Clockwork Mod Touch - Galaxy S II Q&A, Help & Troubleshooting

Hi Guys,
Need a bit of help here.
I bought the clockworkmod touch yesterday, I flashed it, but when I went into recovery it wasn't touch, so I wiped cache, dalvik cache etc...and then isntalled the update.zip to no avail it said "E: failed to verify whole-signature", I tweeted @clockworkmod, and he said it was because I was using SpeedMod Kernel.
So I moved over to Siyah kernel, installed that fine and restored my data/cache using CWM when it booted. I then try to flash ClockworkMod Touch through ROM Manager, the green bar fills, and then says "Succesfully downloaded ClockworkMod recovery!"
I click ok, and then go to "reboot into recovery" I'm presented with red text that says:
E:missing bitmap password_highlight (code-1),
E: missing bitmap password_confirm_45 (code-1),
E: Missing Bitmap password_retry_45 (code-1)..."
I'm then presented with:
Installing Package...
Opening Update Package
Verifying Update Package...
E:Failed to verify whole-file signature
E:Signature Verification failed.
Installation aborted
I've then gone into three button method, and tried to apply, /sdcard/update.zip and it comes up:
Finding update package
Opening update package
E: Can't open /sdcard/update.zip
(No such file or directory)
Installation aborted
I'm running the following setup:
Model:GT-I9100
Android: 2.3.5
Baseband version: I9100XXK14
Kernel Version: [email protected] #294
Build number: Gingerbread.XWKJ1
I would like it if I could get this fixed without using Odin, as i'm at work most of the time and because of some stupid drive encrytion I can't put my phone in without encrypting it, BSkyB's rules apparently. I have tomorrow off, so I can if neccesary boot my laptop up and fiddle with odin.
Just wanna get this sorted, I purchased this and wanna use it.
Any help is much appreciated.

---

You have to wait until devs add this to their kernels/ roms
Sent from my sgs2 running cm9 using xda app

---

Is there no kernel that can support it?
I actually don't really care which kernel I use, aslong as it 's Stock rom for now, then I may look at new 4.0 roms/kernels when they've been out a good few more months, and when obviously clockwork mod touch is more commonly added to kernels/roms.

---

A guess its Rom Manager as SGS2 does not like it .
As this is an app their is a thread in the applications section .
jje

---

richfreestone said:
Hi Guys,
Need a bit of help here.
I bought the clockworkmod touch yesterday, I flashed it, but when I went into recovery it wasn't touch, so I wiped cache, dalvik cache etc...and then isntalled the update.zip to no avail it said "E: failed to verify whole-signature", I tweeted @clockworkmod, and he said it was because I was using SpeedMod Kernel.
So I moved over to Siyah kernel, installed that fine and restored my data/cache using CWM when it booted. I then try to flash ClockworkMod Touch through ROM Manager, the green bar fills, and then says "Succesfully downloaded ClockworkMod recovery!"
I click ok, and then go to "reboot into recovery" I'm presented with red text that says:
E:missing bitmap password_highlight (code-1),
E: missing bitmap password_confirm_45 (code-1),
E: Missing Bitmap password_retry_45 (code-1)..."
I'm then presented with:
Installing Package...
Opening Update Package
Verifying Update Package...
E:Failed to verify whole-file signature
E:Signature Verification failed.
Installation aborted
I've then gone into three button method, and tried to apply, /sdcard/update.zip and it comes up:
Finding update package
Opening update package
E: Can't open /sdcard/update.zip
(No such file or directory)
Installation aborted
I'm running the following setup:
Model:GT-I9100
Android: 2.3.5
Baseband version: I9100XXK14
Kernel Version: [email protected] #294
Build number: Gingerbread.XWKJ1
I would like it if I could get this fixed without using Odin, as i'm at work most of the time and because of some stupid drive encrytion I can't put my phone in without encrypting it, BSkyB's rules apparently. I have tomorrow off, so I can if neccesary boot my laptop up and fiddle with odin.
Just wanna get this sorted, I purchased this and wanna use it.
Any help is much appreciated.
Click to expand...
Click to collapse
I am also waiting for a fix for your problem, I was about do the same steps you have done, to install the CWM touch from my SGS2, my kernel vesrion is Siyah-V2.6.12 instead.
lets wait for a solution,