first charge once you get the rezound?? - HTC Rezound

hi I've heard plenty of times that you should charge your phone once you get it or charge overnight..is this true in anyway? I always go straight to playing with my new phone and then charge once battery dies..any thoughts on this myth?

Hi. I have heard a few different things about this. I think there is a thread on here I read about it as well.
First is that it won't matter because batteries no longer need to have that memory thing.
Then there was one that said let it deplete, charge it and then when the light goes green unplug it and replug it in. The light will go red for a few more minutes and then green. That will set the battery.
Then I also read that you shouldn't charge it completely or let it completely deplete because that will lessen the charge over time
The last I heard is that (and this was under the discussion about extended batteries if I remember correctly) the batteries are made so that the battery meter tells us it is dead even though there is still a little bit of a charge on the battery that way it doesn't do anything bad to it.
So I really think it depends on who you listen to. I did the let it deplete and charge it thing once so far. I get decent battery life. I tested it and got 10 hours out of it with medium usage and I usually get more when I toggle off the 4g when not using it but haven't timed how long for that yet.
Hope that helps until someone who knows more specifics posts something.

jonathan413 said:
hi I've heard plenty of times that you should charge your phone once you get it or charge overnight..is this true in anyway? I always go straight to playing with my new phone and then charge once battery dies..any thoughts on this myth?
Click to expand...
Click to collapse
I don't think it matters any more. I plugged mine in after I did initial setup and let it charge to green light, didn't do any special bump charging or charging while off. The battery is designed to be used as is, without any tricks. Always overcharging to 100% or completely draining to 0% is probably worse than just using it normally and plugging it in when you notice it's relatively low.
There's a battery log that Android keeps regarding voltage and reported capacity that it uses to adjust the percentage display that you see on your phone. This changes over time as it gets a better idea of how the battery discharges, so built into your phone is a mechanism to make sure the reported capacity is accurate. If it gets "off" a bit, like if you see a huge spike up or down in battery capacity after a reboot, it's just adjusting itself.
But, as you know, Android users love to control everything by themselves, and not leave anything to some process behind the scenes. Hence the clamor for root so we can install whatever we want. So some people like to trick this adjustment mechanism by force charging the phone to full when it's off, which gives the battery capacity adjustment mechanism a "true" full charge to base its reporting on. Also, I don't believe the kernels in stock ROMs will charge to what it believes a full 100% charge is, to protect the battery life. Bump charging kind of gets around that, if I understand the process correctly.
Also, I don't charge overnight (lack of outlets in bedroom) so I make sure it's topped off before I go to bed. Even if it's not, it can make it through the night just fine, since it's not being used. So that's not that much of an issue anyway.
TL; DR: Just use it, plug it in when you need to.

Related

[SOLVED] + [BRAINSTORM] Battery Calibration

Just wanted to open up a thread here to see what we can do about battery calibration issues.
Not sure, but I read around that people are getting phone shut downs at the 10%-15% ranges.
When in actual fact it should be somewhere around the 1%-5% range?
Was wondering if there is some possibility in coding the phone to read the battery state better? Thus, eliminating the need for calibrating the battery through tradition means (ie: wiping, charging, etc)
Thoughts?
EDITS:
We've managed to figure out huge boundaries for the battery.
There are currently two ways to get your battery into "learn mode" - which will adjust the values of your battery to accurately reflect it's "age" and mAh tracking. This will lead to a fix for those of you who are currently facing issues with the battery shutting down anytime before the 1% mark.
1st fix:
1) Drain battery
2) Just as the battery hits "Shutting Down", plug in your charger
3) Let the phone power down
4) DO NOT TURN ON THE PHONE
5) Let it charge up overnight or something along the lines of 4-6 hours, which should ensure it will be fully charged
6) Power up, your phone should be calibrated and will now shut off at 1%
2nd fix:
Head over to the Battery Calibration Tool Thread which spawned off from the discussions here!
>> http://forum.xda-developers.com/showthread.php?t=765609
For those who have been following the thread and wonder what your status_reg value mean theloginwithnoname has kindly provided us with some datasheets and translations, which you can get with the following links:
Binary Conversion: http://forum.xda-developers.com/showpost.php?p=8013370&postcount=548
Then refer to Page 25 of the following datasheet: http://datasheets.maxim-ic.com/en/ds/DS2784.pdf
OR you can try out mtw4991's method to get learn mode done with the battery app that's been created out of this brainstorm thread.
The link to his method is > http://forum.xda-developers.com/showpost.php?p=9583271&postcount=340
I began this thread in other to simply find a fix for our current battery % meter. Basically, users (myself included) were having a problem with inaccurate battery % readings. Some N1's would shut down above 1% and this would leave many guessing when the battery would give out.
Needless to say, here at XDA - we managed to find the fixes. ;-)
And of course, we decided to take it to the next level.
How can we now push more out of our batteries?
RogerPodacter and theloginwithnoname have been working endlessly learning and understanding the how the battery registry works and together with dvgrhl they're finalizing a battery mod app which will help the N1 cope with the "learn mode" and changes. So do thank them for the great work they've been pushing out with! =)
They've helped us hammer out all the core details concerning the battery understanding, values, binaries, and we're wading through the mess to push the limits on the batteries (short of blowing them up as usual of course).
Be patient if the app isn't ready yet. And if you're a n00b, please don't mess around with the registry values and such if you have absolutely no idea what you're doing.
No one is gonna give a rat's poopoo if you blow up your phone and set your house on fire and gremlins kidnap your toes.
Peace out.
This thread is and methodology has served its purpose and many of us from this thread have moved on over to the Battery Calibration TOOL thread. The methods still work, but so do the newer methods at the tool thread, which I personally find is much easier and better.
If you'd like to use the manual method, it'll still work.
For those more interested in the newer method and I encourage you to do so - head on over through this link > http://forum.xda-developers.com/showthread.php?t=765609
+1
It happened to me yesterday. I am playing with my phone and I needed to check an important address on Google Maps, so I was thinking "Oh great I still have 9% battery" and then all of a sudden BOOM. It powered off. I mean seriously WHY have those extra 9% if I am never going to use them. So In reality my phone battery is like 80%
100%-(first 10% which drain in like 5-6minutes) - 10% that I never use cause the phone shuts off = 80% BOOOOOOOOOOOOOOOOOO NOT COOL
happened to me on cm 5.0.7.1 about 7% battery
I guess this would be an appropriate time/place to ask this question. I had someone PM me asking how to calibrate their battery and I didn't know if I provided them with the correct response. What I've always done is let the battery drain ALL the way down until it dies~usually about 1% and then fully charge the phone while it is off. Then, let it die down once again on that charge and repeat the charging while the phone is off. Is that the correct way to calibrate the battery or am I taking unneccesary steps?
THATTON said:
I guess this would be an appropriate time/place to ask this question. I had someone PM me asking how to calibrate their battery and I didn't know if I provided them with the correct response. What I've always done is let the battery drain ALL the way down until it dies~usually about 1% and then fully charge the phone while it is off. Then, let it die down once again on that charge and repeat the charging while the phone is off. Is that the correct way to calibrate the battery or am I taking unneccesary steps?
Click to expand...
Click to collapse
No idea as well honestly. I've never charged my phone while it's off... so that might be the issue...
But then again, my phone has often turned off at the 10% mark. So that's why I thought I'd get more input here on how we can actually find a way to calibrate our batteries or something.
i have two oem batteries and a dock..Everyday I completely drain the first and swap it out with a fully charged one off the dock and both batteries perform great and never shut down above 1% every single time. So the batteries are always completely drained and then have a slow no stress recharge, maybe this is why mine go to 1%?
chowlala said:
No idea as well honestly. I've never charged my phone while it's off... so that might be the issue...
But then again, my phone has often turned off at the 10% mark. So that's why I thought I'd get more input here on how we can actually find a way to calibrate our batteries or something.
Click to expand...
Click to collapse
I notice that if I charge my phone while it is off and take it off about 20 minutes after the light turns green, the discharge rate is MUCH slower than if I charge it while the phone is on. Or, I will charge it while on, let it get to 100%, turn it off and continue to charge until the light turns green again. Either of those two ways give me the best results for battery life.
Doesn't the Li-on type of battery calibrate itself when charged from 0% (or the specified minimum) to 100%?
THATTON said:
I notice that if I charge my phone while it is off and take it off about 20 minutes after the light turns green, the discharge rate is MUCH slower than if I charge it while the phone is on. Or, I will charge it while on, let it get to 100%, turn it off and continue to charge until the light turns green again. Either of those two ways give me the best results for battery life.
Click to expand...
Click to collapse
Hmm. Interesting thought. Guess letting it charge to 100 while its on is one thing, then turn it off so it maxes out before daily use. I'll try that tomorrow morning and see.
Stats have been recalibrated to pershoots kernels already. So tomorrow will be a good testing day.
LiOn batteries should NOT be drained completely. It is bad for them. You should simply charge to 100%, turn the phone off, let it continue to charge (you may be at 100% when in OS but not truly 100% to the battery) and then wipe battery stats.
hah2110 said:
LiOn batteries should NOT be drained completely. It is bad for them. You should simply charge to 100%, turn the phone off, let it continue to charge (you may be at 100% when in OS but not truly 100% to the battery) and then wipe battery stats.
Click to expand...
Click to collapse
Yeah, the discharge part is actually true. There's more info here bout the batts, but nothing much bout calibration.
http://forum.xda-developers.com/showthread.php?t=669497
chowlala said:
Hmm. Interesting thought. Guess letting it charge to 100 while its on is one thing, then turn it off so it maxes out before daily use. I'll try that tomorrow morning and see.
Stats have been recalibrated to pershoots kernels already. So tomorrow will be a good testing day.
Click to expand...
Click to collapse
The biggest thing I noticed right off the bat in doing this was that normally my battery drains from 100% to 90% in less than 30 minutes. After doing what I suggested, I see that my battery discharges much slower from 100% to 90%! Hope it works for you.
My phone was doing that ALL the time. Here's what i did that fixed the issue for me.
1.) Let my phone die as usual.
2.) KEPT IT DEAD... for 1 day
3.) Charged with the phone OFF for 1 day.
4.) Went to RA's recovery as soon as i turned the phone on and reset Battery Settings.
5.) Rebooted and all is well.
I hope this helps someone else.
(My phone would die at 13% EVERY time. It got really annoying when trying to Navigate when i forgot my USB cord for my PowerCup. :< )
And yes i know about the whole not letting Lion Batteries die. When i worked for T-Mobile and the customers would bring in their N1's doing this, every call to HTC this is what they told me to do. (Minus the whole awesome recovery and such). They said letting the battery drain will not hurt the phone as long as it regains 100% charge after the initial drain.
AGAIN. This worked for Me. So im not promising you anything. Plus the batteries are only 25 bucks from Google. And i have 4 extras... Just in case. I would invest in some if i were you. Cause lord knows, were going to do some SERIOUS stuff to our phones. Extra Batts dont hurt.
Lithium batteries don't have memories, that's a leftover idea from the old Nickel Cadmium (NiCad) and NiMh (Nickel Metal-Hydride) days. The idea with Lithium (Ion & Polymer) should pretty much just be charged up whenever. Letting them be drained completely isn't good for them and will reduce their lifespan (reduced mAh) although it won't almost immediately kill them ala lead-acids. Overcharging them via a circuit with a poor cutoff also isn't good for them as they'll heat up, phones or any decent AC charger should stop charging when they hit 100% though.
Probably about the best you can do is charge it to 100%, pull the battery and reboot the phone and then reboot it again. The charge calculation will be based on the rated mAh of the battery which depending on the quality of the battery and the charging system of the device could end up giving you some funny figures. Not much you can do about it though.
I just wanted to say that this link does mention a proper calibration charge, it just does not go into detail.
Item 3 of "General Lithium-Ion Battery (LIBs)Usage":
• Although it is said that LIBs do not have memory, it's not entirely true. LIBs have gauges that monitor performance of cells, and if you do a lot of small charges, it won't let those gauges to monitor a full battery potential, causing an invalid indication of charge level. A complete charge/discharge should be made when battery capacity seems reduced, that will calibrate gauges and they will provide your phone with correct charge level status. A full charge/discharge cycle should be done every 30 (or so) partial charges.
Click to expand...
Click to collapse
My assumption of a complete charge/discharge cycle would be:
1. drain battery until the device dies
2. charge the battery to 100%
3. power device on
4. drain battery fully until device dies (no small charges!)
5. charge battery to 100%
This should allow the battery gauges to recalibrate and improve battery capacity.
People seem to be in the dark about lithium ion batteries, how they are charged, and how the device estimates battery charge remaining.
Lithium batteries do not have memory effects, but the phone does keep a file with charge info about the battery; it uses this to estimate charge left and how to charge safely when the device is powered on.
When properly charging a Li-ion battery, the last 10% of the charge should take almost as long as the time it takes to charge from 0 to 90% (well about half as long meaning a full third of the charging time should be going into the last 10% of the charge) Charging with the device off, charges the battery more completely and consistently.
Li-ion battery chargers use a type of charge cycle called constant amp/constant voltage. The battery will be force fed amps until the battery's voltage peaks and it will then be fed a constant voltage. (around the 90% charge mark) During the constant voltage phase, the amps that the battery is taking in will be monitored; as the battery gets closer to full charge the amperage will drop more and more, until it is just a tiny trickle. When it gets to that point, the battery is fully charged. Obviously charging with the device still powered on creates a problem for that type of charging. So the battery can only be charged to the peak voltage, then the charge cycle must stop; as the last 10-15% of the charge can not be completed safely.
It is always good to let a device run until dead and then charge with the device off a couple times when the device is new, and then charge the device from empty while powered off once every couple months. (do not do it too often, as Li-ion batteries prefer to be between 50-80% charge for longer service life) This allows the device to maintain a proper reference data file on the battery and its charge state. this data file is what Android uses to estimate the charge in the battery, if the file is not accurate, the device may power down sooner than it should, or not charge fully to a true 100% state. (peak voltage state when powered on that is)
Also, Li-ion batteries are rated for capacity from a discharged voltage of 3v. So a 1500Mah battery is rated to provide 1500mah of power from fully charged to a final discharged voltage of 3v.
I do not know what the minimum operating voltage of various devices is, but if it is higher than 3v; then the phone must shut down at its min operating voltage and not the 3v needed to get full capacity. My Nexus one shuts off around 3.5v so there is around 25% of the actual rated battery capacity left. (remember what I said about Li-ion batteries liking to be between 50-80%, this left over capacity means that running the battery dead repeatedly is less harmful than if you drained the battery to a true 0% state)
There is also a voltage drop on a battery when under load. So if you are putting a heavy load on the device (like a 3D rendered game heavy gps use) then the battery voltage may drop to below the device’s min voltage. This means that if the phone shuts down during this time, you could probably turn it back on and get a few hours of standby or a few more minutes of light use. This could be another cause for people seeing shut downs when the battery gets around 10%.
The amount of power in a battery is high, especially in Li-ion batteries with their high energy densities. Over charging a Li-ion battery can cause an explosion, literally, that little battery in your phone could remove some fingers. Over discharging is bad as well, as it can start a fire; though like I mentioned above, the cut off voltage is above the 0% state, so that is unlikely here.
Ive proposed this before and got a bit shouted down, but thumbs up if anyone comes up with anything
As i see it, its not a problem with the battery. Its a problem with the battery meter. Since following a regime of deleting my batterystats.bin file, i dont see that issue. Its the same on my g1 as it is on my n1.
This is what i do... when i charge my phone, i charge it until 100%. When it reaches that 100%, i use either use the terminal or root explorer to delete the batterystats.bin file. After which i immediately power off the phone. Now, when its powered off(and still attached to the usb charger) the light should be green. But usually its not! Sometimes it charges up to a full hour longer before it turns green! When it turns green, power the phone back up and enjoy tue extra kick of battery life. Its not actually gaining battery life, its just resetting tue battery meter in the phone. This could only be done with a rooted phone. Oh, i think that this whole innaccurate battery meter thing is a problem with android in general. The meter becomes innaccurate with time. Sometimes extremely innaccurate.
Using the terminal...
su(press enter)
rm /data/system/batterystats.bin(press enter)
Then power off
Wow. Lotsa pewpewz here. Haha.
Again, after all the discussions, seeing that most of us agree the N1 keeps "stock" of how the battery chargers, is there a way for us to check or see how the battery is being calibrated, etc?
Not so much an app to modify the calibration, cuz that'll just be too dangerous, but something more like a tool to monitor it, so we know if it's calibrated right or wrong.
Deleting the batterystats.bin file isnt an app. Its either a script you run to delete it or physically deleting it. And its not dangerous. Ive done it well over a thousand times with my g1 and n1 combined. If you wanted to find out how the calibration work, i guess you could make a copy of your batterstats.bin and read it

[Q] Why do soo many people recommend something soo bad for your battery?

One of the worst things you can do to a lithium battery is discharge it completely. They don't suffer from "memory" yet every time someone here in the forums complains that they are getting crappy battery life the instruction to discharge and recharge to 100% before clearing stats pops up.
For those who are interested here is an article that explains in detail.
batteryuniversity.com/learn/article/how_to_prolong_lithium_based_batteries
My main question- Is there some function in android that looks at the maximum depth of discharge level of the battery or is it that most people don't understand the characteristics of L-ion and confuse them with those of Ni-Mh or Ni-Cad?
I want to know because if I need to completely discharge to get better perfomance, despite the reduction in charge cycle lifetime, I will do it but only infrequently.
I've only let my battery discharge completely once, and it wasn't on purpose. From the posts I see here I think I get above average battery life. About 18 hours miui before I go for the charger and on 2.2 roms I'd get 20 hours and still have 40% or so to go. So no I don't think completely discharging your battery does anything for battery life.
Sent from my T959 using XDA App
I have never run mine down completely. Gotten it to about 6% but that was because I was fighting ROM flashing problems. I usually call 25-30% enough for me and plug in then. I am also getting 30 hours out of my 2.2 with a good deal of use. I used to have a Motorola and their batteries are total crap. If you EVER let it get down below 10%, it took some real work for it to charge correctly and boot up. Even as much as a hardware mod where I have had to cut the wires on a USB charge cord and charge it rigged up with the wires pressed against the battery and prongs in the phone. Very dangerous, but worked for a last resort.
Discharging the battery is not for the sake of the battery,but more so for the ROMs data and how it acquires the battstats usage. I only run it up and down and clear stats when flashing a new ROM, but I do use my phone moderate to heavy daily and have had great success in battery life the way I calibrate it.
The solution I think is to use a larger capacity battery and regulate it to narrower window of operation never fully charging or discharging.
The fastest killer though seems to be heat.
I have read several times that your phone does not fully discharge the battery...that there is still a minimal amount of charge,not enough for the phone to opperate but enough to not damage the battery when it shuts down
Maybe the batterystats file can be saved after being calibrated once and then restored after every wipe oor flash.. that would save some time aabd according to you guys, batt life too
Sent from a cell tower to the XDA server to you.
I've only ever calibrated my a few times and only after flashing a new rom. I never run my battery down after resetting the stats. I just use my phone as I normally do. My understanding of calibration is that it's not about squeezing more life out of the battery despite what most people think but of getting a more accurate measurement of the battery's actual charge. Also while it's true that the phone will shut of before the battery is completely discharged damaging the battery, allowing the battery charge to drop that low shortens your battery's life and decreases the amount of charge your battery can hold.
What gets me is I also read somewhere that for optimum battery life you should keep your battery level somewhere between 70%-40%. Of course that doesn't stop me from charging my phone to 100% everyday. I don't remember where I found that article but I'll post a link if I can find it again.
The reason this bad advice about completely discharging your battery persists is probably the same reason people keep recommending automatic task killers.
batteryuniversity.com/learn/article/how_to_prolong_lithium_based_batteries
ok, ok ill volunter, ill watch porn till my battery"discharges" At least my log will be interesting
radiohd said:
One of the worst things you can do to a lithium battery is discharge it completely. They don't suffer from "memory" yet every time someone here in the forums complains that they are getting crappy battery life the instruction to discharge and recharge to 100% before clearing stats pops up.
For those who are interested here is an article that explains in detail.
batteryuniversity.com/learn/article/how_to_prolong_lithium_based_batteries
My main question- Is there some function in android that looks at the maximum depth of discharge level of the battery or is it that most people don't understand the characteristics of L-ion and confuse them with those of Ni-Mh or Ni-Cad?
I want to know because if I need to completely discharge to get better perfomance, despite the reduction in charge cycle lifetime, I will do it but only infrequently.
Click to expand...
Click to collapse
Discharging the Battery & Running the Battery Dead is 2 Different things!
We recommend running the battery dead ( Phone Shuts Off ) & recharging while off to train the Android OS from Full > Empty..
Running the Phone until Dead is not Going to hurt the Battery in anyways shape or form despite what you may think or read!
The Reason is, the battery is never fully Discharge & still holds Voltage.. The Calculations of Charged / Dead is at the Kernel Level, so even when dead it still has a 3.4v still or roughly..
As long as the kernel isn't tampered with, discharging the battery via the Phone will never hurt the battery period!
Now, Based on the link you posted you would have to run the battery down past the safe discharge point.. Via some other means of killing the battery, other than using the Phone.
To help ease your mind, Remember this:
~ Charge levels is controlled by the kernel
~ Even when Phone powers off, there is still plenty of charge in the Phone's Battery
~ Battery is never Fully charged, as this also hurts lithium batteries
Roughly every Android kernel does not let lithium battery get below 3.4v and at most 96% charged.
Hope this helps,
~Eugene
If you are still concerned wait until your phone turns off and stick your battery on a meter. You will see there is still power left in it...
My original battery that came with the phone got great life, then couple of months later it was discharging in like 2-4 hrs(froyo), so I called, they sent another one free...5-6 months later that one started doing it as well, so I pulled out the old one from the drawer, it powered on at like 85% ! and I was getting crazy ass life out of it on miui over 30 hrs one time...now that one is acting up again, so I'm going to try to swap again..lol...maybe there's something to not using them for a while...
I've used diff roms and combinations of draining/recharging...calibrating, not calibrating...it's always different results..honestly I don't think there's any rhyme or reason to it other than the fact that many vibrants have diff hardware and there will always be some weird quirk on a per user basis...
As far as hurting it by draining it all the way, I hardly think that's the case seeing as with both batteries I've always let it run down...not on purpose but there has been many many times I've plugged in at 1% or had to power back on because it died...charged it up and got 20-30hrs no prob..usually issues come up when flashing a new rom...
i think it all comes down to luck of the draw. ive had my vibrant since launch day, and i still manage great battery life. my battery is actually stamped 7-02-2010. every 2 weeks or so ill drain the battery completely, turn it back on and allow itself to die again, and finally allow it to fully charge overnight or 4 hours. i usually get a good 7-8 hours of constant use on cm7, or over 24hours if let on standby.
im still debating if i want to grab an epic 4g touch battery as well to increase it even more.
qpinto said:
im still debating if i want to grab an epic 4g touch battery as well to increase it even more.
Click to expand...
Click to collapse
what's this about?
Epic 4g batteries are 1800 and fit in our vibes.
Dr.Stainedglove said:
what's this about?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1262035
in there they tested in a store since the epic 4g touch battery fit into a regular epic 4g, if it would fit into a vibrant. only thing is you have to put the battery in facing inside, and it fits and works 100%
Yeah the Epic 4G batteries fit in our Vibrant's. You can buy knock-off one's (that work well) for 19.99$ US! Here's a thread about it...
http://forum.xda-developers.com/showthread.php?t=1316492
Epic touch battery for the win. I've been rocking it for a few weeks. I was on miui and getting 14-16hrs. I recently went back to froyo and yesterday I got 12hrs off of a 67% charge.
Sent from my SGH-T959 using xda premium
dont know if people have seen this article but i thought it was pretty interesting about the battery stats file not actually needing to be deleted...
http://www.androidcentral.com/wiping-battery-stats-doesnt-improve-battery-life-says-google-engineer
jonen said:
dont know if people have seen this article but i thought it was pretty interesting about the battery stats file not actually needing to be deleted...
http://www.androidcentral.com/wiping-battery-stats-doesnt-improve-battery-life-says-google-engineer
Click to expand...
Click to collapse
Lol one of the biggest flukes in our forum haha.. people will harm their battery to calibrate it and it doesn't even do anything ...
Thank god I only calibrated once
sent from the xda app on my android smartphone.

Droid x2 battery life

My wifes x2 display is using 59% battery. Weve changed the timeout to 30s and brightness down really low. But her. Battery still dies very fast. Its only 2 months old. We ha e disabled bt wifi and gps. Any other tips?
One other question. When her phone dies she cannot plug it in and turn it on or it gets stuck on the motorola logo. Qe have to wait till droid boot animation to plug it in. Any ideas?
Sent from my DROID4 using xda premium
If you plug it in from off do you see the charging screen? Try plugging it in and holding the power button simultaneously if the phone is off.
Is the phone rooted and romd or stock?
Is it running 2.3.4?
Sent from my DROID X2 using xda premium
Its running 2.3.4 rooted but not romd. I had the phone for about a month and had no issues with it. However i never allowed it to die. Shes not a heavy user but my main concern is why the display uses 59% where my d4 uses only 26% on the same settings as hers. Can i unroot the phone in case i have to return it under warranty?
Sent from my DROID4 using xda premium
when the phone dies you need to plug it in and wait until the battery on charge only screen shows at least 10% before the system will, allow you to turn it on
if you have BSR installed tho, as soon as it dies you can plug it in and when BSR comes up you can just choose reboot system now.
and the reason you d4 uses less battery on screen it's because I believe it is an amoled screen, which consumes much, lower power levels than an LCD screen
Sent from my DROID X2 using Tapatalk
Have you tried recalibrating the battery too?
No. How do i do that? Thanks
Sent from my DROID4 using xda premium
First, make sure the battery is completely charged, then boot into custom recovery (BSR). Go to advanced options (towards the bottom of the list) and there should be an option that says 'recalibrate battery'. Once you recalibrate it, reboot back into android. I usually always let my battery run completely out after doing a recalibration before recharging it after a re-cal. If you find on your first discharge after recalibrating that your phone tells you you've only got 20% left and it would normally only last an hour before, depending if it needed the re-cal it may last 2 hours. Those numbers are just hypotheticals. Point is, recalibrating lets android know it's for sure 100% full at the start, but it doesn't necesarily know the end point until it gets there by allowing a full discharge. Also, the lithium batteries our phones use do best when recharged around 15-20%. It's actually bad to let them completely discharge all the time. And if you have multiple batteries and one may be sitting for a while, it's best to store them between 30-40%. Let me know if you need any more clarification.
Im going to try that thank you
Sent from my DROID4 using xda premium
More importantly, if you are already rooted and such, why not run a custom ROM? CM7 and/or Eclipse should give you a good boost in battery life. Running CM7 my standard battery lasts 18-24 hours with light ish usage. And that's with my original battery from when the DX2 first came out. I also have an extended battery I am running right now, but don't have data on that one yet since it's still discharging now. I do know that swapping between batteries of different capacities pisses android off sometimes though lol. Aside from custom roms, there are scripts and apps/software-based mods that can help it significantly too. Namely, wifi vs 3g usage, turning 3g data off when your phone is not being used, etc... I started off with an original DX but VZW gave me a free upgrade to DX2 after my 6th warrantied DX. I miss Rubix's ROM and being able to overclock and undervolt... My DX would last 2+ days sometimes when I had it all dialed in.
Its now my wifes phone. Since she already has had time getting used to stock i doubt she'll let me put a rom on it lol. But ill try
Sent from my DROID4 using xda premium
Well fortunately you've got a Blur-based and AOSP-based option for it. I know what you mean though, my gf likes her Sense-based UI, but had to give it up for a semi-funtioning Eris. I think she is getting a Bionic sooner than later... HTC is garbage.
Maleko48 said:
First, make sure the battery is completely charged, then boot into custom recovery (BSR). Go to advanced options (towards the bottom of the list) and there should be an option that says 'recalibrate battery'. Once you recalibrate it, reboot back into android. I usually always let my battery run completely out after doing a recalibration before recharging it after a re-cal. If you find on your first discharge after recalibrating that your phone tells you you've only got 20% left and it would normally only last an hour before, depending if it needed the re-cal it may last 2 hours. Those numbers are just hypotheticals. Point is, recalibrating lets android know it's for sure 100% full at the start, but it doesn't necesarily know the end point until it gets there by allowing a full discharge. Also, the lithium batteries our phones use do best when recharged around 15-20%. It's actually bad to let them completely discharge all the time. And if you have multiple batteries and one may be sitting for a while, it's best to store them between 30-40%. Let me know if you need any more clarification.
Click to expand...
Click to collapse
Or you can download the app battery calibrator (haar a red Android as the pic) and follow the directions
Sent from my MB870 using xda premium
letting your battery die completely is not recommended no matter what you've been Told
Li-on batteries were designed to last longer when you don't let it die completely
start charging around 15%-10%, 5 is pushing it cuz its most likely gonna shut down before you see 5, trust me, it's bad for the life of tour battery to let it drain completely, just Google Li-on battery life, recommendations and u can read for yourself lol
ashclepdia said:
letting your battery die completely is not recommended no matter what you've been Told
Li-on batteries were designed to last longer when you don't let it die completely
start charging around 15%-10%, 5 is pushing it cuz its most likely gonna shut down before you see 5, trust me, it's bad for the life of tour battery to let it drain completely, just Google Li-on battery life, recommendations and u can read for yourself lol
Click to expand...
Click to collapse
Yeah I know you're not *supposed* to let them discharge all the way but sometimes you have to and sometimes it just happens. For instance, my extended battery that I just did a re-cal on the other day has been sitting at 1% for the past few hours and is currently reading 1day 12 hours of uptime. (I shut it off the other night though and it is still discharging from its initial charge that I did the re-cal on.) So if I would have recharged it at 5% or whatever, I would be losing a decent chunk of available battery because android thought it was empty when it really wasn't, thus skewing the battery's voltage window.
Maleko48 said:
Yeah I know you're not *supposed* to let them discharge all the way but sometimes you have to and sometimes it just happens. For instance, my extended battery that I just did a re-cal on the other day has been sitting at 1% for the past few hours and is currently reading 1day 12 hours of uptime. (I shut it off the other night though and it is still discharging from its initial charge that I did the re-cal on.) So if I would have recharged it at 5% or whatever, I would be losing a decent chunk of available battery because android thought it was empty when it really wasn't, thus skewing the battery's voltage window.
Click to expand...
Click to collapse
that will only happen with extended batteries or one of those "Chinese", aftermarket batteries
regardless, battery life of Li-on batteries will decrease from letting it completely discharge, the more times you do it, the less your battery health will be.(BTW when do you "have to" let it discharge completely? , I'm not "calling you out or trying to "make you look stupid" or anything, I'm just curious what you meant by that?)
when I say 15-5% don't look at it as when Android reports that percentage, the x2 will, NEVER show an extended battery percentage correctly no matter how many times you "calibrate" that's just how it goes, it doesn't realize there is a higher capacity battery in the device larger than 1500mah, what you wanna do is use a battery voltage widget to monitor battery left, when it starts to get around 3500mV is when you are gonna want to charge I believe, (I think that 3200 is completely dead, and 4200 is topped off)
also,, wiping battery stats is a useless practice, not long ago I believe a Google developer wrote about why it's useless, apparently battery stats only has to do with the battery use settings stats about which apps have used which amount of battery. the battery stats gets reset/wiped EVERY time you get to a near fill-full charge (hence why the battery use graph resets itself when u almost fully charged, if you stop charging around 60-70% it wont reset)
reference:: http://rootzwiki.com/_/articles/wiping-battery-stats-is-pointless-says-google-r316
ashclepdia said:
that will only happen with extended batteries or one of those "Chinese", aftermarket batteries
regardless, battery life of Li-on batteries will decrease from letting it completely discharge, the more times you do it, the less your battery health will be.(BTW when do you "have to" let it discharge completely? , I'm not "calling you out or trying to "make you look stupid" or anything, I'm just curious what you meant by that?)
when I say 15-5% don't look at it as when Android reports that percentage, the x2 will, NEVER show an extended battery percentage correctly no matter how many times you "calibrate" that's just how it goes, it doesn't realize there is a higher capacity battery in the device larger than 1500mah, what you wanna do is use a battery voltage widget to monitor battery left, when it starts to get around 3500mV is when you are gonna want to charge I believe, (I think that 3200 is completely dead, and 4200 is topped off)
also,, wiping battery stats is a useless practice, not long ago I believe a Google developer wrote about why it's useless, apparently battery stats only has to do with the battery use settings stats about which apps have used which amount of battery. the battery stats gets reset/wiped EVERY time you get to a near fill-full charge (hence why the battery use graph resets itself when u almost fully charged, if you stop charging around 60-70% it wont reset)
reference:: http://rootzwiki.com/_/articles/wiping-battery-stats-is-pointless-says-google-r316
Click to expand...
Click to collapse
Thanks for pointing that out. I regularly swap between my standard and extended batteries (both straight from VZW) because I'm always out and about and have used re-cal's to keep the perceived percentages from being skewed since I like to know how much life I have left in my phone so I know if I am gonna be able to find my way home or not, lol. (I ride my bike far and wide.)
I remember reading a while back that every time you un-plug your phone from a full charge that battery bin file gets re-written as 100%. So regardless of what android reports, yes, you will always get to use your battery until it is fully dead, but when swapping between two different capacities of batteries the reported percentages get skewed. And as I mentioned before, more often than not I am far from home on a bicycle in a city I only know a fraction of, and many nights somewhat inebriated, haha. I <3 my android, but it can certainly be a lot of work to keep up with.
Maleko48 said:
Thanks for pointing that out. I regularly swap between my standard and extended batteries (both straight from VZW) because I'm always out and about and have used re-cal's to keep the perceived percentages from being skewed since I like to know how much life I have left in my phone so I know if I am gonna be able to find my way home or not, lol. (I ride my bike far and wide.)
I remember reading a while back that every time you un-plug your phone from a full charge that battery bin file gets re-written as 100%. So regardless of what android reports, yes, you will always get to use your battery until it is fully dead, but when swapping between two different capacities of batteries the reported percentages get skewed. And as I mentioned before, more often than not I am far from home on a bicycle in a city I only know a fraction of, and many nights somewhat inebriated, haha. I <3 my android, but it can certainly be a lot of work to keep up with.
Click to expand...
Click to collapse
trust me, I know exactly what you're talkin bout
except mostly riding buses/trains for mE
I have two standard and one extended, I always use the extend first since it will never report correctly when I'm out, then I switch to the standard ones so when they are running low, I KNOW when they will die lol
same here, wifes x2 battery last 2 days..awesome

[Q] Battery Level Drains Inconsistently

I tried searching this in a number of places. I couldn't find what I was looking for, although it didn't help I had trouble using the right words to search for it with, but here goes.
I'm running CleanROM Reborn 1.1, I love it! Other info is also in my signature. Once I turned on the percentage number for my battery level, I really started to notice this.
The number will stay at a number for awhile sometimes, even when I use it, then other times it will jump several points within a minute. It doesn't drain consistently. Anyone have any insight or suggestions? It's more annoying than anything else. My battery life is alright.
I would've tried wiping battery stats, but I hear that doesn't really do anything.
Thanks.
download Battery Calibration from the Google Play Store, then charge your phone to %100. open the Battery Calibration app and calibrate it. There is also instructions inside the App if my instructions are unclear
Im going to try this but for some reason mine only go to about 96%. Never 100% lately so I am not sure if I should do it then or just leave it charged until it is 100% and hope it gets there.
.Bambino said:
Im going to try this but for some reason mine only go to about 96%. Never 100% lately so I am not sure if I should do it then or just leave it charged until it is 100% and hope it gets there.
Click to expand...
Click to collapse
Not to hijack the thread, but the phone is designed to fully charge and then discharge to 95% and then charge to 100% again, rinse, and repeat. This is to keep the battery from becoming destroyed by overcharging. Maybe that's what you are seeing, Bambino.
Sent from my PG86100
Iceman248 said:
The number will stay at a number for awhile sometimes, even when I use it, then other times it will jump several points within a minute. It doesn't drain consistently. Anyone have any insight or suggestions? It's more annoying than anything else. My battery life is alright.
I would've tried wiping battery stats, but I hear that doesn't really do anything.
Thanks.
Click to expand...
Click to collapse
I've noticed this too on Ics leak roms. It sips power with screen off, then drains quickly when on sometimes and hardly at all other times. Mine just sat at 82% for the past 20 minutes, then dropped to 76% over the past five. I've heard battery calibration is bunk, but I'll try the previously mentioned app and see.
Some roms do not use a percentage because they are so inaccurate and cause the user to obsess
Sent from my PG86100
ICS
MeanRoom-ICS-v18 .... Excellent
S-ON Hboot 1.5 Unlocket Last update 2.17.xx
flash whit 4EXT r3
A little info on batteries
The important thing to remember about Lithium Ion batteries is that when you do charge them, bring them up to full charge before taking them off the charger.
They all have a circuit board in them that remembers a full charge. (If you've every taken one apart you'd see this) When you charge them this chip will restore the amount of power that has drained.
Partially charging them will screw up this function. And screw up the battery.
Deep Cycling is good for them but not all the time. Once a month is good for them.
A good rule of thumb, but not absolutely necessary is to discharge them 50% and then bring them up to a full charge. Obviously this is not always possible when playing video games or watching movies. I always try to leave it on the charger when watching movies in the cradle.
There is an app on the Market called Battery Repair. It makes an attempt to reset this chip on the battery by meticulous monitoring the charge and capacity left in the battery. Running diagnostics and setting the battery to its best state. Its the only one out there that does this.
Battery Calibration app is good if you change roms or batteries alot.
Here is what it does:
Calibration needs to be done after flashing a new ROM, but you can calibrate any time you think your battery is miscalibrated. This program does it by removing the batterystats.bin system file. The OS generates a new clean batterystats file soon, thus any fake information from the previous ROM is removed.
It's suggested, but not necessary, to let the phone fully discharge after calibration, then charged to 100% without break.
The app shows your actual battery status, and only allows you to start the calibration (i.e. removes the file) when it's fully charged, unless you force earlier calibration.
The voltage meter can be useful too. Full charge is around 4200mV.

[Q] Charging issue

Hello!
I am facing,lets say a issue, when charging my L920 on charger and phone is OFF. I put on charger after 2-3 minutes it starts by it self....
Does it to anyone else also? It is normal? I just want it to remain switched off while charging like this, but its not a big deal ofc.
Thanks
It is the normal behaviour of ur phone, so be cool with it. It is not an isssue.
miodrage said:
It is the normal behaviour of ur phone, so be cool with it. It is not an isssue.
Click to expand...
Click to collapse
But isnt it better for phone to charge up while its off? i mean it deffinately has less power consumtion in off state :] so it can charge better ..i guess
Seeing as the phone has a 2 Ah Battery and the charger is 1A, you can recharge your phone in about 2 hours (That's from 0 to 100 with a 100% efficiency, usualy efficiency is lower but you usualy don't let the phone drain to 0 ). The power it drains during that time will probably not affect the charging time to much, you can probably charge it in 2h 15m if it's turned on. In short: The time you would save by charging the device turned off is insignificant.
Liborzbrna said:
But isnt it better for phone to charge up while its off? i mean it deffinately has less power consumtion in off state :] so it can charge better ..i guess
Click to expand...
Click to collapse
This question came up a lot when the WP7 came out (it's not a Nokia-specific issue at all).
The gist of the reasoning is that the phone's charging isn't a "dumb charger" that dumps a bunch of current into the battery and hopes it charges eventually (ideally without exploding). Instead, the phone has an actual charging circuit that tests the battery capacity & incoming current to determine how charged the battery is, and cuts off the current when it's at 100%.
This is actual "software" that runs on the phone's processor, and thus requires that the phone be on for it to work.
You'll get used to it.
Brad.
bpsmicro said:
This question came up a lot when the WP7 came out (it's not a Nokia-specific issue at all).
The gist of the reasoning is that the phone's charging isn't a "dumb charger" that dumps a bunch of current into the battery and hopes it charges eventually (ideally without exploding). Instead, the phone has an actual charging circuit that tests the battery capacity & incoming current to determine how charged the battery is, and cuts off the current when it's at 100%.
This is actual "software" that runs on the phone's processor, and thus requires that the phone be on for it to work.
You'll get used to it.
Brad.
Click to expand...
Click to collapse
Thats one serious answer, something i hoped for. Thx a lot for explanation.

Categories

Resources