Hi guys!
I just unlocked my bootloader and installed CWM recovery.
I want to install epinter's JB rom.
What are the steps?
I do this:
-wipe cache
-factory reset ---> there when it is going to finish it goes to the top recovery screen and does not say that it finished successfully
after these steps I tried to install the zip but it said:
-finding update package
-opening update package
-installing update...
symlink: some symlinks failed
E:Error in /sdcard/cm....zip
(Status 7)
Installation aborted.
What should I do?
try with redownloading rom!!
Officially corp via w8
I rebooted into cwm and worked. Now I am stuck at the Moto logo.
Can someone tell me the steps? What to wipe and what to format before flashing the zip??
solved!
petran_7 said:
solved!
Click to expand...
Click to collapse
how did you solve the stuck at moto screen
It usually happens when a step is overlooked. Can be resolved by retracing your steps. It happened to me once when I forgot to wipe the dalvik cache.
Sent from my MB860 using xda app-developers app
Gauu said:
how did you solve the stuck at moto screen
Click to expand...
Click to collapse
It can be stuck due to multiple reasons.
Perform a clean wipe/erase
Enter into fastboot by holding vol down and push power button
Release volume down and Press volume up to confirm fastboot selection.
Connect Phone with your microUSB cable to PC
Open command prompt and navigate to directory where you copied fastboot
Type these commands
fastboot devices (should display device id if your phone has successfully entered into fastboot mode)
fastboot -w (erases userdata and cache)
fastboot erase system
fastboot erase boot
fastboot erase recovery
fastboot erase webtop
fastboot erase preinstall
fastboot reboot (make sure you get into fastboot again)
fastboot flash recovery recovery.img (place desired recovery - preferably CWM 5.0.2.7/romracer's)
Boot into recovery and flash the desired ROM from sdcard.
Hope this helps
---------- Post added at 02:04 PM ---------- Previous post was at 01:54 PM ----------
Gauu said:
how did you solve the stuck at moto screen
Click to expand...
Click to collapse
It can be stuck due to multiple reasons.
Perform a clean wipe/erase
Enter into fastboot by holding vol down and push power button
Release volume down and Press volume up to confirm fastboot selection.
Connect Phone with your microUSB cable to PC
Open command prompt and navigate to directory where you copied fastboot
Type these commands
fastboot devices (should display device id if your phone has successfully entered into fastboot mode)
fastboot -w (erases userdata and cache)
fastboot erase system
fastboot erase boot
fastboot erase recovery
fastboot erase webtop
fastboot erase preinstall
fastboot reboot (make sure you get into fastboot again)
fastboot flash recovery recovery.img (place desired recovery - preferably CWM 5.0.2.7/romracer's)
Boot into recovery and flash the desired ROM from sdcard.
Hope this helps
Dear Member,
I'm new to rooring and flashing custom ROMS...
i have a folio 100 and after a lot of googling and hardwork i finally managed to root my device on windows XP.. then i tried to install Jelly Bean / CM10 (4.1.1) Alpha 2 - 27.09.2012 from http://forum.xda-developers.com/showthread.php?t=1864774 and followed the instructions.
initially when i typed fastboot devices i was getting "? fastboot" and rest of the commands returned 0x2 error.
then i treid
fastboot -i 0x955 erase userdata
fastboot -i 0x955 erase system
fastboot -i 0x955 erase cache
fastboot -i 0x955 erase linux
fastboot -i 0x955 erase recovery
till now everything worked like a charm but when i tried to run the last command
fastboot -i 0x955 flash recovery recovery-cwm-6.0.1.4.img
i'm getting error message "unable to load recoveryxxxx.img"
now i treid to reboot the device and its saying "magic value mismatch" please help me out..
Nonlxpe Menteur
leaderrocks said:
Dear Member,
I'm new to rooring and flashing custom ROMS...
i have a folio 100 and after a lot of googling and hardwork i finally managed to root my device on windows XP.. then i tried to install Jelly Bean / CM10 (4.1.1) Alpha 2 - 27.09.2012 from http://forum.xda-developers.com/showthread.php?t=1864774 and followed the instructions.
initially when i typed fastboot devices i was getting "? fastboot" and rest of the commands returned 0x2 error.
then i treid
fastboot -i 0x955 erase userdata
fastboot -i 0x955 erase system
fastboot -i 0x955 erase cache
fastboot -i 0x955 erase linux
fastboot -i 0x955 erase recovery
till now everything worked like a charm but when i tried to run the last command
fastboot -i 0x955 flash recovery recovery-cwm-6.0.1.4.img
i'm getting error message "unable to load recoveryxxxx.img"
now i treid to reboot the device and its saying "magic value mismatch" please help me out..
Click to expand...
Click to collapse
First, download the latest & most stable ROM (at the moment), including the ROM, GAPPS, recovery-cwm-CM10-A3.img & formatsd.zip
http://forum.xda-developers.com/showthread.php?t=1864774
Actually, you just need to flash the recovery through fastboot, other else can done in the recovery.
1. Copy all the ROM, GAPPS & formatsd.zip into your memory card. Then insert it into your Folio.
2. Run command prompt, make sure your tablet is connected with your PC in fastboot mode.
To erase existing/stock recovery. In command prompt, go into the fastboot program folder and type the following commands
Code:
fastboot erase recovery
3. Copy the CWM Recovery into your fastboot adb folder.
To flash CWM Recovery
Code:
fastboot flash recovery recovery-cwm-CM10-A3.img
fastboot reboot
4. Enter Recovery. Before you begin, wipe everything (except external_sd) in the CWM Recovery, after wiped, you can install the 3 zip files one by one. After finish, just reboot system.
Full procedure also stated in the link I provided, please scroll down.
Hope that helps you.
So did above solution help? I had a similar issue, and I resolved it by just booting the recovery image from fastboot, i.e.
Code:
fastboot boot recovery.img
Once you get into recovery you can flash an image which will in most cases flash a recovery image along with it. If not, you can try to flash the recovery image again once you've done a full wipe from the booted recovery.
OK
i tried to put the 2.6 TWRP on i think it was for the incorrect bootloader (10.6.1.8) so its asking for a password and can't mount anything. bootloader freezes whenever i do anything through fastboot .Adb can see the device in twrp .
PLS help !!!
Any one ...any help
What i did to fix this :
use windows 7 not 8.1 install drivers
I used "Minimal ADB and Fastboot" --- google it
and using part of http://forum.xda-developers.com/showpost.php?p=44244313&postcount=12
fastboot erase system
fastboot erase recovery
fastboot erase userdata
fastboot erase boot
fastboot erase misc
fastboot erase cache
fastboot -i 0x0B05 flash system c:\adb\blob --------- gives me an error uploading the blob !!!!!
fastboot -i 0x0B05 reboot ----did not respond --- have to use hardware buttons
When i restart i didn't have recovery at this point just boot in to fastboot menu (i thought i killed my asus totally ))
what i did after :
I FLASH BOOTLOADER ON THE LINK
https://www.androidfilehost.com/?fid=23060877490002899 (unzipp it and there is blob<--- i copy it in the abd/fastboot folder)
fastboot flash boot blob
reboot and go in to recovery to confirm that is Hairybean TWRP 2.5 (no enter your password any more ihaaa)
i download twrp_tf201t_kang_2.8.5.1_signed.zip (unzipp it and there is boot.blob<--- i copy it in the abd/fastboot folder) from ... https://www.androidfilehost.com/?fid=95916177934539154
and
fastboot erase recovery
fastboot flash recovery boot.blob
( I found that.... fastboot flash recovery xxxxxxxx ........... works ONLY if you do ..... fastboot erase recovery ......... first !!!!! i tryed flashing even my original twrp 2.4.4 and its asked me for the password again ..i try so many recovery version.....JB or ICS ...TWRP and CWM you name it ..just this and Hairybean TWRP 2.5 didn't asked for a password )
After ... fastboot flash recovery boot.blob ..... fastboot reboot .....worked ---- restart in to recovery ---- and i did not have that annoying "enter your password" msg any more !!!
than using part from :http://forum.xda-developers.com/transformer-prime/development/rom-katkiss-5-1-tf201-22-t3080892
Go to twrp/wipe/format data then type yes
It takes about 70 minutes to format
Make sure that your battery is full
Do Not interrupt format(if you do, it will brick)
After it's done go to Wipe//Advanced Wipe//Select Data
Tap “Repair or Change File System”//”Change File System//F2FS
Swipe to Change
Wipe dalvik cache, system, cache, data, internal storage
reboot in to twrp
At that point MY pc can see my tf201 internal storage in TWRP no problem so i just copy zips in there ....... didn't use sd card
Flash KatKiss-5.1.1_TF201_030.zip
Flash Supersu.zipin
Flash Gapps.zip
Reboot
Rom http://forum.xda-developers.com/devd...9236#downloads
SuperSu v2.46 http://download.chainfire.eu/supersu
Minimal Gapps https://www.androidfilehost.com/?fid=95916177934550851
I was trying to install TWRP on my NX529J.
"Adb reboot bootloader command" is working but when i try to install TWRP with command "Fastboot flash recovery recovery.img", it dosent work.
It shows "waiting for devices"
Tried " fastboot devices" NO device there
I tried updating all drivers installed fastboot drivers and zte drivers but still no device found.
In developer settings OEM unlock, USB debugging is on.
and adb mode is also on with *#7678#.
Plz Help.
teji007 said:
I was trying to install TWRP on my NX529J.
"Adb reboot bootloader command" is working but when i try to install TWRP with command "Fastboot flash recovery recovery.img", it dosent work.
It shows "waiting for devices"
Tried " fastboot devices" NO device there
I tried updating all drivers installed fastboot drivers and zte drivers but still no device found.
In developer settings OEM unlock, USB debugging is on.
and adb mode is also on with *#7678#.
Plz Help.
Click to expand...
Click to collapse
sudo fastboot -i 0x19d2 boot recovery.img
sudo command not recognized in windows
anish.mvj said:
sudo fastboot -i 0x19d2 boot recovery.img
Click to expand...
Click to collapse
Sir.
i tried this command also but windows didnt recognized sudo command.
Plz any other way?
teji007 said:
Sir.
i tried this command also but windows didnt recognized sudo command.
Plz any other way?
Click to expand...
Click to collapse
That is ubuntu command.
For windows run CMD as administrator and then run
fastboot -i 0x19d2 boot recovery.img
Thanks and a little more help
anish.mvj said:
That is ubuntu command.
For windows run CMD as administrator and then run
fastboot -i 0x19d2 boot recovery.img
Click to expand...
Click to collapse
Thank you very much
Sir i upgraded my nx529j to 6.0.1, is there anyway to root it or downgrade to 5.1.1?
teji007 said:
Thank you very much
Sir i upgraded my nx529j to 6.0.1, is there anyway to root it or downgrade to 5.1.1?
Click to expand...
Click to collapse
Yes its possible.
Rooting is absolutely not required.
Follow the steps below
1. Download the latest 1.40 firmware from nubia india website support page. [Direct Link]
2. Then open the zip file and extract the recovery.img to local folder. Transfer the zip as it is to SD card
3. Goto fastboot/bootloader and run following
Code:
fastboot -i 0x19d2 flash recovery recovery.img
4. Then select reboot to recovery from bootloader menu.
5. Select wipe all application
6. Then install the downloaded zip [i hope you have already know how to do that]
It will automatically reboot.
That's it you are done downgrading
Failed
anish.mvj said:
Yes its possible.
Rooting is absolutely not required.
Follow the steps below
1. Download the latest 1.40 firmware from nubia india website support page. [Direct Link]
2. Then open the zip file and extract the recovery.img to local folder. Transfer the zip as it is to SD card
3. Goto fastboot/bootloader and run following
Code:
fastboot -i 0x19d2 flash recovery recovery.img
4. Then select reboot to recovery from bootloader menu.
5. Select wipe all application
6. Then install the downloaded zip [i hope you have already know how to do that]
It will automatically reboot.
That's it you are done downgrading
Click to expand...
Click to collapse
It says wiping failed(please wipe again or do it after reboot) everytime.
and nothing is working even app wipe or data wipe, only cache wiped works and choose from phone storage is also n ot working and sd card is also being not dtetected.
even in TWRP
anish.mvj said:
Yes its possible.
Rooting is absolutely not required.
Follow the steps below
1. Download the latest 1.40 firmware from nubia india website support page. [Direct Link]
2. Then open the zip file and extract the recovery.img to local folder. Transfer the zip as it is to SD card
3. Goto fastboot/bootloader and run following
Code:
fastboot -i 0x19d2 flash recovery recovery.img
4. Then select reboot to recovery from bootloader menu.
5. Select wipe all application
6. Then install the downloaded zip [i hope you have already know how to do that]
It will automatically reboot.
That's it you are done downgrading
Click to expand...
Click to collapse
I insatlled TWRP recovery, even in that wiping is not working. is there any way to install custom roms without rooting.
i actully installed official 6.0.1 update from their official nubia site and installed it.
teji007 said:
I insatlled TWRP recovery, even in that wiping is not working. is there any way to install custom roms without rooting.
i actully installed official 6.0.1 update from their official nubia site and installed it.
Click to expand...
Click to collapse
Dude please be clear what you want to do? Stock rom or custom?
Custom
anish.mvj said:
Dude please be clear what you want to do? Stock rom or custom?
Click to expand...
Click to collapse
.
Sir i want custom Rom. and sir now i am bricked
teji007 said:
.
Sir i want custom Rom. and sir now i am bricked
Click to expand...
Click to collapse
what do you mean by your are bricked?
If you want custom rom
Goto TWRP wipe everything
if above fails then try out following
Option 1:
Goto Bootloader mode and from that menu goto emergency recovery. Try wiping from there if successful, flash a stock rom [Kitkat] and boot to system. After first boot goto settings and reset factory settings. Then goto TWRP and wipe, it will wipe for sure. then you can install any custom rom
Option 2:
Download the oldest firmware from the nubia site [1.37] and flash recovery from there [extract the recovery from zip and flash it in bootloader]. Then use
Code:
fastboot -i 0x19d2 boot TWRP.img
to boot to twrp, don't flash it. Then goto advanced and select adb sideload. swipe to start sideload. after that open the zip you downloaded and got to
Code:
/META-INF/com/google/android/
and open updater-script with any of the text file. Delete the first line and save. update the zip.
open cmd from that folder where zip is located. then type
Code:
adb sideload NX529J_Z69_EN_NSXPK1JD00K137.zip
and press enter. let it complete and then reboot. it should boot to factory firmware. Follow the same procedure to factory reset from settings menu then flash TWRP and flash custom rom
Use the above steps. If all fails then revert back.
Thanks going to try
anish.mvj said:
what do you mean by your are bricked?
If you want custom rom
Goto TWRP wipe everything
if above fails then try out following
Option 1:
Goto Bootloader mode and from that menu goto emergency recovery. Try wiping from there if successful, flash a stock rom [Kitkat] and boot to system. After first boot goto settings and reset factory settings. Then goto TWRP and wipe, it will wipe for sure. then you can install any custom rom
Option 2:
Download the oldest firmware from the nubia site [1.37] and flash recovery from there [extract the recovery from zip and flash it in bootloader]. Then use
Code:
fastboot -i 0x19d2 boot TWRP.img
to boot to twrp, don't flash it. Then goto advanced and select adb sideload. swipe to start sideload. after that open the zip you downloaded and got to
Code:
/META-INF/com/google/android/
and open updater-script with any of the text file. Delete the first line and save. update the zip.
open cmd from that folder where zip is located. then type
Code:
adb sideload NX529J_Z69_EN_NSXPK1JD00K137.zip
and press enter. let it complete and then reboot. it should boot to factory firmware. Follow the same procedure to factory reset from settings menu then flash TWRP and flash custom rom
Use the above steps. If all fails then revert back.
Click to expand...
Click to collapse
Thank you very much sir.
Can i contact you by any other means? whatsapp or any other
teji007 said:
Thank you very much sir.
Can i contact you by any other means? whatsapp or any other
Click to expand...
Click to collapse
Check your private message
adb sideload not working
anish.mvj said:
what do you mean by your are bricked?
If you want custom rom
Goto TWRP wipe everything
if above fails then try out following
Option 1:
Goto Bootloader mode and from that menu goto emergency recovery. Try wiping from there if successful, flash a stock rom [Kitkat] and boot to system. After first boot goto settings and reset factory settings. Then goto TWRP and wipe, it will wipe for sure. then you can install any custom rom
Option 2:
Download the oldest firmware from the nubia site [1.37] and flash recovery from there [extract the recovery from zip and flash it in bootloader]. Then use
Code:
fastboot -i 0x19d2 boot TWRP.img
to boot to twrp, don't flash it. Then goto advanced and select adb sideload. swipe to start sideload. after that open the zip you downloaded and got to
Code:
/META-INF/com/google/android/
and open updater-script with any of the text file. Delete the first line and save. update the zip.
open cmd from that folder where zip is located. then type
Code:
adb sideload NX529J_Z69_EN_NSXPK1JD00K137.zip
and press enter. let it complete and then reboot. it should boot to factory firmware. Follow the same procedure to factory reset from settings menu then flash TWRP and flash custom rom
Use the above steps. If all fails then revert back.
Click to expand...
Click to collapse
Sir, its been 5 mins its "starting ADB sideload feature" but nothing
adb sideload failed
anish.mvj said:
Check your private message
Click to expand...
Click to collapse
Sir ,
ADB sideload failed
teji007 said:
Sir ,
ADB sideload failed
Click to expand...
Click to collapse
Hi how did your device visible in fastboot devices?
I installed adb drivers and all but my device is not listed in fastboot devices..
It is being listed in adb devices but not on fastboot devices. Can you help me with this?
---------- Post added at 08:51 PM ---------- Previous post was at 08:50 PM ----------
teji007 said:
I was trying to install TWRP on my NX529J.
"Adb reboot bootloader command" is working but when i try to install TWRP with command "Fastboot flash recovery recovery.img", it dosent work.
It shows "waiting for devices"
Tried " fastboot devices" NO device there
I tried updating all drivers installed fastboot drivers and zte drivers but still no device found.
In developer settings OEM unlock, USB debugging is on.
and adb mode is also on with *#7678#.
Plz Help.
Click to expand...
Click to collapse
Hi how did your device visible in fastboot devices?
I installed adb drivers and all but my device is not listed in fastboot devices..
It is being listed in adb devices but not on fastboot devices. Can you help me with this?
Hello there! I unlock my bootloader and install twrp in my redmi 6 pro(sakura). Then i install havoc os and it was running completely fine . Then i flash camera to api & dm verity by twrp. After flashing and rebooting, my phone stuck on havoc animation after redmi sign . Then i wipe everything and then i flash lineage os and it also stuck on lineage animation. Whichever os i flash, it stuck on that Animation. It's non root device. Still it stuck on os animation. How to solve? Please Help
connect to pc via usb
open cmd window in adb and fastboot folder
reboot your device to fastboot mode using hardware keys
type fastboot devices to test connection
then download your stock rom from the internet
extract it
enterthe firmware file
copy recovery.img system.img cache.img userdata.img and boot.img
paste them in the adb folder
now in cmd window type
fastboot erase boot
fastboot flash boot boot.img
fastboot erase recovery
fastboot flash recovery recovery.img
fastboot erase userdata
fastboot flash userdata userdata.img
fastboot erase cache
fastboot flash cache cache.img
fastboot erase system
fastboot flash system system.img
and you're all done, your phone should be able to start now
brother i am very new . adb and fastboot folder means ? is it platform tools folder
brother i am very new .adb and fastboot folder means ? is it platform tools folder ?
narwhhal27 said:
connect to pc via usb
open cmd window in adb and fastboot folder
reboot your device to fastboot mode using hardware keys
type fastboot devices to test connection
then download your stock rom from the internet
extract it..
enterthe firmware file
copy recovery.img system.img cache.img userdata.img and boot.img
paste them in the adb folder
now in cmd window type
fastboot erase boot
fastboot flash boot boot.img
fastboot erase recovery
fastboot flash recovery recovery.img
fastboot erase userdata
fastboot flash userdata userdata.img
fastboot erase cache
fastboot flash cache cache.img
fastboot erase system
fastboot flash system system.img
and you're all done, your phone should be able to start now
Click to expand...
Click to collapse