Related
First of all, I'm not sure if my Vibrant is "hardware-locked" or not - the battery has a date of 8/25/10 printed on it, the sticker behind the battery says "10.09." Either way, I cannot get into download mode. The phone was purchased 1 week ago today. I was simply attempting to disable the voodoo lag fix (using bionix 1.3 rom). I have tried every combination of getting the phone into download mode that I can find - is it possible? I sometimes think it's close to working because during the process a window on my computer pops up that says "hardware not installed correctly" which to me means that I was close. Someone please tell me if it's even possible to get my phone into download mode - it will start up, do the samsung galaxy animation, then go to black screen with the bottom buttons lit up. Thank you for any help you can provide - it makes me ill that I spent $500 on this 1 week ago and am now faced with a complete brick.
dsmithok said:
First of all, I'm not sure if my Vibrant is "hardware-locked" or not - the battery has a date of 8/25/10 printed on it, the sticker behind the battery says "10.09." Either way, I cannot get into download mode. The phone was purchased 1 week ago today. I was simply attempting to disable the voodoo lag fix (using bionix 1.3 rom). I have tried every combination of getting the phone into download mode that I can find - is it possible? I sometimes think it's close to working because during the process a window on my computer pops up that says "hardware not installed correctly" which to me means that I was close. Someone please tell me if it's even possible to get my phone into download mode - it will start up, do the samsung galaxy animation, then go to black screen with the bottom buttons lit up. Thank you for any help you can provide - it makes me ill that I spent $500 on this 1 week ago and am now faced with a complete brick.
Click to expand...
Click to collapse
Were you using one click root?
nomadrider123 said:
Were you using one click root?
Click to expand...
Click to collapse
yes, when i rooted it, i used 1-click
Try this:
Take battery out
Put battery back in
DO NOT TURN ON PHONE!
Plug in USB
Wait for the green battery screen
Hold vol+ and vol- at the same time
Hold power
When the battery screen goes black, let go power ONLY.
I had a HW locked phone and this method allowed me to get into DL mode--still couldn't get into recovery, but at least I could use ODIN. Was a null point as the phone is bricked and a new one is on its way...
When you say a new one is on its way, did T-Mobile exchange it under warranty even though it was rooted?
TheSneakerWhore said:
Try this:
Take battery out
Put battery back in
DO NOT TURN ON PHONE!
Plug in USB
Wait for the green battery screen
Hold vol+ and vol- at the same time
Hold power
When the battery screen goes black, let go power ONLY.
I had a HW locked phone and this method allowed me to get into DL mode--still couldn't get into recovery, but at least I could use ODIN. Was a null point as the phone is bricked and a new one is on its way...
Click to expand...
Click to collapse
Sent from my HTC Magic using XDA App
If the above doesn't work.
Plug in USB to PC only
Insure Phone is off
Hold in Vol + and -
Plug in USB to Phone Holding Vol + and -
Release Vol + and -
Walla you are in Download Mode
Neither of these methods worked. what are the chances of t-mobile performing an exchange for me if all else fails?
you could try this too, it worked for me.
remove battery and put it back in.
plug in usb
hold vol up, vol down and power button.
when you see the vibrant home screen, keep holding the three buttons until the screen turns dark.
let go the power button and vol up but keep vol down pressed, you should be in download mode.
hope this help.
Sent from my SGH-T959 using XDA App
Since we all seem to have our own variations of this method, I can tell you the one that worked for me 99.99% of the time on the first try when I was stuck at the Phone ! Computer screen.
1) Remove battery
2) Hold Vol - and Power
3) Insert battery while holding these buttons
4) Plug in USB if it works.
Some have reported T-Mo swapping the device due to the inability to access download/recovery mode, but it doesn't seem to be something they will regularly do. Others have been successful by using the inaccurate GPS issue to get a replacement. Specifically by insisting it is not just inaccurate, but downright non-functional.
dsmithok said:
When you say a new one is on its way, did T-Mobile exchange it under warranty even though it was rooted?
Sent from my HTC Magic using XDA App
Click to expand...
Click to collapse
Yea...I tried relashing the stock rom using ODIN--for 4 hours over and over. It said "successful" in ODIN, but the phone was toast (would go past S boot screen then nothing. Just walked into TMO, said it "just would not do anything" with a feigned puzzled look and after a amateur cursory inspection the rep. just did his thing on the computer and a new phone is being sent to my house via UPS.
I've tried every possible combination ... literally tried everything and this quote from this thread http://forum.xda-developers.com/showthread.php?t=771247 just comfirmed it to me
METHOD 4: STUCK AT PHONE ! COMPUTER:
(and are not able to use vol+ vol- methods to access downloader/recovery)
CALL TMOBILE AND BEG FOR THEM TO REPLACE UR PHONE..
i cant believe its that easy to mess up your vibrant, my g1 never gave me a problem
did you try:
1. Phone starts OFF
2. Hold volume up + volume down buttons
3. Plug in USB cable
That is how I get into download mode. You don't ever hit the power button and you plug in the USB cable WHILE holding down the volume buttons.
El Cipitio said:
I've tried every possible combination ... literally tried everything and this quote from this thread http://forum.xda-developers.com/showthread.php?t=771247 just comfirmed it to me
METHOD 4: STUCK AT PHONE ! COMPUTER:
(and are not able to use vol+ vol- methods to access downloader/recovery)
CALL TMOBILE AND BEG FOR THEM TO REPLACE UR PHONE..
i cant believe its that easy to mess up your vibrant, my g1 never gave me a problem
Click to expand...
Click to collapse
El Cipitio!!!!!!!
[do you eat ashes?] j/k
anyway... I'm sure there's a fix.
I *think* there's a fix.
ndhr3d said:
did you try:
1. Phone starts OFF
2. Hold volume up + volume down buttons
3. Plug in USB cable
That is how I get into download mode. You don't ever hit the power button and you plug in the USB cable WHILE holding down the volume buttons.
Click to expand...
Click to collapse
This is the way, no power just volume up an volume down, or just volume down with the same method. Be sure you remove your sd and sim cards also.
Sent from my Vibrant running Bionix Final w/Jacs and Voodoo using XDA App
What has always worked for me is:
1. Power off the phone
2. Plug it in via USB
3. Wait for the green battery symbol to pop up
4. Hold vol. down and the power button until the Download screen pops up.
MrDragomir said:
What has always worked for me is:
1. Power off the phone
2. Plug it in via USB
3. Wait for the green battery symbol to pop up
4. Hold vol. down and the power button until the Download screen pops up.
Click to expand...
Click to collapse
I have a hardware locked phone and have been stuck at the phone to computer link screen (a rather nervous place to be, I might say). First you need to take the battery out (to turn the phone off). Then you plug in the USB with the battery out. Then you put the battery in. You need to get the battery charging indicator, and I can't remember if you need to unplug/replug USB for that or not. Then you hold down both volume buttons and the power button. The *second* time you see Vibrant (phone reboots twice) let go the power button. You should end up in download mode.
I have the same issue, and when i try to do this:
JJMT said:
I have a hardware locked phone and have been stuck at the phone to computer link screen (a rather nervous place to be, I might say). First you need to take the battery out (to turn the phone off). Then you plug in the USB with the battery out. Then you put the battery in. You need to get the battery charging indicator, and I can't remember if you need to unplug/replug USB for that or not. Then you hold down both volume buttons and the power button. The *second* time you see Vibrant (phone reboots twice) let go the power button. You should end up in download mode.
Click to expand...
Click to collapse
it resets back to the battery icon.
Basically, im in the exact same situation as El Cipitio. i tried EVERYTHING!!! no luck at all...
Can adb still see your phone? I'm guessing no, but if it can just use "adb reboot downlaod".
Then again.... you guys are aware that the "hardware locked" issue was fixed almost two months ago right? One of the members posted a thread with a zip and the JI6 update also fixed this. There fore if you didn't flash either you should call Tmo, but if you have, then you're just doing it wrong... GL either way.
ahbad said:
I have the same issue, and when i try to do this:
it resets back to the battery icon.
Basically, im in the exact same situation as El Cipitio. i tried EVERYTHING!!! no luck at all...
Click to expand...
Click to collapse
One other thing to try is to remove the sim and external sd card and try the instructions I posted again. Really, if you get the pc to phone connection icon, you can get it into download mode and use odin to flash.
Dont waste your time fellas with trying to get,into recovery/download mode. If its anything like my hardware locked vibrant there isn't a key combo that will work. Probably thinking that your doing something wrong,YOUR NOT.
Im using my vibrant on att so I didn't consider calling tmobile. I actually called samsung, and after 5min on the phone they agreed to repair/replace for free. They recieved my phone on saturday amd I got it back that following thursday.
Save yourself a headache and sending
Sent from my SGH-T959 using XDA App
Might be a fix????
intruda119 said:
Dont waste your time fellas with trying to get,into recovery/download mode. If its anything like my hardware locked vibrant there isn't a key combo that will work. Probably thinking that your doing something wrong,YOUR NOT.
Im using my vibrant on att so I didn't consider calling tmobile. I actually called samsung, and after 5min on the phone they agreed to repair/replace for free. They recieved my phone on saturday amd I got it back that following thursday.
Save yourself a headache and sending
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
Some one posted this in another thread. My brick got sent back before I could try this.
http://forum.xda-developers.com/showthread.php?p=8822843
This is how I got it to work....
1. Take out the battery
2. Plug the USB into the phone
3. Plug USB into the PC
4. Hold down the Volume up/down + Power button with one hand
5. Put the battery back in with the other hand
6. Wait for the phone2pc icon to flash 2 times and on the second time when the screen goes black release only the POWER BUTTON
7. When you see the digging Android you can let go of the Volume buttons
That is the only way I could get it to work
No, I can't get it into adb mode. The phone bootup screen comes (vibrant, the pink tmobile thing, then galaxy s), but then it goes black. The computer doesn't find anything during this time.
I don't really have time to do the soldering, so i'll try calling samsung. Problem is i live in toronto and bought this thing for cash, so i have no clue what to tell samsung lol. If that doesnt work, i guess soldering it is...
Try this:
unplug, remove battery, remove sim/sd cards
hold down volume control buttons
plug into wall adapter (usb charger - not to computer but to outlet)
pop battery in
Took me a couple tries, but I got my Vibrant into dl mode from nothing but a black screen (I could not register charging, or "phone ! pc" error)
intruda119 said:
Dont waste your time fellas with trying to get,into recovery/download mode. If its anything like my hardware locked vibrant there isn't a key combo that will work. Probably thinking that your doing something wrong,YOUR NOT.
Im using my vibrant on att so I didn't consider calling tmobile. I actually called samsung, and after 5min on the phone they agreed to repair/replace for free. They recieved my phone on saturday amd I got it back that following thursday.
Save yourself a headache and sending
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
I'm am referencing more to the fact that these phones are not "hardware" locked. Hardware would refer to the volume & power keys not working... When your phone is on they work right?
Like stated before, IF, your phone is "hardware locked" look to either use the script or flash JI6. This way you re-gain functionality of the recovery & dl mode before flashing anything!
Ditto.. i got mine back after flashing without removing the lag fix.. never again... i will wait for froyo.. if that ever happens...
May I ask what bricked you?
nomadrider123 said:
Some one posted this in another thread. My brick got sent back before I could try this.
http://forum.xda-developers.com/showthread.php?p=8822843
Click to expand...
Click to collapse
The brick, in atleast my case, was from untimely removal of the phone from USB during Download mode of flashing stock kernal via Odin. This method described in the link above worked for me in getting the phone to boot into download mode without the use of the hardware keys (aka hardware locked phones). I also contacted Samsung directly through their Galaxy tech line, and they said I could send it in for free with their shipping label and if they couldn't flash back I could get a replacement, but there was a about a 2 week window I would be looking at without a phone, so I tried the homemade download-boot circuit and it worked perfectly.
THIS IS YOUR FIX!!!
I just did this the other day. If you are still stuck with the phone/!/computer screen do the following:
1.Hold the volume up/down + power button simultaneously
2.The screen will go black / reappear/ then go black again...when this happens, release the power button and continue holding the volume up/down button
3.Welcome back to download mode!
Please Mods, please lock this thread
Please stop waisting everyones time with stupid instructions.
When a phone is "hardware locked" (that is, bad flash/missing the sbin file.....)
YOU CANNOT GET INTO DOWNLOAD MODE OR RECOVERY WITH ANY KEY COMBINATION.
Stop waisting your time trying anything cause its not going to work. And thats a Fact.
Final fix and summary to this thread,
Either call T-mobile or Samsung.
Finish.
Hello, I was trying to flash my phone using ODIN and Eugene's 2.2 ROM. Things were going well, until I accidentally nudged my computer, which apparently has a very loose USB port. ODIN tells me that the phone disconnected. Plugging and unplugging the phone again would not work, so I was forced to do a battery pull. I am now stuck at the Phone /!\ PC screen, and the Volume Up, Down, Power button sequences do not work. Am I totally screwed?
Thanks.
ionstream said:
Hello, I was trying to flash my phone using ODIN and Eugene's 2.2 ROM. Things were going well, until I accidentally nudged my computer, which apparently has a very loose USB port. ODIN tells me that the phone disconnected. Plugging and unplugging the phone again would not work, so I was forced to do a battery pull. I am now stuck at the Phone /!\ PC screen, and the Volume Up, Down, Power button sequences do not work. Am I totally screwed?
Thanks.
Click to expand...
Click to collapse
No, youre not screwed. Remember that the Vibrant is nearly impossible to kill. Reboot and hold both volume buttons + power at the same time and when you see "Vibrant" on your screen turn to black then let go of power and Download mode will pop up. Then do Odin.
My phone went to that screen as well. Didn't get there the same way but here's what got me to download mode...
Pull battery, sim card, and sd card. Put battery back in but do not turn on. Plug usb cable into computer and phone. Start Odin. Hopefully your phone shows the charging image, now hold both volume buttons and power button until the vibrant screen comes up. Immediately release the power button, keep holding other two buttons. It should boot into download mode.
Flash with Odin like normal and then replace sim card and sd card. I had to do this twice yesterday.
Typos and other gibberish courtesy of Swype
Unfortunately when I plug in the USB cable after putting the battery in, it does not show the charging screen, but the Phone /!\ PC screen. Additionally, starting up the phone while holding the Volume Up, Down and Power buttons also brings me to the same screen. It seems like my phone is the kind that does not have the 3 button download mode option. Is there any other way to get out of this screen?
Well, I've never had that situation but I'm pretty sure it's fixable. The Vibrant is almost impossible to brick.
You'll gave to keep searching and wait for someone more knowledgeable than me...
Typos and other gibberish courtesy of Swype
Well the help is much appreciated anyways! I hope I don't have to hack a microUSB cable with soldered resistors and such. Does anyone have any ideas?
ionstream said:
Well the help is much appreciated anyways! I hope I don't have to hack a microUSB cable with soldered resistors and such. Does anyone have any ideas?
Click to expand...
Click to collapse
i just fixed my phone when it was like that, just plug the usb cable in, hold both vol buttons and the power button, it may take a minute or so, but you will see your screen go completely black, let go of the power button and keep holding the vol buttons, and you will get in download mode, trust me, i panicked just like you, just keep trying it, it took me about 30 minutes to get in download mode
Thanks for the advice! Should the battery be in while I'm doing this? If so, should I put the battery in before the usb cable?
ionstream said:
Thanks for the advice! Should the battery be in while I'm doing this? If so, should I put the battery in before the usb cable?
Click to expand...
Click to collapse
yes put the battery in, and then plug in the usb cable
Heres whats happening right now: when I plug in the USB cable, hold down the Volume Up, Down, and Power buttons, a few seconds later the screen will go black, at which point I unpress the power button. But this does not bring me to the download mode, it just brings me back to the error screen. If I press all 3 buttons again, as before eventually the screen will turn to black, but it will always bring back the error screen. It also behaves the same whether the USB cable is plugged in or not. I suppose this is progress, but am I doing something wrong? Arent I just supposed to let go of the power button when its black?
I am having the same problem except I am only getting the Vibrant screen. I have been trying to fix this for hours, and am about ready to go swap the damn phone out. It is literally driving me crazy. NONE of the methods to get to download mode are working.
[A] I'm screwed, arent I. (Brick, Phone ! PC, no download mode)
From what I hear, 1 in 3 Vibrants won't go into download mode in this situation. Mine does it just fine, my buddy's phone - no dice. I bricked it, so I fixed it. The solution was the spare micro usb + solder + 301k resistor(s). It worked perfectly, the 1st time. I'm a skeptic turned believer! It cost about $8.00 for the cable & resistors at Fry's Electronics.
Sigh, I guess I'm going to have to build this thing then, which is great because the nearest radio shack is 5 miles from my place. Ah well, better than having no phone.
I commend you in your efforts! Once you get out of this you'll be truly unbrickable. GL!
I was discouraged by the fact that I was far from a Radio Shack, but I looked online and it turns out you can actually create a resistor by drawing a line in pencil on a piece of paper. I have a multitester and stripped phone wire, and was able to duct tape the wire on specific points to get 302Kohms! Unfortunately thats where the project stopped, because I don't have a spare microUSB cable to butcher haha. And a friend offered to drive me to radio shack so I don't have to be the poorest electrician ever.
I might still try that method though! Just for kicks.
Try this
Ok, so I see some ppl offered advice on how to get into download mode. That is great, but I found their methods to be very different from mine. So give this a go and see if it works before you go into MacGyver mode.
Please note: DO NOT PRESS THE POWER BUTTON EVER DURING THESE INSTRUCTIONS.
1. Take back cover off phone
2. Remove the battery
3. Plug the USB into your computer, and then the other end into your phone.
4. Hold down both volume buttons (do not press the power button!) and while holding them both down put your battery back in.
5. Hold in place for approximately 2 seconds.
You should now be in download mode. Keep in mind, you said that your usb on your computer is "loose." Be extra careful not to bump it or anything b/c if the phone isn't being recognized as plugged into a computer download mode will not work. Hope this helps!
I got back to stock via odin. I tried to re root and it will not let me. When I do adb reboot recovery I click on reinstall packages and it takes me to cwm recovery. I then click instal from sd card and click on update.zip says it installed but didn't after reboot.
Sent from my SGH-T959 using XDA App
Hi, I had that problem before, here is what I did to fix my vibrant. take sim, microSD, and battery out of the phone. Connect the microusb and turn on odin. hold down volume+, volume-, and power down. while holding them down put in the battery and it should get to download mode once boot. also odin should detect it.
Hope that work.
I have returned! Unfortunately none of the many volume up/down button techniques were able to get me into download mode, as I must have a hardware locked phone. Fortunately though, I was able to get a ride to Radio Shack, where I spent 27 dollars on a microUSB adapter, a pack of resistors and solder. The adapter and solder I didnt even use. I twisted together 3 100kohm resistors and 1 10kohm resistor (my multitester read 305kohm total, I guess thats the 5% tolerance). I never ended up using the microUSB adapter because when I cracked it open, I couldnt find pins 4 and 5, so I cracked open the samsung USB cable that came with the phone. Plugged it in, tapped the two ends of the resistors awkwardly to what I beleived to be 4 and 5, and it worked! First thing I did was get Eugene on there, put the casing back on the USB cable (which still works!) and then marked that USB port to never be used again. The phone works great now! Thanks to however discovered that 301Kohm trick, you are a life saver.
Thanks all!
Volume Down + Home + Power.
Works for me everytime Best of luck man
Hi,
This is about my Samsung Vibrant. I flashed a new rom onto it and after the regular installation the screen turned black and would not turn back on. Like nothing works. No lights, no anything, like the power button hasn't even been touched.
Is my phone bricked? Is there any fix to this?
Thanks
what do you mean black screen? as in no power at all? Even when charging the phone?
Yeah. Like it looks like the phone is off. Just black
have you tried removing the battery then going to DL mode?
I've tried all three button combinations.
Removing the battery and then holding the two volume buttons and inserting the battery then pluging it into my computer.
Nothing seems to work. The phone is unresponsive and the screen remains black the whole time. The four lights on the bottom of the screen don't even light up.
Hmm, let's wait for the others but i think....
Guide in signature should help
2. Remove everything from your phone (SD card, sim, battery).
3. Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
4. Press and HOLD vol. up and vol. down.
5. As you are HOLDING these buttons, reattach your battery.
6. You should be in Download Mode.
This is under the NO-BOOT phones.
I tried and it doesn't put it into download mode. If I can get it back to download mode it would be golden.
I think they've rigged things to force download mode haven't they?i don't know if it will help but it might be worth a shot
Still flashing , thanks to odin
Check my guide under the troubleshooting section, it should have a link to the "Soldering Method" and THAT will force it into DL mode.
But I'd advise you to CAREFULLY follow my steps again before spending time and money on the soldering methdo x) Just a thought
Originally Posted by TheBeano View Post
If your phone screen is always black, that is it does not display the white Galaxy S/Samsung/AT&T logo when you switch it on, then sorry, this jig will not help you.
[/URL].
So...... yeah
My phone is a Telus t959D
I am stuck at the phone--!--PC screen. 3 button combo does not work, please do not give me other 3 button combos because it will not work. I think i need to fix this battery problem first and the download mode will come itself.
Plugging it in to the usb gives me a screen with an empty grey battery, with the progress circle in the middle frozen.
I cannot go into download mode because when i connect the usb, the grey battery pops up.
If i turn the phone on with no usb, i get the phone--!--pc screen.
http://www.youtube.com/watch?v=8ZxCzxb5RT8
so even with the battery pulled you still get the battery icon?
pspjunior said:
My phone is a Telus t959D
I am stuck at the phone--!--PC screen. 3 button combo does not work, please do not give me other 3 button combos because it will not work. I think i need to fix this battery problem first and the download mode will come itself.
Plugging it in to the usb gives me a screen with an empty grey battery, with the progress circle in the middle frozen.
I cannot go into download mode because when i connect the usb, the grey battery pops up.
If i turn the phone on with no usb, i get the phone--!--pc screen.
Click to expand...
Click to collapse
Uninstall your current installation of Kies and any samsung drivers, restart your computer, reinstall Keis from http://www.samsung.com/ca/consumer/...TLS/index.idx?pagetype=prd_detail&tab=support and download the drivers via that, restart again and check the results.
hey sendan thanks a lot. Before i do what you said i should do, how will the computer recognize my phone if it is only on the phone!PC screen because kies cant even recognize it right now?
droidstyle said:
so even with the battery pulled you still get the battery icon?
Click to expand...
Click to collapse
No, without the battery the screen is just blank because it is off if that is what you meant. If you meant if i pull it out and put it back in, then it goes to the Phone!PC screen without a USB connected. If i reinstall the batter again WITH a usb, then it freezes at a grey battery.
pspjunior said:
No, without the battery the screen is just blank because it is off if that is what you meant. If you meant if i pull it out and put it back in, then it goes to the Phone!PC screen without a USB connected. If i reinstall the batter again WITH a usb, then it freezes at a grey battery.
Click to expand...
Click to collapse
you suppose to get into download mode without the battery in.
power off and pull battery
plug usb cable in
hold vol down until the yellow triangle appears
I took out the battery, plugged in the usb, and held the volume down button. Screen stays black (left the battery out)
pspjunior said:
I took out the battery, plugged in the usb, and held the volume down button. Screen stays black (left the battery out)
Click to expand...
Click to collapse
ok.. Are you using the factory usb cable? If so, then unfortunately you may need to do one of the two things:
http://forum.xda-developers.com/showthread.php?t=1288093
or get a "Jig" and jumper the usb pins.
alright i'll try those out. And i recorded myself doing the methods and the screens i get.
http://www.youtube.com/watch?v=8ZxCzxb5RT8
Okay I watched your video...instead just take the battery out and DON'T put it back in, your computer will supply the power. Now make sure your holding the volume down button BEFORE you plug it in, and continue holding.
Or plug it in the wall adapter if you don't have powered USB Ports.
Sent from my GT-P7510 using xda premium
Alright, the screen just stays black when i do that. when i plug it into the wall or into the computer same thing
pspjunior said:
Alright, the screen just stays black when i do that. when i plug it into the wall or into the computer same thing
Click to expand...
Click to collapse
I figured, was just making sure you went through all the options before you start messing with the more advanced stuff, good luck.
sendan said:
I figured, was just making sure you went through all the options before you start messing with the more advanced stuff, good luck.
Click to expand...
Click to collapse
i bought the phone from a really good friend at a steal price of 40 bucks. I'll just give it back to him because he got it for free. It's just going to make me feel bad because anybody else in the future who has the same combination of problems might not be able to find a solution , but thanks a lot everybody! i'll just try and find a captivate or something
pspjunior said:
i bought the phone from a really good friend at a steal price of 40 bucks. I'll just give it back to him because he got it for free. It's just going to make me feel bad because anybody else in the future who has the same combination of problems might not be able to find a solution , but thanks a lot everybody! i'll just try and find a captivate or something
Click to expand...
Click to collapse
Actually I did a bit of reading, since I got stuck at that screen a long time ago, and I remember connecting to Odin at the Phone ! PC screen. You should be able to connect to Odin because it's still considered download mode. If it doesn't work you should re-install the drivers that I posted before.
I can almost guarantee it will work unless something else is really broken.
Edit: Here's some reassurance to motivate you - http://forums.androidcentral.com/t-...s-hacks/79287-odin-works-phone-pc-screen.html
there's a feature in heimdall to try and kick it out of that screen.
Sent from my Incredible 2 using XDA App