[SOLVED]help!! emergency plz :( - Optimus One, P500, V General

hey guyz my phone got stuck in emergency mode while flashing new baseband....
at first the flashing software got stuck on arss burning for over 10mins then it says time out...and the software is not exiting it says you cannot close the program until write have completed to all phone...
i have disconnected my USB and now it is booting into emergency mode no recovery nothing
EDIT: SOLVED
btw if this will happen to u sometime then this is what i did---
turn off ur phone and take out the battery then hold vol up+back key and insert usb while hloding keys mentioned
then it will detect ur phone and goes into emergency mod and then start baseband flashing tool and select baseband file and and start flashing baseband it will start the process from where it was interrupted

In the guide to flashing baseband it says you can reflash from emergency mode. I suggest you give this a try. Else maybe boot into recovery and try flashing from there.

cornelha said:
In the guide to flashing baseband it says you can reflash from emergency mode. I suggest you give this a try. Else maybe boot into recovery and try flashing from there.
Click to expand...
Click to collapse
it isn't booting into recovery only emergency mod

it happened to me 2 weeks ago. i think i unplugged my phone and removed the battery then reinsert it and power on the phone.
or you can try this:
1. connect your phone in emergency mode to the windows pc.
2. check the device manage, to see if there any lg hardware there, don't run the lg update tool now, and you should previously install the lg driver first
3. if you see the 3 lg hardwares, disable the modem one, i found this one make the connection dosen't work when run the lg update tool in emergency mode.
4. just run the lg update tool, it will detect you phone and update itself, even it stop at 4%, if you get luck, you can wait it finish or disconnect the phone, your fastboot should be back.

Don't disconnect phone
Close lgmdp and restart lgmdp and it will begun once again from where it stopped

usb driver are there on my pc it is not showing in device manager and i tried kdz updater as well it says phone not found

cure25 said:
Don't disconnect phone
Close lgmdp and restart lgmdp and it will begun once again from where it stopped
Click to expand...
Click to collapse
i disconnected my phone because it isn't allowing me to exit lgmdp program

gurpreet9080 said:
i disconnected my phone because it isn't allowing me to exit lgmdp program
Click to expand...
Click to collapse
U should have not disconnect it. U can exit lgmdp frm task manager

any help plz,now the problem is that i can't connect my phone to pc,if i can do that i can update via kdz

cure25 said:
U should have not disconnect it. U can exit lgmdp frm task manager
Click to expand...
Click to collapse
now is there any way

gurpreet9080 said:
now is there any way
Click to expand...
Click to collapse
May be u can again try lgmdp to flash rom if it detects your phone-in
http://forum.xda-developers.com/showthread.php?t=1324105

cure25 said:
May be u can again try lgmdp to flash rom if it detects your phone-in
http://forum.xda-developers.com/showthread.php?t=1324105
Click to expand...
Click to collapse
nopz,thats the only problem that it isn't detecting

forum.xda-developers.com/showthread.php?t=1226470May be u can chk out this thread

gurpreet9080 said:
nopz,thats the only problem that it isn't detecting
Click to expand...
Click to collapse
I had a similar problem...
all u need to do is..
restart PC..
open lgmdp and set it up as u did before for changing baseband
now connect phone in emergency mode
it will be detected..
then start the lgmdp process... it will start from where it left out and will get completed...
DO NOT REMOVE BATTERY OR YOUR PHONE IS BRICKED
Press THANKS if I helped..
Sent from my LG-P500 using xda premium

thanx guys i was able to connect my pc and it is working now
thanx to allllllll
thanx alot

gurpreet9080 said:
thanx guys i was able to connect my pc and it is working now
thanx to allllllll
thanx alot
Click to expand...
Click to collapse
If it's solved! Then put a sign [SOLVED] so that it will be cleared..
Sent from my LG-P500 using xda premium

dnle71 said:
If it's solved! Then put a sign [SOLVED] so that it will be cleared..
Sent from my LG-P500 using xda premium
Click to expand...
Click to collapse
yupz,done.....

gurpreet9080 said:
yupz,done.....
Click to expand...
Click to collapse
Also do mention what did the trick for u so that it benefits other users too...
Optimus one
CM 6.5.8
Press THANKS if I helped...

Remove battery WHILE IN EMERGENCY = PERFECT BRICK
Sent from my LG-P500 using Tapatalk

androidusero1p500 said:
Remove battery WHILE IN EMERGENCY = PERFECT BRICK
Sent from my LG-P500 using Tapatalk
Click to expand...
Click to collapse
i did that almost 10times
and it is working absolutely fine

Related

Help please My sgs2 i9100,stuck on logo Samsung galaxs s2,

Dear Brother help me please ,i try to download mod ,but the Odin is not detect my phone,i tired try and try so many time,i got this is, since i upgraded to ics 4.0.4 XWLPT,Any solution please
Can u get into recovery
Sent from my GT-I9100 using xda premium
xxrobxx said:
Can u get into recovery
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
yes i can enter to recovery... and when phone conected to pc,pc is not detect.......any idea??????????
if u have usb jig if not then buy from ebay. then try to enter download mode after that things things will be easy
or as u said u can access recovery ,download cm9 then copy to sdcard using mount and storage option in recovery and flash it
when you connect your phone to pc in download mode, does windows detect it?
Did you even install the Samsung mobile USB drivers?
Mod Edit: In english please or with a translation attached...
OK I'm very sorry about this, mod.. I was so lazy to read details of rules & i was meaning a too early shortcut way to my native friend...
@Badung : I think your problem is easy if u really can enter either recovery and/or download mode. Just flash it with official ROM by Intratech Odin 3 v.1.85 or custom ROM via cwm. I guess it couldn't detected by your PC coz u use wrong & mismatch Odin version. That ver I suggested was an easy match to gs2. U can contact me by whatsapp at 0896-3167-8254. I'm also an indonesian. Maximize your 'search' feature in XDA. Good luck!
In English...
vikas776 said:
if u have usb jig if not then buy from ebay. then try to enter download mode after that things things will be easy
or as u said u can access recovery ,download cm9 then copy to sdcard using mount and storage option in recovery and flash it
Click to expand...
Click to collapse
I have no usb jig..... U said CM9 Night Build..i ll try..
Sent from my GT-I9100 using xda premium
allyourbase said:
Did you even install the Samsung mobile USB drivers?
Click to expand...
Click to collapse
Yes i have...
Sent from my GT-I9100 using xda premium
alvin14 said:
when you connect your phone to pc in download mode, does windows detect it?
Click to expand...
Click to collapse
Yes bro... PC is not detect anything from my mobile, now i do transfer some file using cardreader...
Sent from my GT-I9100 using xda premium
alvin14 said:
when you connect your phone to pc in download mode, does windows detect it?
Click to expand...
Click to collapse
Yes windows is not detect my phone, if i need some file to transfer i have to use card reader..
Sent from my GT-I9100 using xda premium
Try this...:good:
Switch off ur phone and now connect ur phone to PC and (HOLD ) press Volume down + Power button + Home button and see if ur phone detects it..or else install kies in ur pc , so that it will install USB drivers for ur phone. Then unistall kies because kies and odin are eneimes...
Saravanashines said:
Try this...:good:
Switch off ur phone and now connect ur phone to PC and (HOLD ) press Volume down + Power button + Home button and see if ur phone detects it..or else install kies in ur pc , so that it will install USB drivers for ur phone. Then unistall kies because kies and odin are eneimes...
I have no kies.....i try to reinstall my windows on my laptop...mey be could slove the problem.
Click to expand...
Click to collapse
You need to install Kies as it comes with necessary drivers! You dont need to reinstall your OS...
Sent from my Galaxy S2 GT i9100
1. Download this
http://www.nirsoft.net/utils/usb_devices_view.html
2. Run USBDeview, find all devices related to Samsung and uninstall it.
3. Install Samsung USB Drivers
http://forum.xda-developers.com/showthread.php?t=1655286
4. Run ODIN first, get your phone into download mode and then connect it to your PC.
5. At the driver installation dialog, click on "Skip obtaining drivers from windows update".
Hope it helps.
badung81 said:
Dear Brother help me please ,i try to download mod ,but the Odin is not detect my phone,i tired try and try so many time,i got this is, since i upgraded to ics 4.0.4 XWLPT,Any solution please
Click to expand...
Click to collapse
Have u done w/ it bro? See my edited 1st reply..
Sent from my GT-I9100 using xda app-developers app
try to unisnstall /reinstall samsung drivers again, or try it on another pc

[XS] Is going wild

Hello all.
For last 2 days my Xperia S is acting strange.
1: no usb connection to pc; mtp, flash mode..., nothing ( I tried on other pc's, other usb cables
2: media volume stuck at half. Going down and up but till half only.
I did restore factory settings = nothing
Any suggestion?
Thanks in advance.
Sent from my LT26i using xda app-developers app
Try,taking out the battery and than try to put it into flash/fastboot mode.And make sure to try all button configuration....
Hit Thanks if I helped
DekinGBar said:
Try,taking out the battery and than try to put it into flash/fastboot mode.And make sure to try all button configuration....
Hit Thanks if I helped
Click to expand...
Click to collapse
I am not presing thanks ..... becuase havent worked
Is entering in flash mode ... but my pc ( others ) is not seeing it. I hope u understand me '
are you on stock or in custom rom?
Stock
Sent from my LT26i using xda app-developers app
spinky360 said:
I am not presing thanks ..... becuase havent worked
Is entering in flash mode ... but my pc ( others ) is not seeing it. I hope u understand me '
Click to expand...
Click to collapse
I wouldn't say thanks because you can't actually take your battery out
Tapatalked Xperia S
Who says that you cant? I took it for a few times till now. Is very easy
Sent from my LT26i using xda app-developers app
Ben36 said:
I wouldn't say thanks because you can't actually take your battery out
Tapatalked Xperia S
Click to expand...
Click to collapse
Just tell me that you are joking...
Hit Thanks if I helped
My phone is possessed ... im stoping Wi-Fi ( because i have free data ) and after 20-30 sec is showing me that wireless network found [ LOOOOL ]. Im gooing in setings -> Stoping again the wi-fi .,.. after 20 sec ... again.
Any new sugestions ?
So there is no way to flash ROM???
Hit Thanks if I helped
DekinGBar said:
So there is no way to flash ROM???
Hit Thanks if I helped
Click to expand...
Click to collapse
1st: my pc ( and others ) are not detecting him ( phone )
2nd: i dont have CWM installed ( im searching to see how to do " adb wireless " )
3th: some one have to put a full back up after ther ROM ( preferabil stock - un-touch ) in CWM so i can install it
....
I can enter in flash mode but is stay connected in flash mode for 5 sec ... after is restarting bcause ther is no connection with the pc ...
Windows 7 on all these pc's?
Tapatalked Xperia S
Ben36 said:
Windows 7 on all these pc's?
Tapatalked Xperia S
Click to expand...
Click to collapse
No.... 2 windows Xp ... One Ubuntu and a 7/32
Hmm...strange case really.I will try to find a sloution...just tell me your bootloader is locked right?
Hit Thanks if I helped
Yeap...
Sent from my LT26i using xda app-developers app
spinky360 said:
1st: my pc ( and others ) are not detecting him ( phone )
2nd: i dont have CWM installed ( im searching to see how to do " adb wireless " )
3th: some one have to put a full back up after ther ROM ( preferabil stock - un-touch ) in CWM so i can install it
....
I can enter in flash mode but is stay connected in flash mode for 5 sec ... after is restarting bcause ther is no connection with the pc ...
Click to expand...
Click to collapse
I had the same problem with the phone not staying.in flash or fastboot you need to download sony drivers,from there unlock bootloader site. Extractt the. Ini file hard reset ur phone .
On ur pc open device manager
Connect phone into fastboot
On device manager your phone should show as fastboot with a error triange double click quickley before your phone reboots
Click update driver
Select manually
Click show all
Click have disk
Find the . Ini
Dont click next yet
Hard reset phone and reconect as fastboot
Click next all should install ok
If you get error you need to turn digital signing off
You can google this
Phone should now fastboot allowing you to install stock ftf using flashtool.
All data will be lost
Sent from my ST27i using xda app-developers app
nosmaster said:
I had the same problem with the phone not staying.in flash or fastboot you need to download sony drivers,from there unlock bootloader site. Extractt the. Ini file hard reset ur phone .
On ur pc open device manager
Connect phone into fastboot
On device manager your phone should show as fastboot with a error triange double click quickley before your phone reboots
Click update driver
Select manually
Click show all
Click have disk
Find the . Ini
Dont click next yet
Hard reset phone and reconect as fastboot
Click next all should install ok
If you get error you need to turn digital signing off
You can google this
Phone should now fastboot allowing you to install stock ftf using flashtool.
All data will be lost
Sent from my ST27i using xda app-developers app
Click to expand...
Click to collapse
From where fast boot ? I have locked bootloader !!! And i dnt know why you are tellng to to like this! You havent read ? The phone is working grate ( except that is possessed ) I can eneter in Flashmode but PC is not doing the smallest thing ( like ding, fund, connected, unreconized etc... Hardware ) ....
I checked the USB Port -OK everthing is ok
I MANAGED to instal CWM!!!!!
Can someone put a full backup after a stock 45 -50 ( ics ) made with CWM ? THANK YOU IN ADVANCE !!!!
Appoligys didnt read lpck bootloader wherr i,say use,fastboot to install drivers swap for flash mode and then try to repair
I didnt ask you to like my post at all
If you have cwm make a full,backup with cwm
Open device manager turn flash mode on check to see when phone is shown it dosnt have error triange,if it doee,deleate drivers and then,try to repair phone with pc suite
Move backup to pc
Reinstall cwm after its done
And restore data from backup
Sent from my ST27i using xda app-developers app
nosmaster said:
Appoligys didnt read lpck bootloader wherr i,say use,fastboot to install drivers swap for flash mode and then try to repair
I didnt ask you to like my post at all
If you have cwm make a full,backup with cwm
Open device manager turn flash mode on check to see when phone is shown it dosnt have error triange,if it doee,deleate drivers and then,try to repair phone with pc suite
Move backup to pc
Reinstall cwm after its done
And restore data from backup
Sent from my ST27i using xda app-developers app
Click to expand...
Click to collapse
I dont think you understand me rigth ?!
The phone is WORKING! -> Flashmode working ... But when i plug USB ----- Nothing ... and when im saying nothing ... nothing ... i tryed on 5 pc's. 3 USB cables... etc.... etc In device manager is not apearing at all ! in non of the pcs
Thats why i asked some one to put a full backup for it so i can transfer it via Wi-Fi and to install it ok CWM ...
If the pc wont recognice it at all sounds like one of the pins has beem lifted from the maim board have you looked at sending it back under warranty
Sent from my ST27i using xda app-developers app

[Q] my phone doesnt turn on

i ve tried to update my xperia u with flash tool but it failed .now the phone stops on sony logo and my pc wont detect it .tried pc companion and seus but they cant detect it.plz help :/
antokkns said:
i ve tried to update my xperia u with flash tool but it failed .now the phone stops on sony logo and my pc wont detect it .tried pc companion and seus but they cant detect it.plz help :/
Click to expand...
Click to collapse
Try restore it using flashtool??
Sent from my C6603 using xda app-developers app
Sherwinnn said:
Try restore it using flashtool??
Sent from my C6603 using xda app-developers app
Click to expand...
Click to collapse
yes, flashtool doesnt detect the phone either ... any other suggestions ?
remove battery
reinsert battery
dont try to turn on...
press volume down and connect to flashtool... it will detect
drsanket_xperia_u said:
remove battery
reinsert battery
dont try to turn on...
press volume down and connect to flashtool... it will detect
Click to expand...
Click to collapse
just tried it. nothing happened again,still cant detect it... ;(
recharge the battery plz
drsanket_xperia_u said:
recharge the battery plz
Click to expand...
Click to collapse
battery is charged ,still phone get stuck at sony logo and it cant be detected ...
antokkns said:
battery is charged ,still phone get stuck at sony logo and it cant be detected ...
Click to expand...
Click to collapse
Can enter flashmode or fastboot??
Sent from my C6603 using xda app-developers app
Sherwinnn said:
Can enter flashmode or fastboot??
Sent from my C6603 using xda app-developers app
Click to expand...
Click to collapse
no i can not.
antokkns said:
no i can not.
Click to expand...
Click to collapse
k ...
jz tell me how are u trying to connect in flashmode...
plz tell in detail...its necessary so dun get angry
drsanket_xperia_u said:
k ...
jz tell me how are u trying to connect in flashmode...
plz tell in detail...its necessary so dun get angry
Click to expand...
Click to collapse
holding volume down while im plugging the phone on the pc via usb. imnot getting angry and i really appreciate that u are trying to help mate.
Switch off and try with volume up, in flashtool use fastboot. See if the led turns violet or similar color.
noyket slabs
matood said:
Switch off and try with volume up, in flashtool use fastboot. See if the led turns violet or similar color.
Click to expand...
Click to collapse
i tried with volume up fast boot , led turned to blue but still pc wont detect the phone... :/
Do you have the drivers installed for fastboot and fastboot sometimes I have to reinstall after a bad flash
And double check that you have the right ftf for your phone because people have flashed the wrong one before
Sent from my LT22i using xda app-developers app
are u already install flashtool driver for xperia u?
CONdemmedNORmal said:
Do you have the drivers installed for fastboot and fastboot sometimes I have to reinstall after a bad flash
And double check that you have the right ftf for your phone because people have flashed the wrong one before
Sent from my LT22i using xda app-developers app
Click to expand...
Click to collapse
i ve installed flashtool xperia u drivers and the ftf is ok for my phone since its the official 4.0.4 indian firmware for st25i.
Have you tried installing SUS (Sony update service)? And do a repair on that? It might detect your phone.
Sent from my ST25i using xda premium
antokkns said:
i ve installed flashtool xperia u drivers and the ftf is ok for my phone since its the official 4.0.4 indian firmware for st25i.
Click to expand...
Click to collapse
Please follow the instructions :
1.Turn off the phone
[Do not connect it to the computer]
2.Open flashtool and select flashmode
3.Select the firmware and click flash.
4.Connect your phone when the screen shows the prompt with the diagrams
[By pressing volume down ,don't release the button]
5.If everything goes well the flashing will proceed.
The sequence of steps is important.I softbricked my friend's XU by following the wrong sequence(Stuck at Bootlogo and led flashes once when you try to connect in flash or fastboot mode).Following the correct sequence unbricked it....
AKA#1 said:
Please follow the instructions :
1.Turn off the phone
[Do not connect it to the computer]
2.Open flashtool and select flashmode
3.Select the firmware and click flash.
4.Connect your phone when the screen shows the prompt with the diagrams
[By pressing volume down ,don't release the button]
5.If everything goes well the flashing will proceed.
The sequence of steps is important.I softbricked my friend's XU by following the wrong sequence(Stuck at Bootlogo and led flashes once when you try to connect in flash or fastboot mode).Following the correct sequence unbricked it....
Click to expand...
Click to collapse
ive tried it already,the problem is that pc wont detect my phone... when i connect my phone to pc , phone's led turns , after a few seconds leds are off and phone stucks on sony logo...
antokkns said:
ive tried it already,the problem is that pc wont detect my phone... when i connect my phone to pc , phone's led turns , after a few seconds leds are off and phone stucks on sony logo...
Click to expand...
Click to collapse
Go to flashtool folder, drivers and install drivers for your phone. Then repeat the whole sequence above. It will work.
Sent from my MT27i using xda app-developers app

[Q] Bootloader loop problem (solved)

Hi guys
i have a problem on my Xperia P
Bootloader loop
my phone is rooted , the bootloader is unlocked , and i ve that recovery stuff , but i didn't make any backup
and i didn't install any custom ROMs yet. my Android version is the latest one : 4.1.2 JB ( firmware 6.2.A.1.100 )
how's the problem started
i download a program : called : ROM toolbox or something like this , i found on it ,Theme Manager , i choose a background for the notification area , and i pressed replace , then i pressed reboot , and now when i open it , i get the Xperia Logo , then the JB logo loop
any help plz
(sorry for my English ).
Did you read the warning when opening theme manager?
Sent from my LT22i using xda premium
AndroidNoob69 said:
Did you read the warning when opening theme manager?
Sent from my LT22i using xda premium
Click to expand...
Click to collapse
i dk i'm stupid =_=
any hope for my phone? :'(
Just flash a stock ROM via Flashtool, your device has suffered a soft-brick
Garcia98 said:
Just flash a stock ROM via Flashtool, your device has suffered a soft-brick
Click to expand...
Click to collapse
usb debugging must to be opened to use Flashtool?right
and i can't open it
i also tried to clear cache , everything ,..via CWM but still the same problem
killoi said:
usb debugging must to be opened to use Flashtool?right
and i can't open it
i also tried to clear cache , everything ,..via CWM but still the same problem
Click to expand...
Click to collapse
No USB debugging is irrelevant for flashing.
You need to install flashmode drivers and make dure the phone is off (press volume up + power untill you feel 3 vibrations), Then beging flashing and wait for flashtool to ask you to connect in flash mode (volume down while you connect the USB)
ChikeD said:
No USB debugging is irrelevant for flashing.
You need to install flashmode drivers and make dure the phone is off (press volume up + power untill you feel 3 vibrations), Then beging flashing and wait for flashtool to ask you to connect in flash mode (volume down while you connect the USB)
Click to expand...
Click to collapse
I ll try that
brb
oh thanks so much bro
i <3 you
=)
killoi said:
I ll try that
brb
oh thanks so much bro
i <3 you
=)
Click to expand...
Click to collapse
Keep a Nandroid backup in SD for next time to restore via CWM
Garcia98 said:
Keep a Nandroid backup in SD for next time to restore via CWM
Click to expand...
Click to collapse
yea sure

Need help for nitro a311

Dear Developers,
I need help with my nitro A311
I rooted it with Kingroot App second time,,
then I used SDFIX app and device starts misbehaving,,
So I unrooed it after removing that app..but problem persists,,,
sometimes no launcher works on it and system settings starts crashing again and again -
whenever I install any new app or use system twearking apps like app lock,tasker or gallery locker.
after reboots it works good ,,
But sometimes during reboot it does not start and starts rebooting again and again untill I remove the battery and starts it manually.
can anyone help me know what damage I have done and How to solve this problem,,
Please help.. (sorry for any language mistake )
rajat_singhh said:
Dear Developers,
I need help with my nitro A311
I rooted it with Kingroot App second time,,
then I used SDFIX app and device starts misbehaving,,
So I unrooed it after removing that app..but problem persists,,,
sometimes no launcher works on it and system settings starts crashing again and again -
whenever I install any new app or use system twearking apps like app lock,tasker or gallery locker.
after reboots it works good ,,
But sometimes during reboot it does not start and starts rebooting again and again untill I remove the battery and starts it manually.
can anyone help me know what damage I have done and How to solve this problem,,
Please help.. (sorry for any language mistake )
Click to expand...
Click to collapse
Reflash rom. There must be a problem with system files.
Sahilsinghlodhi said:
Reflash rom. There must be a problem with system files.
Click to expand...
Click to collapse
Thanks for reply sir
but can you please tell how to do with a windows 7 32 bit laptop..
rajat_singhh said:
Thanks for reply sir
but can you please tell how to do with a windows 7 32 bit laptop..
Click to expand...
Click to collapse
What rom you wanna flash??
Sahilsinghlodhi said:
What rom you wanna flash??
Click to expand...
Click to collapse
i want to flash stock rom,,
i have reached the final step by configuring .CPP file in YGDP tool but YGDP tool is not recognising my phone,,
i have another query here...
when we go into recovery mode ,, there is an option "apply update from SD card"
can we directly flash from there..
rajat_singhh said:
i want to flash stock rom,,
i have reached the final step by configuring .CPP file in YGDP tool but YGDP tool is not recognising my phone,,
i have another query here...
when we go into recovery mode ,, there is an option "apply update from SD card"
can we directly flash from there..
Click to expand...
Click to collapse
You must install vcom deivers manually.
http://www.micromaxinfo.com/datahan...ection=mobile-canvas-nitro-a311&file=A311.rar
Open ygdp in compatibility mode for windows xp.
Password:369
Add cpb firmware. (Not explaining how to as u have already done it.)
Click on apply update.
Switch off your phone and connect it. Make sure you hold volume up key before connecting and keep held till you see device in YGDP.
Click on start.
There should be no problem that way.
Sahilsinghlodhi said:
You must install vcom deivers manually.
http://www.micromaxinfo.com/datahan...ection=mobile-canvas-nitro-a311&file=A311.rar
Open ygdp in compatibility mode for windows xp.
Password:369
Add cpb firmware. (Not explaining how to as u have already done it.)
Click on apply update.
Switch off your phone and connect it. Make sure you hold volume up key before connecting and keep held till you see device in YGDP.
Click on start.
There should be no problem that way.
Click to expand...
Click to collapse
i think I have installed drivers ,,
whenever i connects my phone to laptop,,with battery or without battery,, its showing (in device manager)
"MediaTek PreLoader USB VCOM (COM10)" for some time and then disappears,
recovery mode is opening by holding volume up key before connecting phone,,
rajat_singhh said:
i think I have installed drivers ,,
whenever i connects my phone to laptop,,with battery or without battery,, its showing (in device manager)
"MediaTek PreLoader USB VCOM (COM10)" for some time and then disappears,
recovery mode is opening by holding volume up key before connecting phone,,
Click to expand...
Click to collapse
Manually install vcom drivers. Thn try. if still not detecting remove battery tun try. (Vol+ key should be holded while connecting)
Sahilsinghlodhi said:
Manually install vcom drivers. Thn try. if still not detecting remove battery tun try. (Vol+ key should be holded while connecting)
Click to expand...
Click to collapse
installed drivers second time and manually,,still not working
what type of usb cord should be used for flashing ?
rajat_singhh said:
installed drivers second time and manually,,still not working
what type of usb cord should be used for flashing ?
Click to expand...
Click to collapse
Original in the box mmx. Not sure for other cables.
Sahilsinghlodhi said:
Original in the box mmx. Not sure for other cables.
Click to expand...
Click to collapse
Not working with original one
rajat_singhh said:
Not working with original one
Click to expand...
Click to collapse
There is something wrong with drivers. Have u installed in correct path????
Sahilsinghlodhi said:
There is something wrong with drivers. Have u installed in correct path????
Click to expand...
Click to collapse
correct path mean?
I installed them in device manager through add hardware legacy option..
drivers are recognising my phone now but ygdp tool is not..
rajat_singhh said:
correct path mean?
I installed them in device manager through add hardware legacy option..
drivers are recognising my phone now but ygdp tool is not..
Click to expand...
Click to collapse
Is PDAnet working on pc with your phone ???
Sahilsinghlodhi said:
Is PDAnet working on pc with your phone ???
Click to expand...
Click to collapse
that requires USB debugging,,
but my phone struck at boot logo,,
it starts occasionally,, then it's app starts crashing crashing,,, so then I have to remove battery again,,
rajat_singhh said:
that requires USB debugging,,
but my phone struck at boot logo,,
it starts occasionally,, then it's app starts crashing crashing,,, so then I have to remove battery again,,
Click to expand...
Click to collapse
You must have to turn on usb debugging for ygdp to detect your phone i think.
And try spflash tool too.
Sahilsinghlodhi said:
You must have to turn on usb debugging for ygdp to detect your phone i think.
And try spflash tool too.
Click to expand...
Click to collapse
how to turn on developers mode in switch off phone,, and ygdp tool will flash it in that state...
rajat_singhh said:
how to turn on developers mode in switch off phone,, and ygdp tool will flash it in that state...
Click to expand...
Click to collapse
http://forum.xda-developers.com/a310/orig-development/rom-twrp-flashable-micromax-canvas-t3287008
Flash this with twrp.

Categories

Resources