone? Just run step1 from the following (this is the original root package, which used docomo firmware). Don't run any other steps.
ROOT_F2v1.rar (borrowed from [GUIDE] Root your X10 R2BA023 !)
For the SEUS method, why did you replace the java files? That's only for decrypting ROMs, not for flashing your phone. Also, you should be using X10i files.
For the Omnius method, did you put the files in the correct order? Application should be X10i_GENERIC_1234_8465R8A_R1FB001.zip (large file, ~100MB) and Customization should be phone.zip (small file, ~15MB). Since you have the SO-01B, you could also try these files:
SO-R1EA025-DEK.rar (borrowed from Decrypted x10 roms - latest r2ba024 rom - with sin reconstructor)
mtechfan said:
Remove battery, wait 15 minutes. Put battery in but don't turn on, just enter straight into bootloader mode when you need to.
Clear out content in SEUS folder and start over again.
Good luck!
Click to expand...
Click to collapse
Hi, Dear friend, Thanks a million for your suggestion. I will take a trial and report the results tonight since it is already 4 am, I am live in Japan.
I already have the same problem and resolve it with SEUS.
Try to change USB port if you have an issue.
Grospolina said:
So is your phone originally the SO-01B (docomo)? If so, then you should either be using SO-01B files or X10i (NOT X10a).
Can you try reflashing to SO-01B firmware to make sure that there isn't anything wrong with your phone? Just run step1 from the following (this is the original root package, which used docomo firmware). Don't run any other steps.
ROOT_F2v1.rar (borrowed from [GUIDE] Root your X10 R2BA023 !)
For the SEUS method, why did you replace the java files? That's only for decrypting ROMs, not for flashing your phone. Also, you should be using X10i files.
For the Omnius method, did you put the files in the correct order? Application should be X10i_GENERIC_1234_8465R8A_R1FB001.zip (large file, ~100MB) and Customization should be phone.zip (small file, ~15MB). Since you have the SO-01B, you could also try these files:
SO-R1EA025-DEK.rar (borrowed from Decrypted x10 roms - latest r2ba024 rom - with sin reconstructor)
Click to expand...
Click to collapse
Hi, Dear friend, Thanks a million for your suggestions. My handset is originally the SO-01B (docomo). I have runned step1 from original root package with docomo firmware you suggested at the very beginning. However, I failed. I am supprised it only took 3 minutes to complete the flashing for the first step which normally take 5 minutes regarding the others comments. Although the cmd windows shows it completes with ~test in the end without any error, I am afraid it actually missd flashing some files. As for the second suggestion on SEUS method, I will take a trial and report here later. As for the third suggestion on Omnious, I thout I have made a mistake with the oder placing the two files. I have just re-flashed my X10 by Omnious tools according to your suggestion, which the application is with X10i_GENERIC_1234_8465R8A_R1FB001.zip (large file, ~100MB) and Customization is with phone.zip (small file, ~15MB), however I still got a failed results during the application file flashing.(the customization file flashing has not even started ). You may take a look at following log infomation.
Code:
Action journal
02:46:27 Flash
02:46:27 Allows to change languages supported by the phone and upgrade its firmware.
02:46:27 Operating system: Microsoft Windows XP Professional Service Pack 3 (build 2600)
02:46:27 Application version: 0.07.2279 (beta)
02:46:27 . The action name is 'Flash'
02:46:27 Selected phone type: Xperia™ X10
02:46:27 i Instructions
02:46:27 i 1. Make sure the phone battery is charged to at least 50%.
02:46:27 i 2. Switch off the phone!
02:46:27 i 3. Remove the phone battery and wait at least 5 seconds before reinserting it!
02:46:27 i 4. Press and hold the return back button, then connect the cable to the phone!
02:46:27 . The action started waiting for the user
02:47:10 . The action finished waiting for the user
02:47:10 Connecting via SEMC USB Flash Device (USB4)...
02:47:10 Device driver version: 2.2.0.5
02:47:10 Detected chipset: QSD8250
02:47:10 Boot mode: EROM
02:47:10 IMEI: [email protected]@@
02:47:10 Sending loader...
02:47:15 Establishing connection to the server...
02:47:19 Receiving news...
02:47:22 i No news
02:47:22 Actual credit: 0.00
02:47:30 Writing file X10i_GENERIC_1234_8465R8A_R1FB001.zip...
02:50:33 e Failed!
02:50:33 . The action entered shutdown phase
02:50:33 . The action reported failure
Error code
# E39CDD9F86C3082E
Error details
---
4B B3 B7 81 D4 A0 1C 73 C2 C5 F8 25 C2 05 14 45
22 C8 3E 2E F6 CF F4 37 F9 CC B3 85 FC 8A 04 EB
6A 93 97 D6 31 F3 FC 13 5E A7 6D 6B B0 C8 5F 7E
8C 06 02 D8 7E 88 D1 41 5F E4 82 A6 DC 1B 27 CE
18 DF 1F FC F6 E0 77 1E 43 57 F5 22 4F 46 86 82
19 E0 9C 4E E5 DC EE C6 4B 17 FA 16 C1 8D 85 81
9F 90 1D 7D 92 00 EF 1B 3D 43 DD AB 00 6C F1 29
C8 5C B4 F6 D8 AE E1 14 6D D8 5A EF DB E9 3D A7
D6 57 61 8B 9B 3F EA 68 CC DC 1E CE 21 D6 E0 72
E9 F3 30 29 17 26 E0 26 2A A7 53 09 80 06 84 95
16 99 51 A9 25 02 D2 AC DE 55 58 B7 9E 15 74 77
5A E2 15 9C F8 4E 94 E3 6E D1 65 9A 2C 09 32 EA
CA 0D 40 CB 42 6E AE 64 50 14 C8 E7 7E 83 F8 E2
44 FD FE 4E 36 F1 B4 73 8E C5 D8 C9 12 59 BC AB
F8 FE 60 DF A6 31 C4 2C 1E 6B E8 79 56 30 9A A9
E6 7D 70 DF EA 91 D4 D9 9A CE 65 04
---
Flashing with DoCOMO SO-R1EA025-DEK, Failed too.
Code:
Action journal
03:11:20 Flash
03:11:20 Allows to change languages supported by the phone and upgrade its firmware.
03:11:20 Operating system: Microsoft Windows XP Professional Service Pack 3 (build 2600)
03:11:20 Application version: 0.07.2279 (beta)
03:11:20 . The action name is 'Flash'
03:11:20 Selected phone type: Xperia™ X10
03:11:20 i Instructions
03:11:20 i 1. Make sure the phone battery is charged to at least 50%.
03:11:20 i 2. Switch off the phone!
03:11:20 i 3. Remove the phone battery and wait at least 5 seconds before reinserting it!
03:11:20 i 4. Press and hold the return back button, then connect the cable to the phone!
03:11:20 . The action started waiting for the user
03:11:35 . The action finished waiting for the user
03:11:35 Connecting via SEMC USB Flash Device (USB4)...
03:11:35 Device driver version: 2.2.0.5
03:11:35 Detected chipset: QSD8250
03:11:35 Boot mode: EROM
03:11:35 IMEI: [email protected]@@
03:11:35 Sending loader...
03:11:40 Establishing connection to the server...
03:11:43 Receiving news...
03:11:45 i No news
03:11:46 Actual credit: 0.00
03:11:54 Writing file FILE_277398338_1275040924000_1274947104000_277398125_112659344_INFILE_LONGTERM.zip...
03:14:56 e Failed!
03:14:56 . The action entered shutdown phase
03:14:56 . The action reported failure
Error code
# E39CDD9F86C3082E
Error details
---
6F CF 37 25 E8 9C D0 F1 4A 7F 34 00 0E B5 A8 80
E4 4C 92 CA 2A 2D E0 AB ED 76 EF 5F 30 F8 98 07
22 29 7B B2 CD F1 10 AF 96 63 E9 0F 7C 44 DB 12
18 C2 F6 82 A2 6A 3D 23 4B 5E D6 42 10 69 B3 1C
EC 1B CB 58 36 22 A3 E2 4B 6D 39 F8 03 CA 3A AE
71 5A C8 D4 45 3E C2 A4 5F 2D 2E CC 8D 01 E9 ED
2B 54 B1 99 EE 7C 63 59 F5 07 D1 B1 4C E0 0D 3B
A0 E6 D8 AC 84 B2 0D 88 85 E2 7E 75 97 65 A9 75
5E 13 35 D1 5B 03 26 EA 44 66 2A EA ED 5A AC A0
7D C9 9C 33 CB 3A 0C 44 3E E3 07 2D B0 74 E8 79
5E DD 45 33 D9 FE 3E 10 16 91 2C D3 AE 66 08 27
32 3F AB 7B 24 52 80 81 86 6B C1 7E 1C 85 A6 C6
C2 37 14 6F 7E 52 62 98 58 2E F4 C3 32 0F 4C CE
2C 47 52 2A 6A 13 A0 EF 66 FF 04 ED 5E D5 28 C7
4C C4 F4 3B 26 B3 B0 90 D6 2F EC 63 E6 42 66 45
72 C7 E4 7B B6 73 C0 BB 8E F4 B1 60
---
I will report more results later since it is already 4 am in Japan. I have to go to bed.
Thank you again for your big help.
Battosai94 said:
I already have the same problem and resolve it with SEUS.
Try to change USB port if you have an issue.
Click to expand...
Click to collapse
Hi friend, thank you four suggestion. i will take a trial and report here later.
when flashing with x10flash deal, step one of root, you have to wait till it says press any key to continue, or you have only flashed a portion of the full rom, it will read like it's done several times throughout the process
mtechfan said:
Remove battery, wait 15 minutes. Put battery in but don't turn on, just enter straight into bootloader mode when you need to.
Clear out content in SEUS folder and start over again.
Good luck!
Click to expand...
Click to collapse
Unfortunately, I do the process according to your suggestion, but the result is the same as before.
dan-htc-touch said:
when flashing with x10flash deal, step one of root, you have to wait till it says press any key to continue, or you have only flashed a portion of the full rom, it will read like it's done several times throughout the process
Click to expand...
Click to collapse
Yes, I did exactly what the "howto" file told us to do, but failed. The flashing time is only 3 minutes.
Battosai94 said:
I already have the same problem and resolve it with SEUS.
Try to change USB port if you have an issue.
Click to expand...
Click to collapse
I have even tried with every usb ports on my PC and even tried with a different PC.
lazy i hope that you have more luck than me, my X10 was dead and send to SE to repair, you can see my history
http://forum.xda-developers.com/showthread.php?t=714538
alucine said:
lazy i hope that you have more luck than me, my X10 was dead and send to SE to repair, you can see my history
http://forum.xda-developers.com/showthread.php?t=714538
Click to expand...
Click to collapse
Hi alucine, thank you for your reply.
OMG! I have exactly the same situation as your experienced.
If it is a nand failure issue, is that mean I should give up and send my phone to SE center rather than do any trial.
However, I am wondering most of the guy who came across the Yellow exclamation mark after updating by SEUS finally saves back their phones by using one of the methods. How can Bin4ry expected our issue is related to the NAND failure issue. How can we confirm whether we have the NAND failure issue or not after we got the Yellow exclamation mark. Is it exactly related to the battery condition when flashing the x10 with any method?
Can we draw the concultion that, the X10 user will got NAND failure(HW related) if the flashing was under poor battery condition.
Hi,
please be so kind and upload the log of the X10flash program. Because i personally dont know the Omnius Program
Like you said the falsher finishes the progress, if its 3 minutes or 5 minutes , i dont know I never measured the time of the process
If you upload the flashlog maybe we can help you.
The problem is following:
Maybe you have a bad nand, then X10flash, Omnius, SEUS or whatever try to flash your phone, all data is send correctly but the phone doenst write it to nand correct.
So what happens now after flash ? The bootloader checks and validates the firmware which is on your phone, if the calculated checksum is not correct the bootloader sends you to semc recovery (you see the triangle and the exclamation mark ! )
If nothing helps and X10flash runs correctly etc. then the last option is that your nand is ****ed up (this happens sometimes , you can compare it to faulty ram on PC or smth.). This is not too bad for you because SE has to exchange your device into a new one.
But first of all, please upload your X10 flashlog, and lets see what happens there
Regards
Bin4ry
Hi Bin4ry, thanks a million for your reply. I just re-flashed the x10 according to the first step in your tutorial. (http://forum.xda-developers.com/showthread.php?t=711907)
I attached the log code in my cmd windows. Pls take a look. seems there are three error info. in the end of the log files. I belive you understand well what is that mean. BTW, I still got triangle mark after this flashing. Thank you in advance for your great help. I also appreciate your great work for us in XDA forum.
Code:
2010-7-20 19:10:15 X10flash main
信息: start
2010-7-20 19:10:15 X10flash readReply
信息: <<< cmd=1,flags=1,length=46
2010-7-20 19:10:15 X10flash testPluged
信息: <<<VER="R8A013";DATE="20100119";TIME="17:24:00";
2010-7-20 19:10:15 X10flash writeCmd
信息: write(cmd=1) (finish)
2010-7-20 19:10:15 X10flash readReply
信息: <<< cmd=1,flags=1,length=586
2010-7-20 19:10:15 X10flash testCmd01
信息: <<<PROT_VER="01";DATE="20100119";TIME="17:24:00";VER="R8A013";UNIQUE_DEV_ID="7E2914576285FCBDDB99FD73DE3CC610FDEF4539";CXC="1226-2253";TYPE="S1_EROM";SEC_LOCK_STATUS="LOCKED";HASH_PUB_KEY="00000000000000000000000000000000";EROM_AID="0001";LOADER_AID="0001";SW_AID="0001";CUST_AID="0001";SIM_LOCK_AID="0001";IMEI="35949603234196";MSN="CB511JJNU6";SIN_VER="0001";SIMLOCK_TAMP="";AID_TAMP="NOT_TAMPERED";LOADER_ROOT="S1_Loader_Root_f851";EROM_ROOT="S1_EROM_Root_b15e";SW_ROOT="S1_SW_Root_ac12";CUST_ROOT="S1_Cust_Root_5789";SIM_LOCK_ROOT="S1_SL_Root_f20d";HW_CONF_ROOT="S1_HWConf_Root_ee5d";
2010-7-20 19:10:15 X10flash writeCmd
信息: write(cmd=9) (finish)
2010-7-20 19:10:15 X10flash readReply
信息: <<< cmd=9,flags=1,length=0
2010-7-20 19:10:15 X10flash writeCmd
信息: write(cmd=10) (finish)
2010-7-20 19:10:15 X10flash readReply
信息: <<< cmd=10,flags=1,length=0
2010-7-20 19:10:15 X10flash writeCmd
信息: write(cmd=5) (finish)
2010-7-20 19:10:15 X10flash readReply
信息: <<< cmd=5,flags=1,length=0
2010-7-20 19:10:15 X10flash writeCmd2
....................................................
....................................................
....................................................
The content is the similar, so I delete large amount of log info. here,
....................................................
....................................................
....................................................
2010-7-20 19:12:29 X10flash readReply
信息: <<< cmd=6,flags=1,length=0
2010-7-20 19:12:29 X10flash writeCmd
信息: write(cmd=6) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=6,flags=0,length=0
2010-7-20 19:13:18 X10flash writeCmd
信息: write(cmd=5) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=5,flags=0,length=0
2010-7-20 19:13:18 X10flash writeCmd
信息: write(cmd=7) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=7,flags=1,length=93
2010-7-20 19:13:18 X10flash testCmd07
信息: <<<ERR_SEVERITY="MAJOR";ERR_CLASS="PROTOCOL_CLASS";ERR_STATIC="UNVALID_COMMAND";ERR_DYNAMIC="";
2010-7-20 19:13:18 X10flash writeCmd
信息: write(cmd=6) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=6,flags=0,length=0
2010-7-20 19:13:18 X10flash writeCmd
信息: write(cmd=7) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=7,flags=1,length=93
2010-7-20 19:13:18 X10flash testCmd07
信息: <<<ERR_SEVERITY="MAJOR";ERR_CLASS="PROTOCOL_CLASS";ERR_STATIC="UNVALID_COMMAND";ERR_DYNAMIC="";
2010-7-20 19:13:18 X10flash writeCmd
信息: write(cmd=13) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=13,flags=0,length=0
2010-7-20 19:13:18 X10flash writeCmd
信息: write(cmd=7) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=7,flags=1,length=93
2010-7-20 19:13:18 X10flash testCmd07
信息: <<<ERR_SEVERITY="MAJOR";ERR_CLASS="PROTOCOL_CLASS";ERR_STATIC="UNVALID_COMMAND";ERR_DYNAMIC="";
2010-7-20 19:13:18 X10flash writeCmd
信息: write(cmd=10) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=10,flags=0,length=0
2010-7-20 19:13:18 X10flash writeCmd
信息: write(cmd=4) (finish)
2010-7-20 19:13:18 X10flash readReply
信息: <<< cmd=4,flags=1,length=0
2010-7-20 19:13:18 X10flash run
信息: ###test end.
Hi, i've got the same case on my phone!
So what we should do?
Hi guys, think i've bricked up my x10
after SEUS update the phone wont boot.. it vibrates on power but then stays black.
tried to reflash using the SEUS..
SEUS "recognizes" the phone (says "firmware already installed blabla.. reflash?) but at the flash progress it hangs at the beginning and finally aborts with an error message.
any ideas?
This might work.
tried the flashtool too.. no success
log:
28/041/2011 21:41:26 - ERROR - Please plug you device in flash mode
28/041/2011 21:41:27 - INFO - Searching Xperia....
28/041/2011 21:41:27 - INFO - Found at USB\VID_0FCE&PID_ADDE\5&284A1E07&0&5
28/041/2011 21:41:27 - INFO - Start Flashing
28/041/2011 21:41:27 - INFO - VER="R8A013";DATE="20100119";TIME="17:24:00";
28/041/2011 21:41:27 - INFO - Flashing loader
28/042/2011 21:42:33 - INFO -
28/046/2011 21:46:55 - INFO - Flashing kernel.sin
28/048/2011 21:48:10 - ERROR - Error flashing. Aborted
28/048/2011 21:48:10 - INFO - Now unplug the device and power it on
28/048/2011 21:48:10 - INFO - Then go to application settings
28/048/2011 21:48:10 - INFO - turn on Unknown Sources and Debugging
just tried the omnious for se v0.20 flasher.. same result
log:
Action journal
22:30:16 Flash
22:30:16 Allows to change languages supported by the phone and upgrade its firmware.
22:30:16 Operating system: Microsoft Windows XP Professional Service Pack 2 (build 2600)
22:30:16 Application version: 0.20.3728 (beta)
22:30:16 . The action name is 'Flash'
22:30:16 Selected phone type: Xperia™ X10
22:30:16 i Instructions
22:30:16 i 1. Make sure the phone battery is charged to at least 50%.
22:30:16 i 2. Switch off the phone!
22:30:16 i 3. Remove the phone battery and wait at least 5 seconds before reinserting it!
22:30:16 i 4. Press and hold the return back button, then connect the cable to the phone!
22:30:16 . The action started waiting for the user
22:30:31 . The action finished waiting for the user
22:30:31 Connecting via SEMC USB Flash Device (USB1)...
22:30:31 Device driver version: 2.2.0.5
22:30:31 Detected chipset: QSD8250
22:30:31 Boot mode: EROM
22:30:31 IMEI: 35941903911402
22:30:31 Sending loader...
22:40:18 e Failed!
22:40:18 . The action entered shutdown phase
22:40:18 . The action reported failure
Error code
# FEF0FA7628628BE2
Error details
---
6E 4B 0E AC 0D 8F E5 78 57 5C C8 E9 35 0A CD 05
FF EE E1 9C 03 D2 1B 5F 59 BE 49 60 E2 A1 63 F7
B1 6A E1 B5 BD 4E 7B 96 F7 C6 E7 54 95 F8 E5 8B
31 07 7F 7C 6D 28 21 90 98 0F 47 6D BB A6 C3 3A
F1 30 F6 46 4D 8F DB 48 69 F8 0D 96 71 9E A3 21
C1 3A DF AE 9B 52 4C 2D 49 63 89 AC 5B CC 90 25
D5 23 5F E0 83 72 C5 26 C9 EE 59 B8 63 FD C0 73
---
Flash stock 1.6 rom with flash tools and all will be good
Sent from my HD2 using XDA App
another problem occurs.. its seems, that the battery wont be charged anymore.
i wanted to try the 1.6 stock but i cant "boot" up in the flashmode.
i press the "back"-button then plugin the usbchord but no green led..insted the red led blinks up every ~2sec for a short period.
blmn1337 said:
another problem occurs.. its seems, that the battery wont be charged anymore.
i wanted to try the 1.6 stock but i cant "boot" up in the flashmode.
i press the "back"-button then plugin the usbchord but no green led..insted the red led blinks up every ~2sec for a short period.
Click to expand...
Click to collapse
Red LED means that battery is drained, should wait and charge battery without booting and you should be fine. If it still doesn't charge then buy a new battery.
it's working again
i think it was a battery charging problem.
plugged in for charging in the morning and when i got home, the system was booted up and the battery fully charged.
now everything is normal again.
thx for support, mates
i found out, that the battery is charged normally.
the problem happened again.
when holding power on it vibrates and nothing else.. black screen, no bootup logo, no background-light
halp pls
Did you sort this I had the same problem
sent with a geordie kiss using wb 2.3.3
1.download the global 2.1 stock flashable file
2.put it inside your firmware folder in flash tool folder
3.dont connect ur phone
4.hit flash and select the global firmware and wait till the flash tool ask u to connect ur phone
5.now remove ur phone battery
6.connect usb cable into ur phone with the battery is removed and now press and hold the back button on ur phone and insert the battery
I had the same problem and I fixed it using the above procedure.
All the best buddy...
runaway_bunny said:
1.download the global 2.1 stock flashable file
2.put it inside your firmware folder in flash tool folder
3.dont connect ur phone
4.hit flash and select the global firmware and wait till the flash tool ask u to connect ur phone
5.now remove ur phone battery
6.connect usb cable into ur phone with the battery is removed and now press and hold the back button on ur phone and insert the battery
I had the same problem and I fixed it using the above procedure.
All the best buddy...
Click to expand...
Click to collapse
i've tried but doesn't work for me.. not able to flash anything
still have the problem
Hi is there a way I can bypass the "emergency call" screen for xperia x10? The phone was bricked after unsuccessful upgrade to 2.3.3. I was able to load 1.6 back (using flash tool and forum instructions), but now phone is stuck in Emergency Call Only screen. SEUS is not helping either, always getting the message that the SW is up to date ( however, still running 1.6). Attempted to flash with 2.1 and suggested baseband combo with no luck, x10 just wont boots at all. With 2.3.3 it goes in to constant bootloops.
The other weird thing is, is when I push the Emergency Call button and the dial pad pops up I can press and hold the back button and instantly I can get a glimpse of my actual menu but in that same second it flips back to the emergency call only page??? Super frustrating so please any and all advice would be greatly appreciated.
Me first....wrong section...
PS in SEUS (Or PCCompanion) allthough it says up to date, you can still hit update anyway and it will fix it
brutus* said:
Hi is there a way I can bypass the "emergency call" screen for xperia x10? The phone was bricked after unsuccessful upgrade to 2.3.3. I was able to load 1.6 back (using flash tool and forum instructions), but now phone is stuck in Emergency Call Only screen. SEUS is not helping either, always getting the message that the SW is up to date ( however, still running 1.6). Attempted to flash with 2.1 and suggested baseband combo with no luck, x10 just wont boots at all. With 2.3.3 it goes in to constant bootloops.
The other weird thing is, is when I push the Emergency Call button and the dial pad pops up I can press and hold the back button and instantly I can get a glimpse of my actual menu but in that same second it flips back to the emergency call only page??? Super frustrating so please any and all advice would be greatly appreciated.
Click to expand...
Click to collapse
standalone SEUS comes up with following message (see attached) there is no option available to hit update .One more thing from X10 service menu the SIMLOCK status is unknown....
I"ve attached service menu screenshots for your reference
Pick a firmware you want, 2.3.3 se ect, pull the battery on the phone, use FLASHtool, set up ur ftf files, start flashtool, connect usb to phone, put battery back in while holding back key down, flashing should begin.
P.S... MAKE SURE YOU HAVE FULL FIRMWARE FTF WITH KERNEL...
Best regards,
Chris
OK,
Before you try the method above this post try getting back to stock...
So, make sure you update SEUS (Uninstall and reinstall from SE site) and try again.
If that does not work, try the same thing with PCCompanion.
Thanks Chris,
It goes in to constant boot_loops with 2.3.3 and 2.1.71 baseband
---------- Post added at 12:07 PM ---------- Previous post was at 12:06 PM ----------
Thanks gregbradley,
Already tried with few PC's, still no luck
brutus* said:
Thanks Chris,
It goes in to constant boot_loops with 2.3.3 and 2.1.71 baseband
---------- Post added at 12:07 PM ---------- Previous post was at 12:06 PM ----------
Thanks gregbradley,
Already tried with few PC's, still no luck
Click to expand...
Click to collapse
Hmmm...Can you tell me what baseband you are on and kernel
EDIT: and lets move this to PM's only please.
I wont help further in this thread...please PM me
This is the wrong section....check your PM's or start it again in the Q&A section
Flash 2.1 x10 A firmware... ur phone mst be simlockd ... so first unlock ur simlockd phone after upgrading to 2.1 n then unlock ur bootloader... then upgrade it to 2.3
Sent from my X10i using XDA Premium App
phone is stuck in Emergency Call Only screen and I cant check the kernel rev. enable "USB debugging" and etc. Please have a look at attached service menu screen shots
---------- Post added at 12:24 PM ---------- Previous post was at 12:18 PM ----------
Thanks varshil,
I've used almost every avalable 2.1 with forum suggested base-bans - still no success, its not even posting SE logo. Can load almost every available 1.6 firmware but stuck in "Emergency Call Only" screen
Please don't replay to this threat its in wrong secton!!
@op post it in Q/A section!!
questionmarks at simlock info indicates damaged security zone.
please download omnius and perform identification.
Sent from my R800i using XDA App
Folks how to move this Thread to appropriate section? Please advice
brutus* said:
Folks how to move this Thread to appropriate section? Please advice
Click to expand...
Click to collapse
Contact a MOD like pilot
what do you mean? I'm new to this forum, can you help?
---------- Post added at 01:48 PM ---------- Previous post was at 01:33 PM ----------
ID dump from omnius
Code:
Action journal
13:39:41 Identify
13:39:41 Shows detailed information about the connected phone.
13:39:41 Operating system: Microsoft Windows XP Professional Service Pack 2 (build 2600)
13:39:41 Application version: 0.23.3995
13:39:41 . The action name is 'Identification'
13:39:41 Selected phone type: Xperia™ X10
13:39:41 Selected connection method: USB EROM
13:39:41 i Instructions
13:39:41 i 1. Make sure the phone battery is charged to at least 50%.
13:39:41 i 2. Switch off the phone!
13:39:41 i 3. Remove the phone battery and wait at least 5 seconds before reinserting it!
13:39:41 i 4. Press and hold the return back button, then connect the cable to the phone!
13:39:41 . The action started waiting for the user
13:44:26 . The action finished waiting for the user
13:44:26 Connecting via SEMC USB Flash Device (USB2)...
13:44:26 Device driver version: 2.2.0.5
13:44:26 Detected chipset: QSD8250
13:44:26 Boot mode: EROM
13:44:26 EROM version: 1226-2253 LDS_QC_091023_1547_ISO
13:44:27 IMEI: 004401**********
13:44:27 Device ID: 5ADCE7D20F347C598A4D10C3271747B301A128CE
13:44:27 Minimum loader AID: 0002
13:44:27 Minimum software AID: 0001
13:44:27 Minimum EROM AID: 0001
13:44:27 Minimum customization AID: 0001
13:44:27 Minimum simlock AID: 0001
13:44:27 Serial number: CB511CWD9Q
13:44:27 Color: Brown
13:44:27 Phone model (from TA): X10a
13:44:27 Current CXC (from TA): 1227-4612_R1FA014
13:44:27 Current CDA (from TA): 1233-6929_R11A
13:44:27 Current FS (from TA): 1227-4607_R1FA014
13:44:27 e Failed!
13:44:27 . The action entered shutdown phase
13:44:27 . The action reported failure
Error code
# BC19D7F412BB5D61
Error details
---
3A E5 D1 81 28 3E E4 73 3E 27 47 6A 3E C9 EC 9E
FA F4 70 CF 05 54 5A EA CE 05 E8 7B 55 42 FC 1C
96 1E CE 20 66 01 FC 1D 5E 3A D8 EB E2 72 7D 82
74 5C B0 6F 2A 25 37 11 C3 1D 96 F6 8E 39 E4 81
7F B7 5A 9A E8 40 24 4D 82 81 E5 0E 39 16 82 C4
46 5D 30 05 BB 9C 3E 04 A0 A4 58 B7 92 D3 0D EE
87 8B 8E F3 DA 41 44 5D 9E 15 98 FD 60 AD C2 B5
---
Your phone is prototype, and brown so it's normal you can't update with SEUS. You can find prototype X10 firmware somewhere on this forum.
brutus* said:
what do you mean? I'm new to this forum, can you help?
---------- Post added at 01:48 PM ---------- Previous post was at 01:33 PM ----------
ID dump from omnius
Code:
Action journal
13:39:41 Identify
13:39:41 Shows detailed information about the connected phone.
13:39:41 Operating system: Microsoft Windows XP Professional Service Pack 2 (build 2600)
13:39:41 Application version: 0.23.3995
13:39:41 . The action name is 'Identification'
13:39:41 Selected phone type: Xperia™ X10
13:39:41 Selected connection method: USB EROM
13:39:41 i Instructions
13:39:41 i 1. Make sure the phone battery is charged to at least 50%.
13:39:41 i 2. Switch off the phone!
13:39:41 i 3. Remove the phone battery and wait at least 5 seconds before reinserting it!
13:39:41 i 4. Press and hold the return back button, then connect the cable to the phone!
13:39:41 . The action started waiting for the user
13:44:26 . The action finished waiting for the user
13:44:26 Connecting via SEMC USB Flash Device (USB2)...
13:44:26 Device driver version: 2.2.0.5
13:44:26 Detected chipset: QSD8250
13:44:26 Boot mode: EROM
13:44:26 EROM version: 1226-2253 LDS_QC_091023_1547_ISO
13:44:27 IMEI: 004401**********
13:44:27 Device ID: 5ADCE7D20F347C598A4D10C3271747B301A128CE
13:44:27 Minimum loader AID: 0002
13:44:27 Minimum software AID: 0001
13:44:27 Minimum EROM AID: 0001
13:44:27 Minimum customization AID: 0001
13:44:27 Minimum simlock AID: 0001
13:44:27 Serial number: CB511CWD9Q
13:44:27 Color: Brown
13:44:27 Phone model (from TA): X10a
13:44:27 Current CXC (from TA): 1227-4612_R1FA014
13:44:27 Current CDA (from TA): 1233-6929_R11A
13:44:27 Current FS (from TA): 1227-4607_R1FA014
13:44:27 e Failed!
13:44:27 . The action entered shutdown phase
13:44:27 . The action reported failure
Error code
# BC19D7F412BB5D61
Error details
---
3A E5 D1 81 28 3E E4 73 3E 27 47 6A 3E C9 EC 9E
FA F4 70 CF 05 54 5A EA CE 05 E8 7B 55 42 FC 1C
96 1E CE 20 66 01 FC 1D 5E 3A D8 EB E2 72 7D 82
74 5C B0 6F 2A 25 37 11 C3 1D 96 F6 8E 39 E4 81
7F B7 5A 9A E8 40 24 4D 82 81 E5 0E 39 16 82 C4
46 5D 30 05 BB 9C 3E 04 A0 A4 58 B7 92 D3 0D EE
87 8B 8E F3 DA 41 44 5D 9E 15 98 FD 60 AD C2 B5
---
Click to expand...
Click to collapse
please delete, thread moved to q&a : http://forum.xda-developers.com/showthread.php?p=17519604#post17519604
Hey guys... I need help!
Let me tell a little history about my E10a.
I'd buyed my phone with simlock enabled.
I'ved try many free ways to unlock sim, but nothing has works.
Looking at youtube and internet, i'ved found a way to do this using "Omnius for SE".
Worked fine using original kernel.
To unlock bootloader i'ved try to use Flashtool. But, because the simlock status was different to SEMC, the only way i found to flash TFT was using Omnius too.
Today I decided to update my phone.
I'ved download last version of Omnius, downloaded 2.6.32.60-nAa-jb-02 kernel.
Let's flash!
At first time, Omnius has show me a message telling me: You can't update your kernel because you don't have credits anymore and blablabla...
I forced to update checking the "Unsigned flashing".
So, now my phone wont power up anymore. I'ved try force shutdown using power + home, but nothing happens.
Sorry my very poor english. I'm from Brazil and I'm very nervous about this situation.
Plz anyone can help me? My experience with flashing android phones was since out'11. I'm not total n00b.
Next, the last log showed in Omnius:
Code:
Action journal
14:55:49 Flash
14:55:49 Allows to change languages supported by the phone and upgrade its firmware.
14:55:49 Operating system: Microsoft Windows 7 Home Premium Edition Service Pack 1 (build 7601), 64-bit
14:55:49 Application version: 1.40.4823
14:55:49 . The action name is 'Flash'
14:55:49 Selected phone type: Xperia™ X10 mini
14:55:49 i Instructions
14:55:49 i 1. Make sure the phone battery is charged to at least 50%.
14:55:49 i 2. Switch off the phone!
14:55:49 i 3. Remove the phone battery and wait at least 5 seconds, then insert the battery back to the phone!
14:55:49 i 4. Press and hold the return back button, then connect the cable to the phone!
14:55:49 . The action started waiting for the user
14:55:57 . The action finished waiting for the user
14:55:57 Connecting via SEMC USB Flash Device (USB2)...
14:55:57 Device driver version: 3.0.0.0
14:55:57 Detected chipset: MSM7227
14:55:57 Boot mode: EROM
14:55:57 IMEI: 01231300503142
14:55:57 Sending loader...
14:55:59 i Waiting for connection to the server...
14:56:05 Receiving news...
14:56:06 i News
14:56:06 i Omnius for Samsung v1.18 - Experimental unlock code read for Samsung Galaxy S II and similar, FREE
during test period
14:56:06 i Omnius 1 Year licenses purchased after 1st Oct 2011 now gained
unlimited android unlocking!
14:56:11 Unlocking loader...
14:56:16 i Unsigned flashing is enabled.
14:56:16 Writing file X10_V1_BLRelock.ftf...
14:56:20 e Failed!
14:56:20 . The action entered shutdown phase
14:56:20 . The action reported failure
Error code
# 973C36BE0FC7F2B7
Error details
---
67 5B 47 A0 8F 07 C1 3C D3 F0 24 A5 87 5E D7 31
FA 32 7D 70 C3 C1 C1 03 23 52 65 F4 D0 EF F9 26
4B 79 1D 41 7F 86 9F 12 8D 2E CB 30 27 D1 4E F1
35 1B 1D 90 31 FC 06 C3 68 3C 55 05 77 AE 99 7C
22 5D B8 92 E1 9A FF 76 56 F0 79 77 6A A7 C1 B1
69 6F 17 E9 AC F4 62 55 D7 5D 09 EA D2 37 6B 4E
D4 F5 3F 81 EC 15 62 FE 00 C7 C6 07 CB A7 56 97
97 07 F0 83 2D 71 34 9E 51 51 E8 0C 08 3A 90 87
E8 08 9B 61 0C 92 1E EA E8 CC C9 A3 42 8C 05 EB
3F C3 4D B1 E2 DF AC 69 7F 94 8C E6 C8 22 A7 C0
AA 82 AC 20 77 9F 6D F5 95 2B 28 E9 2D D7 D8 02
C5 1C FC 99 DD 13 2B AE 86 B2 D5 79 09 D2 19 76
09 09 DE 83 CF DB 81 7C 93 2C AB B8 B9 5A 17 67
3C BC 6D 31 11 56 51 9E C0 61 FB 06 C7 13 B9 9C
0B 3C D3 82 AB 45 71 45 CD 02 F5 32 5E B3 55 CC
F5 6A 23 B0 8F C4 F1 4C 83 8A F6 FE 74 38
---
Thank's a lot for any help!
Format /system
Hello,
did you format /system before flashing the new kernel?
http://forum.xda-developers.com/showthread.php?t=2138771:
Read through this post. Don't rush into flashing. Be sure you understand the process before you start or you risk damaging your device
This is a custom 2.6.32 kernel developed for Android Jellybean 4.x. This kernel only works for mimmi, a.k.a. X10miniPro
Do NOT try this kernel on other Android versions or phones - you are totally unsupported
This kernel uses a custom mtd partitioning with larger /system partition to hold the extra JB calories. If you are moving from another custom kernel, EXCEPT 2.6.29-nAa-jb to this one, you MUST first format /system /data and /cache via the embedded CWM recovery
Click to expand...
Click to collapse
gmamorim said:
Hey guys... I need help!
14:56:11 Unlocking loader...
14:56:16 i Unsigned flashing is enabled.
14:56:16 Writing file X10_V1_BLRelock.ftf...
14:56:20 e Failed!
Thank's a lot for any help!
Click to expand...
Click to collapse
You didn't flash the nAa-kernel but the Bootloader Relock kernel for the X10, your phone is probably bricked. If you can't get it into flash-mode anymore, it may need JTagging at a repair shop to get it back up working.
phone bricked, because it flashed the X10_V1_BLRelock.ftf, you will need to take it to a repair shop.
Do your PC react when connect the phone via USB?!
ferotakis said:
Do your PC react when connect the phone via USB?!
Click to expand...
Click to collapse
No... don't react
another newbie who bite the disaster...
Sent from my E10i using xda app-developers app
R3v3nGe said:
another newbie who bite the disaster...
Sent from my E10i using xda app-developers app
Click to expand...
Click to collapse
Thank you guy so much!
That's i want to hear...
...NOT!
Man, if you can't help, don't post things like this!
This is bull****! And won't help anybody!
Or maybe you think have a bigger post count is a great advantage!
"Another forum newbie..."
How old r u? 15?
hi bro does your x10 mini bootup or not??? sorry bro.... im only 14 years old and post count and rank does not matter here... this is a forum that has no competition...
Sent from my E10i using xda app-developers app
You hardbricked your phone, your bootloader is damaged.
JTAG is the solution, search for a repair center.
Hello all,
My device
I have a Rikomagic MK 802 IIIS mini PC with the following specs:
Model MK802 IIIS 8GB Dual Core
CPU RK3066 Dual Core - Cortex-A9 Up to 1.6GHz
GPU Quad- Core 2D/ 3D/ OpenGL ES2.0(AMD Z430)/ OpenVG1
OS Android 4.1
RAM 1GB DDR3
Memory 8GB Flash
Expansion Micro SD T-Flash(Maximum support 32GB)
Video Format WMV/ASF/MP4/3GP/3G2M4V/AVI/MJPEG/RV10/DivX/VC-1/MPEG-2/MPEG-4/H.263/H.264/1280*720P HD 30 fps, 1080P/720*480 D1 30fps
Audio Format MP3/WMA/APE/FLAC/AAC/OGG/AC3/WAV
Picture format Max.8000x8000 JPEG BMP GIF PNG
WiFi 802.11 b/g/n
Flash Supports flash 11.1
HDMI(male),Micro SD slot, USB host*1,USB OTG*1, USB power port; LED(Blue)
My primary problem (long story short): I managed to brick the MK802 IIS device in the process of installing Pi****u Linux on it. After trying to install the Linux kernel on the recovery partition manually, by doing from Android cmdline "busybox dd if=ug802recovkernel.img of=/dev/block/mtd/by-name/recovery bs=8192" and then "su" and "reboot recovery", I ended up with a non-booting system. I tried several times power off + power on cycles, but Android is not loading anymore. So, I would like to reflash the factory firmware on my device, to have the Android 4.1 booting again ... and I know about RKAndroidTool v1.35 for Windowses, but ...
... I am not using Windows OSes (better said, I avoid using them as much as I can, by trying to find *nix based solutions).
Therefore my main question: Is there Linux software to restore factory firmware on a Rikomagic MK802 IIIS device?
During my research, after googling for "rkandroidtool for linux" I found this promising link on our XDA community: http://forum.xda-developers.com/showthread.php?t=1286305
This "rkflashtool for Linux and rk2808, rk2818 and rk2918 based tablets" is reported to work fine by many, and later on in the above thread, user "frankjt" says:
there are good news, updated with ProductID 0x300a like this:
. . .
if (!(h = libusb_open_device_with_vid_pid(c, 0x2207, 0x300a)))
. . .
rkflashtool works on Cube's rk3066 tablets too (all functions: r, w, b).
Thanks to Ivop's excellent tool my Cube U30GT-H (firmware 1.02) is rooted now.
Click to expand...
Click to collapse
So, it seems this rkflashtool for Linux does a great job on rk3066 tablets, but is it working on mini PCs too?
Has anyone tried this tool on miniPC ? Preferably Rikomagic MK802 IIIS, but if you have experience on similar models, please share them here.
Is there a guide on how to reflash miniPCs with Linux software only? Please post it.
What are the hexadecimal addresses to be used when attempting to write an .img file on the Rikomagic MK802 IIIS mini PC?
Any advice, or feedback on these questions are very welcomed!
Regards.
Hi,
Doing a little bump of this thread.
After doing more google research, this time for "rk3066 flash tool linux" I've found:
armtvtech dot com and the rest of the link is: /armtvtechforum/viewtopic.php?f=66&t=350
slatedroid dot com and the rest of the link is: /topic/42826-flashing-rk3066-with-linux/
So definetly I'm not a singular case in my frustrations.
It seems that recommandations point to the rkflashtool that I mentioned in my previous post:
arctablet dot com and the rest of the link is: /wiki/index.php/Update_tablet_using_Linux (see the "Preparation" section)
Now the main question that remains: Anyone tested (successfully or not) Linux rkflashtool on a Rikomagic MK 802 IIIS mini PC?
Or, to put it simpler: Anyone tested Linux rkflashtool on any RK3xxx based android stick computer (aka mini PC) ?
If yes, please post your stories here.
PS: Sorry for the cryptic weblinks syntax, but I am still a new member, not allowed to post these ..
PSS(off-topic): Sorry for giving Pic Untu a "bad name" in the opening post, it wasn't my intention
Never mind, I was thinking of a different device.
Sent from my One X using xda app-developers app
---------- Post added at 08:49 PM ---------- Previous post was at 08:37 PM ----------
This person reports success with rkflashtool on an mk808: http://www.slatedroid.com/topic/460...08-from-linux/page__view__findpost__p__631970
ragesoss said:
Never mind, I was thinking of a different device.
Sent from my One X using xda app-developers app
---------- Post added at 08:49 PM ---------- Previous post was at 08:37 PM ----------
This person reports success with rkflashtool on an mk808: slatedroid com /topic/46001-writing-images-to-the-mk808-from-linux/page__view__findpost__p__631970
Click to expand...
Click to collapse
Thanks a lot, ragesoss!
I read the tutorial and the feedback, looks very promising!!
I'll test it myself on my MK802 IIIS and post the results here.
Very frustrating: seems that rkflashtool restore isn't working on Rikomagic MK802IIIS
First of all, the explanation for why I bricked my Rikomagic MK802 IIIS: when trying to install Pic Untu, I did that dd command on the recovery partition (see the first post in this thread for the exact command). Well, the procedure is not working like this because when accessing the mtdblock devices with normal *nix commands (dd, cat), the mtdblock Android driver is not handling I/O as usual and it causes data corruption on all the mtd device. That's why I bricked the device.
So, not having a backup before, I had to use a WindowsXP vmware VM with windows RK flashing utility. I restored the device to firmware "Rikomagic MK802IIIS 4GB, 8GB Recovery Software (20130121)" downloaded from rikomagic.co.uk.
Restoring was successfull so here I am with a fully functional Android which boots up OK. All fine for a day...
I decided to make a full device backup using Linux rkflashtool which I downloaded from the thread I mentioned in my first post (http://forum.xda-developers.com/showthread.php?t=1286305), this is the link: http://forum.xda-developers.com/attachment.php?attachmentid=785592&d=1321547155
I modified the source so that the rk3066 chipset is recognized (I added the 2207 usb vendor id).
The OS/computer I've used: Kubuntu 12.04 LTS 64 bit on a Thinkpad T420:
Code:
[email protected]:~# uname -a
Linux awesome 3.2.0-49-generic #75-Ubuntu SMP Tue Jun 18 17:39:32 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux
Now follows the copy/paste of commands & output of the backup operation, with the mention that: of course I put the device in flashing mode first, using paperclip + power-on cable in device's OTG connector linked to laptop :
Code:
[email protected]:~# ./rkflashtool r 0x00000000 0x01000000 > /mnt/media/mk802iiis_android_backup_20130706.bin
[email protected]:~# du /mnt/media/mk802iiis_android_backup_20130706.bin
8388608 /mnt/media/mk802iiis_android_backup_20130706.bin
[email protected]:~# du -h /mnt/media/mk802iiis_android_backup_20130706.bin
8.0G /mnt/media/mk802iiis_android_backup_20130706.bin
[email protected]:~#
[email protected]:~# hexdump -C /mnt/media/mk802iiis_android_backup_20130706.bin |head -10
00000000 50 41 52 4d 5b 02 00 00 46 49 52 4d 57 41 52 45 |PARM[...FIRMWARE|
00000010 5f 56 45 52 3a 34 2e 30 2e 34 0d 0a 4d 41 43 48 |_VER:4.0.4..MACH|
00000020 49 4e 45 5f 4d 4f 44 45 4c 3a 72 6b 33 30 73 64 |INE_MODEL:rk30sd|
00000030 6b 0d 0a 4d 41 43 48 49 4e 45 5f 49 44 3a 30 30 |k..MACHINE_ID:00|
00000040 37 0d 0a 4d 41 4e 55 46 41 43 54 55 52 45 52 3a |7..MANUFACTURER:|
00000050 52 4b 33 30 53 44 4b 0d 0a 4d 41 47 49 43 3a 20 |RK30SDK..MAGIC: |
00000060 30 78 35 30 34 31 35 32 34 42 0d 0a 41 54 41 47 |0x5041524B..ATAG|
00000070 3a 20 30 78 36 30 30 30 30 38 30 30 0d 0a 4d 41 |: 0x60000800..MA|
00000080 43 48 49 4e 45 3a 20 33 30 36 36 0d 0a 43 48 45 |CHINE: 3066..CHE|
00000090 43 4b 5f 4d 41 53 4b 3a 20 30 78 38 30 0d 0a 4b |CK_MASK: 0x80..K|
As you can see, the resulted backup file has 8 GB size, and the hexdump of it shows the usual stuff for a non-corrupted backup.
Note1: I avoided to "spam" the thread with the whole header of the hexdumped backup file, but I assure you that it has the boot command line with the size/offset of all the partitions. So, it is a backup successfully created.
Note2: The backup operation took about 25-30 minutes, no errors in the system logs.
After backup was done, Android still boots OK, all is fine. Until the nightmare came...
I decided to test the restore process, so I added the device once more in flashing mode (with paperclip & OTG), and did:
Code:
[email protected]:~/rk3066-rkflashtool/rk3066-rkflashtool-master/trunk# ./rkflashtool e 0x00000000 0x01000000
rkflashtool: info: interface claimed
rkflashtool: info: erasing flash memory at offset 0x00ffff00
[email protected]:~# ./rkflashtool w 0x00000000 0x01000000 < /mnt/media/mk802iiis_android_backup_20130706.bin
...
...
...
rkflashtool: info: writing flash memory at offset 0x00fffe80
rkflashtool: info: writing flash memory at offset 0x00fffea0
rkflashtool: info: writing flash memory at offset 0x00fffec0
rkflashtool: info: writing flash memory at offset 0x00fffee0
rkflashtool: info: writing flash memory at offset 0x00ffff00
rkflashtool: info: writing flash memory at offset 0x00ffff20
rkflashtool: info: writing flash memory at offset 0x00ffff40
rkflashtool: info: writing flash memory at offset 0x00ffff60
rkflashtool: info: writing flash memory at offset 0x00ffff80
rkflashtool: info: writing flash memory at offset 0x00ffffa0
rkflashtool: info: writing flash memory at offset 0x00ffffc0
rkflashtool: info: writing flash memory at offset 0x00ffffe0
Note1: Writing operation took 2 hours and 8 minutes, no errors in the system logs..
Note2: ... but it was the end of my working mk802iiis !
When I reconnected the device, Android won't boot, instead the device seems to enter the flashing mode again. I say it "seems" because I am not really sure, actually it should not even attempt to enter flashing mode because I'm not touching the little oriffice with the paperclip.
So that's it on short: Android does not start!
When I specifically manually entered flashing mode again, I tried to read several megabytes from near the start addresses of the flash memory. Unfortunately, I get garbage:
Code:
[email protected]:~# hexdump -C recoverytry.bin |head -10
00000000 ae e6 ff a7 75 26 3e 6f ee b7 d3 66 33 f7 e7 fa |....u&>o...f3...|
00000010 97 b4 e6 fe bf da 10 4e 70 b6 a7 d9 db 9f 3b b7 |.......Np.....;.|
00000020 6b 3d f6 7f fe ff bf 5e e1 af ef 3e ff df 93 f7 |k=.....^...>....|
00000030 d7 ee 3f ef 31 d2 cb cc ef eb db f7 f7 ff 7f e7 |..?.1...........|
00000040 cf 6d 96 e9 dd a5 d6 9f f7 11 67 ef 6d dc dd fd |.m........g.m...|
00000050 5e 4b f3 77 7d fd bd cd 9f 15 f9 17 83 fb f7 5b |^K.w}..........[|
00000060 b9 11 fd 61 b4 cd dd 93 b9 f7 de d7 f8 d1 9b ef |...a............|
00000070 76 fe bf 1f 67 77 f5 5f 67 e2 97 96 15 f7 ae 7f |v...gw._g.......|
00000080 e4 ce 7d e5 36 fb fe 56 ce e6 fb ca f3 f7 d0 37 |..}.6..V.......7|
00000090 3d af 49 cd d5 71 ff f9 33 db fe 34 f6 17 d3 1d |=.I..q..3..4....|
Compare the output above with the first 10 lines of my backup file posted earlier and you can understand what I mean by garbage.
So to resume:
1) I managed to create a correct backup of mk802iiis using rkflashtool ("rkflashtool r" worked as expected)
2) Rkflashtool failed to restore the backup ("rkflashtool w" doesn't work, at least not for restoring all 8 GB).
Does anyone experienced similar situations?
Is 8 GB too much to backup at once?
Is there some workaround for this?
Could be a PC problem or device problem?
Is 2 hours too long(or too short) for flashing 8 GB to NAND?
Please help.
Regards,
Lexminriko
An important omission from my previous post (my apologies for not realizing the importance of the following):
Using Linux rkflashtool on my Kubuntu 12.04 64bit I was able to successfully backup /restore partitions.
For example, I could restore recovery partition with the command:
Code:
./rkflashtool w 0x000010000 0x000008000 < /mnt/media/mk802iiis_original_recovery_part_20130706.bin
The "brickeage" occured only when I tried to restore all NAND in one step, with the command already mentioned in my previous post:
Code:
./rkflashtool w 0x00000000 0x01000000 < /mnt/media/mk802iiis_android_backup_20130706.bin
Main questions remain:
Anyone experienced similar situations on Rikomagic MK802 IIIS ?
Is there a way to fix this bricked device in Linux(with rkflashtool or other Linux software), given the command that caused the damage?
If you experienced similar troubles, please post.
Regards,
Lexminriko
lexminriko said:
Hello all,
My device
I have a Rikomagic MK 802 IIIS mini PC with the following specs:
Model MK802 IIIS 8GB Dual Core
CPU RK3066 Dual Core - Cortex-A9 Up to 1.6GHz
GPU Quad- Core 2D/ 3D/ OpenGL ES2.0(AMD Z430)/ OpenVG1
OS Android 4.1
RAM 1GB DDR3
Memory 8GB Flash
Expansion Micro SD T-Flash(Maximum support 32GB)
Video Format WMV/ASF/MP4/3GP/3G2M4V/AVI/MJPEG/RV10/DivX/VC-1/MPEG-2/MPEG-4/H.263/H.264/1280*720P HD 30 fps, 1080P/720*480 D1 30fps
Audio Format MP3/WMA/APE/FLAC/AAC/OGG/AC3/WAV
Picture format Max.8000x8000 JPEG BMP GIF PNG
WiFi 802.11 b/g/n
Flash Supports flash 11.1
HDMI(male),Micro SD slot, USB host*1,USB OTG*1, USB power port; LED(Blue)
My primary problem (long story short): I managed to brick the MK802 IIS device in the process of installing Pi****u Linux on it. After trying to install the Linux kernel on the recovery partition manually, by doing from Android cmdline "busybox dd if=ug802recovkernel.img of=/dev/block/mtd/by-name/recovery bs=8192" and then "su" and "reboot recovery", I ended up with a non-booting system. I tried several times power off + power on cycles, but Android is not loading anymore. So, I would like to reflash the factory firmware on my device, to have the Android 4.1 booting again ... and I know about RKAndroidTool v1.35 for Windowses, but ...
... I am not using Windows OSes (better said, I avoid using them as much as I can, by trying to find *nix based solutions).
Therefore my main question: Is there Linux software to restore factory firmware on a Rikomagic MK802 IIIS device?
During my research, after googling for "rkandroidtool for linux" I found this promising link on our XDA community: http://forum.xda-developers.com/showthread.php?t=1286305
This "rkflashtool for Linux and rk2808, rk2818 and rk2918 based tablets" is reported to work fine by many, and later on in the above thread, user "frankjt" says:
So, it seems this rkflashtool for Linux does a great job on rk3066 tablets, but is it working on mini PCs too?
Has anyone tried this tool on miniPC ? Preferably Rikomagic MK802 IIIS, but if you have experience on similar models, please share them here.
Is there a guide on how to reflash miniPCs with Linux software only? Please post it.
What are the hexadecimal addresses to be used when attempting to write an .img file on the Rikomagic MK802 IIIS mini PC?
Any advice, or feedback on these questions are very welcomed!
Regards.
Click to expand...
Click to collapse
You can use the official Linux tool called 'upgrade_tool' ... simply do a google search for 'linux upgrade_tool' and you'll get a several sites with guides and useful info about it.