On the stock ROM, I can almost fully flash my Fascinate to Cricket (everything works but Market and applications using data, everything works with my Droid on the same plan, including Market and applications). I think the last piece is causing Market/Apps to not work. I need to do the following
cd c:\android\tools <enter>
adb shell <enter>
mkdir /data/opt/ <enter>
exit <enter>
adb remount <enter>
adb push c:\android\tools\u2nl /system/bin/u2nl <enter>
adb push c:\android\tools\autostart.sh /data/opt/autostart.sh <enter>
Now:
adb shell <enter>
chmod 0755 /system/bin/u2nl <enter>
chmod 0755 /data/opt/autostart.sh <enter>
adb reboot <enter>
Install Autostart from the Market or download it form the bottom of this post and install it. Reboot the phone (sometimes it will take more than 1 reboot) and give the Superuser Permission box a few seconds to pop up. Autostart will be looking for permission. Grant it.
Click to expand...
Click to collapse
The problem is I can't run the mkdir /data/opt/ command because the file system is locked. If I flash to a new ROM, then I can make the directory, but data stops working, and Cyanogen doesn't have a modem mode.
What would be the best Rom to use? Does anyone know which ones have modem-mode available? Or is there a way to unlock the filesystem so I can make that directory?
My bootloader is locked and i recently had my phone rooted with CWM on .42, having installed with SE tweak installer. But i have updated to the newest firmware and either the SE tweak installer is not working for ICS, or i can't boot into recovery. I have spammed every key on the boot but it boots normally, so i think the tweak installer failed; Here is the log ---
adb shell rm /data/local/tmp/*
rm failed for /data/local/tmp/*, No such file or directory
adb push "data/install_cwm" /data/local/tmp/install_cwm
adb push "data/recovery.tar" /data/local/tmp/recovery.tar
adb push "data/chargemon_alter" /data/local/tmp/chargemon
adb push "data/sh" /data/local/tmp/sh
adb push "data/charger" /data/local/tmp/charger
adb shell "chmod 777 /data/local/tmp/install_cwm"
adb shell "su -c '/data/local/tmp/install_cwm'"
/system/bin/sh: su: not found
adb shell rm /data/local/tmp/*
--
There is also a root method for ics which i have tried with no luck... I think its Rootv5.
Can anyone help me get these on my phone. It is completly stock generic Europe
These tweaks are only for Gingerbread for now.
Sent from my Xperia Live using xda premium.
Hi guys
I've imported the SH-06D from Japan and the phone is running great, however I'd like to remove some system apps etc to help speed up the phone (it's still on 2.3.5) and obviously tweak it as well.
I know there is an existing thread on the SH-01D (predecessor to the SH-06D) but I'm wondering if anyone has successfully rooted the SH-06D and if so, is there an (easy) process to do this?
Another reason I want to root, is to install the UI from the upcoming Evangelion Nerv edition of the SH-06D that is due to be released in a few days.
ICS for the SH-06D is just around the corner (due to be released in July) but I'd realy appreciate any help, assistance or tips in rooting the phone as it is now.
Cheers! :fingers-crossed:
Anyone?
:-(
here is a link to root the sh-06d :
http://itsuki.ddo.jp/gadget/index.php?SH-06D
THANK YOU!
Have you tried this method and does it work? Can you assist me in following those directions?
Cheers
interfreak said:
THANK YOU!
Have you tried this method and does it work? Can you assist me in following those directions?
Cheers
Click to expand...
Click to collapse
i haven't tried since i don't have this phone.
i can try to help you if you want.
testnumero said:
i haven't tried since i don't have this phone.
i can try to help you if you want.
Click to expand...
Click to collapse
Thanks mate!
I'm fumbling through the process now - it's a little hard when you are using google translate lol!
OK, I've run through all the steps but..
When I get to the end of the process:
C:\Users\interfreak\Desktop
$ su
su
su: permission denied
:-(
interfreak said:
OK, I've run through all the steps but..
When I get to the end of the process:
C:\Users\interfreak\Desktop
$ su
su
su: permission denied
:-(
Click to expand...
Click to collapse
i don't know what is the problem, try to do steps again.
Tried, same result. :-(
interfreak said:
Tried, same result. :-(
Click to expand...
Click to collapse
i'll ask to translate it
Thanks mate!!! :highfive:
I want to know untill now has SH-06D been rooted?
I wish someone could dump ROM or launcher from SH-06 NERV version:fingers-crossed:
I'm working on the translation for root on Sharp Aquos SH-06D.
Please give me one or two more days!
That is highly impossible, having full root in J Phone are hard enough. Unlocking the bootloader is a wet dream for almost everyone who likes J phone
lightout said:
I want to know untill now has SH-06D been rooted?
I wish someone could dump ROM or launcher from SH-06 NERV version:fingers-crossed:
Click to expand...
Click to collapse
I'm trying to hard reset my SH-06D, but I can't do it via settings-privacy. I can select to wipe, but nothing happens.
Any suggestions?
I got the Nerv edition
Hey man, how did the rooting go? I ordered the Nerv edition of this phone, and I want to root it (mainly to pair my sixaxis controller for psx emulation) but wanted to consult with you first as a precaution.
Here is the a rough translation of the root guide found here:
http://itsuki.ddo.jp/gadget/index.php?SH-06D
Big thanks to testnumero for the help!
Please don't ask me directly for help. I don't own this phone.
A quick look at root
• With root you can freeze preinstalled bloatware and backup application settings and game save data.
• 3D content from /system can be played on other devices and 3DTVs.
Unresponsive apps can be frozen which will help the device run smoother and have a longer battery life.
Applications which are frozen disappear from your drawer making the device look cleaner and keeping your mind at ease.
• The process is similar to the one used for SH-01D.
• If an update patch is released or the Android 4.0 summer update is released then this guide will no longer be of help.
(Make sure your device is the following: Android Ver. 2.3.5 Build No. 01.00.03)
• If your device becomes a paperweight I won’t be held responsible.
• Follow this guide at your own risk.
↑
Preparations – Before you begin
• Install Android SDK and SHARP ADB USB drivers and make to use ADB.
• 「Settings」→「Applications」→「Development」→「USB Debugging」 checked.
• SH-06D and micro USB cable to connect to your PC
↑
Required Files
• Download "shdisphook" from the following link and extract.
http://goo.gl/Bs6Iq
• Download shsdgetroot-omap4.zip from the following link and extract.
http://www1.axfc.net/uploader/File/so/78144
• Download shbootgetroot-su.lzh from the following link and extract.
http://www.mediafire.com/?6i0n32jlwbxe8cp
• Keep all extracted files in the same folder.
↑
Creating files
• Create a file named "shdisphook.bat" in the folder with the extracted files.
Copy and paste the following and save.
adb push onload.sh /data/local/
adb push libsdservice_jni.so /data/local/
adb push shdisphook /data/local/
adb shell chmod 755 /data/local/onload.sh
adb shell chmod 755 /data/local/shdisphook
adb reboot
adb wait-for-device shell /data/local/shdisphook
pause
• Create a file named "oncmd.sh" and put the following in the description.
(Save the line break as LF)
chmod 777 /cache
chmod 666 /cache/recovery
• Replace the contents of the file "installfile.cmd" with the following and save.
adb shell /data/local/shsdgetroot-omap4 -c "/system/bin/mount -o rw,remount -t rootfs rootfs /"
adb shell /data/local/shsdgetroot-omap4 -c "/system/bin/chmod 777 /sbin"
adb push su /sbin
adb push busybox /sbin
adb shell /data/local/shsdgetroot-omap4 -c "/system/bin/chown 0.0 /sbin/su"
adb shell /data/local/shsdgetroot-omap4 -c "/system/bin/chown 0.0 /sbin/busybox"
adb shell /data/local/shsdgetroot-omap4 -c "/system/bin/chmod 6755 /sbin/su"
adb shell /data/local/shsdgetroot-omap4 -c "/system/bin/chmod 755 /sbin/busybox"
adb shell /data/local/shsdgetroot-omap4 -c "/sbin/busybox --install -s /sbin"
adb shell /data/local/shsdgetroot-omap4 -c "/system/bin/chmod 755 /sbin"
adb shell /data/local/shsdgetroot-omap4 -c "/system/bin/mount -o ro,remount -t rootfs rootfs /"
adb push Superuser.apk /data/local/
adb shell /system/bin/pm install -t -f -r /data/local/Superuser.apk
adb shell /system/bin/rm /data/local/Superuser.apk
exit /b
↑
Step 1
• Open command prompt to the folder with the extracted files and navigate to "shdisphook".
Execute "shdisphook.bat". (You can also just double click on the .bat file)
• The device will reboot so just wait for the [Press any key to continue] message to appear.
If more than a few minutes have passed and nothing has appeared then, force close and execute "shdisphook.bat" again.
(When you fail your PC will reboot or your SH-06D WiFi will start. There is a high rate of success when you immediately unlock the lock screen for your device when it goes to sleep.)
↑
Step 2
• Open command prompt and send oncmd.sh to SH-06D to change permissions
adb push oncmd.sh /data/local/oncmd.sh
adb shell chmod 755 /data/local/oncmd.sh
• 「Settings」→「microSD and device storage」→「Unmount microSD」 This will execute the file "oncmd.sh" , which was sent to the device earlier.
(Cancel the message for 「Unmount microSD」)
• Enter the following commands.
adb shell mv /cache/recovery /cache/recovery_
adb shell ln -s /dev/shsd /cache/recovery
• Execute the following adb shell ls -l /cache and if you see the following message you have succeed.
drwxrwx--- root root 2011-11-11 03:39 lost+found
drw-rw-rw- system cache 2012-01-24 10:48 recovery_
lrwxrwxrwx shell shell 2012-03-02 13:24 recovery -> /dev/shsd
• Next execute adb shell ls -l /dev/shsd you should get the following message if you were successful.
crw-rw-rw- system cache 231, 0 2012-04-23 02:01 shsd
↑
Step 3
• Execute adb push shsdgetroot-omap4 /data/local
• Execute adb shell /system/bin/chmod 755 /data/local/shsdgetroot-omap4
• Execute adb shell /data/local/shsdgetroot-omap4 -v -m -u
• The “# “mark will appear there will be no response. Close command prompt for now.
• Execute installfile.cmd
• Check if you have root with the following adb shell→su
↑
After you reboot
• After you reboot you will lose root rights so execute shdisphook.bat→Cancel Unmount microSD →execute installfile.cmd and you should have root again.
The reason why you cannot do a clean wipe or nothing happen is because the recovery section has been move out into another location, causing it to not loading the recovery correctly.
Check with SH-01d part, I have asked similar question there and I revert the recovery in order to wipe the phone..
You need to rearrange the following section like on the sh-01d when you hit this part:
(Following is Original command that you relocated the recovery for root)
adb shell mv /cache/recovery /cache/recovery_
adb shell ln -s /dev/shsd /cache/recovery
And replace with the revert command found on sh-01d thread. You will need to redo all the steps from step 1 to step 2 and STOP AFTER YOU REVERT the RECOVERY.
You should be able to do a full wipe with no issue then. DO NOT POWER DOWN or RESET!!! You will have to REDO it again as it REQUIRES SHDSIHOOK to input shell command.
Hope it helps
waiting！！！！！！！！！！
I Request senior members to help me on this topic coz m a begainer to android m trying to root my cell since last 1 month but always i get an disappointment with 0 result so i request mods and senior members to help me in rooting my phone..
my cell is a made in china cell so i dont have the drivers
here are some more details for ur refference
campany name Aimax
model: R5830i
ANDROID VERSION: 2.3.5
BASEBAND VERSION: BASE_W12.17/sc6820_sp6820/04-20-2012/16:03:42
kernel version:2.6.35.7 [email protected]#9
software version:mocorDroid2.3.5.w12.09.10
hardware version:1.1.0
and one more thing when i connection to pc it shows found new hardware "spreadtrum phone" but it is unable to update the drivers...
Positive replies are always appreciated thanx in advance
Plez help
plez help waiting for your reply...
Rooting China phones in windows and linux
Try one of these:
1. Using linux {Recommended}Install Ubuntu or DebianEither
Install the android-sdk.
dl.google●com/android/adt/adt-bundle-linux-x86-20130717.zip <==x86
dl.google●com/android/adt/adt-bundle-linux-x86_64-20130717.zip <==x86_64
or
Just get the standalone adb and fastboot executables
texasice-cream-sandwich-mirror.googlecode●com/files/adb_fastboot.zipInstall ia32-libsRun this in a terminal
Code:
sudo apt-get install libc6-i386 lib32stdc++6 lib32gcc1 lib32ncurses5
Now download the files required for root and put it in the same folder as adbmir●cr/GDEPZT4VAfter you finish installing the files,
Connect your device with debugging mode enabled
Run
Code:
cd path/to/adb
where "path/to/adb" is the directory of your adb file
Now run
Code:
sudo chmod a+x adb
sudo chmod a+x fastboot
>>Root
Code:
./adb devices
./adb push busybox /data/local/tmp/
./adb push su /data/local/tmp
./adb push Superuser.apk /data/local/tmp
./adb shell
Chmod and run the exploit under adb shell
Code:
cd /data/local/tmp
chmod 755 psneuter
./psneuter
Now re-engage an adb shell to check if the exploit worked.
Code:
./adb kill-server
./adb devices
./adb shell
If you see a # sign, the exploit was was successful. Otherwise repeat from >>Root
Now run these on the same adb shell
Code:
cd /data/local/tmp
./busybox ash
mount -o remount,rw /system
mv /data/local/tmp/su /system/xbin/su
chmod 6755 /system/xbin/su
chown 0.0 /system/xbin/su
mv /data/local/tmp/Superuser.apk /system/app/Superuser.apk
chmod 777 /system/app/Superuser.apk
cp /data/local/tmp/busybox /system/xbin/busybox
chmod 6755 /system/xbin/busybox
Now reboot your device and open up SuperSU. Let it update the binary.
Your device should be rooted. 2. Use Windows + MoboroboMethod 1 {Recommended but hard}
Download Moborobo from
Code:
moborobo●com
This software can Install drivers for many china phones and other branded phones.
After installing Moborobo download the files required for root
Code:
mir●cr/GDEPZT4V
Extract the files to the installation directory of Moborobo.
Code:
C:\Program Files (x86)\Moborobo
Run a CMD window under that directory and type
Code:
xcopy AndroidInterface.exe abd.exe
Connect your device in debugging mode & Open up Moborobo, It will install the drivers.
Keep Moborobo open & Follow the instructions mentioned in >>Root
P.S- the linux commands begin with a "./" remove this in windows or else it won't work. Note: Wherever I mentioned a terminal, the windows equivalent to this would be cmdMethod 2 {Easier}
Download and Install Moborobo just like above and run this under a cmd on that folder
Code:
xcopy AndroidInterface.exe
Also download UnlockRoot or SuperOneClick
To make sure the adb files are same, Copy over
Code:
adb.exe
AdbWinApi.dll
AdbWinUsbApi.dll
to UnlockRoot's tools directory or SOC's ADB directory
Connect your device in debugging mode and open up moborobo.
Now keep Moborobo open and Run UnlockRoot or SOC. Good Luck :good:
(c) Smo0thK, team BL4CKF1R3
Press thanks if I helped you.
Nice tutorial you have posted Smo0thK. Please also comment on the following points.
1) Which tablets have you tried the above methods to get root access. Since most of the tablets in Indian market are from China, same would be the situation in Bangladesh and similar techniques can be used. Please list their Brand and model numbers.
2) I personally use a Penta IS701c which actually is pre-rooted from factory but the su command does not work because configuration is messed up. (# prompt in ADB shell indicates root access) Many of these Chinese tablets come pre-rooted from factory but to get su command working things have to be cleaned up. What is your experience about this.
3) Android 3.1+ devices must support USB Host mode but most of the tablets are lacking support. (Use USB Host Diagnostics app to find out).
Have you found any tablet that supports USB Host mode without a custom kernel.
Best Regards,
Vineet Kumar
I know there has been a lot of tutorials how to root the Xperia X10 mini. But almost a lot of them don't work (for me). But there is one way to root it.
It is very simple, you need to follow the instructions, then it will be easy.
1.) We need to download Android SDK, link: http://developer.android.com/sdk/index.html
2.) We need to download SuperOneClick.rar, link: http://shortfuse.org/
3.) Unzip the SuperOneClick .zip and pull out the su-v3, busybox, Superuser.apk, psneuter, and GingerBreak files, and rename the su-v3 into su, and place all the files in adt-bundle-windows-x86-20130219/sdk/platform-tools. I recommend changing the "adt-bundle-windows-x86-20130219" to something simple like "Android SDK".
4.) Now, you have to use CMD, open it, and type the location of your files, type like this, cd C:/Users/Me/Desktop/Android SDK/sdk/platform-tools.
5.) Now plug in your phone, and make sure your debugging and unknown sources are on.
6.) Now write all the following commands, one at a time!
adb devices
adb push psneuter /data/local/tmp
adb shell
$ cd /data/local/tmp
$ chmod 777 psneuter
$ ./psneuter
adb kill-server
adb devices
adb shell
# mount -o remount,rw -t rfs /dev/block/st19 /system
# exit
adb push busybox /system/bin
adb push su /system/bin
adb install Superuser.apk
adb shell
# chmod 4755 /system/bin/busybox
# chmod 4755 /system/bin/su
# mount -o remount,ro -t rfs /dev/block/st19 /system
# exit
adb reboot
And now u are all done! Your phone will reboot, then download Root Checker, and check if you are rooted.
If you write "adb shell" and you don't get "#" in the ending (not the beginning) but "$" then you have done something wrong, check everything that I wrote. If u have some problems, don't be shy to tell me.
Thanks a bunch, this tutorial was the only one that worked for me. What's more, I saw the procedure step-by-step so I saw exactly what was going on.