Greets - I came from the Incredible, so I have a BUNCH of chargers (car and wall). Does anyone know if these will work with the Rezound, or if I have to buy a new one (I know Thunderbolt stuff would work; but I didn't have that phone).
Also, anyone know why the phone would flash orange, while off, when plugged into the charger for the first 30 seconds to so, before going solid orange to charge?
If they're microusb and the charger can output 5 volts and at least .5 amps, it will charge. It will charge faster with a charger that can provide more amperage, but that's all.
I use my Incredible charger and USB cable and everything works just fine. The wall charger is actually the exact same charger. As for aftermarket chargers I would assume they would work seeing as the device charges on standard 5v 1A that most USB chargers provide.
I am using the same stand alone charger I used for my Thunderbolt.
Flashing Orange
I prefer to charge the phone with the power off, so it gets a full charge. When I plug in a charger it flashes orange for up to a minute before going solid orange to charge (ultimately going to full green). Any idea what flashing orange means ESPECIALLY in a powered off (but plugged in) state?
Mine never has blinked, just shows orange til charged, then green.
Sent from my HTC
LTE 4G Rezound
I think that the orange blink has something to do with either battery temp or when the battery is fully dead. It happens to me to. I wish the manual had more about it...
Sent from my HTC Rezound using XDA App
I still have a few 5V 700mA blackberry chargers lying around that I use if I have to, but I prefer the one that came with the phone (or the one that came with my dinc -- same output specs) because it charges faster.
Whew
punman said:
I still have a few 5V 700mA blackberry chargers lying around that I use if I have to, but I prefer the one that came with the phone (or the one that came with my dinc -- same output specs) because it charges faster.
Click to expand...
Click to collapse
Punman - THANKS! You are right that my battery was completely dead yesterday. I had charged my first Rezound before using it, but the 2nd one was with whatever charge was on it from the factory. Had been trying to load it up and get it up and running, and was less than 10 seconds from shutting it down smoothly before it ran out. In fact, I was in the process of the shutdown procedure (already hit shut down), but it ran out before it could finish. We'll see what happens tonight.
If the LED is flashing orange it means the phone is unable to power on, for either reason it is too hot, or too dead. Once it goes solid it is charging and is able to power on.
Related
So, I don't know if this is just my device or maybe already known. I don't see it here(or google) so I am going to post this so others can find this info faster than the 2hrs it took me.
Some Li-Ion batteries have a low max charge rate. Meaning you cant "over-current"(mA "Milli-Amps" or A "Amps") them too much(saves life). Well my Razr just showed me this. This can allow you to charge the battery faster if you have one that is tolerant of the "over-current".
Apparently maximum for the Droid RAZR is somewhere between 850mA and 1000mA
Tried using an HTC @ 1A and no joy.. wont charge.. actually says charging.. but the battery seems to have flipped the switch to not charge; and just continues to discharge normally; even the hidden status(dial *#*#4636#*#*) says charging but obviously not! Tried different HTC models and different cables. I am now only using my Moto supplied cable.
Even after it was dead. It would show the charging screen @ 0% and the light would be red. Stating that you cant turn it on cause there is not enough juice to finish boot. It would never go Green no matter how long I waited(10-15 minutes) usually only takes 5 minutes.
Found my OG Droid charger; remembering that it was lower than 1A. It actually is 5v 850mA. Charging away!
Remember the stock charger is rate @ 5v 750mA - this means you can probably use chargers from 700ish to maybe 900ish mA. I cannot confirm these estimates. Anyone else seen any other rates work?
Hope this helps someone down the road. I know it would have helped me!
MODS - Please, if this is wrong info please DO NOT HESITATE to notify me/remove/edit my post. I just want the right info somewhere, cause it was not well documented anywhere i searched via google.
Also - Thinking more on the subject - this could be the "Authorized Charger" bull that Moto likes to put on its devices i.e. The RAZR flip-phone was notoriuosly bad about this. Even my old nextel "beep beep" had this problem with OEM chargers. Had to spend $15+ on the official one. Again - if this info is wrong in ANY way please fix it or remove it.
use official 850mA charger and be happy. Motorola also confirmed using 1A chargers without any problems but any ways original ones are recommended.
Brilliant, my problem now makes sense!
Couple of questions: What does this mean to charging via USB instead of mains? Is it the plug or the cable that is rated to a certain ampage?
One more question. I found another usb plug rated to 300mA. I presume using this will just mean the phone charges slower? It won't have any negative effect on the battery?
Sent from my XT910 using XDA App
Just adding my experience... Have been using an iphone wall charger w/ the usb jack on it and the supplied motorola cable. Its listed as 1000Mah. Battery Monitor Widget shows it charging around 945Mah. Doesn't get hot, charges like a bat out of hell. Down side is phone is about 60% unresponsive during the charge.
Found a little info on this. Apparently different cables, when plugged in, short different contacts to let the device know what it's plugged in to. Resistors change the current. Audio out can tell if it's plugged into a dock versus USB versus wall charger. The Verizon replacement didn't work for me, but an hard incredible one did. They both charged but only the htc recognized computer connections
Sent from my DROID RAZR using Tapatalk
My stock Razr wall charger is 750mA. I use a 1000mA car charger and it works fine - doesn't get hot and charges faster.
But sometimes you do have to be careful. I had a friend who's noob mother fried her Bionic with a charger that was too many mA for it to handle.
__________
Razr XT912 Verizon
HTC Eris via GingerShedBread
strange... my stock charger's rated 850mA.. maybe because i use international GSM version of RAZR.. but it charge just fine..
but even i tried charge it with blackberry's 700 mA charger or my ipod touch 1000mA charger it both charge just fine.. and it feels like the 1000mA charge slightly faster..
too bad i broke my old nokia n900 1200 mA charger..
I'm using an HTC 1A charger: the RAZR doesn't become hot while charging and it's charging faster.
The limit is 1A anyway.
kholk said:
The limit is 1A anyway.
Click to expand...
Click to collapse
dang! so i guess nokia 1200mA charger won't be any good then..
thanks for the info though.. i was thinking of getting myself a nokia charger after read this thread..
Ever since my first motorola I've noticed that the stock charger is 5.1 volts.
Charging with other brands always seem to give worse battery life.
My old Rizr only lasted a day when charged from the USB of my computer, but 6-7 days with the original part.
Some of that is apparent with my car charger too, it says it's taking charge, but sometimes it will run backwards with GPS running..
I experience the charger issue last night.
I had low battery when I went to sleep, put the cable in and it said charging.
Came late to work because the phone drained the battery instead of charging. I used a 5V 1.2A charger and its been working great until last night. And I noticed my original charger is 5.1V 850mA for the Razr.
You learn something new every day!
/J
Has anyone noticed that phone does not charge while using GPS. The charging indicator is on but when I look at the stats it says discharging at -450 mAh. Is this the way it is and if so, is there a fix? 1 hr 42 m with 73% display on battery use and 43% charge remaining, but was plugged in the entire time while driving under an hour home. I am using the same Motorola high performance charger that every other phone is charged fully even when using GPS.
are you absolutely sure the charger is giving the full 1A?
What sensor app are you using to see the battery discharging?
Mine charges normally with gps on.
Sent from my HTC
LTE 4G Rezound
I was curious so I tested this with "Battery Monitor" I have it plugged into my laptop currently which only gives +500mA. and not the +1A that you get from a wall/car/high power usb port.
the app is showing +257mA with GPS on and functioning normally.
So charging good here... Might be something with your motorola charger? It could have a sensor in it to detect 'trickle charging mode' that is improperly engaging when connected to the HTC causing the charger to put out a minimal 'sustain only' level of amperage.
good luck!
you need a charger putting out 1A ... most car chargers put out 500mA so find a good one off monoprice
Here's what I'm doing. I have a Belkin 2.1A(2100mAh) USB car charger dongle. The problem is, once i connect the USB cable to it the phone registers it as "Charging USB" and does notcharge anywhere near as fast(power-wise) as if the phone was registering it "Charging AC". I'm not keen on using a power inverter to get the full AC charge so instead i am going to go pick up a cheap micro USB cable, splice it open, then disconnect the data wires(green & white ones) & then tape it back up. By disconnecting the data wires, the phone will no longer think it's a USB connection and then charge via AC, getting the best charge possible.
that should work ^ if thats the problem
I've found that using the included USB cable with a Belkin dual port USB car charger allows the phone to charge as if it were plugged in to a wall. I'm guessing the included cable has a different layout than standard Micro USB cables.
Sent from my ADR6425LVW using xda premium
dawynkoop said:
I've found that using the included USB cable with a Belkin dual port USB car charger allows the phone to charge as if it were plugged in to a wall. I'm guessing the included cable has a different layout than standard Micro USB cables.
Sent from my ADR6425LVW using xda premium
Click to expand...
Click to collapse
I'm guessing that I have the same belkin dual port (2.1amp and 1amp ports) and the best I've seen out of it is about 250mah charging. This is using the supplied usb/micro hdmi whatever cord for the phone.
I have seen discharge rates off the charger of 750mah which is the highest I've seen on any phone. I'm guessing if you are using the nav on your phone with the screen on, it will probably still be using battery while plugged in.
thatsricci said:
I was curious so I tested this with "Battery Monitor" I have it plugged into my laptop currently which only gives +500mA. and not the +1A that you get from a wall/car/high power usb port.
the app is showing +257mA with GPS on and functioning normally.
So charging good here... Might be something with your motorola charger? It could have a sensor in it to detect 'trickle charging mode' that is improperly engaging when connected to the HTC causing the charger to put out a minimal 'sustain only' level of amperage.
good luck!
Click to expand...
Click to collapse
Possible, but says AC charging in Battery Monitor widget. I will post a few pics.
Here are a few Pics. you can see a couple of things.
-Charger rated at 950 MA out. and no other phone I have owned lost a charge while driving including TBolt, Charge, Bionic.
-Shows as AC charging
- Spikes of good charging detected
Put on Normal power mode today on the way in. live wallpapers did not wrok, just flickered. 3G on vice 4G. Battery still went down, but above 90% on 40 minute drive in. Screen low but on. Bluetooth speaker.
Maybe it is the iBolt car mount. See review online. will try without dock this afternoon on my way home.
-----------------------------------------------------
User: marc frederick, Nov 25, 2011
Pros: Options for different backs
Cons: Does not charge the phone while it is in use
Try playing pandora when the phone is 100 charged. After 45 minutes on the car mount (and yes it is plugged into a charger and all indicatros show it is charging) and the charge level is 84. Using the same charger but plugged into the phone, playing Pandora for 45 min starting charge level 68. Ending charge level is 100.
Yeah, something is telling that charger to not give you full juice
Rezound
ok, drove home off the window mount and just on charger, all same except full brightness on screen.40 minute drive. came up 7% battery vice down from 100 to 43%. nedd a few trials to confirm, but looks like window mount is throttleing juice.
thatsricci said:
are you absolutely sure the charger is giving the full 1A?
What sensor app are you using to see the battery discharging?
Click to expand...
Click to collapse
i have seen spurts up to 913 with GPS off and screen just turned on. Using battery monitor widget. Not on window mount, just charger.
I can confirm. The car dock will not charge your phone atleast not with the screen on and nothing else running but battery monitor widget.
I bought one and tested it extensively yesterday. I used a Verizon 1a charger and a generic 1a charger. With the dock and both chargerz the phone DIScharged(as in LOST battery power) at between 100ma and 200ma. Without the dock using the same chargers and changing nothing on the phone the phone charged at between 50a and 300ma.
I did the test several times to eliminate any random things the phone may have been doing in the background.
After doing that controlled test I played with it some more and no matter what I did I could not get a positive charge with the dock attached even in airplane mode with the screen backlight at minimum. Without the dock using the same chargers i ran Pandora and a police scanner both outputting through the phone speaker, gps, wifi, mobile all on, and screen on auto and still had a very small positive charge.
Moral of the story DO NOT BUY THIS DOCK unless you dont mind it just being a piece of plastic that holds your phone in place.
I wonder if there's a quick mod to it to get it working right. Like the soldering of the USB chargers I've seen.
Rezound
I just went ahead and bought an extra battery so I wouldn't have to charge in the car. Only takes 20 seconds to pop in a new battery.
Can charge both batts while I sleep at night.
Sent from my Galaxy Tab 10.1
I was looking for a high current charger for my Android tablet and there was a review that talked about compatibility. Some of the high cap chargers appear to be designed for Apple products and the pin wiring is subtly different. So, on some non-Apple products, the charge is only recognized as a lower power, 500mah charger and the users reported that some devices would normally charge and others would not. Some of the dual port charges also split the power. The 2.1 amp port and the 1 amp port cannot be used at the same time, depending on what is plugged into them. This was also brand specific. I ordered the Amazon Basics 2.1 amp dual charger and will see how that works. I have noticed a difference in charge rates between my Motorola charger left over from the Blackberry and the Verizon OEM one. The VZW one is faster.
I do the same thing I have been doing since my Windows phone days.
I use the AC cord plugged into a 12v to AC adaptor(screen set to 100% bright and no timeout).
I drove 6 hours last week ruuning Google Maps/GPS & my battery was 100% charged when I got to my destination.
~John
Does anybody else have an issue with their X2 when it's plugged in to either the wall or computer of the screen not responding like normal thus rendering the phone completely useless while charging? It doesn't happen every time, but probably 35% of the time which is still more than it should. And it's not just my phone either, my wife's X2 does it as well and all 3 of the X2's I've had have done it on both stock and eclipse.
Just wondering if anyone else has ran into this issue.
Tapped from my Eclipsed X2
I believe the charger is to blame not comlatible. Not every charger is setup with same pins or wattage... if ur mis-matching equipment.
MIUI X2
I have noticed this. With mine the keyboard becomes sluggish and the lockscreen is hard to unlock. I have eclipse now and it hasn't done that yet.
Sent from my DROID X2 using Tapatalk
I have one charger works just fine and another that when plugged into it I can only use hard buttons. No touchscreen
Sent from my Droid X2 using xda premium
I have five different USB cables and they all work fine. I've never seen this issue before. Weird!
Sometimes mine does this not sure what causes it. Seems like phone is usually warm when it does. maybe it gets too warm with screen and charging at same time. i have had it happen with every ROM even stock.
Sent from CM7 DX2 xda app
I've used my old Crackberry charger along with my usb cord for the cpu, car and wall chargers. Havent had this problem. Strange......
Today it hasn't happened on the same cable at work.
Mine doesn't seem to take issue with any specific charger or cable except for one which is the one that was sent with my wife's phone from verizon, screws both of them up, and it's a moto charger with the same voltage/amperage as the other moto ones, but it has a 9 ft cable.
Tapped from my Eclipsed X2
Interesting it has happened on vz provided chargers. Do theyhave the Moto M on them, or sonething else?
Mine specifically is 5.1V~850mA. Has a USB cable. Has a port we can plug a cable into.
I'd be curious what everyone else has. I wouldn't think it's the cable itself but working in technology, I've seen stranger things.
Sent from my MB870 using XDA App
It could be one of two things, either:
1. you're using a usb cable with a broken data pin.
2. you're using a charger that doesn't output enough current.
the problem lies in a lack of available current in a certain charging state, a "fast charge" if you will. you get either not a high enough sustained supply voltage, or "dirty" power (essentially a little AC in your DC) and that really screws with the capacative touchscreen.
with a bad cable, the phone thinks it's plugged into a charger and not a usb port so it will try to draw up to 850ma from a port that can only feed 500ma if you're lucky.
with a bad charger, or one incapable of supplying the required current, you get "DC ripple" where your voltage fluctuates up to half a volt or more, 60 times every second. generally your phone will get very warm under this condition as well.
so it could be a cable, a charger or a combination of both.
some car chargers are notorious for making dirty power... so are some cars...
Cheapxj said:
It could be one of two things, either:
1. you're using a usb cable with a broken data pin.
2. you're using a charger that doesn't output enough current.
the problem lies in a lack of available current in a certain charging state, a "fast charge" if you will. you get either not a high enough sustained supply voltage, or "dirty" power (essentially a little AC in your DC) and that really screws with the capacative touchscreen.
with a bad cable, the phone thinks it's plugged into a charger and not a usb port so it will try to draw up to 850ma from a port that can only feed 500ma if you're lucky.
with a bad charger, or one incapable of supplying the required current, you get "DC ripple" where your voltage fluctuates up to half a volt or more, 60 times every second. generally your phone will get very warm under this condition as well.
so it could be a cable, a charger or a combination of both.
some car chargers are notorious for making dirty power... so are some cars...
Click to expand...
Click to collapse
Oddly enough I have zero problems with the car chargers, the phones work fine when plugged into them.
Yeah the newest cable is one that is USB and 9 ft long but not moto one that verizon sent with my wife's phone. The moto one that came with mine an the two moto ones I got from Amazon I don't have any issue with but the cables are so stinking short they are a pita to use anyway (2' cables).
I've also noticed that the USB ports on different computers charge at different rates as well. My work computer will barely charge the phone and sometimes can't even maintain the battery level if I'm using it. My laptop at home charges it pretty good but you can't use the phone because you get the screen issue again.
Tapped from my Eclipsed X2
Yeah, I have had this same issue for quite some time and after reading this forum tonight I tried a new charger and BAM, problem fixed! I had thought it was my phone, but it was definitely the charger. The one I was using was the Verizon 9ft charger they send out with replacement phones. Model: B141000. Black with green on the back. Gave my wife my charger that came with the DX2 to take to work and use because I liked this big long cord. So for months now whenever I tried to use the phone while it was charging it lagged so bad I would have to continuously unplug it and plug it back in when I was finished. Needless to say, having a text conversation when battery was almost dead was really annoying...
So when I read this post tonight I went up and grabbed my old Samsung charger from my old Samsung Fascinate and sure enough it worked just fine... No lag what so ever. So I am guessing it is an issue with the DX2 and the generic Verizon charger they send with replacement phones not being compatible...
Furthermore just as a test I just tried the actual 9ft USB cord with the Samsung plug you plug into the outlet and its still working fine... So I assume its the Verizon plug part not putting put enough voltage or something. Pretty happy that I can seemingly still use my 9ft cord! So if you have a spare plug I would say give it a try!
I have a ton of micro-USB chargers that I've used with my GNex and Evo3D with no issue. The only consideration I take into account is Amperage, and I toss the ones below 800 mAh. Last night I plugged into one thats around 850 mAh and left my phone to charge all night (at around 5%). When I woke up, the phone had completely discharged without any sort of recharge.
Since this isn't a Nexus phone, am I locked in to only using verizon branded chargers? Is there a way to defeat that with root?
I haven't had any issues with that as I use all different types. Maybe just try another or maybe it wasn't plugged in all the way.
What voltage is it rated at? It could be that or that the charger is bad somehow. I charge mine nightly with a .7A charger and it's always been full when I wake up (about 30-50% when I go to sleep).
I have the sprint note 2 but they are essentially the same phone so here is what Igot for you:
there is no "smart" element to any chargers in the market, so your phone shouldn't know the difference between Verizon brand and the devil's own brand
if you look at the stock charger it outputs 2 amps...the phone needs this and in my experience it needs at least 1 amp in order to charge instead of discharging slower
also there is a known issue with all note 2s that the cable will not sit snugly inside the port causing it to be a bad connection... just make sure you put it in hard (no pun intended) and it shouldn't be a problem
Sent from my SPH-L900 using xda app-developers app
Sent from my SPH-L900 using xda app-developers app
Yeah, if you take a close look at the micro-usb port, it is recessed a bit. Make sure you plug the cable in firmly.
reinaldistic said:
also there is a known issue with all note 2s that the cable will not sit snugly inside the port causing it to be a bad connection... just make sure you put it in hard (no pun intended) and it shouldn't be a problem
Click to expand...
Click to collapse
I think this was likely the issue. The charger is rated at 1 Amp, and I tried it out again last night and it appeared to work for the few seconds I had it plugged in, so I must not have had it in there snugly.
So I just tested with the same charger, and when I plug it in, it beeps every half second and flashes between the charging/discharging symbol, and does not charge...
apols said:
So I just tested with the same charger, and when I plug it in, it beeps every half second and flashes between the charging/discharging symbol, and does not charge...
Click to expand...
Click to collapse
I don't remember where, but I remember reading about someone with this issue where they were using their phone as a gps while charging it and it died. Someone commented saying that the culprit was probably a faulty charger. Sounds like they were right.
apols said:
So I just tested with the same charger, and when I plug it in, it beeps every half second and flashes between the charging/discharging symbol, and does not charge...
Click to expand...
Click to collapse
I have seen this same thing with two Droid X's plugged into the same 2A charger. One phone would charge and the other would do exactly as you describe. It didn't do it all the time, it just depended on how low the battery levels were on each device. How much battery life do you have left when it does this? You may just need to use a higher amperage charger.
I have not received my Note II yet, but it sucks that I will most likely not be able to charge it while tethered (USB) to my laptop.
Based on the info I could find (kernel driver), the phone will accept up to 650mA of power, so anything over that should charge the phone at the same rate. Voltage shouldn't be an issue as it is charging via USB, which is 5V (+/- 5%). Unless someone has an amp probe to put on it, we can't tell if it is actually pulling more or less than what the driver specifies. And, as someone else stated, the phone can't tell if you're using a genuine Samsung cable and charger, or a $1.00 made in China cable/charger, as long as they both output the same voltage/amperage, the phone will never know the difference.
Based on what you said though, if the phone is constantly seeing the charger connect/disconnect, that would drain the battery even faster.
Hi everyone,
I have just swapped my Galaxy S3 to a HTC One X+ because I couldn't stand Samsung's Touchwiz, and I love Sense 5. The downside is the charging times on this new phone are pretty laughable!
Now I know different cables can give different currents consistently, but I have three cables (one at work, one in car, one at home) that would all deliver 1000mA to my GS3 and I could go from 10% to 100% in about 90 minutes, about 1% per minute, it was great! Battery life on this phone never degraded so I know 1000mA wasn't damaging at all (all GS3s can take a maximum of 1A).
I've now moved over to the HOX+ and it's taking absolutely forever to charge, between 3-4 hours to charge from low. I simply can't wait this long, it's beyond a joke :crying: I've checked Better Battery Stats and my battery usage is about the same as my GS3 when unplugged (about 4-5% per hour) which is fine, so why the difference in charging times?
On my GS3 I had an app which showed me charging current that was specific to GS3s and was very reliable, but I can't seem to find a reliable app for the HOX+, the one I have is Battery Monitor Widget and it reckons I'm charging @ 330mA and I'm currently at 22%, that can't be right can it?
Here is what my phone is says when charging "Charging (USB)".
In the past hour it's done about 20%.
Sent from my HTC One X+ using xda app-developers app
Keydogg1 said:
Here is what my phone is says when charging "Charging (USB)".
In the past hour it's done about 20%.
Sent from my HTC One X+ using xda app-developers app
Click to expand...
Click to collapse
Erm thats the issue. When you charge using the AC (By cable to the electric socket) it says "Charging(AC)" . This usually takes me from 10-100% in about 90 minutes with the HOX+.
Somehow either you are connecting it to a usb hub (laptop or a computer) which is pretty slow compared to the AC, or your phone is mixing up the AC and USB currents. So an advice, use an electric socket and make sure it says "AC" in the power tab. IF so, check the charging time you should find it similar to that of Samsung.
I also think usb 3.0 is faster in charging than 2.0 ? If you are on a new pc with a new motherboard you should find your sockets 3.0, so don't use a usb hub especially if it says usb 2.0 since it will be pretty slow.
Hi Gand0ur, thanks for the advice.
I should have said before; I never charge via a computer/laptop/USB hub. Only directly into the wall. It is an aftermarket charger but it's a good quality one as it charged my GS3 @ 1A and also my old Sensation charged in about 90 mins.
I've just tried a different cable and still the same outcome. I'll try another wall plug when I get home tonight
Keydogg1 said:
Hi Gand0ur, thanks for the advice.
I should have said before; I never charge via a computer/laptop/USB hub. Only directly into the wall. It is an aftermarket charger but it's a good quality one as it charged my GS3 @ 1A and also my old Sensation charged in about 90 mins.
I've just tried a different cable and still the same outcome. I'll try another wall plug when I get home tonight
Click to expand...
Click to collapse
Sorry.. I am kinda sleepy so I posted without saying any thing. Anyway I wanted to post a pic of the text on ny stock charger. Says the following : output: 5v ~ 1A .
I will post a picture when I wake up in a couple of hours.
Sent from my HTC One x+ using XDA developers app
Ghand0ur said:
Sorry.. I am kinda sleepy so I posted without saying any thing. Anyway I wanted to post a pic of the text on ny stock charger. Says the following : output: 5v ~ 1A .
I will post a picture when I wake up in a couple of hours.
Sent from my HTC One x+ using XDA developers app
Click to expand...
Click to collapse
No problem! The charger I am currently using is a 5V/2A (for tablets) and has worked fine for every phone previously, giving 1A current.
Keydogg1 said:
Hi Gand0ur, thanks for the advice.
I should have said before; I never charge via a computer/laptop/USB hub. Only directly into the wall. It is an aftermarket charger but it's a good quality one as it charged my GS3 @ 1A and also my old Sensation charged in about 90 mins.
I've just tried a different cable and still the same outcome. I'll try another wall plug when I get home tonight
Click to expand...
Click to collapse
dont ever use after market charger even though it is for tablet or note samsung...i tried and it is prety damn slow...
so just use your htc/stock charger...it will be fast charge...2hr the most maybe less...
anyen said:
dont ever use after market charger even though it is for tablet or note samsung...i tried and it is prety damn slow....
Click to expand...
Click to collapse
That isn't necessarily true. This charger has been the fastest thing to ever charge my HTC Sensation and GS3, and come to think of it my Nexus 7 charges faster with this charger too. As I said earlier, I had an app on the GS3 which showed it was outputting 1000mA (maximum the GS3 allows) and it would charge that phone in around 90 mins. According to the HOX+ app I have I'm only getting 330mA. Whilst I agree that poorer after-market chargers often give dubious results I'm confident that this isn't the charger's fault.
I'll try the a HTC charger when I get home, but the other night I had it on charge with the HTC charger and it didn't seem to move very quickly.
I'll just say what I know from experience with my HOX+: it only seems to be charging in a normal (and pretty fast) way with the original, from the box, charger.
I tried charging it with the charger from a Desire Z - slow; charger from Desire S - slow; a Nokia charger - slow.
I also noticed that while the Desire S or Z can get charged while being used, when using a car charger (a Nokia one), the HOX+ seems to be using more current, and it ultimately dies. It happened this summer, so this might be an issue.
geojoking said:
I'll just say what I know from experience with my HOX+: it only seems to be charging in a normal (and pretty fast) way with the original, from the box, charger.
I tried charging it with the charger from a Desire Z - slow; charger from Desire S - slow; a Nokia charger - slow.
I also noticed that while the Desire S or Z can get charged while being used, when using a car charger (a Nokia one), the HOX+ seems to be using more current, and it ultimately dies. It happened this summer, so this might be an issue.
Click to expand...
Click to collapse
I think you're right! I tried my wife's HTC One S charger last night (because the HOX+ doesn't come with one) and it changed to Charging (AC) for the first time. I have to say this is a massive let down for me, my car charger saved me so many times with my GS3 (for example I drove to Scotland and used GPS all the way, and the phone still charged right up at the same time) I'm not sure I can handle it not being able to cope with other chargers.
I find this extremely frustrating Is there not a hack to get around this with root?
I'm not sure about the Samsung, but the HTC will only go into the fast/AC Charging mode when it see the Data+ and Date- signals shorted on the USB port. This can be designed into the charger, such as the factory HTC wall charger, or you can buy "charging only" cables and then use any USB charger to get your HTC to go into AC charging mode. These charging only cables are tough to find, but amazon does sell them. Keep in mind that the charging only cables will not transfer data at Data+ and Data- are shorted. Once you are in AC charging mode, the phone takes over and determines how fast to charge. At low battery levels (less than 80% or so), the charging rate can be as high as 1000ma/h or the maximum the charger is rated to deliver. If the charger is rated to deliver more than 1000 ma/hr, the most your phone will draw is 1000 ma/hr.
Now there is another variable, the cable itself. Cheap cables sometimes have too much resistance to pass 1000ma/hr and can be the problem as well.
One other issue is the number of knock off chargers and cables out there. Beware of e_ay. You may not be getting what you think you are.
One final note, Apple designs the ipod to look for the Data+ and Data- signals to not be shorted (opposite of HTC and most android manufacturers). So chargers that are designed to charge Apple devices will need the Charging Only cables to charge android devices in the AC charging mode.
So if I didn't confuse myself, hopefully this will answering some charging questions. I've researched this and have tested many chargers and cables.