Related
.. my apologies if this not the appropriate place to post this, but I need help..the little battery door/flap that clips into place which holds the actual battery in place and covers the SIM card (not the black battery cover/antenna) has broken!!.. Now whenever the phone drops or is handled rough enough to cause the battery cover/antenna to come off, the battery slides out of place and the phone turns off.. this happens multiple times throughout the day..i'm ready to throw this phone into the far reaches of this galaxy to say the least... if thats not bad enough, the little chrome peice that surrounds the sensor part of the optical trackpad on the front of the phone has fallen out .. it really takes away from the beauty of the phone!.. any idea where I can find replacement parts for these???.. used or new, it doesn't matter ... If ANYONE can help me i'd be indebted to you for ever!!!
Try contacting HTC.. They make the phones and they should know.. And btw.. Handle your phone a little more careful..
Sent from my Legend using XDA App
Damn, i've always been afraid of that happening expirimenting and having to remove the battery frequently. Don't know anything to help you, sorry
I have the same broken part. Been looking around for this part for a while with no luck. HTC want £44 to replace it, only by sending it in for a repair. They will not sell me the part and I cannot find it anywhere.
I will keep an eye on this thread for more suggestions.
Tape? Although it would have to stick to the aluminum unibody. See if it works! My head's imagery seems like it could.
Yes, my Legend is basically held together with tape. Without it, the battery cover comes of very easily. It's been like this for about 6 weeks now.
I've also been in to my local Vodafone shop to see what they say. They will not repair it as it's a moving part.
Buy your Legend a silicone or rubber case. That should prevent black cover from falling off.
Sent from my HTC Legend
why don't u fill the gap between the black part and ur battery with a soft rubber?
i think it'll solve ur problem
I want this part too. The center clip mechanism has failed due to taking the cover off regularly.
Oh my goodness, I should stop switching SIMs every now and then. I'm scared, actually.
branch8 said:
Damn, i've always been afraid of that happening expirimenting and having to remove the battery frequently. Don't know anything to help you, sorry
Click to expand...
Click to collapse
I was thinking of placing a secundairy antenna on that part, so you would stil have an small antena if the lid is missing. or maybe even better reception.
If you still have problems with the battery cover/flap, here's what i did on my legend: Take out the battery, look inside the battery compartment, you'll see the four battery contacts/pins, and right next to them you'll see there is a small black square rubber, glued to a metal spring underneath. The spring is heavily glued to the chassis/plastic body. I took a small (but strong) set of tweezers, and pulled the thing off the phone (the spring + the small rubber attached to it), and my phone works perfectly now, with the broken flap. The thing is that the spring is actually pushing the battery out, for "easier" removal, thus making the battery loose contact/fall out on every shake/impact.
I think that the design of this part is the worst about the legend. On mine I have experienced that the grip is weaker and weaker, and now comes off quite easily (unintended).
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
My screen registers a touch from my S Pen when it is about a half inch away from the screen. This makes it difficult to take a note or to even just use the pen. From my understanding it is because the white tip is stuck in a little bit. I tried to contact Samsung and the only thing they told me to do was a factory reset or take it to an AT&T store. The problem is I go to school in Iowa and the closest AT&T store is 60 miles away. Any suggestions on fixing the S Pen?
You are correct in thinking the stylus tip is pushed in too far to create an "always on" effect. It is possible the stylus is simply defective, but there's one way to find out.
A lot of styluses come with a tool for removing and/or replacing the tip, as a stylus tip generally wears out after several years.
WHAT TO DO: Take a pair of tweezers and gently clamp down on the nub where it meets the stylus pen, then try to pull it out a little. DO NOT GRAB OR CLAMP THE NUB FROM THE TIP OR OTHERWISE SQUEEZE THE VERY TIP or you could misshape the tip and then it could scratch your screen over time. All you need to do is pull the nub out a little without accidentally compromising the tip that meets the screen.
After you pull the tip out a little (or all the way), push in gently but firm with your fingers to re-seat the nub.
Here's a video: http://www.youtube.com/watch?v=aertF9yb6n0
You can also try the aluminum tape method to resolve the screen interference issue, it's worked with my 2 s-pens that had the same symptom.
I dropped my S Pen in the toilet......
Had this problem after washing it until it dried. I do seem to still have the same problem occasionally though.
ny2k1012 said:
My screen registers a touch from my S Pen when it is about a half inch away from the screen. This makes it difficult to take a note or to even just use the pen. From my understanding it is because the white tip is stuck in a little bit. I tried to contact Samsung and the only thing they told me to do was a factory reset or take it to an AT&T store. The problem is I go to school in Iowa and the closest AT&T store is 60 miles away. Any suggestions on fixing the S Pen?
Click to expand...
Click to collapse
The tip doesn't move much, it's almost impossible to see unless you're looking at it pressing into a flat surface from the side. It might move .5 to 1mm at most.
Anyway, lots of threads on this already...
UPDATE: So, the digitizer I bought developed a massive dead zone. I already contacted the amazon store I bought it from, they're replacing it for me. Why does this matter? Because now I get to update this post with pictures/video! So, yeah, I guess this guide should get a lot more helpful soon.
Update 2: Ok, so, I don't even know how to express my anger and frustration. This girl at work shoved my phone out of my hands and into the leg of a table, completely destroying my phone. So, yeah, sorry, I guess I won't be updating with pictures/video, because the amazon store isn't going to take the screen back now.
Yo, guys. If anyone noticed that I was gone, I'm flattered, since I don't post a lot. But yeah, I havent had my Optimus G in about a month, so I havent been on this forum. In that time, I went through my Second Motorola Atrix HD, a broken Galaxy S3, and even lived through Google Voice on my computer. It's an extremely long story, and kind of ridiculous, so I'll spare the details.
HOWEVER, I did finally just buy a replacement Digitizer and LCD screen, and successfully installed it, and I want to share tips for anyone doing it themselves.
When removing the back, after you've removed torx screws, start prying the back off from in between where the Sim card and MicroSD go. Where the back of the phone and the chassis of the phone are separate is much more obvious in that cavity, PLUS dents/dings from jamming a screwdriver in there wont be noticeable when you put the bay cover back on.
Don't force anything off. Make sure you've removed every screw, unclipped every clip, and removed ribbons from everything you're trying to take off.
Removing the battery is tricky. Be careful not to deform it too much, cause that's dangerous. But there are 2 strips of double sided tape running horizontally beneath the battery. Try to get something between the top one and the battery, then carefully pull the battery off the second strip with your hands. sticking too much stuff beneath it to pry it up is going to cause some trouble, so lifting it with your fingers might be better.
Remove the motherboard. detatch all the ribbons, antennae, everything, then pull up from the left, then slide left and out. This is how I got it out with the least resistance, but there is no science to it. If you've gotten this far, you can figure out how to pull it out without breaking it in half.
Components that need to be removed before LCD+Digitizer removal:
Motherboard
Battery
Camera
Just put them off to the side, you don't want them damaged during the next part.
WARNING! If you plan on saving your LCD screen, DO NOT DO THIS. The high heat will cook your screen and make it unusable. Only do this to remove a broken or unsavable Digitizer+LCD.
Alright, now pull out the heat gun. Alternatively, you can do what I did, and use a hair dryer. Not even kidding, this will work fine, and will be hilarious when you tell your friends about it.
On a high heat, start heating the screen. If you're using a heat gun, just do your thing, you know how it works. Hair dryer folks, keep the dryer very low to the phone, low enough to feel the dryer being pushed up by the air, holding it just high enough so it sort of hovers. (You'll know what I mean when you try it. If you don't, just keep it about half an inch off the phone.) Move the dryer along the edges of the screen, all the way around, thats where the glue is. It should heat up pretty fast.
Using your pry tool, start at the speaker grill and pry all the way around the phone. lifting just slightly upwards. If it's not extremely easy, apply more heat. Work all the way around, then pull the screen off. Be careful, it's likely you'll shatter the screen even more at this part if you're not careful. User Bozwell had an excellent suggestion (post 4), cover your screen in tape, then begin separating the screen to keep from getting glass everywhere. Great idea, Boz!
Alright, so from here on out, it's just reassembling your phone correctly. Piece o cake.
Firstly, put your new screen in. If it came with adhesive, it's up to you if you want to apply it now. I'd think you probably have to, but up to you.
If you're like me, and no adhesive was provided, hold off on doing anything for now. Just put the screen in the hole, and thread the ribbons through.
The motherboard lines up with some contacts on the chassis in a few places, but most importantly, there is a connection on the top left corner of the body, and the UNDERSIDE of the motherboard that needs to be made. I believe it's proximity sensor, but not sure. It's very difficult to tell if its attached, but look at what I'm describing, and try your best to mate them.
Don't forget ANY cables. Like, that's pretty obvious, but even when you're sure you didnt forget any, check again. The camera's ribbon is underneath the screen's, don't forget that one. I reassebled the whole thing, everything was working perfectly, except I no longer had any mobile connection. I couldn't imagine what I'd broken, since that's a whole different area, but going to phone status and checking my signal strength revealed I forgot to reconnect the white antennae (status showed my signal at -200,000 dbm). So, double check, because the more often you have to reopen your phone, the more flimsy it's going to get.
Alright, screw the plastic shielding back on, reconnect your battery, then flip the phone to be face up. Power it on, test the screen to make sure it's functional. If all is well, power off and glue the screen in. What I did, and I welcome anyone to tell me a better glue type or method, is plain ol Super glue along all the edges where the old glue was. Press it in, flip it over, and while it's drying, finish reassembling the phone (should just be make sure everything is screwed in inside, then put back glass back on.
If your screen wasn't functional, I guess try to get it replaced by whoever you bought it from, and leave your phone disassembled for when it gets to your house.
Alright, that's pretty much the thick and thin of it, it genuinely isn't that hard of a replacement. I've done a number of digitizer/lcd replacements, not bad at all. I hope this helped anyone stuck or wondering about anything. This video can be used as a rough example, but it goes really fast.
Good Luck!
replacement of lcd/digitzer
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
gruiz3 said:
the removal was a nightmare for me. It was hilarious when the glass cracked it was exploding into a million little bitty pieces. I didnt use much heat, and there lied my problem. But yeah mine cracked in a way that it was completely unresponsive.
Click to expand...
Click to collapse
Haha that's crazy, it bothers me how fragile this phone seems to be.
To keep the glass shards from going everywhere try covering the screen in tape before you start.
bozwell said:
To keep the glass shards from going everywhere try covering the screen in tape before you start.
Click to expand...
Click to collapse
Great idea, OP updated!
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
MoFoQ said:
So, what would I do if the screen itself is ok and it's just the glass (and digitizer) that is broken?
Click to expand...
Click to collapse
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
ripin150 said:
You'll need a real heat gun, I think. You'll have to find a heat just hot enough to soften the glue, but not cook your lcd. Hair dryer method might work if you are extremely careful and very quick, but not sure exactly what the best method would be. Sorry
Click to expand...
Click to collapse
I figured...though I've been eye-ing using the screen+digitizer+front housing if and when they get back into stock.
(digitizer only is also out-of-stock)
Hey guys. Just thought I'd give you a headsup here.
I've had a bunch of phones (listed in my signature), but I have never encountered this before.
The other day as I was gaming I kept bumping my hand into my phone over and over. This has never happened before, despite that I normally put it on the far corner of the mouse surface to have it readily accessible. I didn't think any of it first and just moved it up, thinking that maybe I accidentally moved the surface or such, causing the phone to move.
Then in some downtime in the gaming I looked down and realized the phone was moving. My god! There was practically zero friction! My phone was just gently gliding around the mouse surface, lolygaging about. I had a little fun with it, poking the phone to make it slide a different direction and making my cat freak out with it.
I then put it to the side on the table, thinking that my hardshell mouse surface was probably so low friction that it made the phone slide around. But the same thing happened on my wooden desk. It kept sliding around. Then I turned it over with the display upwards, and it was fine.
This morning same thing happened, and it actuall slid off the edge of my kitchen counter (marble) and into the floor! The phone is fine, by some kind of miracle, but I was surprised it managed to pick up enough speed to not get stuck on the edge of the counter. I tried pouring some water on the counter to see if it was leaning, but nope. Flat on both according to the water and a spirit level.
My only conclusion is that the phone is so flat all around, including bezels, that it creates a small air bubble underneith it, which it then slides on. The feeling is that of an air cushion as well.
I realize most people probably dont put it display down, but if you do, be aware of this. My phone almost jumped to its death by it, surviving only by a guardian angel. I thought about it and decided it was a big enough risk to give people the headsup.
Stay safe G2'rs!
SweStag said:
Hey guys. Just thought I'd give you a headsup here.
Click to expand...
Click to collapse
Good to know. Where I am, they only sell cases for QuickWindow (last I checked). I bought one, but it is taking a while to get used to holding the phone when talking since I can't wrap my fingers around the phone.
I was considering taking it off, but that notion is no longer in my head thanks to your post. BTW, you should post some vid on messing with the cat!
Hah, I just might. She's like.. "Oh, looks like fun", pokes it a bit, notices how it doesn't act as expected and is all like "BLAARGH" smashing it around and trying to kill it. xD
The screen is very silky, compared to my S3, Atrix, Kindle and my friends HTC 8S.
Sent from my LG-D802 using Tapatalk 4
So what you're saying is glass is slippery? In other news the sun will set in the west tonight. Just kidding, but I wouldn't ever put my phone face down without some type of case to keep the glass from contacting anything bad. The Nexus 4 was extremely slippery, the way LG is making curved edges on the screens doesn't help in that regard.
Well, I've learnt to put mine screen down to protect it from things falling on it. The nature of my job means things may well fall on it. I use a screen protector film anyways.
And yes, glass can be slippery but doesn't have to be. None of my other phones have had this kind of behavior, probably due to them having a slight lift from the frame, keeping the glass off the actual surface.
Regardless, for some its a non-issue, but for those that it might affect, I thought I'd share.
Hoverboards are next. I can feel it.
Sent from a van down by the river using my AT&T LG G2 and Tapatalk 4.
SweStag said:
Regardless, for some its a non-issue, but for those that it might affect, I thought I'd share.
Click to expand...
Click to collapse
This is a good point. I usually flip my phone screen down at night so the notifications LED isn't lighting up the room. Needless to say, my dog wasn't very amused when the phone slid off the nightstand and woke her up.
jmacdonald19 said:
Hoverboards are next. I can feel it.
Sent from a van down by the river using my AT&T LG G2 and Tapatalk 4.
Click to expand...
Click to collapse
I lol'd at your post as well as your signature.
edl415 said:
This is a good point. I usually flip my phone screen down at night so the notifications LED isn't lighting up the room. Needless to say, my dog wasn't very amused when the phone slid off the nightstand and woke her up.
Click to expand...
Click to collapse
So I'm not alone! Lets hope someone saves a screen at least.
thanks for the headsup, on low friction surfaces things slide.
You check if you need to level your furniture so gravity doesnt make things slide
a case would help as well
Pretty common occurence also on the shiny plastic Samsung devices Even iPhones suffer from it.
Again, it's most likely due to the curved glass edge of the LG screen. I prefer the curved glass, and my best suggestion to those that need to put their phone face down due to work hazards should probably put a case on the phone. If heavy things have a chance of falling on it, it's probably a good idea the phone is either in a case or in your pocket. Just friendly advice so please don't take it as otherwise.
I had the GNex before so wasnt an issue...but day 1 with the phone. Put it face down on the counter top like I had always done before and got in the shower. My wife comes in and all the sudden.....BAM! My phone hits the ground. (thankfully on the mat!) She said she saw it kinda "gliding" towards the edge. Low and behold, this thing almost floats face down on any slick surface. I almost never put it face down anymore...lesson learned.