hey everyone, yes im abit of a noob and need some help.
i was trying to install Arch on my touchpad and hit an error. now my touchpad keeps cycling the hp logo and wont turn on or off. ive tried webos doctor and still this problem is still here.
please help
thank you for any help given
give us some details on how did it occur and what were you doing when it gave you an error (what was the last command you run for example)
"curl -O http://archlinuxarm.org/mirror/touchpad/ArchLinuxARM-touchpad-latest.tar.gz"
this was the last command i wrote, and it downloaded about 39mb and failed. before this i had partitioned the hard drive too.
is this fixable?
sissons87 said:
before this i had partitioned the hard drive too.
Click to expand...
Click to collapse
i think the keyword for the problem is here, can you recall what commands exactly did you run?
also just like chessmaster w/nook asked you, do you have moboot installed?
Holding down the power and home key always reset my tp. And with HP its pretty impossible to brick ur device HP doc
okay heres a detailed explanation of what i done.
i put my touchpad in to dev mode.
accessed novaterm from my ubuntu window.
i then followed all of these commands:
"mount -o rw,remount /boot
cd /tmp
curl -O http://moboot.googlecode.com/files/moboot_0.3.5.zip
unzip moboot_0.3.5.zip
mv uImage.moboot_0.3.5 /boot/uImage.moboot
cd /boot
rm uImage
ln -s uImage.moboot uImage
ln -s uImage-2.6.35-palm-tenderloin uImage.webOS
echo "yes" > moboot.verbose.ArchLinuxARM
sync
curl -O http://archlinuxarm.org/mirror/touchpad/uImage.ArchLinuxARM
curl -O http://archlinuxarm.org/mirror/touchpad/moboot.splash.ArchLinuxARM.tga
cd /tmp
pkill -SIGUSR1 cryptofs
umount /media/internal
echo "STOP HERE AND READ 'RESIZE FAT' BEFORE CONTINUING" # See below
resizefat /dev/store/media ****M
lvm.static lvresize -L -4096M /dev/store/media
lvm.static lvcreate -L 4096M -n arch-root store
mkfs.ext3 /dev/store/arch-root
mkdir linux
mount /dev/store/arch-root linux
cd linux
curl -O http://archlinuxarm.org/mirror/touchpad/ArchLinuxARM-touchpad-latest.tar.gz
tar xzf ArchLinuxARM-touchpad-latest.tar.gz # Will take a long time
rm ArchLinuxARM-touchpad-latest.tar.gz
cd ..
umount linux
reboot # The first few times, this may error out - try again"
where the ****M is i put 7944M i think this may be the issue.
when i got to this command it started downloading and then got an error at 39mb:
"curl -O http://archlinuxarm.org/mirror/touchpad/ArchLinuxARM-touchpad-latest.tar.gz"
ive then ran webos doctor numbers of times but no luck. it wont even let me novaterm back in not sure what to do :/ any help would be great.
sissons87 said:
hey everyone, yes im abit of a noob and need some help.
i was trying to install Arch on my touchpad and hit an error. now my touchpad keeps cycling the hp logo and wont turn on or off. ive tried webos doctor and still this problem is still here.
please help
thank you for any help given
Click to expand...
Click to collapse
I had that same bootloop problem. Try this: http://forum.xda-developers.com/showthread.php?t=1426244
rr5678 said:
I had that same bootloop problem. Try this: http://forum.xda-developers.com/showthread.php?t=1426244
Click to expand...
Click to collapse
All has worked okay but having problems creating swap store. Error im getting is:
Redundant stripes arguement: default is 1
Insufficiant free extents (0) in volume group store: 64 required
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
sissons87 said:
All has worked okay but having problems creating swap store. Error im getting is:
Redundant stripes arguement: default is 1
Insufficiant free extents (0) in volume group store: 64 required
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
Click to expand...
Click to collapse
Did you enter
"lvm.static lvcreate -l 1761 -i 1 -M y --major 254 --minor 6 -n media store"
or
"lvm.static lvcreate -l 3523 -i 1 -M y --major 254 --minor 6 -n media store"?
rr5678 said:
Did you enter
"lvm.static lvcreate -l 1761 -i 1 -M y --major 254 --minor 6 -n media store"
or
"lvm.static lvcreate -l 3523 -i 1 -M y --major 254 --minor 6 -n media store"?
Click to expand...
Click to collapse
I entered " "lvm.static lvcreate -l 1648 -i 1 -M y --major 254 --minor 6 -n media store" i wouldnt let me put 1761 cus i got the same sort of error.
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
sissons87 said:
I entered " "lvm.static lvcreate -l 1648 -i 1 -M y --major 254 --minor 6 -n media store" i wouldnt let me put 1761 cus i got the same sort of error.
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
Click to expand...
Click to collapse
Okay, try it again, except this time, enter
"lvm.static lvcreate -l 1584 -i 1 -M y --major 254 --minor 6 -n media store"
Okay how do i undo what ive just done? Run all commands again?
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
sissons87 said:
Okay how do i undo what ive just done? Run all commands again?
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
Click to expand...
Click to collapse
Yes, running them again will erase all the necessary stuff so you can rebuild it.
Okay thank you, i will try that now
Sent from my HTC Sensation XE with Beats Audio Z715e using xda premium
Hii !
I got exactly the same problem ! And I followed a tutorial I found on rootzwiki (dumb I can't post the link cuz this is my first message).
Anyway look for that on Google (with the quotes) :"HOW TO make a larger cm7 data partition" touchpad
It's a txt file and it worked all fine on mine. Hope it would help you.
would like to thank you all for all your help rr5678 you were a great help! im going to and try install arch again or another os now. wish me luck dnt learn with out try eh
Thanks a lot rr5678 too for your tutorial, I figured that the tutorial I found wasn't good as yours.
sissons87 said:
would like to thank you all for all your help rr5678 you were a great help! im going to and try install arch again or another os now. wish me luck dnt learn with out try eh
Click to expand...
Click to collapse
Glad to hear that it worked for you.
Related
hi there..is there a thread for new tutorial for installing openvpn for the gingerbread?
i already tried the search button but theres such no topic except for jimbo..which is kinda outdated..im a bit skeptic asking him because he no longer possess an x10.?
i tried to issue this command on TE
su
mkdir /system/xbin/bb
ln -s /system/bin/busybox /system/xbin/bb/ifconfig
ln -s /system/bin/busybox /system/xbin/bb/route
Click to expand...
Click to collapse
but the openvpn settings wont let me select any of my OVPN files..?
thanks.
forget it..
already figured it out..
i dont have many apps on my phone and need the space on sdcard for photos and videos....
so i made an init.d script to move some big folders (games) from sdcard to /data/ and /system/ partition because there is much space left.
Code:
busybox mkdir -p /sdcard/Android/obb/com.nextgenreality.minimoto
busybox mkdir -p /data/Android/obb/com.nextgenreality.minimoto
mount -o bind /data/Android/obb/com.nextgenreality.minimoto /sdcard/Android/obb/com.nextgenreality.minimoto
busybox mkdir -p /sdcard/Navigon
busybox mkdir -p /data/Navigon
mount -o bind /data/Navigon /sdcard/Navigon
rm -r /sdcard/Android/data/com.eamobile.sims3_row_qwf
busybox mkdir -p /sdcard/Android/data/com.eamobile.sims3_row_qwf
busybox mkdir -p /data/Android/data/com.eamobile.sims3_row_qwf
mount -o bind /data/Android/data/com.eamobile.sims3_row_qwf /sdcard/Android/data/com.eamobile.sims3_row_qwf
rm -r /sdcard/Android/data/com.eamobile.nfshp_row_wf
busybox mkdir -p /sdcard/Android/data/com.eamobile.nfshp_row_wf
busybox mkdir -p /system/Android/data/com.eamobile.nfshp_row_wf
mount -o bind /system/Android/data/com.eamobile.nfshp_row_wf /sdcard/Android/data/com.eamobile.nfshp_row_wf
after a reboot i have moved around 1gb to data and 320mb to system ->
Code:
Filesystem Size Used Free Blksize
/dev 386.3M 64.0K 386.3M 4096
/mnt/asec 386.3M 0.0K 386.3M 4096
/mnt/obb 386.3M 0.0K 386.3M 4096
/dev/shm 386.3M 0.0K 386.3M 4096
/system 1007.9M 891.6M 116.3M 4096
/modemfs 2.8M 1.1M 1.7M 1024
/data 2.0G 1.7G 269.0M 4096
/cache 246.1M 4.2M 241.8M 4096
/mnt/sdcard 11.3G 5.1G 6.1G 32768
/mnt/secure/asec 11.3G 5.1G 6.1G 32768
/mnt/sdcard/Android/obb/com.nextgenreality.minimoto 2.0G 1.7G 269.0M 4096
/mnt/sdcard/Navigon 2.0G 1.7G 269.0M 4096
/mnt/sdcard/Android/data/com.eamobile.sims3_row_qwf 2.0G 1.7G 269.0M 4096
/mnt/sdcard/Android/data/com.eamobile.nfshp_row_wf 1007.9M 891.6M 116.3M 4096
be aware that these data are lost if you reflash your rom !!!
have fun
inteks
[edit]
to let you know. i faced a small problem and found a solution
after i moved some big folders to phone memory i got a "low phone memory" at 200mb ?! witch i find is MORE than enogh !
this warning come usally at 10% ....
i found a mod to change the threshold to i.e. 2 or 5% :good:
http://forum.xda-developers.com/showthread.php?t=877793
so i can use this script ( or make my own, which would be very similar) on the xperia u too rite?
unreal3000 said:
so i can use this script ( or make my own, which would be very similar) on the xperia u too rite?
Click to expand...
Click to collapse
Yep, you should be able to.
@OP: what you need is to write a generic script that moves directories based on a plain text list on /sdcard.
there is a sd card in xperia P ? oO
ilgreco112 said:
there is a sd card in xperia P ? oO
Click to expand...
Click to collapse
There is no sdcard, but /sdcard is a separate partition.
the main idea stays the same. the xperia u has a partition which acts as an internal sd. so lets say i want to move my music folder on the sdcard to the /data partition. will this work? -
Code:
busybox mkdir -p /sdcard/music
busybox mkdir -p /data/music
mount -o bind /data/music /sdcard/music
tks fr the help!
unreal3000 said:
the main idea stays the same. the xperia u has a partition which acts as an internal sd. so lets say i want to move my music folder on the sdcard to the /data partition. will this work? -
Code:
busybox mkdir -p /sdcard/music
busybox mkdir -p /data/music
mount -o bind /data/music /sdcard/music
tks fr the help!
Click to expand...
Click to collapse
should work, but you should use it for i. e. gamedata that you can always redownload. because if you reflash your phone this data will be lost.
btw. next version of setxperia is able to execute /sdcard/userinit.sh then you can easily edit this file on pc when phone is docked...
Gesendet von meinem LT22i
inteks said:
should work, but you should use it for i. e. gamedata that you can always redownload. because if you reflash your phone this data will be lost.
btw. next version of setxperia is able to execute /sdcard/userinit.sh then you can easily edit this file on pc when phone is docked...
Gesendet von meinem LT22i
Click to expand...
Click to collapse
so your saying once i have my music folder on the /data partition, i cant edit it through the sdcard partition? (like copy things to the music folder on the sd from my comp, but it would actual get stored on the /data partition?)
unreal3000 said:
so your saying once i have my music folder on the /data partition, i cant edit it through the sdcard partition? (like copy things to the music folder on the sd from my comp, but it would actual get stored on the /data partition?)
Click to expand...
Click to collapse
Yeah, that's exactly it.
unreal3000 said:
so your saying once i have my music folder on the /data partition, i cant edit it through the sdcard partition? (like copy things to the music folder on the sd from my comp, but it would actual get stored on the /data partition?)
Click to expand...
Click to collapse
no you can't access them through PC. on PC these folders are empty. as i said this is only useful for i. e. big game folder to save some space...
Gesendet von meinem LT22i
to let you know. i faced a small problem and found a solution
after i moved some big folders to phone memory i got a "low phone memory" at 200mb ?! witch i find is MORE than enogh !
this warning come usally at 10% ....
i found a mod to change the threshold to i.e. 2 or 5% :good:
http://forum.xda-developers.com/showthread.php?t=877793
ok.... last version of setxperia can execute "/sdcard/userinit.sh"
btw. i change the script to use a function to mount folders. its easier to add new locations here is the act version of my /sdcard/userinit.sh -->>
Code:
echo '/dev/block/mmcblk0p14' > /sys/devices/platform/usb_mass_storage/lun0/file
echo '1' > /sys/devices/virtual/usb_composite/usb_mass_storage/enable
checkMount(){
if grep -qs $1 /proc/mounts; then
echo "$1 is allready mounted"
else
busybox rm -r $1
busybox mkdir -p $1
busybox mkdir -p $2
mount -o bind $2 $1
echo "$1 successfully mounted"
fi
}
checkMount '/sdcard/Navigon' '/data/Navigon'
checkMount '/sdcard/Android/data/com.eamobile.sims3_row_qwf' '/data/Android/data/com.eamobile.sims3_row_qwf'
checkMount '/sdcard/Android/data/com.eamobile.nfshp_row_wf' '/system/Android/data/com.eamobile.nfshp_row_wf'
checkMount '/sdcard/Android/data/com.opera.browser' '/cache/Android/data/com.opera.browser'
checkMount '/sdcard/PlayerPro' '/cache/data/PlayerPro'
Hi inteks i own a xperia U. I want to move asphalt 7 gamedata to the data partition. I used this script:
rm -r /sdcard/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
busybox mkdir -p /sdcard/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
busybox mkdir -p /system/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
mount -o bind /data/Android/obb/com.gameloft.android.ANMP.GloftA7HM /sdcard/Android/obb/com
But its still in the sdcard partition after reboot. Something wrong i'm doing here. Please point it out so i can move the data.
Thanks !
Sent from my ST25i using Tapatalk 2
Rapier07 said:
Hi inteks i own a xperia U. I want to move asphalt 7 gamedata to the data partition. I used this script:
rm -r /sdcard/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
busybox mkdir -p /sdcard/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
busybox mkdir -p /system/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
mount -o bind /data/Android/obb/com.gameloft.android.ANMP.GloftA7HM /sdcard/Android/obb/com
But its still in the sdcard partition after reboot. Something wrong i'm doing here. Please point it out so i can move the data.
Thanks !
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
busybox mkdir -p /system/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
mount -o bind /data/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf /sdcard/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
a few errors in script...
inteks said:
busybox mkdir -p /system/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
mount -o bind /data/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf /sdcard/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf
a few errors in script...
Click to expand...
Click to collapse
Oh.. What should i use in place of them?
Edit: i get it i guess. Will try again and report back.
Thanks for your help.
Sent from my ST25i using Tapatalk 2
No go
I've been trying this since morning. Tried one more method and it destroyed my gta3 data.
Could you please write the full script i need to use?
The gamedata location is
/sdcard/Android/obb/ com.gameloft.android.ANMP.GloftA7HM
Thanks.
Sent from my ST25i using Tapatalk 2
Rapier07 said:
No go
I've been trying this since morning. Tried one more method and it destroyed my gta3 data.
Could you please write the full script i need to use?
The gamedata location is
/sdcard/Android/obb/ com.gameloft.android.ANMP.GloftA7HM
Thanks.
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
how do you start the script ? /etc/init.d or /sdcard/userinit.sh with setxperia ?
have you tryed my new script ?
save this to /sdcard/userinit.sh and use setxperia .... -->>
checkMount(){
if grep -qs $1 /proc/mounts; then
echo "$1 is allready mounted"
else
busybox rm -r $1
busybox mkdir -p $1
busybox mkdir -p $2
mount -o bind $2 $1
echo "$1 successfully mounted"
fi
}
checkMount '/sdcard/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf' '/data/Android/obb/com.gameloft.android.ANMP.GloftA7HM_row_wf'
Click to expand...
Click to collapse
but keep in mind after this you have to redownload gamedata ...
parameter of checkmount -> "checkmount orginalfolderpath newfolderpath"
Hi... I m kinda noob... So could u plz tell me to steps to follow to how to get this done.... Tnx
Sent from my ST25i using xda app-developers app
Hi guys,
I started having this issue that every-time I use the Touchpad on CM9 or WebOS it just freezes and reboots/resets...
Take a look:
No mater what I do (I've tried this souldevteam.net/blog/2012/07/24/fix-bricked-hp-touchpad-recovering-software-bricked-touchpad it always goes back to reboot/reset loop as soon as I start to use it.
I have this Touchpad since new and never had any issues in the pass.
I would like some pointers in what can I do to repair, is the problem at the mainboard? memory? hdd? I could use this place to get parts: portatronics.com
Thanks!
It does it both in CM9 and WebOS? If so, I'd just run the ACMEUninstaller, run WebOS Doctor and once thats all finished, boot into WebOS (DONT install Android yet) and see if it continues bootlooping.
This thread may be of use to you. http://forum.xda-developers.com/showthread.php?t=1564938
allstar319 said:
It does it both in CM9 and WebOS? If so, I'd just run the ACMEUninstaller, run WebOS Doctor and once thats all finished, boot into WebOS (DONT install Android yet) and see if it continues bootlooping.
This thread may be of use to you. http://forum.xda-developers.com/showthread.php?t=1564938
Click to expand...
Click to collapse
Yes on both, same thing:
I did use ACMEUninstaller and then wiped the partitions:
Code:
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static vgremove store
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static vgcreate -s 8M store /dev/mmcblk0p14
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static lvcreate -l 71 -i 1 -M y --major 254 --minor 0 -n root store
lvm.static lvcreate -l 8 -i 1 -M y --major 254 --minor 1 -n var store
lvm.static lvcreate -l 2 -i 1 -M y --major 254 --minor 2 -n update store
lvm.static lvcreate -l 3 -i 1 -M y --major 254 --minor 3 -n log store
lvm.static lvcreate -l 32 -i 1 -M y --major 254 --minor 4 -n mojodb store
lvm.static lvcreate -l 17 -i 1 -M y --major 254 --minor 5 -n filecache store
lvm.static lvcreate -l 3523 -i 1 -M y --major 254 --minor 6 -n media store
lvm.static lvcreate -l 64 -i 1 -M y --major 254 --minor 7 -n swap store
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
mkdosfs -f 1 -s 64 /dev/store/media
Then I do a WebOS 3.0 then 3.05, same thing.
I guess it is highly probable to be a Hardware problem, do you know who can fix this besides HP?
Thanks!
Jor3lBR said:
Yes on both, same thing:
I did use ACMEUninstaller and then wiped the partitions:
Code:
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static vgremove store
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static vgcreate -s 8M store /dev/mmcblk0p14
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static lvcreate -l 71 -i 1 -M y --major 254 --minor 0 -n root store
lvm.static lvcreate -l 8 -i 1 -M y --major 254 --minor 1 -n var store
lvm.static lvcreate -l 2 -i 1 -M y --major 254 --minor 2 -n update store
lvm.static lvcreate -l 3 -i 1 -M y --major 254 --minor 3 -n log store
lvm.static lvcreate -l 32 -i 1 -M y --major 254 --minor 4 -n mojodb store
lvm.static lvcreate -l 17 -i 1 -M y --major 254 --minor 5 -n filecache store
lvm.static lvcreate -l 3523 -i 1 -M y --major 254 --minor 6 -n media store
lvm.static lvcreate -l 64 -i 1 -M y --major 254 --minor 7 -n swap store
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
mkdosfs -f 1 -s 64 /dev/store/media
Then I do a WebOS 3.0 then 3.05, same thing.
I guess it is highly probable to be a Hardware problem, do you know who can fix this besides HP?
Thanks!
Click to expand...
Click to collapse
Sorry, nope. Unless someone else can think of a way to fix it, seems it could be a hardware issue. If you're still in warranty, just open up a request with HP and ship it to them. Just be sure to wipe Android completely. If not, search around town and see if any of those phone repair shops can take a look at it or see if HP can fix it for a price.
allstar319 said:
Sorry, nope. Unless someone else can think of a way to fix it, seems it could be a hardware issue. If you're still in warranty, just open up a request with HP and ship it to them. Just be sure to wipe Android completely. If not, search around town and see if any of those phone repair shops can take a look at it or see if HP can fix it for a price.
Click to expand...
Click to collapse
Well I bought it in 12/2011 as a Refurb, so it's out of the warranty.
I could try here but nobody seams to ever heard of this store: www portatronics com
when did it start doing this? before or after you flashed CM9? If it didnt always do this, then it's likely not a hardware issue. if not then try to think of what changes you made that may have done this.
SOLVED
haxin said:
when did it start doing this? before or after you flashed CM9? If it didnt always do this, then it's likely not a hardware issue. if not then try to think of what changes you made that may have done this.
Click to expand...
Click to collapse
Hi I was able to fix it finally!
Because I paid $115 refurb for this brand new I didn't want to send anywhere to pay over $200 for repairs...
So I followed this guide:
HP TouchPad Take Apart Repair Guide Be careful not to brake the clips!
After opening the TP I removed the mainboard only.
I placed the mainboard only inside a non-stick foil paper and placed it in the oven at 395o.F for 10 minutes (like I used to do to my broken video cards in the old days)...
After that I let it rest and the following morning I put everything back together!
Amazingly the TP powered up right away and now is free of the reboot loop issues!!!!!! :evil:
I couldn't believe it but it did work.
My conclusion is that is was a hardware error, most likely weak solder joints in the MB.
That's awesome.
Greetings!
I have tried some ROMs -Ace I SCAPE, REINCARNATION, simplicity v5- and kernels -bieltv 3.0 for cm7, rafael 201211201515- but no matter what, after a few reboots my launcher -that is in the internal memory- and link2SD -that is in the internal memory too- just disappear, I don't know how could I track this since is not consistent -is like after 8-11 reboots-.
I don't have a clue of how to prevent this or what could be triggering it.
PS: Everytime I tried any of the above ROMs with their Kernels, I got back to the stock in ODIN 3.07 then did a fresh clean installation.
Logcat says it all
Try re-creating the case scenario, then using a PC, connect your phone (make sure to enable USB Debugging after the flash) and open a command line (Start->Run->cmd.exe if on windows)
Once open, try the instructions on this thread and upload the logcat here, try to make it as short as possible, I suggest you prepare it all before taking the logcat and once you find the issue, immediately do logcat
Good luck!
El_Dark said:
Logcat says it all
Try re-creating the case scenario, then using a PC, connect your phone (make sure to enable USB Debugging after the flash) and open a command line (Start->Run->cmd.exe if on windows)
Once open, try the instructions on this thread and upload the logcat here, try to make it as short as possible, I suggest you prepare it all before taking the logcat and once you find the issue, immediately do logcat
Good luck!
Click to expand...
Click to collapse
Right after the bug right? Because I wasn't sure if the logcat would explain why is after some reboots and not in the first one.
I'll be updating this post as it happens -usually is "conviently" when I finish installing all of my previous apps, then after 8-10 boots happens-.
sgdva said:
Right after the bug right? Because I wasn't sure if the logcat would explain why is after some reboots and not in the first one.
I'll be updating this post as it happens -usually is "conviently" when I finish installing all of my previous apps, then after 8-10 boots happens-.
Click to expand...
Click to collapse
it's a possible way, but note that it's useless after a reboot lol so it has to be right before you install your apps
El_Dark said:
it's a possible way, but note that it's useless after a reboot lol so it has to be right before you install your apps
Click to expand...
Click to collapse
I installed some apps to see if because I'm installing too many of them are making the phone to cause this -not quite sure if link2SD is working properly-. I had 140 apps before the upgrade -before switching between/roms kernels-, the reason why I upgrade was that I couldn't upgrade from the store the installed apps -it always told me I was running out of memory-.
Anyways, I have tried these days to recrate the scenario , one of the random reboots -when suddenly a message telling Link2SD was not responding- my launcher got out again, when I tried to logcat this by rebooting it worked again
But my whatsapp was gone
Here's the logcat available at paste bin of what I think are the problems:
http://pastebin.com/3jMNX7LV
If needed, I upload the whole thing in box:
https://app.box.com/s/i66rfop429c0wgwldqv4
Anyways I attach the logcat in pastebin
PS: I have read that VFY is missing / replacing in the logcat, for what I have read here
Could be superuser got messed up while flashing the cm7 kernel?
sgdva said:
I installed some apps to see if because I'm installing too many of them are making the phone to cause this -not quite sure if link2SD is working properly-. I had 140 apps before the upgrade -before switching between/roms kernels-, the reason why I upgrade was that I couldn't upgrade from the store the installed apps -it always told me I was running out of memory-.
Anyways, I have tried these days to recrate the scenario , one of the random reboots -when suddenly a message telling Link2SD was not responding- my launcher got out again, when I tried to logcat this by rebooting it worked again
But my whatsapp was gone
Here's the logcat available at paste bin of what I think are the problems:
http://pastebin.com/3jMNX7LV
If needed, I upload the whole thing in box:
https://app.box.com/s/i66rfop429c0wgwldqv4
Anyways I attach the logcat in pastebin
PS: I have read that VFY is missing / replacing in the logcat, for what I have read here
Could be superuser got messed up while flashing the cm7 kernel?
Click to expand...
Click to collapse
Try reflashing... Although the issues I've experienced with Link2SD are usually related to /data/ partition getting full when having too many apps..
If after reflashing, installing Link2SD and linking your apps again you still have issues, download Link2SD again from the Play store, you could also try the following after installing Link2SD and linking your apps: connect your phone to a PC and use adb shell, while the phone boots, once shell is up, do:
Code:
su
cd /data/
ls (make sure here that you have an sdext2 directory, if not, it means Link2SD is not installed properly)
cd sdext2
ls (make sure that you have a dalvik-cache directory in this place, if not, start Link2SD for a
cd /data/dalvik-cache/
for file in data*
do
if [! -h $file] (we make sure it's not a symlink already, you don't want looping links!!!)
cp $file /data/sdext2/dalvik-cache/
rm $file
ln -s /data/sdext2/dalvik-cache/$file $file
fi
done
try that without the text in the parenthesis lol
hope that helps, it could help anyone with space issues in /data/!!
El_Dark said:
All the post above
Click to expand...
Click to collapse
Thanks for being up with this issue!
Well this install is fresh new -is like 2 days long-, I tried the commands you told me but this is what I get
Code:
C:\android-sdk-windows\platform-tools>adb shell
# su
su
# ls
ls
efs
config
cache
sd-ext
sdcard
acct
mnt
vendor
devices
d
etc
fota.rc
init
init.charge.rc
ueventd.rc
data
init.rc
ueventd.goldfish.rc
sbin
lib
init.bcm21553.rc
sys
init.goldfish.rc
proc
recovery.rc
tmp
default.prop
system
res
root
dev
# cd sdext2
cd sdext2
cd: can't cd to sdext2
#
Also I'm not quite sure I understood this line?
El_Dark said:
installing Link2SD and linking your apps again you still have issues, download Link2SD again from the Play store,
Click to expand...
Click to collapse
Do I uninstall and re Install?
sgdva said:
Thanks for being up with this issue!
Well this install is fresh new -is like 2 days long-, I tried the commands you told me but this is what I get
Code:
C:\android-sdk-windows\platform-tools>adb shell
# su
su
[COLOR="Red"]you missed the "cd /data/" part lol[/COLOR]
# ls
ls
efs
config
<<intentionally snipped>>
Also I'm not quite sure I understood this line? Do I uninstall and re Install?
Click to expand...
Click to collapse
Yep, from the Play itself, just in case you're using some local/downloaded version lol, although I doubt it
El_Dark said:
Yep, from the Play itself, just in case you're using some local/downloaded version lol, although I doubt it
Click to expand...
Click to collapse
Ok Thanks for remarking my bad, lol.
Ok I got the dalvik cache folder as you state, though I get an error when typing this line
> ln -s /data/sdext2/dalvik-cache/$file $file
ln -s /data/sdext2/dalvik-cache/$file $file
> fi
fi
Syntax error: "fi" unexpected (expecting "then")
I thought maybe it was an if, but yeah, isn't a "then" missing for the "if [! -h $file]" that we typed before?
Full code:
Code:
C:\android-sdk-windows\platform-tools>adb shell
# su
su
# cd /data/
cd /data/
# ls
ls
log
dontpanic
cache
misc
local
data
app-private
app
property
fota
anr
dalvik-cache
lost+found
brcm
vt
gps
lcs.socket
rilgps.socket
link2sd-debuggerd.log
link2sd-11link2sd.log
zipalign.db
zipalign.log
aeqcoe.txt
soundbooster.txt
system
secure
backup
cp_data.txt
sdext2
tombstones
# cd sdext2
cd sdext2
# ls
ls
lost+found
data
dalvik-cache
com.whatsapp-1.apk
com.jb.gosms-1.apk
com.opera.mini.android-1.apk
com.imo.android.imoim-1.apk
com.urbandroid.sleep-1.apk
com.urbandroid.sleep.full.key-1.apk
je.fit-1.apk
com.jb.gosms.widget-1.apk
jp.co.johospace.jorte-1.apk
com.c2call.app.android.friendcaller-1.apk
com.skype.raider-1.apk
com.viber.voip-1.apk
com.sds.android.ttpod-1.apk
com.facebook.katana-1.apk
com.google.android.apps.plus-1.apk
com.megacloud.android-1.apk
com.google.android.apps.maps-1.apk
com.plaincode.clinometer-1.apk
org.exobel.routerkeygen-1.apk
es.pulimento.wifi-1.apk
# cd /data/dalvik-cache/
cd /data/dalvik-cache/
# for file in data*
for file in data*
> do
do
> if [! -h $file]
if [! -h $file]
> cp $file /data/sdext2/dalvik-cache/
cp $file /data/sdext2/dalvik-cache/
> rm $file
rm $file
> ln -s /data/sdext2/dalvik-cache/$file $file
ln -s /data/sdext2/dalvik-cache/$file $file
> fi
fi
Syntax error: "fi" unexpected (expecting "then")
sgdva said:
Ok Thanks for remarking my bad, lol.
Ok I got the dalvik cache folder as you state, though I get an error when typing this line
> ln -s /data/sdext2/dalvik-cache/$file $file
ln -s /data/sdext2/dalvik-cache/$file $file
> fi
fi
Syntax error: "fi" unexpected (expecting "then")
I thought maybe it was an if, but yeah, isn't a "then" missing for the "if [! -h $file]" that we typed before?
Full code:
Code:
C:\android-sdk-windows\platform-tools>adb shell
# su
su
# cd /data/
cd /data/
# ls
ls
log
dontpanic
cache
misc
local
data
app-private
app
property
fota
anr
dalvik-cache
lost+found
brcm
vt
gps
lcs.socket
rilgps.socket
link2sd-debuggerd.log
link2sd-11link2sd.log
zipalign.db
zipalign.log
aeqcoe.txt
soundbooster.txt
system
secure
backup
cp_data.txt
sdext2
tombstones
# cd sdext2
cd sdext2
# ls
ls
lost+found
data
dalvik-cache
com.whatsapp-1.apk
com.jb.gosms-1.apk
com.opera.mini.android-1.apk
com.imo.android.imoim-1.apk
com.urbandroid.sleep-1.apk
com.urbandroid.sleep.full.key-1.apk
je.fit-1.apk
com.jb.gosms.widget-1.apk
jp.co.johospace.jorte-1.apk
com.c2call.app.android.friendcaller-1.apk
com.skype.raider-1.apk
com.viber.voip-1.apk
com.sds.android.ttpod-1.apk
com.facebook.katana-1.apk
com.google.android.apps.plus-1.apk
com.megacloud.android-1.apk
com.google.android.apps.maps-1.apk
com.plaincode.clinometer-1.apk
org.exobel.routerkeygen-1.apk
es.pulimento.wifi-1.apk
# cd /data/dalvik-cache/
cd /data/dalvik-cache/
# for file in data*
for file in data*
> do
do
> if [! -h $file]
if [! -h $file]
> cp $file /data/sdext2/dalvik-cache/
cp $file /data/sdext2/dalvik-cache/
> rm $file
rm $file
> ln -s /data/sdext2/dalvik-cache/$file $file
ln -s /data/sdext2/dalvik-cache/$file $file
> fi
fi
Syntax error: "fi" unexpected (expecting "then")
Click to expand...
Click to collapse
heh, nice one, indeed I was missing the "then" after the "if" :silly:
El_Dark said:
heh, nice one, indeed I was missing the "then" after the "if" :silly:
Click to expand...
Click to collapse
So then, lol, is like this?
rm $file
ln -s /data/sdext2/dalvik-cache/$file $file
then
done
sgdva said:
So then, lol, is like this?
rm $file
ln -s /data/sdext2/dalvik-cache/$file $file
then
done
Click to expand...
Click to collapse
nope, it's like this:
Code:
for file in somefile*
do
if [ blablabla ]
then
some actions
fi
done
that's it
El_Dark said:
nope, it's like this:
Code:
for file in somefile*
do
if [ blablabla ]
then
some actions
fi
done
that's it
Click to expand...
Click to collapse
I'm not quite sure what you mean by "some actions" is this a command?
This is how I typed it
> if [! -h $file]
if [! -h $file]
> cp $file /data/sdext2/dalvik-cache/
cp $file /data/sdext2/dalvik-cache/
> rm $file
rm $file
> ln -s /data/sdext2/dalvik-cache/$file $file
ln -s /data/sdext2/dalvik-cache/$file $file
> then
then
> some actions
some actions
> fi
fi
> done
done
[!: not found
some: not found
[!: not found
cp: '[email protected]@[email protected]' and '/data/
sdext2/dalvik-cache/[email protected]@[email protected]
ex' are the same file
El_Dark said:
Code:
su
cd /data/
ls (make sure here that you have an sdext2 directory, if not, it means Link2SD is not installed properly)
cd sdext2
ls (make sure that you have a dalvik-cache directory in this place, if not, start Link2SD for a
cd /data/dalvik-cache/
for file in data*
do
if [! -h $file] (we make sure it's not a symlink already, you don't want looping links!!!)
[U][B]then[/B][/U]
cp $file /data/sdext2/dalvik-cache/
rm $file
ln -s /data/sdext2/dalvik-cache/$file $file
fi
done
Click to expand...
Click to collapse
quoting myself
El_Dark said:
quoting myself
Click to expand...
Click to collapse
Oh ok, done
For what I can understand everything is supposed to be linked right? hence this is shown "! not found"?
But I'm still not getting why randomly the SSlauncher is not working in some reboots -and when this happens my link2SD gets vanished too and the message low storage is shown-.
Should I make this everytime that happens? -if it happens again?-
Code:
> if [! -h $file]
if [! -h $file]
> then
then
> cp $file /data/sdext2/dalvik-cache/
cp $file /data/sdext2/dalvik-cache/
> rm $file
rm $file
> ln -s /data/sdext2/dalvik-cache/$file $file
ln -s /data/sdext2/dalvik-cache/$file $file
> fi
fi
> done
done
[!: not found
sgdva said:
Oh ok, done
For what I can understand everything is supposed to be linked right? hence this is shown "! not found"?
But I'm still not getting why randomly the SSlauncher is not working in some reboots -and when this happens my link2SD gets vanished too and the message low storage is shown-.
Should I make this everytime that happens? -if it happens again?-
Code:
> if [! -h $file]
if [! -h $file]
> then
then
> cp $file /data/sdext2/dalvik-cache/
cp $file /data/sdext2/dalvik-cache/
> rm $file
rm $file
> ln -s /data/sdext2/dalvik-cache/$file $file
ln -s /data/sdext2/dalvik-cache/$file $file
> fi
fi
> done
done
[!: not found
Click to expand...
Click to collapse
you shouldn't need to do it every time, mainly when you install new apps, alternatively, you can check the apps' data directories to see which one is consuming a lot of space, you can do that by issuing the commands below:
Code:
su
cd /data/data
du -hc
that should tell you how much space every dir is using (I think, lol)
PS: HIGHLY IMPORTANT!!! You should no longer link dalvik-cache via link2sd with this, or you might experience Force Closes due to the apps' dalvik cache being missing, and I say being missing because if you link a dalvik-cache file that's already linked, Link2SD might move the link and overwrite the physical file, and you'll have a symlink loop
Let's face it, these tablets have had a good run but they're just unusably slow and laggy with any remotely modern version of android. Unfortunately going back to stock is not the simplest in 2022, especially if you've tried one of the more extreme android installs which wipes WebOS and rebuilds the partition table. I spent the morning collecting files and putting together a process from about 25 different websites dating back to 2012. The most comprehensive guide I found was Here but it still didn't fully work for me and some commands had to be done differently, particularly when rebuilding the partitions.
Keep in mind I wasn't kidding when I called this the nuclear option. If you can use any other less extreme method you probably should. This one is a risky pain and basically boils down to nuking the whole thing from orbit before rebuilding the partitions line by line by hand in a terminal.
Necessary files
Everything can be found in this mega folder
ACMEUninstaller2
Novacom
devicetool.jar
WebOS doctor jars (versions 3.0.0 and 3.0.5 in conjunction with devicetool should let you skip the now broken WebOS activation step)
7zip or similar program that can open jar files
Recovery image (nova-installer-image-topaz.uimage)
Java
WebOS quick install
Setup
Make sure Java is installed and working on your system
Make sure your touchpad is fully charged
Open Novacom files.zip and find the right version for your architecture. Odds are that's win-64. If you're on linux check your distro's repos first
Reboot (esp if you're on windows)
Find the Palm, Inc (lowercase L, capital i) folder. On windows this defaults to c:/Program Files/Palm, Inc
Place nova-installer-image-topaz.uimage in your Palm, Inc folder
Place ACMEUninstaller2 in your Palm, Inc folder
Boot your touchpad into WebOS recovery mode, either via bootloader or by holding power+volumeup (can take up to ~30secs)
Open a terminal window and navigate to your Palm, Inc folder
Run one of the below commands. THIS IS THE POINT OF NO RETURN.
Windows: novacom.exe boot mem:// < ACMEUninstaller2
Mac: ./novacom boot mem:// < ACMEUninstaller2
You should see a bunch of text scrolling and two images of a penguin around the top to one side. When it's finished it will warn you there's nothing installed it recognizes.
Try to reboot into recovery mode. You will probably get an exclamation mark with www.palm.com/ROM below it, or just the HP logo
In the Palm, Incterminal execute the below command (capitalization matters):
novacom boot mem:// < nova-installer-image-topaz.uimage
Navigate your terminal to the terminal subfolder and execute novaterm.bat
A small java window named "NovaTerm:" should pop up on your screen
In the NovaTerm: window click file and then connect
Another popup should appear titled Select device to connect with a really long string of letters and numbers ending in (usb, topaz-linux) in it. Click OK
If not check the dropdown arrow, make sure your USB is connected, reboot if all else fails and try again
Now that NovaTerm:says it's connected go back to your terminal and execute the below:
Windows: novacom -t open tty://
Everything else: novaterm should have been enough
Your terminal should now say [email protected]:/# or the like. There may be some extra gibberish if you pressed an arrow key or something.
Now you need to rebuild all your partitions. Execute ONE of the code blocks below these instructions in exact order, one line at a time. You should not see any errors about something being mounted or the like. If you do reboot your touchpad and try to restart from step 13, that's what I did.
Once that is done try to reboot into recovery mode again, you'll probably only get the HP logo instead of the big USB symbol.
Open a new terminal window and navigate to wherever you're keeping the WebOS Doctor jar files
start WebOS doctor 3.0.0 (the only version that can deal with partition issues) from inside the terminal so you can see the output: java -jar webosdoctorp300hstnhwifi_customhpactivationbypass.jar
Don't touch the WebOS doctor window. Moving it to other monitors seems to break it for some reason.
If you see errors where it's trying to find the device and can't try unplugging/replugging the touchpad. If that doesn't work try rebooting. One person said uninstalling novacom at this point and letting WebOS reinstall the drivers fixed it. It seems hit or miss if there's weird USB detection issues on Win10.
WebOS doctor should complete without issues and have you reboot.
When the touchpad successfully reboots it'll ask start asking you for a language and first time activation. HP's master servers are down, this won't work. Reboot into recovery again
Navigate your terminal to wherever you're keeping devicetool.jar and execute it: java -jar path/to/devicetool.jar
Your terminal should say "found device: topaz-bootie" and then talk about configuring things and volumes for a while.
Once the terminal says Device is ready. reboot once final time.
That should be it. Once you've got everything installed and WebOS up and running there's still a few steps needed to deal with the lack of auth servers and expired certificates.
Enable developer mode by putting webos20090606 into the "Just Type" bar on the homepage and hitting enter
Run WebOS-Quick-Install-4-7-2.jar just as if it were a normal application (no need for terminal). It's basically a replacement app store that runs on the PC.
You should see the HP Touchpad recognized by WebOs Quick Install. If it is click the globe on the right side of the app's window
Search for "Preware" in the popup (you need to click the magnifying glass after typing)
Install Preware, which is a replacement app store that runs on the touchpad itself
32gb touchpad partitions
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
dd if=/dev/zero of=/dev/mmcblk0p14 bs=1024 count=1000
lvm.static pvcreate /dev/mmcblk0p14
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static vgcreate -s 8M store /dev/mmcblk0p14
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static lvcreate -l 71 -i 1 -M y --major 254 --minor 0 -n root store
lvm.static lvcreate -l 8 -i 1 -M y --major 254 --minor 1 -n var store
lvm.static lvcreate -l 2 -i 1 -M y --major 254 --minor 2 -n update store
lvm.static lvcreate -l 3 -i 1 -M y --major 254 --minor 3 -n log store
lvm.static lvcreate -l 32 -i 1 -M y --major 254 --minor 4 -n mojodb store
lvm.static lvcreate -l 17 -i 1 -M y --major 254 --minor 5 -n filecache store
lvm.static lvcreate -l 3523 -i 1 -M y --major 254 --minor 6 -n media store
lvm.static lvcreate -l 64 -i 1 -M y --major 254 --minor 7 -n swap store
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
mkdosfs -f 1 -s 64 /dev/store/media
16gb touchpad partitions
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
dd if=/dev/zero of=/dev/mmcblk0p14 bs=1024 count=1000
lvm.static pvcreate /dev/mmcblk0p14
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static vgcreate -s 8M store /dev/mmcblk0p14
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
lvm.static lvcreate -l 71 -i 1 -M y --major 254 --minor 0 -n root store
lvm.static lvcreate -l 8 -i 1 -M y --major 254 --minor 1 -n var store
lvm.static lvcreate -l 2 -i 1 -M y --major 254 --minor 2 -n update store
lvm.static lvcreate -l 3 -i 1 -M y --major 254 --minor 3 -n log store
lvm.static lvcreate -l 32 -i 1 -M y --major 254 --minor 4 -n mojodb store
lvm.static lvcreate -l 17 -i 1 -M y --major 254 --minor 5 -n filecache store
lvm.static lvcreate -l 1618 -i 1 -M y --major 254 --minor 6 -n media store
lvm.static lvcreate -l 64 -i 1 -M y --major 254 --minor 7 -n swap store
lvm.static vgscan --ignorelockingfailure
lvm.static vgchange -ay --ignorelockingfailure
mkdosfs -f 1 -s 64 /dev/store/media
Troubleshooting
If your touchpad's home button has an LED blinking from side to side the battery isn't charged enough. Use the stock charger if available and leave it until it boots itself up. This could potentially take days. Mine only took about 12 hours.
If instead of recovery mode you get either a plain HP logo or an exclamation mark with www.palm.com/ROM below it this means your disk is wiped and there isn't even a recovery or anything. You'll need to use novacom to force nova-installer-image-topaz.uimage onto the touchpad and then connect to it externally using the novaterm utility. Once you run ACMEUninstaller2 this is the expected result.
If you're getting errors about the exclusivity of mmcblk0p14 and asking if it's mounted something went weird while running all of the partitions, try rebooting and starting again.
If you want to download the original WebOS doctor files you need to edit your hosts file and add 195.22.200.42 downloads.help.palm.com
A list of all the resources I used to compile this:
https://hroy.eu/tips/webos-touchpad-restore/ (massive credit to Hroy here, this is by far the most complete guide though it still needed tweaks to the partition rebuilding commands)
Code:
https://www.webos-internals.org/wiki/WebOS_Doctor_Versions
https://forum.xda-developers.com/t/q-touchpad-seems-bricked.1971859/page-2#post-57616293
https://www.webos-internals.org/wiki/How_To_Recover#Doctor_disconnects_at_8.25
https://www.webosarchive.org/docs/activate/
https://forums.webosnation.com/hp-touchpad/330977-how-restore-hp-touchpad.html
https://pivotce.com/2015/06/24/tip-how-to-bypass-activation/
https://pivotce.com/2015/12/13/the-ultimate-bypass-activation-tool/
https://forums.webosnation.com/hp-touchpad/329655-hp-tp-server-error.html
https://forums.webosnation.com/hp-touchpad/317164-activation-bypass-touchpad.html
https://forum.xda-developers.com/t/need-help-webos-fails-at-8-for-hp-tp-due-to-insufficient-free-extents-0-in-volume.3275076/
https://forum.xda-developers.com/t/solved-bricked-and-webos-doctor-wont-help.1564938/
https://forums.webosnation.com/hp-touchpad/325404-recurring-maps-download-failed-error-2.html
https://forum.xda-developers.com/t/guide-factory-condition-restoration-downgrade-to-webos-3-0-0.1426244/
https://forums.webosnation.com/hp-touchpad/332616-getting-restarted-touchpad.html
https://forums.webosnation.com/canuck-coding/274461-webos-quick-install-v4-6-0-a.html
https://forum.xda-developers.com/t/tools-touchpad-toolbox-updated-2015-02-25.2756314/page-4#post-52922166
[MEDIA=youtube]VP-FH6fS2GI[/MEDIA]
[MEDIA=youtube]wFAIJiS8g4o[/MEDIA]
https://forum.xda-developers.com/t/rom-guide-how-to-install-android-on-the-hp-touchpad-the-easy-way.2147284/#post-37965549
https://forums.webosnation.com/hp-touchpad/309309-hp-touchpad-booting-issues.html
https://www.rootzwiki.com/threads/the-official-fix-your-touchpad-8-12-stopped-no-sd-opps-reformat-crap-thread.14249/
https://forum.xda-developers.com/t/guide-video-how-to-bypass-webos-activation-on-the-hp-touchpad.3636750/
https://pivotce.com/2015/06/15/tip-edit-your-hosts-file-for-access-to-old-palm-servers/
hi thanks for the guide,
I agree with you android roms lag quite.
Tired too I restored webOs ,having many of your problems, but unfortunately it is a dead operating system.
Despite the fluidity there is no way to use it. I will go back to android testing all the roms.
Unfortunately this tablet is of its age