Hi everyone.
I have an HTC Radar. Before several days, I took off the battery cover. Of course the phone shutdown. When I put it back and pressed the power on the phone made a buzzing note and gave me nothing but a black screen. I tried several times but the result was the same. I google it a little and found instructions about hard reseting the phone
xxx.htc.com/help/uk/howto_iframe.aspx?id=126596&type=1&p_id=416
The phone boots in this mode and I chose to make a factory reset hoping that this could bring the phone back. Unfortunately this had no result. The phone makes the same exactly. Seems to start but then nothing happens. I am still able to get in the special menu where I can choose factory reset. And because I bought this phone from another country I am not eligible for warranty in Greece.
Any help to bring back my phone would be appreciated. Thank you very much
The way you describe what happens at switch on is exactly how my phone behaves without the Sim cover on at the back (I think what you are calling the battery cover).
I wonder if somehow one of the connectors isn't functioning on the Sim cover at the bottom of the phone? On my phone there are three simple circuit connectors where a tab on the cover pushes a metal connector against a metal bed. There is also a small plastic micro-switch on the right just below the main casing and this is activated by a small piece of clear plastic stuck into a holder - I would imagine this could dislodge easily.
I would try starting the phone without the SIM in to see if that is interfering with the cover sitting on properly and activating all the connections and the switch and ensure the cover is on very precisely.
If that doesn't work try holding the switches as you switch on - may need several people for that.
Good luck!
Thank you for your reply. Unfortunately I have tried this solution and nothing happens. Must be sth else. I don't understand why it even starts in the special mode. thank you anyway and I wish you and everyone a happy new year.
1:- hold both volume buttons & press+hold power button.
2:-then u willl go to special menu.
3:-use down volume key to highlight "factory reset".
4:-use "Power" button to select......!
Enjoy.....!
Related
Hi.
I've go an o2 XDA. I'm finding that when the unit it is my pocket, and I take it out and turn it on, it has soft reset, and displays the o2 logo just as it I had soft reset it - It then boots into windows.
I've got the leather case for it, so when i wear the XDA on my belt, it doesn't soft reset. I think there is a problem with the button or something. Is there a way of disabling that soft reset button via some software (a physical way would prevent me of soft resetting, which is occasionally necessary)???
Help would be greatly appreachiated!
Thanks.
i took the XDA apart the other day, by taking the battery off. Don't do this unless you want to hard reset (i forgot this, and learnt the hard way!!!)
Anyway, got rid of all the dust, and it seemed to have fixed the problem! But, i had to soft-reset again manually, because a program crashed, and now it's back to its usual tricks
Could be a faulty sort reset button? Or could that bit of plastic that covers the switch be pushing into the switch?
Looks like i'll have to take the back off again and check.
Anyone else had this problem? Or is there a way of using software to disable the soft reset button, and use something else to soft reset instead?
Yep, its the rubber protecting the sim card. try turning off your device and squeeze or rub tightly the sim card door then press the power button. it will show the o2 screen meaning that the device just finished a soft reset. mainly its because of the heat that makes the rubber somewhat bigger or something. that suck. :evil:
::adit
Annoying soft resets
Yes, my new Qtek 1010 does the same thing - extremely annoying. My old O2 XDA that I bought a year ago never did this.
I'm not so sure it's the rubber SIM card cover though. I don't seem able to make it reset by fiddling with that. But if I gently drop it end first onto a tabletop (from a very low height!) it will sometimes reset itself.
David
Hi all. Thanks for the replies and advice!
is there a way of "glueing" down the little switch that engages when you open the rubber thing that covers the SIM card? The switch seems a bit unnecessary!
I opened the cover and took the sim card out yesturday, and put the sim card back in, then shut the cover - I thought i'd completely nackered the XDA, because the screen was very faint, the image would fade away, or there would be loads of black lines running across the screen!
I got the phone from Ebay, so no warranty - was nearly crying! So, left it for 10 minutes turned off, and turned it back on and it worked fine! Wierd eh!
Yep I HAD the same problem with my O2 XDA. Only did it when it was in my pocket.
I put a little folden up piece of paper above the switch so that it is pressed down always and closed the rubber lit. And it has never reset once while in my pocket!
Because of the paper it will not reset even when the rubber lit is open.
What a great thread
My xda has been driving me nuts with this problem.
Cheers will jam the switch
Hi all,
I have an O2 XDA II which was flashed last year to WM2003se.
Now I would like to upgrade it to WM6.1, but I cannot enter bootloader mode (using [Power Button] + [D Pad] + [Soft Reset]) because my power button is broken. This means, I also cannot do a hard reset, unless I remove the battery for a long time.
The phone otherwise is working quite well.
Is there any other way to enter bootloader mode?
Thanks in advance!
First, some advice. Several people have asked this question and it has been responded to in other threads. On forums, ALWAYS try and use the search function before asking. It might save you some time, and it also may give you further ideas or solutions to the problem. Now on to the response I gave someone else last year. Read the whole post.
IT IS POSSIBLE!
BUT DO THIS AT YOUR OWN RISK!!! I'M NOT RESPONSIBLE FOR ANY DAMAGED OR FRIED PDAs
I know because I myself have done it on an I-mate (Himalaya). It took some trial and error but I am now running WM6. In my case though, I had to completely remove the power button from the device. The previous owner dropped it on its head, and I got it for free, unfortunately most of the top is missing, including the power button.
SO, on to how I did it. I took a paper clip (metal) and put it about 1cm down, slightly to the right of where the power button used to connect to the motherboard. Make sure you have turned your XDA/IMATE on before doing this. You'll find that when you find the right area, your device will turn off, or the screen will go dark (like holding the power button for a second or giving it a quick tap).
If you manage to hold it there for the right period of time, while pressing the other bootloader buttons, then you will be able to enter bootloader.
This took me close to an hour to get just right, on both occasions I have done it, but it eventually worked.
Note: I have no idea how exactly this worked, but it did. My IMATE was useless without me updating the rom, so I had no worry about frying it if I did something wrong, that is why I was OK with playing around with its insides. BEWARE that you MAY DO DAMAGE to the device.
Good luck.
Hi my power button is broken too.
I'd love to upgrade to WM6 but can't get into bootloader mode...the paper clip approach sounds risky!
Is there an application that can get me to bootloader mode? I've searched but come up with nothing.
Any ideas?
I tried everything before doing the paperclip trick, it was the last straw for me. I did a pretty intensive investigation to other possibilities but couldn't find one.
Maybe you can find something that was a similar shape to your power button? It is a long shot but it may work. If the power button isn;t completely broken off you may still be able to use it.
Thanks Jadel.
Naaa the button has completely come off.. on its side..facing the front of the XDA. Interesting to see that other people have damaged the power button.
I might give it (the paper clip approach) a go and see how it goes.
Thanks,
Taz
tazjamez said:
Thanks Jadel.
Naaa the button has completely come off.. on its side..facing the front of the XDA. Interesting to see that other people have damaged the power button.
I might give it (the paper clip approach) a go and see how it goes.
Thanks,
Taz
Click to expand...
Click to collapse
Same power button problem here... I found this thread and it inspired me to another idea that works very well. I disassembled the unit according to instructions I found here in other threads. I found my button was broken off from the motherboard completely and in addition it was mechanically so damaged that is was unusable for resoldering. I disassembled the (very small) switch under a microscope and it is basically a small round steel disc that works as a spring. It "clicks" when you push the center of the disk. In the center of the switch is a contact point so when the disc is pushed it makes contact and when released it clicks back. (works like the clicking frog we used to play with as a kid). It solders onto the motherboard using 4 solder pads. The two top pads are both connected to the ground plane of the motherboard. The bottom ones are 2 separate contact islands and are not connected to each to each other. (infinite resistance between them). I soldered 3 wires onto the pads, one ground and both lower unknown contact pads. Brouhgt the wires out through the broken button hole in the cover and YES, it works like a charm. If I connect the ground wire to the lower right pad it switches on and off and I can also hard reset the unit. I have not found out what the function is of the other (left lower pad) connected to ground. Maybe it has to do with holding the button longer then a second to switch backlight on and off. In my case I cannot find any functionality. I can now manually short the wires or I can solder a small microswitch to the wires and flash my original QTEK 2020 to WM 6.1. I am going to try that this week end. Anyway no unreliable fumbling with a paper clip.
HI all,
I have made a short how-to video on how to flash one of the many awesome roms (made by our awesome rom-makers) onto a device that doesn't have a power button. I have done it several times and as the question keeps getting raised, I thought I would show some proof.
Some advice before the video.
DO THIS AT YOUR OWN RISK!!! I'M NOT RESPONSIBLE FOR ANY DAMAGED OR FRIED PDAs
I have done this myself on an I-mate (Himalaya). It took some trial and error but I am now running WM6.1. In my case though, I had to completely remove the power button from the device. The previous owner dropped it on its head, and I got it for free, unfortunately most of the top is missing, including the power button.
SO, on to how I did it. I took a paper clip (metal) and put it about 1cm down, slightly to the right of where the power button used to connect to the motherboard (in line with the text section of the Contact button on the top left of your XDA). Make sure you have turned your XDA/IMATE on before doing this. You'll find that when you find the right area, your device will turn off, or the screen will go dark (like holding the power button for a second or giving it a quick tap) or it will flash on and off.
If you manage to hold it there for the right period of time, while pressing the other bootloader buttons, then you will be able to enter bootloader.
This took me close to an hour to get just right, on both occasions I have done it, but it eventually worked and you eventually get quicker (5 minutes for me now).
My IMATE was useless without me updating the rom, so I had no worry about frying it if I did something wrong, that is why I was OK with playing around with its insides. BEWARE that you MAY DO DAMAGE to the device.
Good luck.
Here is the video.
http://www.youtube.com/watch?v=oWfcpC1VM5g
Cheers! Hope this helps some people out there get the most out of their Himalayas again.
JADEL
Wow!
I have seen the video but somhow I felt that whatever you wanted to show is not getting properly visible. Perhaps the illumination is not that much.
But, I ould very well see the c_shekhar's bootsplash screen. hehe
Thanks for the Video. Worked a treat! Now I can flash my XDA again. Yeah the video was a little dark but I got the jist of it anyway.
Glad it has helped someone other than me. Someone also left a comment on the YouTube page that it worked for them as well, which is also good. Our Himalaya's will live on for many years to come!!!
I agree with my video being too dark (Environmentally friendly fluorescent lights are good for environment, bad for how-to videos). I will try and make a new, lighter video next time C_Shekhar ports a new rom!
Power button
I'm from the philippines. I was able to have my XDAII power button repaired it didn't cost that much. If there are repair shops in your area, maybe you can ask about it.
chinister said:
I'm from the philippines. I was able to have my XDAII power button repaired it didn't cost that much. If there are repair shops in your area, maybe you can ask about it.
Click to expand...
Click to collapse
There are only two companies in Australia I know of that can officially fix our XDAs. They are bot hin Rockhampton (about 20 hours from where I live in Sydney).
They are both owned by the same company.
As you can imagine, I would predict that the repair cost would be very high, considering they essentially have a monopoly on the situation, and postage costs, insurance etc
I have a qtek 2020 with the key broken (it misses completely) power. can I perform your procedure?
Thanks
Catalogna
Hi there,
It is hard to say for sure. The only way to know for sure is to actually try it. This procedure has worked repeatedly (at least nine times now for me) on my Himalaya, and several other peoples. It really is a last resort though, so you may want to trry everything else you possibly can first.
Cheers.
good good good
I have put the qtek in bootloader and I now have the new rom. Thanks.
I have solo another problem: after few second what I don't use it the display goes to standby and I must press strong to reactivate it. is it a problem software or hardware?
Glad to hear you were able to flash the new rom.
As for the restarting, I have not seen that before under this ROM, and I have used it on several devices and tested it fairly thoroughly. Are you sure nothing is still stuck in the top of your phone where the power button was (IE you didn't leave the metal device in the top?) Perhaps something in there keeps shorting it out?
Maybe it is just on a short timeout. Check under Start>Settings>System>Power>Advanced
See what time the settings are set to under here for "Turn off device if not used for..." both on battery and external power.
Also, then click on the "backlight" button at the bottom, and check those settings.
Under "Backlight" click on "Battery power" and change the settings to what you want, then click on "External Power" and do the same again.
Then just hit the OK button (top right corner) twice, and you should be done.
Hope this helps.
Thanks!
Hi Jadel. I just want to say thanks! Your video help me deal with a broken power button when upgrading rom for the first time. Without your help, I would never feel like having a brand new phone for free
I also found a way to hard reset a phone without camera button (or record).
Just connect mtty via usb into bootloader, type:
password BOOTLOADER
task 28 0 0
and reset your device as normal.
In my try it corrupted my splash screen but anything other is okay
ROMS
Why on the HD2 do they make roms for SPL 1.4 when every FREAKIN PERSON on the PLANET has version 2.08 I have NO IDEA! STUPID!
Flashing rom
hi im from india and im using an imate ultimate 8502 mobile and unfortunately when i was soft resetting ma phone my phone was corrupt and it mholds in the boot screen itself whenever i restart my phone it stays in the blue sreen stating i mate it doesnt moves from it and boot loader cant be opened ive tried both the ways like holding power button & volume - key as well as holding fn and red button and reset key even both doesnt respond ive given my ,mobile to service to all of the servise centers in chennai but none of them cant service it can anyone help me out plzzzzzzzzzzzz...........
THANKS!
The power button has been a little fussy...requiring a hard press to power up but it had been until today. Button does not give a tactile "click" when pressed. Out of warranty. Opened it up...the microswitch isn't "clicking" Used a needle to jump the switch and it is now powered up but would like to know
1. is it fixable? (I don't solder and haven't a clue on where to get the microswitch)
2. Does the main board have to be replaced to fix it? Where can it be ordered?
3. Does anyone know of a reliable place that can either fix the switch or replace the board? I'm not going to deal w/ At&t; this was a replacement for the white screen of death and until today; it's been perfect. Everything else is working, perfect screen, case, keyboard. Battery stays charged for 12+ hours even w/ bluetooth running for over 18 months.
You cold look on ebay for a "broken" Hermes. I got a couple and found there wasn't anything wrong with them.
I don't know where you might be able to get a microswitch from but it will require soldering to fix. Unfortunately the Hermes motherboard is multilayered and this may mean fixing yourself may not work. Taking it to someone WILL cost $$$ so be sure to try and pin them with a quote for parts and labour before they "attempt" to fix it.
Good luck...
Power button screwed ..any HELP!!
Hi Friends,
I screwed my HTC Hermes power button while trying to fix its earlier problem.
Now to turn the backlight on ..i changed the settings and I can now use any button to bring it out of Sleep mode....
I used a program available on this site to enter bootloader.
However, the problem remains when "power button" is to be pressed.
Any advice on how to get over the "Press power button" to start the ROM flashing....
I found the part on celluardr.com for 32.00 which I think is a little expensive! They may be able to change it but that will cost $$. A possible solution is to clean the switch with an electronic cleaner solution that evaporates very quickly. I suggest you remove the battery with the case open to expose the switch - really mean remove the back casing to expose the motherboard and with the tube attached to the spray can squirt in the solution. Press the switch in before the solution dries - you may have some crap that got in there and is sticking up the switch mechanism. Dirt will do this.
QUESTION: What program/changes did you make to change the phone's ability to recover from sleep mode? I'd like to preserve the power button on mine and use another key that can be replaced without changing the motherboard - Ie the front phone buttons.
stim141 said:
I found the part on celluardr.com for 32.00 which I think is a little expensive! They may be able to change it but that will cost $$. A possible solution is to clean the switch with an electronic cleaner solution that evaporates very quickly. I suggest you remove the battery with the case open to expose the switch - really mean remove the back casing to expose the motherboard and with the tube attached to the spray can squirt in the solution. Press the switch in before the solution dries - you may have some crap that got in there and is sticking up the switch mechanism. Dirt will do this.
QUESTION: What program/changes did you make to change the phone's ability to recover from sleep mode? I'd like to preserve the power button on mine and use another key that can be replaced without changing the motherboard - Ie the front phone buttons.
Click to expand...
Click to collapse
Hi stim141,
Thanks for your suggestions.. i shall give it a try and let you know the progress (if any)
ANSWER: From Start-> Settings-> System-> Key lock
Change the settings here to see that NO buttons are locked when in STANDBY/ SLEEP mode - when backlight turns off.
This will help to bring the device out of standby/ sleep mode.
You can have the device lock enabled so that when in sleep mode no functions are activated if any button is pressed accidentally. when any key is pressed ...it just shows you the UNLOCK option.
Also, I read somewhere, sliding out the keyboard slightly also wakes the device.
i just recieved my evo 3d today threw ups. and i noticed my power button is hard to press to turn the screen off... anyone else ran into this problem?
The button is built into the battery cover so remove it and place it back on.
Sent from my PG86100 using Tapatalk
make sure your battery door is completely on and snapped in the correct spots.
i have issues where either the power button is way too easy to press or way too hard. hopefully a new case will solve that.
I had a badly dysfunctional power switch with my first 3VO, I have since exchanged it for a new one.
And, no, in my case it was not the battery cover-power switch interface, it was the switch itself. I removed the cover and directly pressed it. Strange thing was, with mine, if I removed and replaced the battery, I could get one or two presses that registered, otherwise nothing -- no wake/sleep, no power off/on.
My wife and I both have Evo 3d's and her power button is way easier to push than mine. I switched the back covers between the phones and the problem followed the cover. I looked at both and the power button on my cover isn't molded correctly where it pushes on the phone. It is shorter so it sits further in the phone and doesn't work quite right. I called HTC and Sprint and there isn't a replacement cover available yet so they are going to switch out the phone.
I had a power button issue, where if I pushed the button, it would come up with the shutdown menu and no option just turn off the screen. Was in the process of going take it back for a replacement and found that when I removed the case to switch the memory card that my one was working as it should. The hardness went away and the option to turn off the screen came back. Strangest thing I seen since it truly seemed like a hardware issue.
i am going to check a few out in store and see if mine is like what you describe. To me its set pretty low and the button doesnt stick out very far.
Mine sticks out pretty far... isn't easy, or hard to press. I guess i got lucky.
Mine is really touchy, when I press it to lock the phone it sometimes goes to the shutdown popup. Sorry this post wasn't more helpful to the op, lol, just sharing.