Problems with shutting down - Galaxy S II Q&A, Help & Troubleshooting

If i shut down the phone, after a few seconds on display appear charge and battery overheating image. Phone can only be enabled if go in recovery, and press reboot. Can not turn off. Any ideas, but not SC?

lTzXl said:
If i shut down the phone, after a few seconds on display appear charge and battery overheating image. Phone can only be enabled if go in recovery, and press reboot. Can not turn off. Any ideas, but not SC?
Click to expand...
Click to collapse
Difficult to help with no specific information about the ROM, kernel, etc. running on your phone.
Since when do you have this issue?
What has happened just before this problem appeared the first time?
Just as theoretical suggestions:
1. Start into recovery mode, wipe cache partition.
2. Shut down the phone.
Pull out the battery.
Leave it out for about 5 minutes.
(Just to be sure that everything "cooled" down and CPU is fully out of any voltage and current.)
Then put the battery back into the phone.
3. If nothing helps, flash a stock ROM.
Then start into recovery mode and do a factory reset.
(So backup everything you do not want to lose before flashing.)
Good luck !

problem arose in the morning, after charging the phone. Reset did, flash another firmware. None of this helps.

Related

[Q] Can't shutdown

I can't turn my device off my Galaxy S2.
If I press turn of after clicking the power button, it will turn of, and reboot again. I decided to do the same by entering in cwm and asking it to turn of the phone. It also rebooted.
If I take the battery off, it reboots as soon as I put it on again.
I'm currently on KI8, with speedmod kernel. But happened the same with KI3 a few minutes ago...
Any guess?
Thank you so much.
damn it! I did a full wipe. And thought it had worked, because it was off, but just when I was posting that the problem was fixed, the phone turned on by it self automatically.
Any solution? I'm getting crazy!
any help on this?
EDIT: wipe chache and dalvik cache

My Amaze refuses to start up

My Amaze has been off for about a week or two and now it wont even power on.
If I press and hold the power button I get no indication that it is doing anything. However, if I press the buttons on the bottom of the screen I get a slight vibration indication that it is indeed getting power to it. Tried booting into recovery with no luck.
Any thoughts?
What recovery are you using? I know most recoveries don't support charging while off. I suggest 4EXT but you will need to charge the battery externally first in order to flash it. Good luck.
do you have an external battery charger to charge the battery out of the phone?
did you try to charge the battery ?
Here's an interesting update.
Was able to plug it in USB and using ADB restart into recovery. From recovery I hit restart and the phone booted up like normal.
BUT, about 5-10 seconds in Android it reboots again back to the black screen with the vibrating buttons. Had to run back to work so I wasn't able to play around with it anymore than that.
BiznessMan said:
Here's an interesting update.
Was able to plug it in USB and using ADB restart into recovery. From recovery I hit restart and the phone booted up like normal.
BUT, about 5-10 seconds in Android it reboots again back to the black screen with the vibrating buttons. Had to run back to work so I wasn't able to play around with it anymore than that.
Click to expand...
Click to collapse
if your running a custom rom maybe it got corrupted somehow, happens to my phone often due to the fact im trying to find a way around to cloning one rom to another phone, try to reset your phone back to stock by flashing a ruu stock rom or a different rom, flash 4EXT and wipe everything from the phone (including sd card) don't forget to check and realign the partitions and then toggle usb mode and put the rom on the sdcard and flash it , hope that helps
Ninjistix said:
if your running a custom rom maybe it got corrupted somehow, happens to my phone often due to the fact im trying to find a way around to cloning one rom to another phone, try to reset your phone back to stock by flashing a ruu stock rom or a different rom, flash 4EXT and wipe everything from the phone (including sd card) don't forget to check and realign the partitions and then toggle usb mode and put the rom on the sdcard and flash it , hope that helps
Click to expand...
Click to collapse
Thanks for the reply but I can't even get it to recognize via USB anymore
Buttons still vibrate, screen is still black. I can't get anything to work on it
BiznessMan said:
Thanks for the reply but I can't even get it to recognize via USB anymore
Buttons still vibrate, screen is still black. I can't get anything to work on it
Click to expand...
Click to collapse
Battery pull, hold volume down(or is it up? I work on too many android phones..) and power button and it should boot into bootloader. From there reboot into recovery. Flash a custom rom of your choice after doing a full wipe. Problem should be solved unless there is a hardware issue, at which point it must have been dropped, battery issue, etc..
What it really seems like is your battery doesn't have enough juice to sustain power, (I get bootloops when my battery goes really low and I try turning it on). Just let it charge a bit and if the battery isn't holding its charge, then time for a new battery
Sent from my Amaze using xda app-developers app

S2 Not Booting

So yesterday morning I went to turn on my phone, but nothing happened. It was on the charger all night so it should have been a full battery.
Here are my symptoms:
1) AC plugged in without battery - Phone's screen turns on for a second, turns off, and then repeats.
2) AC plugged in with battery - Phone will start to charge (has the loading symbol in the battery), but then turns off immediately. It cannot boot into recovery. It CAN boot into download mode, but my computer will not recognize it to restore the phone with odin.
Any ideas?
I don't have an official upgrade until October, but I'm going to call customer service to try and get them to bump the date up so I can get a new phone.
First possibility to suspect is a failed battery. If you know someone else with an s2, ask to borrow their battery temporarily to see if your phone will boot. Or perhaps go to an AT&T store to see if you can borrow a battery.
If it's not the battery, then the next step to try is to boot into download mode with the battery out of the phone to see if Odin will recognize the phone with the battery out. With the battery out of the phone and the USB cable plugged into the computer, hold down the vol down button while plugging the USB cable into the phone. The computer will supply the power. This assumes that you have the proper "Samsung USB driver for mobile phones" installed on your PC.
That's a start.
I am having the same issue with my s2. i had shostock installed on it a few weeks back and it was working fine. then it just stopped working. i tried rebooting but it keeps on going on bootloops. I tried using odin to flash back to stock but no go, just bootloops. kies just dont work for me. i know it isnt the battery cuz i have the charging cradle to charge the battery and the phone goes to odin mode without the battery. Any help is appreciated.
sfb14 said:
I am having the same issue with my s2. i had shostock installed on it a few weeks back and it was working fine. then it just stopped working. i tried rebooting but it keeps on going on bootloops. I tried using odin to flash back to stock but no go, just bootloops. kies just dont work for me. i know it isnt the battery cuz i have the charging cradle to charge the battery and the phone goes to odin mode without the battery. Any help is appreciated.
Click to expand...
Click to collapse
It sounds like you got a successful flash of stock. Boot into recovery and perform a wipe data/factory reset.
creepyncrawly said:
It sounds like you got a successful flash of stock. Boot into recovery and perform a wipe data/factory reset.
Click to expand...
Click to collapse
I just did. Still no boot.
sfb14 said:
I just did. Still no boot.
Click to expand...
Click to collapse
OK. Did the flash to stock succeed? In other words, you got a pass in odin?
Which version of SHOstock was installed, the latest? And which version of stock did you flash?
i flashed SHOstock v3 before all of this happened. i flashed ucle5 stock rooted. battery icon flashes capacitive keys blink over and over again. if i unplug it nothing happens. i may have to try UCKH7 once im done downloading it.
** after flashing KH7, i go to recovery to wipe/factory reset... there is a message saying
Installing Multi-CSC...
"can't access to '/system/csc/ATT/system/'
Successfully applied multi-CSC
sfb14 said:
i flashed SHOstock v3 before all of this happened. i flashed ucle5 stock rooted. battery icon flashes capacitive keys blink over and over again. if i unplug it nothing happens. i may have to try UCKH7 once im done downloading it.
** after flashing KH7, i go to recovery to wipe/factory reset... there is a message saying
Installing Multi-CSC...
"can't access to '/system/csc/ATT/system/'
Successfully applied multi-CSC
Click to expand...
Click to collapse
This is sounding a bit like nand read/write corruption, which is fixable. Try this:
1)Go to this post and download the Tar version of Siyah 2.6.14 Kernel. Flash it in PDA without ticking Re-Partitioning.
2) Successful? Nice. Next, flash the full stock Gingerbread distribution from the Download Repository, I777UCKH7 including the bootloaders and everything, in the PDA slot.
3) If that is successful and boots normally you are done. If it is not, then:
4) Download the SBL Bootloader from the Download Repository. Flash it as PDA in ODIN, without ticking Re-Partitioning.
5) Flash the Kernel, as in step 1.
6) Flash the full stock Gingerbread distribution, as in step 2.
Will try that later. Thanks for your help!
Sent from my SAMSUNG-SGH-I337 using xda premium
still no luck.. i did everything odin says "PASS" but it just wont boot. i'm going to try and get a different battery and see if that works.
thanks for your help sir. :good:
sfb14 said:
still no luck.. i did everything odin says "PASS" but it just wont boot. i'm going to try and get a different battery and see if that works.
thanks for your help sir. :good:
Click to expand...
Click to collapse
Going through the exact same issue with my kids phone with the same results. Tried creepy's 6 steps, but still no luck.
I think it was caused by my kid killing the battery.
update: got it to boot into custom recovery, then reflashed ROM. It stills acts weird though. Very laggy.
http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-s-ii-at-t-usb-port-repair/
Sent from my SGH-I777 using xda app-developers app
Having a very similar issue here.. Battery icon flashes then black screen. Boot to download mode.. Push up arrow, black screen. Computer does not register device connected.
Sent from my SGH-I997 using xda app-developers app
jvick920 said:
Having a very similar issue here.. Battery icon flashes then black screen. Boot to download mode.. Push up arrow, black screen. Computer does not register device connected.
Sent from my SGH-I997 using xda app-developers app
Click to expand...
Click to collapse
It's hard to give any suggestions with this little information. More information would be useful. A lot more information would be more helpful.
creepyncrawly said:
It's hard to give any suggestions with this little information. More information would be useful. A lot more information would be more helpful.
Click to expand...
Click to collapse
When I plug then phone in (automatically turns on when plugged in, power button is broken), the battery logo and hardware buttons flash erratically for up to a minute then nothing at all. I've tried different batteries and different cords. The only thing that seems to bring it back to life is letting the phone and battery sit unplugged for 2 weeks up to a month and trying again, but it's very hit or miss. This only seems to happen when the battery completely drains.
jvick920 said:
When I plug then phone in (automatically turns on when plugged in, power button is broken), the battery logo and hardware buttons flash erratically for up to a minute then nothing at all. I've tried different batteries and different cords. The only thing that seems to bring it back to life is letting the phone and battery sit unplugged for 2 weeks up to a month and trying again, but it's very hit or miss. This only seems to happen when the battery completely drains.
Click to expand...
Click to collapse
What phone do you have... the AT&T SGH-I777 does not have hardware buttons, but maybe you mean the capacitive buttons which are part of the display? Your previous post was sent from an Infuse? If it's not an I777 then you need a different forum.
If the phone that has the problem is an SGH-I777, then... what firmware is/was it running? Is it rooted? Is USB debugging turned on? Have you been able to boot into download mode since your first post? How long was the power button broken before this problem first manifested?
I think you need to get into download mode and flash stock firmware.
You also may need to see if you can do something about the broken power button, since that may be involved in the problem. That would mean either taking the phone apart and trying to mechanically clean the button or move/press/activate it a lot to get the dirt out so that the problem clears itself, or it may mean getting it replaced.
creepyncrawly said:
What phone do you have... the AT&T SGH-I777 does not have hardware buttons, but maybe you mean the capacitive buttons which are part of the display? Your previous post was sent from an Infuse? If it's not an I777 then you need a different forum.
If the phone that has the problem is an SGH-I777, then... what firmware is/was it running? Is it rooted? Is USB debugging turned on? Have you been able to boot into download mode since your first post? How long was the power button broken before this problem first manifested?
I think you need to get into download mode and flash stock firmware.
You also may need to see if you can do something about the broken power button, since that may be involved in the problem. That would mean either taking the phone apart and trying to mechanically clean the button or move/press/activate it a lot to get the dirt out so that the problem clears itself, or it may mean getting it replaced.
Click to expand...
Click to collapse
It is the I777, capacitive buttons is what I meant.. I apologize, I'm still fairly new with terminology.. Yes, I have an Infuse also, it's my backup phone because I can't get the s2 to charge. It is rooted and flashed, running 4.2.2 (Avatar ROM)
The problem is, it isn't holding enough of a charge to do anything. Aside from the previously stated issue, it will go into download mode, but the screen will only stay on for maybe 5 seconds max. The power button has been broken about 6 months before this issue arose. This only started happening about a month ago when I let the battery discharge completely. To test my theory that it's a battery/charging issue, I got a backup battery (which allowed the phone to work again) and I allowed that one to discharge completely. Now I'm having the same issue with both batteries. I was able to get the phone to power on once after letting the phone and battery sit disconnected for about 2 weeks.
jvick920 said:
It is the I777, capacitive buttons is what I meant.. I apologize, I'm still fairly new with terminology.. Yes, I have an Infuse also, it's my backup phone because I can't get the s2 to charge. It is rooted and flashed, running 4.2.2 (Avatar ROM)
The problem is, it isn't holding enough of a charge to do anything. Aside from the previously stated issue, it will go into download mode, but the screen will only stay on for maybe 5 seconds max. The power button has been broken about 6 months before this issue arose. This only started happening about a month ago when I let the battery discharge completely. To test my theory that it's a battery/charging issue, I got a backup battery (which allowed the phone to work again) and I allowed that one to discharge completely. Now I'm having the same issue with both batteries. I was able to get the phone to power on once after letting the phone and battery sit disconnected for about 2 weeks.
Click to expand...
Click to collapse
What firmware is/was it running?
Is it rooted?
Is USB debugging turned on?
Did it charge the second battery fully more than once?
How long did it operate with the second battery?
creepyncrawly said:
What firmware is/was it running?
Is it rooted?
Is USB debugging turned on?
Did it charge the second battery fully more than once?
How long did it operate with the second battery?
Click to expand...
Click to collapse
Firmware is CM 10.1, it is rooted, running AvatarROM. USB debugging and mock locations were turned on. It had no issue charging while it was working, it was after I allowed the batteries to die that I started having issues. Even on the second battery, it would continue operating as long as I kept it charged.
jvick920 said:
Firmware is CM 10.1, it is rooted, running AvatarROM. USB debugging and mock locations were turned on. It had no issue charging while it was working, it was after I allowed the batteries to die that I started having issues. Even on the second battery, it would continue operating as long as I kept it charged.
Click to expand...
Click to collapse
I have never used Cyanogen Mod or any of the other AOSP firmware, and I don't know how the firmware would affect this issue, if at all. But I suspect there may be some link.
I think what you need to do is to flash back to stock firmware, or perhaps use one of the stock plus root packages, and then a custom kernel, and then reload CM 10.1. So try this:
Pull the battery and leave it out. Open Odin3 on the desktop and then while holding down the volume buttons, plug in the usb cable. See if the phone will boot into download mode this way, and if Odin will recognize it. If so, then go ahead and flash the stock of your choosing. I think if it were me, I would flash 4.0.4 UCLL6 plus root.

Infinite battery loop

The phone seems to be stuck in an infinite battery loop.
1) With the battery in, not using the charger.
It first boots into a grey battery for a couple of seconds and then it gets to a green charging battery. I can hear a short vibration, and it boots again into the grey battery and then into the green one. The phone is stuck into that loop until the battery drains.
2) With the battery in and the USB cable plugged in.
The phone boots into the grey battery and then into the green one. It stays there forever. No vibration sound and no rebooting. It keeps charging until hitting the 100% message.
Now, a few days ago I was able to hold the power button down and the phone would reboot normally. I could use the phone for a few hours until, all of a sudden, it would turn off and boot again into the battery loop. Holding the power button and rebooting normally would ONLY work with the USB cable in. If I unplugged the USB cable, the phone would be stuck in the battery loop.
A couple of days ago, I noticed that when I managed to reboot normally and pressed the power button, the phone would ask me if I wanted to restart, and a couple of seconds after that it would reboot into the battery loop.
Now holding the power button down with the USB cable in won't do the trick anymore. It is as if the power button is disabled or something.
Is there a fix for this? If I hold the volume button down I can get to the download mode (Odin Mode). THe info I get is as follows:
Product name: SGH-i777
Custom Binary Download: Yes (1 counts)
Current Binary: Samsung Official
The only way to get out of the download mode is by removing the battery.
Any ideas as to what's going on here?
thanks!
Looks like the culprit is the power button.
I flashed the newest Samsung firmware using Odin in download mode, and I could reboot normally after flashing. I'm using Auto Screen On/Off to wake up the phone, and it does a good job. The Power Off Button apps didn't seem to work, though.
Thing is, if I power off the phone or restart it, it goes into the battery loop again, and the only way to reboot normally that I know is by flashing the stock firmware again.
Is there any easier, faster way to reboot normally with a broken power button?
thanks!
cirerita said:
Is there any easier, faster way to reboot normally with a broken power button?
Click to expand...
Click to collapse
You could try this (it's another power button app https://play.google.com/store/apps/details?id=com.painless.pc). I've used it in the past with great success.
If it doesn't work for you you're currently not rooted - I know your stats show you've downloaded a custom binary, so you shouldn't have any problems.
Post back if you do, and also give us more information regarding which rom you're on.
Thanks, that app is really useful.
I used a custom rom a while ago but then I switched back to stock. I'm using the latest one from Kies (4.1.2, I think to recall). I use Framaroot to root the phone so I can use some apps I like.
Phone still reboots randomly. Maybe I need to clean the cache. Is there an app for doing that while running Android?
Alternatively, is there a kernel/rom that allows me to reboot normally, bypassing the battery loop? The Odin download mode takes too long because I have to flash the stock firmware, and the stock Recovery mode is useless to me because my power button is broken.
IS it possible to access Recovery mode with a broken power button?
thanks!
Sure, but the app I linked allows you to boot to recovery also.
A good custom kernel for a rooted 4.1.2 would be AJK 4.9, the No Swap version I believe. You'd be better off reading the op in the AJK thread.
Thanks, I'll take a good look at the AJK thread. Is it any better than the Siyah kernel?
Problem is, if the phone reboots randomly, then I'm stuck in the battery loop again and I need to flash the stock firmware yet again to be able to reboot normally and bypass the battery loop. I would need some sort of custom boot which I could access pressing the volume button, and which would allow me to reboot bypassing the battery loop.
SteveMurphy said:
Sure, but the app I linked allows you to boot to recovery also.
A good custom kernel for a rooted 4.1.2 would be AJK 4.9, the No Swap version I believe. You'd be better off reading the op in the AJK thread.
Click to expand...
Click to collapse
Just flashed AJK 4.9 and no more random rebootings as of now... Plus, if I reboot manually, it does not get into the dreaded battery loop. So far so good. Thanks a lot for the tip.
cirerita said:
Thanks, I'll take a good look at the AJK thread. Is it any better than the Siyah kernel?
Problem is, if the phone reboots randomly, then I'm stuck in the battery loop again and I need to flash the stock firmware yet again to be able to reboot normally and bypass the battery loop. I would need some sort of custom boot which I could access pressing the volume button, and which would allow me to reboot bypassing the battery loop.
Click to expand...
Click to collapse
AJK's Kernel is based off Siyah.

Moto Z XT1650-05 Do not charge or sim signal.

Hello friends, I come to report here a problem I'm having with my device.
It is not charging my battery, I thought it was a problem in the battery itself, I made the replacement for an original, but the problem was not solved. the device uses all the battery power, it stays at 0% and it does not charge, besides, it recognizes my SIM card, but there is no signal from the operator to make calls or use the 4G network, I did a lot of research I saw that it was a problem related to Software, regarding the CQA test, I saw several tutorials, where none succeeded, lastly, I would like to install a custom rom to see if the problem would be solved, but I went to do the bootloader unlock process, but when Fastboot displays the code and I enter the site of the motorola, it returns me with an error that I can not unlock the bootloader of my cell phone, and I need to unlock to be able to customize the android.
follows a video showing what is happening with my device.
https://www.youtube.com/watch?v=17roum_XlzQ
sorry if my text contains errors, I'm from Brazil and I used the translator to write
Thank you if anyone can help me because I have the device stopped because of this.
Thank you!
Hi, had the same issue. What helped me was connecting
power cable, going to bootloader, from there navigate to recovery. When it boots to recovery, regardless if there is any, leave it for some time. After about 5-10 minutes try rebooting, and it might picked up some charge, then it should charge as normally but very slowly, cellular connection also appeared.
Last time when my phone went to 0% and after going through this procedure my phone was at 17% after charging in recovery mode but didn't charge in normal mode after reboot. I also needed to toggle some setting regarding CQA in bootloader menu. Then everything went back to normal.
I will do this procedure to see if it solves my problem, remembering that my battery is in 0% and with it connected in the device it is only displaying the lightning, informing that the battery is without load.
what settings did you make regarding the CQA?
vNo said:
Hi, had the same issue. What helped me was connecting
power cable, going to bootloader, from there navigate to recovery. When it boots to recovery, regardless if there is any, leave it for some time. After about 5-10 minutes try rebooting, and it might picked up some charge, then it should charge as normally but very slowly, cellular connection also appeared.
Last time when my phone went to 0% and after going through this procedure my phone was at 17% after charging in recovery mode but didn't charge in normal mode after reboot. I also needed to toggle some setting regarding CQA in bootloader menu. Then everything went back to normal.
Click to expand...
Click to collapse
My device does not hold 5 seconds on bootloader because my battery is at 0% I believe the power supplied by the cable in the charger is not enough to keep it powered on. and now?
Original charger is definitely more than enough to keep phone on in bootloader mode. Try to make sure that usb C connection is dust and grease free.
Regarding CQA mode setting I can't remember exactly, but that is second thing.
Maybe even 5 seconds in bootloader should be just fine to navigate to recovery.
I wish you good luck, i was almost desperate when it firstly happened to me.
i had the same problem. after lot of trial and error i found a solution.
connect to power source (wall adaptor/modo battery mod.) get into bootloader menu and wait for 5 mins pressing vol up or down frequently.
then select reboot to recovery. on red triangle screen holding power button press and release volume up button one time. you will get into android stock recovery
select option wipe cache partition. and select yes when asked.
keep charging the device upto half hour in recovery mode and then select option reboot to bootloader.
after bootloader menu appears scroll down to BPTools and select it.
Your Phone will reboot and you will get Network and Your Phone will also charge normally.
Warning: Do not let your phone discharge to 0% or you might have to perform all above steps again.
This method worked for me as well. I recently replaced the battery on my Moto z force droid but couldn't get it to charge and signal was gone, after trying several things the Bp tools worked great, thanks dude.

Categories

Resources