Hi
I have a Samsung Galaxy S2 I9100G in dead condition when i connect to pc it ask OPAM4430 driver. and i have installed but i cannot active it to download mode even i cannot see anything on LCD screen.
any on please help me to flash this phone with any rom.
Regards.
First of all, what did you do first? What I can say is try do this when phone is off. Power, volume up and home button at same time. See if this works. If you get, try selecturing wipe and see if the full wipe solve the problem.
Sent from my Galaxy Tab 8.9 using Tapatalk HD
A phone wont just die like that.If you did something to it then give some details althought it sounds like a kernel problem.The wipe idea is a good one,probably your best bet as you wont be able to use odin.Do a full wipe.
Boot to recovery (power+home+vol up)
Wipe cache partitiion,go to advanced and wipe dalvik cache (go back)
go to Mounts and Storage and format System,Cache,Data(go back)
Factory reset and reboot.If you get a bootloop then pull the battery,put it back in and reboot.
If you cant get to recovery or download you could try fussdownloader but im not sure if it works with the G model.Anyway the drivers can usually be found seperatelly and installed if you google for them but may or may noy not help.Worth a shot.
actually i got this phone from my friend and he say some one try to Nuke it i don't know how.and i cannot go to recovery mode by pressing volume down home key and power key also it not detecting on Odin
Regards.
pmmali said:
actually i got this phone from my friend and he say some one try to Nuke it i don't know how.and i cannot go to recovery mode by pressing volume down home key and power key also it not detecting on Odin
Regards.
Click to expand...
Click to collapse
Sounds to me like someone made a mistake trying to flash it and put the wrong firmware,or worse,the wrong kernel in Odin.Most people brick their i9100G phones with i9100 firmware.they are not compatable.The only thing I can suggest is try and find out if there is a RiffBox JTag service available for the G-series.It is for most other models.What it does is wipes and repairs the motherboard and bootloader.Ive had one done on an i9000 for 35 euros so its not an expensive job.Just need to find out if its available for your device.Ill leave a link below,Its an old one,but its a list of places world wide where they do it.If you dont see one close to you then use the page and google to search for one closer to your location.since this page was released the JTag has become more available in more areas.so you should find one close to you.good luck.
http://www.jtagbox.com/riff-jtag-bo...-bricked-phone-riff-box-owners-list/#comments
thank you very much for your clear reply and ill try and inform you.
Any one can give the correct jtaf pinout for i9100g
same problem for me, friend gived me i9100g bad flashed with i9100,
now it is dead and ask for omap4330 drivers when connected to pc.
It not go in download mode and not go in recovery.
I'm triyng to flash boot with riff but riff not detect it
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
here are pinouts for @pmmali
how did you solder it??? its very tiny....
Lol.....VERY steady hand, a fine pointed soldering iron and a magnifying glass are all necessities.
Word of caution.....don't jtag if you want to send the phone to Samsung (under warranty).....they'll see that some "unofficial rework" has taken place and deny liability for warranty repair on that basis. ....
Sent from my Rooted, De bloated Stock JB powered S2 via PhilZ kernel and Tapatalk 2....
Related
Salam,,,,
i just bought my galaxy s ii yesterday with stock 2.3.4
i think that i followed all steps for "rooting thing"
after load "CF-Root-SGS2_XX_OXA_KG1-v4.1-CWM4" in Odi3 v1.85
when i clicked start it says pass, but the last message in the box it says: Removed!!
then i got the yellow triangle, i tried to do the same step again and again, and sometimes load "KERNEL_I9100XXKG2_CL375027_REV02_user_low_ship.tar.md5"
i cant start my phone!!
help please
my apologies
now i got this problem
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Simple to remove yellow triangle: USB Jig
Second problem, try holding down Power + Vol Down + Home buttons together when the phone is off, until you see a verification popup saying if you want to continue to flashing a custom ROM. Then try reflashing your ROM or kernel.
well, in my country there is no USB jig unfortunately
second i got this problem in my second replay (look image)
there is no use when holding power+home+volume down or up
the same problem appear to me
thanks for your help
I doesn't matter if it's not in your country. Order one here:
http://usbjig.com/
Did you enable any of the checkboxes that were disabled when you started Odin?
Like "Repartition" or "Flash Bootloader" or any of those?
yes, all three was checked when i used PIT, PDA, PHONE, and CSC
There we are. The Galaxy S 2 does not need a pit file, you probably got a pit file for a Samsung Galaxy S.
<Warning information heard from other users>
In another big Android board is a discussion going on that flashing a pit file can fry the mainboard + battery as it will use wrong settings (the settings for the Galaxy S) and apply a too high voltage.
</Warning information heard from other users>
From my experience in that case even the jig does not work anymore (you could try it anyways) so you might either need to send it to Samsung or find somebody with a JTAG (won't help if the mainboard gets damaged).
@prodygee
i hope it doesnt take long time in delivery
ohh, dont tell me that the board is damaged
i didnt spent 24h yet!!!!
DBGT_87 said:
ohh, dont tell me that the board is damaged
i didnt spent 24h yet!!!!
Click to expand...
Click to collapse
Nah, as I said, those are just reports from other users I couldn't verify (I'm not gonna flash a pit file just for the sake of testing!) so you should try the jig anyways, because it's not expensive and does the trick in many cases.
However if those user claims are correct not even a JTAG could help but let's just hope the best for the moment, there's no point in being scared beforehand.
I wish you luck and please tell us if the jig worked!
If you want to remove the yellow triangle and you don't have a jig it will be simple..
Flash Cf-Root
Flash stock kernel (cwm for cf root will remain)
Unzip the Cf root you falshed earlier until you get zImage and don't rename it
Open cwm
Choose flash kernel
Select the zImage you extracted and flash
After that there will be no yellow triangle after boot
Sent from my GT-I9100 using xda premium
@ephraim033
my friend i cant go to download mode anymore
how much do you think it cost when the board is damage more than $200?
i will try warrant company, then try jig
I see.. Why don't you take it to damsung service center and make a story that you updated through kies then kies broke your device.. Atleast try the service center because it's free, but if all else fails you can try jtag
Sent from my GT-I9100 using xda premium
oh man, i just take it to warranty company, they told that they will try to update the software (i think it wont work) otherwise they will give a new one!!
Why are you flashing anything without not knowing what your doing?!
Sent from my GT-I9100 using Tapatalk
they gave me a new, told me that your problem cannot be fixed
they will send the phone to Samsung!!
Hi
I will try and list everything i can i suspect i will not be able to fix this but thought someone might have some insight as to how it happened.
Whats Wrong:
No signs of life, no boot screen, no recovery mode and no download mode. I have held down the reverent buttons for over a min and i get no response from the phone. Have checked its not just a flat battery, its been charging for 2 hours and same response whether plugged into charger or not.
What I was doing:
The Phone was the stock Rom that I had rooted (I use the orange signal boost app at home, and didn't want to lose it.) I decided to change the menu icons for my apps to a matching set and was using APK editor to do that. Knowing that messing with the signal boost app could mess it up I created a backup of the Rom using CWM before starting and then tried changing the icon and re-installing signal boost. It failed and the app would not run when I tried to re-install the original. So I booted into recovery mode and told CWM to recover from the backup i had created. I left the phone and when i came back it was blank and has been ever since.
Phone details
Orange Uk branded i9100p
running android 4.0.4 stock (rooted)
As I said I doubt this is an easy fix but if anyone can give me a hand i would be eternally grateful. Failing that is someone can shed some light on what went wrong so i can avoid it in the future that would be great to.
Thanks
Tom0468 said:
Hi
I will try and list everything i can i suspect i will not be able to fix this but thought someone might have some insight as to how it happened.
Whats Wrong:
No signs of life, no boot screen, no recovery mode and no download mode. I have held down the reverent buttons for over a min and i get no response from the phone. Have checked its not just a flat battery, its been charging for 2 hours and same response whether plugged into charger or not.
What I was doing:
The Phone was the stock Rom that I had rooted (I use the orange signal boost app at home, and didn't want to lose it.) I decided to change the menu icons for my apps to a matching set and was using APK editor to do that. Knowing that messing with the signal boost app could mess it up I created a backup of the Rom using CWM before starting and then tried changing the icon and re-installing signal boost. It failed and the app would not run when I tried to re-install the original. So I booted into recovery mode and told CWM to recover from the backup i had created. I left the phone and when i came back it was blank and has been ever since.
Phone details
Orange Uk branded i9100p
running android 4.0.4 stock (rooted)
As I said I doubt this is an easy fix but if anyone can give me a hand i would be eternally grateful. Failing that is someone can shed some light on what went wrong so i can avoid it in the future that would be great to.
Thanks
Click to expand...
Click to collapse
is your phone in warranty ?
also does it show any display wen u plug it on charging
also wen u put it for chargin leave it from 30 to 60 mins and check if the area near the camera is getting hot , if its gettin hot then u have hard bricked ur phone
if ur phone is in warranty u can head to service center for replacement jus don tell them what u ver actually tryin to do
or if its not in warranty then u can try getting ur phone to ur nearest jtaq center
Brickbug??
"To err is human, to forgive is divine"
Sent from my SGS II
try a USB jig.. does it work??
Listen to neo there.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from the little guy
I've been searching XDA and Google for months now and I haven't found anyone else with this precise issue. I'm very tech savvy, but this is just beyond me! What say you? Will you help me in my quest to diagnose my device and possibly find a cure?
Listed below is what occurs when the USB Cable is connected, either via PC or the Wall.
While USB Cable is disconnected:
Pressing or holding any of the buttons, together or individually, does absolutely nothing. (But the battery can't be dead. I've had the thing on charge all night!)
When USB Cable is connected:
http://youtu.be/J8FJSo_S7cQ
Without pressing anything, the device powers on into download mode and continues to reboot itself every few minutes.
Holding the power button (or all buttons together) reboots it back into download mode to repeat what I just described above.
Pressing any/all buttons at this point does nothing.
When I disconnect the USB Cable from the device while in Download Mode, the device shuts off after about 20 seconds.
I have seen this on occasion, but nothing different happens:
(I'm aware this means forced download mode.)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I'm able to use Odin completely normally and flash anything successfully as well. Yet it just reboots back into download mode. And if I leave it alone while connected to my PC with Odin up, this is what it looks like:
I've "successfully" installed Stock ROM, Kernel and PIT files. Nothing changes! I've also tried one-click unsoftbricker, heimdal, calling it names, begging it to work. Am I crazy or...is this thing done for?
Have you tried repartitioning it?
By clicking that check box in Odin? Yes.
Ah, you must've hardbricked your Galaxy.
http://forum.xda-developers.com/showthread.php?t=1496360 < See if anything in that topic helps you.
You need to flash a ROM that has boot loaders in it...
When you use the unbrickable resurector, it flashes a boot loader that always boots to download mode. From download mode, you can flash a FULL rom, that will replace the boot loader. Then it will boot normally.
TheKryptonite said:
Ah, you must've hardbricked your Galaxy.
http://forum.xda-developers.com/showthread.php?t=1496360 < See if anything in that topic helps you.
Click to expand...
Click to collapse
Thanks, I've been suspecting hard brick. I've seen that thread before, it could really use some reorganizing. I can barely follow it.
Meticulus said:
You need to flash a ROM that has boot loaders in it...
Click to expand...
Click to collapse
That would make sense but which ROMs would those be?
This is a Russian ROM but it should have boot loaders.
http://www.4shared.com/zip/vxHoJ8E0/G70JKKE3_STOK_222RU_.html
Let me know how it goes...
Downloading now. I'll have to try it tomorrow on spare time. Really hoping this works. Thanks for giving me some hope, I really thought this thing was done for!
It's not hard bricked... that ROM will restore it. But after you flash that rom , you'll need to flash a different Rom for your region...
Meticulus said:
It's not hard bricked... that ROM will restore it. But after you flash that rom , you'll need to flash a different Rom for your region...
Click to expand...
Click to collapse
I never even heard of a "Full" ROM before. The problem I was having was apparently my bootloader - or lack-there-of.
You saved my Galaxy Player's life! Thank you very much!
I'm happy to say that this case is closed!
I am going to favorite this thread. You never know when you'll need some good info like this.
Ironically, my GP just managed to softbrick -_- I may be f'd.
Edit: Thankfully, I managed to fix it. Whew!
Hello, I have a little question, recently a friend told me if I can fix his i9100, cause "it remains at logo"
My surprise was that the phone doesnt even charge, when I plug it to the power, a battery that aparently is loading apears, for 2 segs, and then the screen turn off, and then the battery icon agains, and remains in a infinite loop but wont charge
Someone have this problem and knows how to repair it? I wish the problem isnt hardware :/
This is the exact icon i say:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks in advance Guys!
ManaSV93 said:
Hello, I have a little question, recently a friend told me if I can fix his i9100, cause "it remains at logo"
My surprise was that the phone doesnt even charge, when I plug it to the power, a battery that aparently is loading apears, for 2 segs, and then the screen turn off, and then the battery icon agains, and remains in a infinite loop but wont charge
Someone have this problem and knows how to repair it? I wish the problem isnt hardware :/
This is the exact icon i say:
Thanks in advance Guys!
Click to expand...
Click to collapse
could need a new battery or new usb flex cable (charger port)
even more, perhaps..there is a "bootloop" problem that explained this behaviour...please looks for the post, in Development thread, to fix this issue
ko2005pu said:
even more, perhaps..there is a "bootloop" problem that explained this behaviour...please looks for the post, in Development thread, to fix this issue
Click to expand...
Click to collapse
Thank you very much for your answer, it makes me happy that possibly the problem has a fix, but, please, can you link me the fix, i searched before (maybe i didn't search properly) but I didn't found it, please help me, thanks in advance!
You will have to reflash a stock rom using ODIN. Don't worry because there are many guides over the internet. Guide: http://mobilenetworkcomparison.org.uk/tutorials/how-to-restore-the-stock-samsung-galaxy-s2-rom/
Make sure you download the rom for the correct version of phone!
Once you've flashed stock rom, make sure to factory reset and wipe cache partition. (note: don't do this if you are going to flash ics because this might hard brick your device)
gsstudios said:
You will have to reflash a stock rom using ODIN. Don't worry because there are many guides over the internet. Guide: http://mobilenetworkcomparison.org.uk/tutorials/how-to-restore-the-stock-samsung-galaxy-s2-rom/
Make sure you download the rom for the correct version of phone!
Once you've flashed stock rom, make sure to factory reset and wipe cache partition. (note: don't do this if you are going to flash ics because this might hard brick your device)
Click to expand...
Click to collapse
Hello Thanks! I didn't see when you reply!!
The problem is that, I can't even get into download mode, when i press power button, the screen doesn't turn on, the screen turn on until I plug the charger, but only appears the battery icon i put in the first post :/
ManaSV93 said:
Hello Thanks! I didn't see when you reply!!
The problem is that, I can't even get into download mode, when i press power button, the screen doesn't turn on, the screen turn on until I plug the charger, but only appears the battery icon i put in the first post :/
Click to expand...
Click to collapse
Maybe it is a battery problem... Try a new battery.
Tried with a new battery, and same problem :/
Hi i am newbie this forum i have an problem with an android gingerbread isn't booting and didn't vibrate show samsung logo or anything battery charging now show and when i connect to my windows it sounds device connected / disconnected and when on Device manager is "Unknown Device" It's one of seriously problems because maybe android plays with unmount system / partition 4025 MB or something from clockwork recovery now the system cannot be reinstalled , booting into recovery , download or anything and ODIN Didn't show ID / COM .Does this think happened to you press the button / plug in charger and nothing happened .I Also installed Android ADB Driver upon adb devices command it display error no device found I Try to find a way to repair myself without to take the old device to an repair shop to replace the android piece memory that i don't know where is located.If is an way to fix that i will say thanks.Sorry for bad post but my phone didn't do anything it have problems.What i will do , no one of the youtube tutorials helped much.It does not boot loop anything like a blank screen not flash nothing happened. It does not have bootloader / fastboot / recovery / download mode anyone it's very bricked i cannot undo anything.
Thanks for reading this threat
Bump for help
Sorry if i bump so i need help with this device GT-S5300 for 5 years i must take tomorrow to repair service device so i have 2 pictures of my device that cannot boot into recovery and download mode. :crying:
What i will say not booting into recovery and download and boot is dead without os it cannot vibrate the android and show samsung logo
Here is pictures of android and proof not booting a lot
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This device must be fixed with all costs so i am Romanian maybe chance to survive or fix is 10
Tommorow i will take it to repair and i explain the situation maybe i replace the motherboard aswell with gingerbread os 2.3.6 I Hope there is a chance to repair so good luck to me
Fixed GT-S5300 Unbricked motherboard
I have good news my motherboard has been changed and had an low price so the repair was successfully
My samsung have the last chance i guess so must avoid forced upgrades and force format because maybe bricking again so i root an flash zip and worked and partition fine
Now that problem has been resolved i must ask someone to end this topic :good:
Carefull gingerbread i warned myself :fingers-crossed::victory:
When I was at Junior High in 9th grade I broke my Samsung GT-S5300 due to improperly install of incorrect custom rom (lollipop) to my phone that's why the device can't read my sd card even the gallery is empty. I broke it on last 2017. And now 2022 I tried to repair it via odin because our school allow us to borrow a laptop (which is I don't have) then repair my phone there and boom! I got my Samsung GT-S5300 back again to normal. It's now 5 years old. I love that phone because it's so hard to break it. I remember I throw my phone and then it's still alive. Until now it's still alive (but the home key don't work) but I can still use it. My favorite phone is this samsung gt-s5300. I'm planning to buy the same phone like this but I can't find it in the market (because it's phased out or not available). By christmas I will buy Samsung GT-S5360 (even if I have much money I don't like luxurious phones).