Related
So I'm a total n00b at unlocking phones but I was trying to unlock my alltel 6800 and after running the program and following the steps I'm stuck on the screen that is red/green/blue/white that shows the rom info and says USB at the bottom when plugged into the pc. I tried a hard boot/soft etc. and can't find a solution. Also activesync is not recoginizing it. Thanks much for any help.
i believe you have to flash it with a new rom/radio.
download the the newest radio. connect your phone via usb. your screen should be in the tricolor (2.40spl) at this point. run the radio flash.
Download a new rom. do the same as above.
to get to tricolor screen (hold power + camera + press soft reset)
Yeah i'm thinking I might have to load it from the SD card but I can't find my stinkin adapter so I can format the SD card. Activesync is not recognizing my phone at all.
=I'm stuck on the screen that is red/green/blue/white that shows the rom info and says USB at the bottom when plugged into the pc.
Click to expand...
Click to collapse
it IS recognizing the phone being plugged in if it says USB at the bottom, so just flash a new rom/radio and you should be good.
HOLD, Give a little more info please
wilmheath said:
Yeah i'm thinking I might have to load it from the SD card but I can't find my stinkin adapter so I can format the SD card. Activesync is not recognizing my phone at all.
Click to expand...
Click to collapse
OK, before it is bricked, tell us the numbers on the rainbow screen, then if it is 1.6 then run the 2.40 olipro, then new ROM, then radio. It is not broken yet, activesync does not like it when the unit is in bootloader mode so it will not show it, but the RUU will work if you just go forward with it and when done it will get you out of bootloader. If you get confused and lost then being an alltel unit you can put the 1.6 bootloader back on, run the stock RUU from utstar.com, bring it back stock and start again.
I got it fixed and installed the sprint firmware but silly me let it run through the setup and now it's trying to use the spring network. Sometimes I wish i could punch myself in the face..
Ok so i got no2chem up and running great but I still can't actually dial out. When i dial it says i'm not allowed to etc after a few rings. Is there some way to change back to the alltel network?
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
Click to expand...
Click to collapse
First of all, you don't relock your phone...you leave 2.4-olipro on it because it's required to boot your phone with this rom on it.
Second, go into activesync settings and make sure usb is enabled in the connections.
get back to Alltel,,,,
wilmheath said:
ok now i'm running titan 3.35 but can no longer get active sync which is required to relock the phone. I've tried everything but activesync does not want to work anymore. Any ideas?
Click to expand...
Click to collapse
You will need to load up the PRL and then do IOTA.
madman34 said:
You will need to load up the PRL and then do IOTA.
Click to expand...
Click to collapse
I'm sorry but i'm not familiar with those terms. I do have USB enabled on activesync though but it never detects it.
From reading other threads I assumed I had to relock it, then reload the alltel rom to get the radio working again. Is there another way?
I got the factory alltel rom back in and working but it's not letting me make calls still. Any ideas on how to fix this?
Well i got my phone working finally but now the data line is not working. It says I need a password now which I haven't needed before.
I installed an "updated" HTC Home Screen Plugin (obviously not for my phone model #) and now my phone is frozen. It will boot up but the home screen is frozen (i.e., non-responsive to any button presses). I attempted to re-flash the ROM using various ones I found for the NEON but all fail for the same reason.
Specifically, connection to ActiveSync is not possible (I connect via USB cable but ActiveSync doesn't recognize device). So what I do is put the phone in bootloader mode and then connect the USB cable. When I do this, the ROM upgrade program recognizes the phone and gets to the point where it shows the screen "Updating the ROM image on your PDA Phone.." and the phone shows a status bar at 0%. However, after a minute the computer screen says "ERROR [262]: UPDATE ERROR" and the phone is stile stuck at 0%.
My question is if there is any other way I can re-flash my NEON300? I've heard that it may be possible to but the nbh file on a FAT32 formatted card. I tried this by naming the nbh file to "TOUCHIMG.NBH" and "NEONIMG.NBH" but neither are recognized by the bootloader.
Thanks in advance for any assistance.
Try changing usb port or even re-installing activesync.
Alot pf people had the same problem on different devices but the cause should be the same.
for example, http://forum.xda-developers.com/showthread.php?t=298516
Let me know how you go.
Thanks for the advice Seth. I followed the link (install/re-install of ActiveSync didn't help) and I think I found my problem. Do I need to CID unlock the phone to install the ROM's? I ran the type 32 command from mtty and it shows a value of FF for the security lock.
Thanks
wangobyte said:
Thanks for the advice Seth. I followed the link (install/re-install of ActiveSync didn't help) and I think I found my problem. Do I need to CID unlock the phone to install the ROM's? I ran the type 32 command from mtty and it shows a value of FF for the security lock.
Thanks
Click to expand...
Click to collapse
You should have read the WIKI before flashing your device... http://wiki.xda-developers.com/index.php?pagename=Flashing Guide and here http://forum.xda-developers.com/showthread.php?t=355730
Hello all... tried to be a little geek and installed a custom Rom (Artemis V32 with radio 2.12.50.02_2) and that went ok. Then I copied an Android version to my sd card, and that went also ok.
Then I installed a bootloader so I could choose Android or WM, that went ok too.
But since then I had some regular crashes in Android and also with WM.
I decided to install a stock Rom (found via Usenet; Stock ROM (NLD) 1.72.172.0 met radio 2.07.51.22_2 en SPL-1.66.0000 ) and things went bad.
I have tried all kinds of things so resolve the issue:
- Put the stock rom on the sd card (formatted fat32, size 4gig) and renamed it to loeimg.nbh and started it up with the volume button down: no success
Message:
PB1100 HX-BC
SPL-1.66.0000 XE
MicroP(LED) 0x05
MicroP(TOUCH) 0x40
- Connected the hd2 with the original cable to my pc (Windows 7 Ultimate, and tried also WinXP SP3) and tried to install it via the .exe file from another stock rom I downloaded via the HTC website.No succes, the software starts-up, I can click yes, next, click yes again at "I completed the steps indicated above" and then I get the screen current information about your pda phone Image version does not mention any version at this point.
If I then click on update I get the screen that says from image version: to image version.
The from version is not filled in, so I think the fault has something to do with this.
After I clicknext 2 times I get the progress screen, but nothing happens then anymore. It keeps showing 0%
If anyone can help me out with this it would appreciate it a lot! And if you need any additional info, please let me know...
Thanks in advance,
Friendly greetings...
you no longer have hspl installed. It was removed by the (failed) stock rom from sd card flash attempt. In bootloader, see your spl ends .0000? that tells you hspl is gone.
Manually enter bootloader, connect usb, count to 20, run hspl2(right click run as administrator), choose 2.08.hspl.
When it completes, re enter bootlaoder (hold down vol as the phone restarts at 100%), wait for bootloader, wait for the word serial -> usb, run your rom flash over usb.
Thanks for the quick reply... as soon as I'm back home I'm going to try it out.. I'll post the result here..
something similiar happened to me some months ago..
should work
DN41
oh, and the reason the "from version" is blank is because that is read from the registry, but we put the phone in bootloader ourselves first so it can't see the registry. that's also why when you flash radios you see rom version info there. it can be ignored.
Do not forget to remove loeimg.nbh from your memory card before trying to flash under windows.
Thanks for the reactions... great to know I am not alone in this...
I performed the actions as described and I got the message "we hacked it"
I then tried to install a stock rom I downloaded but my phone turned off then at 11%
I have the idea that my battery is not loading anymore as I can't see the orange led burning when connected to the adapter/computer.
Ordered a new battery yesterday evening and will receive it normaly/hopefully today by mail. Then I will try again and share the results.
Thanks again all for the great support so far...
check the battery pins closely, hundreds of people have bent them poppng the battery out.
Ok, checked the connection of the pins.. these are ok I think.
Battery-led is still not showing went connected to usb.
So now my screen states the following:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CottulaHSPL 0x40
What rom can I now install? Only an official one?
I tried to download an official rom from the htc website (after inserting my serial), but when I run the
RUU_Leo_Vodafone_NL_1.72.172.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship it shows a message that the file is corrupt.. and this for about 6 times now...
I feel the noob-level is rising extremely now...
TitusV said:
What rom can I now install? Only an official one?
SPL-2.08.HSPL 8G XE
Click to expand...
Click to collapse
.hspl means hspl is installed so you can flash any rom.
I tried to download an official rom from the htc website (after inserting my serial), but when I run the
RUU_Leo_Vodafone_NL_1.72.172.0_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship it shows a message that the file is corrupt.. and this for about 6 times now...
(
Click to expand...
Click to collapse
all i can say is try another rom. just stick to usb flashing, protect hspl.
Hey guys,
Im a new member here
but been following through all the great posts here at XDA for a long time now.
I have been trying to unlock my HTC Radar for almost 2 days now but im unable to do so.
1. I tried using the ROMUpdateUtility from here : HSPL for HTC WP7 Second Generation
I got the Invalid Vender ID error and thus had to resort to the Gold Card Method. Made the Gold card from a 4GB MicroSD card , Bought the Y-cable ( 2 MALE and 1 Female type ) and also a Female-Female USB Gender Changer as per this post here :
[Noob-friendly] Goldcard SPL Downgrade Method; No Android-Phone and/or custom wires!
I Fixed it Accordingly but the Screen is stuck where it says *Enter USB Host Mode* .. i tried various combination of MicroSD card Readers and MicroSD card .. i have included a image of my configuration in this post
Can someone please help me...
Thank you In Advance
Did you successfully do the steps that required the gold card?
You have to put your phone in SPL mode in order to use RUU.
Do you have Windows Mobile Device Center installed?
Tried
I tried the RUU first by entering in SPL mode . Installed the Drivers and then i got an Invalid Vender id , so while using the gold card method i tried various Memory cards ( SD card : 2gb and 4gb ) and also Flash drives but the screen is always stuck in "Enter USB Host mode.."
Yeah me too, I followed every step in the instruction and I could not make it, my phone freezes at screen "Enter USB Host Mode" too
I tried HSPL, and I got this
Sorry I'm noob
phoenix_ said:
I tried the RUU first by entering in SPL mode . Installed the Drivers and then i got an Invalid Vender id , so while using the gold card method i tried various Memory cards ( SD card : 2gb and 4gb ) and also Flash drives but the screen is always stuck in "Enter USB Host mode.."
Click to expand...
Click to collapse
Hi, have you tried to swtich the phone and the card reader? In my opinion, the phone should be connected in the place of the card reader, and the card reader in the place of the phone. At the first time, at least for me, the process doesn't start inmediatly, I had to wait a couple of minutes the first time. I think that's not a problem with the gold card, if the gold card is not created properly the phone will be stuck at loading.
Greetings.
robuash said:
Hi, have you tried to swtich the phone and the card reader? In my opinion, the phone should be connected in the place of the card reader, and the card reader in the place of the phone. At the first time, at least for me, the process doesn't start inmediatly, I had to wait a couple of minutes the first time. I think that's not a problem with the gold card, if the gold card is not created properly the phone will be stuck at loading.
Greetings.
Click to expand...
Click to collapse
Thanks ! .. tried the thing you told. and no luck . The screen is stuck in *Enter USB Host Mode..*
Sorry but i think you are directly trying to hard spl...did u SPL 2.5 first?
cool.gautam said:
Sorry but i think you are directly trying to hard spl...did u SPL 2.5 first?
Click to expand...
Click to collapse
Do you mean the Gold card method of flashing SPL 2.05 !! yes i tried doing that and i failed because the process would not go above *Enter USB host mode..*
phoenix_ said:
Do you mean the Gold card method of flashing SPL 2.05 !! yes i tried doing that and i failed because the process would not go above *Enter USB host mode..*
Click to expand...
Click to collapse
Does your y-cable work properly?
Did you patch the proper image to the goldcard i.e the .nbh file?
im 100% sure i patched the correct OMEGIMG.nbh file cause the gold card tool showed that the process was success. I give up Been trying for 5 days now. I think time to quit and wait for some easy process to come along !
phoenix_ said:
im 100% sure i patched the correct OMEGIMG.nbh file cause the gold card tool showed that the process was success. I give up Been trying for 5 days now. I think time to quit and wait for some easy process to come along !
Click to expand...
Click to collapse
+1 same here....waiting for a method where no use of goldcard is there
I was stuck there for a while too. I ended up just rotating my y-cable with attachments until my radar recognized the goldcard and tried to load it. It's possible that your y-cable is not wired correctly also. I tried to buy one from a local store, and they told me that it wasn't designed in a way that would allow me to use it to make the goldcard, so I bought the recommended one from amazon.
WP7 noob here long time Android flasher/rooter.
What is the point of unlocking the Radar at this point as there doesn't seem to be ROM's available, or am I missing something? Are they coming?
Thanks for any replies.
There are currently 3 custom ROMS available in the development section.
Here
Phoenix Undone said:
There are currently 3 custom ROMS available in the development section.
Here
Click to expand...
Click to collapse
Thanks! I have no idea how I missed those!!
sorry
why my phone is always experiencing error 260 - Connection, I have to restart the phone and notebook, but still an error, there is a solution?
vandiska said:
why my phone is always experiencing error 260 - Connection, I have to restart the phone and notebook, but still an error, there is a solution?
Click to expand...
Click to collapse
try different usb port
vandiska said:
why my phone is always experiencing error 260 - Connection, I have to restart the phone and notebook, but still an error, there is a solution?
Click to expand...
Click to collapse
turn off your phone. hold volume up+down simultaneously & press power button, it should take you to SPL mode. then connect your phone to USB port. if you use windows 7, it would install the driver automatically. when installed, run the RUU.exe.
hope it helps
Fellow AT&T Titan owners:
I, like many of you, have been stuck on the 2.5 bootloader since September and have been working on many possible fixes posted in several forums. After no luck, I was resigned to put my Titan in the kitchen drawer and forget about it until a fix came out. 2 days ago I pulled the Titan out of the drawer to mess around with it because I was bored. I flashed a Titan TEST ROM uploaded by sh4d0w86 back in February 2012 HERE. I thought that it might help reset the settings in the phone. After flashing I checked the bootloader and it still said 2.5. :crying: DAMN!
I left the TEST ROM on the phone overnight and decided to flash stock AT&T ROM a few minutes ago, and I'll be a son-of-a-***** if it's not back to the stock 1.10 bootloader. :victory:
Maybe it was a fluke, I don't know, but I'm back to working with my Titan again. Check it out. Maybe it'll work for you too. :fingers-crossed:
EDIT: Just reflashed HSPL and custom ROM. I'm good-to-hook again.
I will try it asap, so u just flshed test rom, checked out SPL left it over night and tomorow flashed cingular 1.10 ROM? after that just regular procedure with SPL HSPL ? u flashed via USB cable all things, no Y cable?
I had to flash SPL via Y-cable per Cotulla's instructions in the HSPL Thread. But you may not need to let it sit overnight, I don't know. Maybe you can flash right away and get back to 1.10 or maybe not. It was just an unplanned event that had a brilliant result.
I hope it works for you too.
nikola92 said:
I will try it asap, so u just flshed test rom, checked out SPL left it over night and tomorow flashed cingular 1.10 ROM? after that just regular procedure with SPL HSPL ? u flashed via USB cable all things, no Y cable?
Click to expand...
Click to collapse
the thing is i had that ro flashed before and after that i flashe 1.10 and no change, so i want to try and make him sit over night
nikola92 said:
the thing is i had that ro flashed before and after that i flashe 1.10 and no change, so i want to try and make him sit over night
Click to expand...
Click to collapse
Please check out my post under debrand instructions under Windows Phone 7 development; you do not need your SPL to read 1.09 or 1.10 to successfully HSPL; it is imperative with whichever ROM you use for your device to read "HTC Titan x310e" not "HTC Titan P139100" following that first flash via Gold Card or everything that follows is mute. It is the 2nd step that will test your patience if you find yourself staring at "Entering USB Host Mode..." If following your flash of SPL205's NBH file you do not read on that screen, "Radio - OK", "Bootloader - OK", "Update Successful, UPDATE COMPLETED" your device will not HSPL on the next step. I recommend from the very beginning you rename the .NBH files to ETERDIAG (8 characters; no more) for steps 1 and 2 flashing via Gold Card. When you make your Gold Card use Quick Format; do not re-format your card following step 1; it is not necessary. I do recommend prior to copying the respective .NBH files to your Gold Card that they are renamed prior to copy. One more note..you may not have HSPL, but neither is your device a brick; SPL2.5.160015.3 is not the end of the world; though staring down a stock ROM really sucks after being spoiled royal.
berrywr said:
One more note..you may not have HSPL, but neither is your device a brick; SPL2.5.160015.3 is not the end of the world; though staring down a stock ROM really sucks after being spoiled royal.
Click to expand...
Click to collapse
This exactly. I was able to make calls and use the device as intended. Not like I wanted, but definitely as intended.
I was wanting to get back to stock SPL because I thought it was the only way to flash. The Titan forums are full of people that have been unable to attain HSPL due to the idea of being stuck on 2.5 bootloader was the cause. If your method works, that's awesome. As I said in my post, maybe it was a fluke but it seems so much easier to flash from stock. My primary device now is a One X so I may do some tinkering with my Titan soon. Regardless of how it turns out I appreciate your input into this.
R
But the now i when i write ETERDIAG i get flasing progres to start it comes nearly to end and then i get error 39 update terminated
Please Mr. berrywr Can help me ?
Pardon my English i'm an Italian Titan owner
I try your Plan B to debrand and have HSPL on my device because it doesn't go on using ETERIMG
I go on with ETERDIAG and everythings go in right way but ..
when i try to flash the renamed ETERDIAG.nbh copied from “SPL205” folder
my device don't FREEZE to Entering USB Host Mode but return on bootloader screen
i try after 15 or 20 minutes to move pointer with volume button and i'ts died no moove nothing change
only when i disconnect usb cable it's possible to move pointer up the bootloader menù
Now i try to change rom .
i start with european rom IMG_Eternity_HTC_Europe_1.09.401.02_Radio_16.23.02.09_A_16.24.00.23_Signed_ETERNITY_RELEASE
and i want follow your help and try with IMG_Eternity_Cingular_US_1.10.502.04_Radio_16.23.02.26_A_16.27.00.23_Signed_ETERNITY_RELEASE.nbh.
hope to read HSPL on my device please if someone have same problem PLEASE help me go on with my job
i write back if everythings go ok wih cingular rom but .. ok i write back
Best Regards Fabio Ducilli form Italy
This is my no means a flawless method; your problem is your memory card. I gave up on my microSD card and went to a PNY 4 gig thumb drive. There has been a common denominator throughout these threads in regards what memory card(s) work and don't work. This is the first device I have performed a Gold Card; it too is the first device I've ever own that does not have an expandable memory card slot. I have no way of knowing if renaming the .nbh file as "ETERIMG" or "ETERIMG.nbh" makes one bit of difference. I used "ETERDIAG" twice. In regards to flashing the SPL205 .nbh file...again if upon "Entering USB Host Mode" the device returns to the bootloader screen immediately, that's your memory card. If you think you're frozen in "Entering USB Host Mode" do not give up right away on your device. That said, if your device has been stuck at that screen for at least 30 minutes; it's reasonable to assume the flash failed. As I stated earlier...my wife's device HSPL was by the book; my device, I figured out it has nothing to do with the SPL being 1.09 or 1.10; it does have everything to do with your device being a "x310e". You cannot proceed to HSPL your device without your device being "x310e". I realize this is frustrating but there is a lot of trial and error as to what memory card or thumb drive ultimately works for you and in combination of what filename to use. If you begin "ETERDIAG" both steps are to be "ETERDIAG". My device and it being able to be flashed via USB thumb drive by no means implies this method will work for you and others, but it is proof as there are other threads that have been posted that confirm using a thumb drive does in fact, work. Please, keep us up to date; take care!
---------- Post added 31st December 2012 at 12:04 AM ---------- Previous post was 30th December 2012 at 11:34 PM ----------
What I know of an error 39 is related to USB hosting. Where are you in regards to flashing your device when the error occurs; USB Host Mode or Bootloader? You need Zune running if you're flashing through your computer; I have Windows 8 Professional installed on the laptop I used to flash both my Titans. I have Zune setup on all three of my HTC devices - 2 Titan I (Eternity) and 1 HD2 (Leo). I've had no problems whatsoever with my computer interfacing with my devices to date.
silentP said:
Fellow AT&T Titan owners:
I, like many of you, have been stuck on the 2.5 bootloader since September and have been working on many possible fixes posted in several forums. After no luck, I was resigned to put my Titan in the kitchen drawer and forget about it until a fix came out. 2 days ago I pulled the Titan out of the drawer to mess around with it because I was bored. I flashed a Titan TEST ROM uploaded by sh4d0w86 back in February 2012 HERE. I thought that it might help reset the settings in the phone. After flashing I checked the bootloader and it still said 2.5. :crying: DAMN!
I left the TEST ROM on the phone overnight and decided to flash stock AT&T ROM a few minutes ago, and I'll be a son-of-a-***** if it's not back to the stock 1.10 bootloader. :victory:
Maybe it was a fluke, I don't know, but I'm back to working with my Titan again. Check it out. Maybe it'll work for you too. :fingers-crossed:
EDIT: Just reflashed HSPL and custom ROM. I'm good-to-hook again.
Click to expand...
Click to collapse
It did not work for my titan...
ppgame said:
It did not work for my titan...
Click to expand...
Click to collapse
Sorry to hear that my friend. However, berrywr has been giving some excellent tuts for flashing. Thanks for giving it a shot though.
Specification of proble titan 1 hspl
berrywr said:
This is my no means a flawless method; your problem is your memory card. I gave up on my microSD card and went to a PNY 4 gig thumb drive. There has been a common denominator throughout these threads in regards what memory card(s) work and don't work. This is the first device I have performed a Gold Card; it too is the first device I've ever own that does not have an expandable memory card slot. I have no way of knowing if renaming the .nbh file as "ETERIMG" or "ETERIMG.nbh" makes one bit of difference. I used "ETERDIAG" twice. In regards to flashing the SPL205 .nbh file...again if upon "Entering USB Host Mode" the device returns to the bootloader screen immediately, that's your memory card. If you think you're frozen in "Entering USB Host Mode" do not give up right away on your device. That said, if your device has been stuck at that screen for at least 30 minutes; it's reasonable to assume the flash failed. As I stated earlier...my wife's device HSPL was by the book; my device, I figured out it has nothing to do with the SPL being 1.09 or 1.10; it does have everything to do with your device being a "x310e". You cannot proceed to HSPL your device without your device being "x310e". I realize this is frustrating but there is a lot of trial and error as to what memory card or thumb drive ultimately works for you and in combination of what filename to use. If you begin "ETERDIAG" both steps are to be "ETERDIAG". My device and it being able to be flashed via USB thumb drive by no means implies this method will work for you and others, but it is proof as there are other threads that have been posted that confirm using a thumb drive does in fact, work. Please, keep us up to date; take care!
---------- Post added 31st December 2012 at 12:04 AM ---------- Previous post was 30th December 2012 at 11:34 PM ----------
What I know of an error 39 is related to USB hosting. Where are you in regards to flashing your device when the error occurs; USB Host Mode or Bootloader? You need Zune running if you're flashing through your computer; I have Windows 8 Professional installed on the laptop I used to flash both my Titans. I have Zune setup on all three of my HTC devices - 2 Titan I (Eternity) and 1 HD2 (Leo). I've had no problems whatsoever with my computer interfacing with my devices to date.
Click to expand...
Click to collapse
nice to meet you sir
i'm talking about att titan 2.5 bootloader unlock
i need to flash my mobile with custom rom but
i follow the guide to do it
all ok
flash european rom 1.09.401.02 OKi check it and see the name changed to x310e
flash spl2.05 from dft and all ok that i flash it right
after i open DFT__HSPL_WP7SG1 and install like administrator the prog and it say me ENJOY but ...
i never find cotulla inside my bootloader after restart it
never see hspl word inside
can't install custom rom or application
can help me ? thanks Fabio from Italy
pardon my english
wileharley said:
nice to meet you sir
i'm talking about att titan 2.5 bootloader unlock
i need to flash my mobile with custom rom but
i follow the guide to do it
all ok
flash european rom 1.09.401.02 OKi check it and see the name changed to x310e
flash spl2.05 from dft and all ok that i flash it right
after i open DFT__HSPL_WP7SG1 and install like administrator the prog and it say me ENJOY but ...
i never find cotulla inside my bootloader after restart it
never see hspl word inside
can't install custom rom or application
can help me ? thanks Fabio from Italy
pardon my english
Click to expand...
Click to collapse
Okay...your device reads "x310e"; yes? When you re-setup your Gold Card to flash SPL205; your device should have underwent at least one restart and re-entered USB Host mode and you will be looking for the following words "RADIO - OK" and "BOOTLOADER - OK" and "Update Successful, UPDATE COMPLETED"...there would be nothing more on the screen. The next step is restart the device into Bootloader mode, ensure Zune is running on your computer and connect the device to your computer. You open the DFT HSPL folder (the other folder) and you will right click the application and run it as administrator. It should recognize the device and you will select HSPL. This last step takes only a matter of seconds and if successful you will see it almost immediately.
the thing is the name changed to x310e only in phone, but not in bootloader, the bootloader remains PI39100 like i have the case, everyting have flashed as u wrote, but nada in the end, it just wont change from PI39100 to x310e, i can flash euro rom only as ETERDIAG as ETERIMG i get kicked out to bootloader
nikola92 said:
the thing is the name changed to x310e only in phone, but not in bootloader, the bootloader remains PI39100 like i have the case, everyting have flashed as u wrote, but nada in the end, it just wont change from PI39100 to x310e, i can flash euro rom only as ETERDIAG as ETERIMG i get kicked out to bootloader
Click to expand...
Click to collapse
I restarted my device in Bootloader Mode; it reads as follows:
1st line: PI39100 - That's Papa India Three Nine One Zero Zero
2nd line: HSPL2.5.160015.3(137079)
3rd line: eMMC SND 15188MB
4th line: CotullaH(F:81, ID:1, V11,B:F8)
5th line: "Double Space"
6th line: Radio-17.5006.08.27 (This is the required radio for the Eburon WP7.8.8858 custom ROM).
In regards to your device reading x310e; that's good news! You're half way there. You need to have a successful second flash with your gold card with SPL205. Your device will automatically restart and return to Entering USB Host Mode prompt...it is this step you must have patience; it has to read Radio - OK, Bootloader - OK...Update Successful, UPDATE COMPLETED; it cannot be anything else or any combination other than these four.
Upon completion of the 2nd flash...SPL205's nbh file does your display indicate both Radio-OK and Bootloader-OK, Update Successful, UPDATE COMPLETED?
It does indicate RADIO-OK, BOOTLOADER-OK, UPDATE SUCSSES, but it does it rly quickly, you said u waited long, in my case it shows USB host mode quickly loading... and the >*>*>*, restart, and the following sucsses, i allso used ETERDIAG for SPL 2.05, hmm, I will try all over again today, i will try to write ETERIMG but i think it will kick me out to bootloader, by the way Happy New Year
nikola92 said:
It does indicate RADIO-OK, BOOTLOADER-OK, UPDATE SUCSSES, but it does it rly quickly, you said u waited long, in my case it shows USB host mode quickly loading... and the >*>*>*, restart, and the following sucsses, i allso used ETERDIAG for SPL 2.05, hmm, I will try all over again today, i will try to write ETERIMG but i think it will kick me out to bootloader, by the way Happy New Year
Click to expand...
Click to collapse
If what you've written is correct then you are two-thirds the way there and what's left to do is connecting your device to your computer with Zune running, Your device is to be in bootloader mode when you do this, look for USB at the bottom and execute the program by right clicking the application and run it as administrator.
I did that, proces said finished and boom no hspl cotula writing......
Same problem with HSPL for me
[/COLOR]
berrywr said:
Okay...your device reads "x310e"; yes? When you re-setup your Gold Card to flash SPL205; your device should have underwent at least one restart and re-entered USB Host mode and you will be looking for the following words "RADIO - OK" and "BOOTLOADER - OK" and "Update Successful, UPDATE COMPLETED"...there would be nothing more on the screen. The next step is restart the device into Bootloader mode, ensure Zune is running on your computer and connect the device to your computer. You open the DFT HSPL folder (the other folder) and you will right click the application and run it as administrator. It should recognize the device and you will select HSPL. This last step takes only a matter of seconds and if successful you will see it almost immediately.
Click to expand...
Click to collapse
i do the same :
ok flash the european rom using ETERDIAG .. ALL OK
ok flash spl 2.05 and everything ok Radio etc with ETERDIAG MODE ALL OK
ok install as adminitrator DFT__HSPL_WP7SG1 and ALL OK
but when i restart it can't find cotulla inside my bootloader
i'm happy because my original rom was only english and now i have european rom but
i need unlock it with HSPL .. grrr
---------- Post added at 06:38 PM ---------- Previous post was at 06:00 PM ----------
06.57 PM 01/01/2013 just finish to RETRY all .... nothing good only my italian rom
not work for me too
No good news
No work for me too