Razr doesn't detect sim card and reboot continuously - Motorola Droid RAZR

Hello!!
I´m desperate, only two days with my razr and after the first time I turned off for sleeping, I wake up and the droid looks like doesn´t detect the sim card and reboot after more or less 30 seconds. Boots itself and do the same again and again.
Does anyone know what happens?
Thanks!

Tryholding the Power button and both volume buttons a the same time, you should be able to get into recovery mode, wipe the device from there.

I had a similar issue with my lumia 800. After swearing for two days, it was because of a defective microsim....
Inviato dal mio XT910 usando Tapatalk

talulon said:
Hello!!
I´m desperate, only two days with my razr and after the first time I turned off for sleeping, I wake up and the droid looks like doesn´t detect the sim card and reboot after more or less 30 seconds. Boots itself and do the same again and again.
Does anyone know what happens?
Thanks!
Click to expand...
Click to collapse
Excactly the same thing happened to me, reboots and no SIM, so now it's in the shop.

Try turning wifi off, then reboot. Simcard should be recognised. Its one of a couple of bugs.
Sent from my XT910 using xda premium

Related

my phone won't turn on!

i've had the phone for about 7 days and everything was fine until tonight when i tried to use my phone. the phone won't power on anymore.
i plugged it in for a couple of hours and it still didn't turn on. the battery wasn't low when it died. i also tried holding the volume down button then powering on. I even tried plugging it into the usb. i don't know what else to do.:crying:
is it rooted or unlocked? if so which freegee is it unlocked with? you could always join the irc channel for some help. it may be faster through that
sawdey21 said:
is it rooted or unlocked? if so which freegee is it unlocked with? you could always join the irc channel for some help. it may be faster through that
Click to expand...
Click to collapse
it's completely stock and untouched.
kneemahp said:
i don't know what else to do.:crying:
Click to expand...
Click to collapse
Return it.
Sent from my LG-E970 using Tapatalk 2
My brother actually has a completely stock one and is complaining if the same problem to me. I just told him to return it for a new one. Mine is rooted + unlocked and not suffering from any problems. Possibly a hardware problem or overheating?
My friend just had the same issue this morning,
the phone was very hot and wouldn't turn on.
we tried pressing pwr+voldown and nothing happened. then tried pwr+volup and it then showed the LG log but as soon as we let go of any of the button the logo disappears and nothing else happens.
charging also didn't help
*his phone is un-rooted. So i told him to contact Rogers wireless.
bayardo2001 said:
My friend just had the same issue this morning,
the phone was very hot and wouldn't turn on.
we tried pressing pwr+voldown and nothing happened. then tried pwr+volup and it then showed the LG log but as soon as we let go of any of the button the logo disappears and nothing else happens.
charging also didn't help
*his phone is un-rooted. So i told him to contact Rogers wireless.
Click to expand...
Click to collapse
Sounds like a soft brick. Happened to me a few times. Tell him not to worry. LGNPST would fix this.
Edit: didn't see that it was unrooted. Yeah I think you told him the right thing. That shouldn't happen if he hasn't done anything to his phone.
I have had this happen several times.
If you press (or hold) the power button, do you see a cheap white "battery charging" animation?
I can't say exactly what, or why, it works, but keep at it. I think the magic trick is to hold the power until the LG logo has appeared and the boot animation is about to (or has) started.
Sorry I can't be more specific, but I was panic stricken every time. If this is happening to you, then you understand what I mean.
I hope this helps someone. This phone seems to be full of issues... I'm just hoping the software it's the cause, and not the hardware.
Haraldr Blaatand said:
I have had this happen several times.
...
I hope this helps someone. This phone seems to be full of issues... I'm just hoping the software it's the cause, and not the hardware.
Click to expand...
Click to collapse
Same problem for me, phones stops responding unexpectedly, could be that it's power-off by itself but in order to power-on it I need to press power button for a long time ~30 sec. I was thinking that it's because of SnowJB custom Rom but it seems not, the strange thing that it starts only few days ago and appeas almost every day. May be it's needed to format internal or external SD card to fix it?
romrak said:
Same problem for me, phones stops responding unexpectedly, could be that it's power-off but itself but in order to power-on it I need to press power button for a long time ~30 sec. I was thinking that it's because of SnowJB custom Rom but it seems not, the strange thing that it starts only few days ago and appeas almost every day. May be it's needed to format internal or external SD card to fix it?
Click to expand...
Click to collapse
Yea I have the same issues I tried everything to fix but it always just starts again
Sent from my LG-E970 using xda premium
My LGE971 doesn't turn on
Hello there
My Optimus g E971 doesn't turn on.. it was shut down with low battery ..i tried to put back on charger but it's not charging.
I tried to use different charger , different cable but nothing worked.
I tried pressing volume up/down and power button keys simultaneously but still i got nothing.
There is no lg logo or no back light coming on the screen.
I am confused ..
Plz help guys..
That sounds like you need new battery
Sent from my LG-E970 using xda app-developers app

samsung galaxy tab 10.1 will not power on please heeelllppp!!!! ;(

Hey guys my tab has been working great for weeks iv never dropped it or anything it charges brilliantly, its not rooted and it does not have a custom rom on it as i only use it for work today out of the blue it turned off and will not power on i connected it to the charger and nothing happens iv changed the charger and still nothing happens iv held the power button for 15 seconds plus and that didnt work and finally iv held the power button and touched the screen, still nothing worked
Thanks for the help guys
Oh als
What can i do is their anything i can buy to fix this e.g download jig
Are you on 3.2 or 4.0.4?
Sent from my GT-P7500 using Tapatalk 4
eushaun99 said:
Are you on 3.2 or 4.0.4?
Sent from my GT-P7500 using Tapatalk 4
Click to expand...
Click to collapse
Hi im on 4.0.4
Thanks
Interesting...I have no idea what to do..
Can you try booting into bootloader? Hold power down + power button.
Sent from my GT-P7500 using Tapatalk 4
eushaun99 said:
Interesting...I have no idea what to do..
Can you try booting into bootloader? Hold power down + power button.
Sent from my GT-P7500 using Tapatalk 4
Click to expand...
Click to collapse
That didnt work it seems totally dead but i have read a lot about it online. Will a download jig work?
Thanks for your help matey
I don't know what's that lol. Sorry but I can't help you with it. Given that you're stock and unrooted, you might wanna send it to Samsung to fix it.
Sent from my GT-P7500 using Tapatalk 4
eushaun99 said:
I don't know what's that lol. Sorry but I can't help you with it. Given that you're stock and unrooted, you might wanna send it to Samsung to fix it.
Sent from my GT-P7500 using Tapatalk 4
Click to expand...
Click to collapse
No worrys i think ill change the battery or something haha. Iv got no warranty. A downliad jig forces your device in to download mode to be used with Odin lol
If you find anything else let me know matey i appreciate your help
All depends on what the "deadness " is......
Could be dead dead, or could be screen dead in which case stuff is happening but you can't see anything happening.
If you have already had device connected to a computer that has the appropriate drivers installed (talking windows here) open device manager on the computer then connect the tab and see what, if anything happens and might be detected... That would show tab is working but you cannot see it... If nothing happens immediately once it's plugged in, take a fairly long press on power button and see if anything is detected then. A long press on power button (15 sec+) would put tab in apx mode which actually shows nothing on screen but again device manager would show it (this is used for nv flash). At least this way you'll know if it's dead dead or "just" something else...
Btw eushaun99 is a great and helpful dude here and has my respect but I think he gave you a bum steer via a typo with his button pressing...I think he meant press power button and volume down for boatloader, not "power and power" as he wrote, so that is worth a try also... Am I ok with that eushaun99?
sent from my still superb Google I/O 7510 (xda hd)
stinky73 said:
All depends on what the "deadness " is......
Could be dead dead, or could be screen dead in which case stuff is happening but you can't see anything happening.
If you have already had device connected to a computer that has the appropriate drivers installed (talking windows here) open device manager on the computer then connect the tab and see what, if anything happens and might be detected... That would show tab is working but you cannot see it... If nothing happens immediately once it's plugged in, take a fairly long press on power button and see if anything is detected then. A long press on power button (15 sec+) would put tab in apx mode which actually shows nothing on screen but again device manager would show it (this is used for nv flash). At least this way you'll know if it's dead dead or "just" something else...
Btw eushaun99 is a great and helpful dude here and has my respect but I think he gave you a bum steer via a typo with his button pressing...I think he meant press power button and volume down for boatloader, not "power and power" as he wrote, so that is worth a try also... Am I ok with that eushaun99?
sent from my still superb Google I/O 7510 (xda hd)
Click to expand...
Click to collapse
Thanks, you are also a very helpful person on the Q&A section and definitely have my respect as well. Unfortunately, I can't help this guy so it would be very kind of you to take over from here.
You're right, its volume down, not power down. Oops
Sent from my GT-P7500 using Tapatalk HD
I have same issue too. My GT7500 starts only if I warm it till >45°C using a hairdryer or putting it under the sun (here in Italy very hot). But it's only for a normal boot, not in case of reboot when it goes all fine.
Inviato dal mio GT-P7500 usando Tapatalk 4
5p10ng3r said:
I have same issue too. My GT7500 starts only if I warm it till >45°C using a hairdryer or putting it under the sun (here in Italy very hot). But it's only for a normal boot, not in case of reboot when it goes all fine.
Inviato dal mio GT-P7500 usando Tapatalk 4
Click to expand...
Click to collapse
That sounds to me like the battery is tired, very tired and needs some help to produce current required, or a faulty connection somewhere. Once the tab is running the whole unit would tend to self heat so will reboot ok. Most fails are the opposite and are heating faults which is why someone came up with freezing sprays to track down which circuit comes back to life when cooled. Have you noticed any reduction of time that battery lasts between charges ?
Ciao
sent from my still superb Google I/O 7510 (xda hd)
No, it didn't change. This thing lasts since november and it's very annoying 'cause I have to pay much attention to not shut my tab off, elseway I have to get the hairdryer again and so on...
Inviato dal mio GT-P7500 usando Tapatalk 4
What does it do/not do when it doesn't start? Blank screen? Nothing? Bootloop? Freezes?
sent from my still superb Google I/O 7510 (xda hd)
Nothing at all. I keep the power button while warming the tab and when it decides it's enough it starts with the normal boot screen (samsung galaxy tab etc.)
Inviato dal mio GT-P7500 usando Tapatalk 4
stinky73 said:
All depends on what the "deadness " is......
Could be dead dead, or could be screen dead in which case stuff is happening but you can't see anything happening.
If you have already had device connected to a computer that has the appropriate drivers installed (talking windows here) open device manager on the computer then connect the tab and see what, if anything happens and might be detected... That would show tab is working but you cannot see it... If nothing happens immediately once it's plugged in, take a fairly long press on power button and see if anything is detected then. A long press on power button (15 sec+) would put tab in apx mode which actually shows nothing on screen but again device manager would show it (this is used for nv flash). At least this way you'll know if it's dead dead or "just" something else...
Btw eushaun99 is a great and helpful dude here and has my respect but I think he gave you a bum steer via a typo with his button pressing...I think he meant press power button and volume down for boatloader, not "power and power" as he wrote, so that is worth a try also... Am I ok with that eushaun99?
sent from my still superb Google I/O 7510 (xda hd)
Click to expand...
Click to collapse
Thanks for your help matey and thank you everyone else who's helped iv now sorted it :laugh: :highfive: cheers guys. I had to remove the screen to get to the motherboard then unplug the battery and pop it back in again charged it for 30mins and it sprung to life I have now flashed cm10.2 unofficial build that should sort it only problem was a destroyed the adhesive so I had to buy a load more but hey I should be happy it was nothing like a bead board etc thanks again :silly:
jmar8124 said:
Thanks for your help matey and thank you everyone else who's helped iv now sorted it :laugh: :highfive: cheers guys. I had to remove the screen to get to the motherboard then unplug the battery and pop it back in again charged it for 30mins and it sprung to life I have now flashed cm10.2 unofficial build that should sort it only problem was a destroyed the adhesive so I had to buy a load more but hey I should be happy it was nothing like a bead board etc thanks again :silly:
Click to expand...
Click to collapse
Brilliant!! That's a far quicker way than normal where people drain the battery by taping down the power button to drain battery to achieve reset.... :highfive:
jmar8124 said:
Thanks for your help matey and thank you everyone else who's helped iv now sorted it :laugh: :highfive: cheers guys. I had to remove the screen to get to the motherboard then unplug the battery and pop it back in again charged it for 30mins and it sprung to life I have now flashed cm10.2 unofficial build that should sort it only problem was a destroyed the adhesive so I had to buy a load more but hey I should be happy it was nothing like a bead board etc thanks again :silly:
Click to expand...
Click to collapse
Great!!
I'm too afraid of breaking my tab to remove the battery but maybe I'd have to.
Inviato dal mio GT-P7500 usando Tapatalk 4

Phone is completely unresponsive

Went to restart the phone and now it appears to be completely dead. Won't switch on, and is completely unresponsive to any input: usb, hard reset switch, power etc. I have plugged in the phone to a computer as well and there is no "usb detected" on screen or anything. Is it reasonable to assume that this phone is fully bricked?
Did you try th red boton near the SIM card?
Inviato dal mio HTC One usando Tapatalk 4
danilos2k said:
Did you try th red boton near the SIM card?
Inviato dal mio HTC One usando Tapatalk 4
Click to expand...
Click to collapse
Yep
Try holding the power button for an extended time period. You can also do a ftf stock firmware.
Sebring5 said:
Try holding the power button for an extended time period. You can also do a ftf stock firmware.
Click to expand...
Click to collapse
Holding the button for over a minute does nothing, and the phone is simply not detected by any computer I plug it into. The orange LED doesn't even come on when I plug it into a charger :/
Possible that the battery went completely flat? Try plugging it into an AC wall charger for at least 6 hours and see if anything happens.
liqn7 said:
Possible that the battery went completely flat? Try plugging it into an AC wall charger for at least 6 hours and see if anything happens.
Click to expand...
Click to collapse
I will give it a try, but I remember it being almost completely charged when i restarted it
RokkaMan said:
I will give it a try, but I remember it being almost completely charged when i restarted it
Click to expand...
Click to collapse
Did you find a solution as i think i am stuck in the same situation as you did.
RokkaMan said:
Went to restart the phone and now it appears to be completely dead. Won't switch on, and is completely unresponsive to any input: usb, hard reset switch, power etc. I have plugged in the phone to a computer as well and there is no "usb detected" on screen or anything. Is it reasonable to assume that this phone is fully bricked?
Click to expand...
Click to collapse
My wife's Z went dead during an update via PC Companion (light went out), and it didn't boot or show any life sign.
I used the Sony PC Service (only for PC), restored the phone to the original FW and all went well, nothing was deleted from it. Try it and see...
Sent from my GT-I9300 using Tapatalk 2

[Q] Power button not working when powered down

Hello, I am having problems with my Atrix since I bought it.
It works great, but sometimes it powers down by its own, and then it takes many tries at the power button to get it running back again.
This also happens when I power it down, and sometimes when I connect the USB cable.
I have to repeatedly press the power button until it powers back on. I like the phone, and I really need it, so I would like to know what I can do.
Thanks
Did you try with another battery?
Yes I did, I actually have another Atrix and both batteries work well with that one
Same problem here.
Well I have the same problem with my Atrix too. Hope someone help us
Sounds like a hardware issie, when the phone shut down itself, it is hot?
What happens if when it powers off, you remove the battery, wait about a minute and try again?
Enviado desde mi MB860 usando Tapatalk 2
andresrivas said:
Sounds like a hardware issie, when the phone shut down itself, it is hot?
What happens if when it powers off, you remove the battery, wait about a minute and try again?
Enviado desde mi MB860 usando Tapatalk 2
Click to expand...
Click to collapse
I dismantled the Atrix and found nothing, when I was putting it back together, I tried to power it on to be sure nothing was left unpluged. And it powered immediately. When I finished arming it again, the problem returned, so I assume it has to do with a bad contact.
Anyhow, I ended selling it, and buying another one.

[Q] Please help! Stuck in Bootloop, power button "stuck", no download mode!!

[Q] Please help! Stuck in Bootloop, power button "stuck", no download mode!!
I believe this has to do with the phone thinking the power button is constantly being pressed...
I'm looking for any advice. My s3 suddenly went into a boot loop this morning. It powers on for a few seconds and turns itself back off.. Doing a little research, came across similar issues online caused by the main board going faulty and the phone thinking the power button is constantly being held down.
I know this because I can remove my battery, put it back in, and without even touching any buttons, the phone will attempt to power up.
I'm currently rooted and can't get into download mode for more than 3-5 seconds before it turns itself off. I was only once able to apply the perfect pressure by squeezing the side of the phone which allowed it to boot normally, but about 30 seconds later, the power menu appeared by itself and it turned off a few seconds later.
Has this happened to anyone else?? Anybody know how to go about fixing it??
Inviato dal mio GT-I9300 utilizzando Tapatalk
When you take out the battery, wait for a few seconds before putting it back in. If it turns on automatically then this might be hardware issue and needs repair.
Yes,it turns on automatically...i have disassembled the phone and checked the power buttom and it seems to work right,i can't understand where is the problem
Edit. OK,the problem is that the power buttom is hyper sensitive..can i do something to reduce the sensibility?
Inviato dal mio GT-I9300 utilizzando Tapatalk
Replace the power button, it is worn out.
Sent from my GT-I9300 using Tapatalk
I am having the same problem and just saw this thread. Thanks.
Is the power button known for wearing out on the phone? I take good care of my s3 afaik. Maybe it's time for a new phone.... =(
grungypoo said:
I am having the same problem and just saw this thread. Thanks.
Is the power button known for wearing out on the phone? I take good care of my s3 afaik. Maybe it's time for a new phone.... =(
Click to expand...
Click to collapse
Happens from time to time. Maybe if it dropped or been pressed too many times.

Categories

Resources