[Q] sipdroid - Android Q&A, Help & Troubleshooting

i have setup a sipdroid, ipkall, pbexes, and sipsorcery account. however when i try and make a call it keeps asking for a password...?
i am not sure what i have done wrong and have followed the guide on this site and was wondering if someone could help?
also not sure how i need to configure gv or if that may have anything to do with it?? cause when you call my gv number it goes directly to gv and does not ring my mobile
Ok I have just told gv to use every time I make a call. Wasn't sure if that was something I should do or not? Also the password I entered for all my accounts this time worked, yet it said the call could not be completed?
***Edit***
Ok I think I have gotten alot further... It is no longer asking me for a password and is just now saying the call cant be completed as dialed. I have checked my sipsorcery account and it appears that im having an error loading my dial plan??? here is a copy of the plan i have below. also how can i get google to verify my sip number to forward my gv calls to the correct number?
appreciate all the help as i was just transferred to amsterdam and was looking for a low cost way to keep in touch with family and friends.
PHP:
# Copyright(c) 2010 Mike Telis
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
# http://www.apache.org/licenses/LICENSE-2.0
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
# License for the specific language governing permissions and limitations under
# the License.
# Click "View raw file" in the lower right for the best copy/paste view
AREA_CODE = '843' # my area code
GV_USER = '*********' # my GV e-mail address ([email protected])
GV_PASS = '*********' # my GV password
CB_NUMBER = '12064247339' # my 11-digit SIP number (only one)
SPEED_DIAL = { # my speed dial numbers
'1' => '19879879876', # Mom
'123' => '12345678901', # Work
'45' => '17479876543', # Gizmo BFF
'411' => '8004664411', # Google 411
'266' => '[email protected]', # CNN Headlines
}
begin
sys.Log "** Call from #{req.Header.From} to #{req.URI.User} **"
if sys.Out # if outbound call
num = req.URI.User.to_s # Get a string copy of the number to dial
num = SPEED_DIAL[num] || num # Substitute with speed dial entry, if any
case num
when /@/ then sys.Dial num # URI dialing
when /^[2-9]\d{6}$/ # Local call, 7-digit number
num = '1'+ AREA_CODE + num # prefix it with country and area code
when /^[01]?([2-9]\d{9})/ # US number with or without country code
num = '1' + $1 # add country code and truncate number to 10-digit
when /^(011|00|\+)(\d{9,})/ # international number
num = '+' + $2 # GoogleVoiceCall works with '+' prefix only
else sys.Respond 603, 'Wrong number, check & dial again'
end
sys.Log "Calling #{num} via Google Voice"
sys.GoogleVoiceCall GV_USER, GV_PASS, CB_NUMBER, num, '.*', CB_NUMBER =~ /^1747/ ? 7 : 1, 30
else # sys.Out
sys.Dial "#{sys.Username}@local"
end
rescue
sys.Log("** Error: " + $!) unless $!.to_s =~ /Thread was being aborted./
end