I have 4 android devices that cannot connect to the internet, but they connect to the router just fine. I can access the router settings with the devices. I know the network is working because my PC can connect fine via wifi. The devices can connect to other networks fine except mine.
Devices:
LG P500 (ICS 4.0.3)
Samsung P1000 (ICS 4.0.3)
Samsung P6200 (Honeycomb Stock)
Samsung Galaxy Spica (Froyo 2.2.1)
Follow the basic network troubleshooting procedures:
If the PC works, it isn't a routing or DNS problem per se. So, check that the Android devices are getting an IP, that the IP is in the same subnet as the PC, check DNS (my first suspect for your situation), check routing table.
If none of the androids connect and the PC does, it sounds like you have some statically assigned or cached info on the PC but when the Androids connect and pull DHCP (dynamic host info) they are missing some key piece. Again, prime suspects are DNS and default gateway.
If you have a terminal emulator and root access on even one device this is easy. If not you'll need an app to tell you. Network Info II looks ok, I just tried it. Look under the WiFi tab.
Anyway, I think that's where you'll find your problem.
jonasbull said:
Network Info II looks ok, I just tried it. Look under the WiFi tab.
Click to expand...
Click to collapse
Second vote for Network Info II. I've also used Fing to troubleshoot wifi networks. Both of those are essential entries in my toolkit.
Good luck.
Two of the devices(Optimus One and Galaxy Tab) have root and terminal emulator installed. I already checked the devices have the same info with ipconfig on my pc except ip(of cousrse) Default Gateway and DNS are correct. IP has the same subnet on my phone and PC. Tried static but still failed.
That is interesting. You do have mobile networking off, right? Older Android versions sometimes had issues if both were on.
Ok, so does the PC connect to wifi also?
As stated in the OP, the PC also connects via wifi and mobile networking is off on the Androids.
Reboot! Always helps!
If your devices are associated the router, first ping your router's ip (usually 192.168.1.1). Then ping some external ip (like 8.8.8.8). If pings are fine, problem is in DNS.
Could also be some filtering on the router...
Related
hi,
I've linksys wi-fi router model WRT54GH in my home & it has a good amount of signal strength to cover entire area.
My recently bought galaxy S2 is able to identify linksys wi-fi access point & connects too with the IP assigned to it, also at wi-fi settings connected being displayed.
Now when I try to access Internet (any url google/FB), it doesn't connect at all.
I tried almost everything about router configuration, restart etc. but with no success
can someone plz help on this ?
shantanu_d said:
hi,
I've linksys wi-fi router model WRT54GH in my home & it has a good amount of signal strength to cover entire area.
My recently bought galaxy S2 is able to identify linksys wi-fi access point & connects too with the IP assigned to it, also at wi-fi settings connected being displayed.
Now when I try to access Internet (any url google/FB), it doesn't connect at all.
I tried almost everything about router configuration, restart etc. but with no success
can someone plz help on this ?
Click to expand...
Click to collapse
In my case the problem was with frozen "WiFi sharing" in combination with juicy defenders "Location" fearure. It seems such combination is dangerous. Solutin (in my case):
1. defroze
2. remove all wifi networks
3. reboot (for "clean" frozing)
4. make WiFi sharing frozen
5. reboot again just for fun
Try to check your router's MAC address restrictions. In my router, as security, I have to add MAC addresses of each device to share internet. They take IP's, connects etc. but does not have accesses to internet
as above, check that there is no MAC filtering set up.
one other thing it may be is the security settings, if you have a WEP Key to access the router it may need the Hex conversion of your key depending on what level of security you have (64bit or 128bit for example)
shantanu_d said:
hi,
I've linksys wi-fi router model WRT54GH in my home & it has a good amount of signal strength to cover entire area.
My recently bought galaxy S2 is able to identify linksys wi-fi access point & connects too with the IP assigned to it, also at wi-fi settings connected being displayed.
Now when I try to access Internet (any url google/FB), it doesn't connect at all.
I tried almost everything about router configuration, restart etc. but with no success
can someone plz help on this ?
Click to expand...
Click to collapse
Try setting up a static IP address for your phone, I presume your network is a 192.168.1.0, go into router settings and LAN setup, give your phone the address in a static DHCP assignment of 192.168.1.5, or any other address in the same subnet your in. Some SGSII's have problems with dynamic DHCP for some reason, some NS had the same problem too,
Sent from my Sammy Galactic S2 Beastly Device
I have a similar problem and I fix mine temporarily by turning my wifi off, then in wifi settings > advanced, I change wifi sleep policy from 'never' to 'only when the screen is off'. However I have to do this every time I want to use wifi so it can become quite annoying sometimes.
So I can get through however only for a short period of time as it seems as long my Galaxy S2 keeps turning off my wifi even though it's on :/
I had exactly the same issue on Linksys E4200 with my laptop, could connect to network, even to router's attached storage, but not to internet. Restart helped
On SGS2, I couldn't connect to the router at all at first, but fixed this by switching from WPA2/WPA mixed mode access protocol to WPA2 private. But I guess this is not exactly your issue.
SiSL said:
Try to check your router's MAC address restrictions. In my router, as security, I have to add MAC addresses of each device to share internet. They take IP's, connects etc. but does not have accesses to internet
Click to expand...
Click to collapse
Thanks for the suggestion but MAC restriction is already disabled at router
Robsso said:
I had exactly the same issue on Linksys E4200 with my laptop, could connect to network, even to router's attached storage, but not to internet. Restart helped
On SGS2, I couldn't connect to the router at all at first, but fixed this by switching from WPA2/WPA mixed mode access protocol to WPA2 private. But I guess this is not exactly your issue.
Click to expand...
Click to collapse
Yes, you are right this is not an issue for me.
In fact my SG2 being assigned with an IP address from 192.168.1.xx subnet.
Also at a same time my laptop connected with an IP from same subnet able to ping SG2.
OccasionalDroid said:
Try setting up a static IP address for your phone, I presume your network is a 192.168.1.0, go into router settings and LAN setup, give your phone the address in a static DHCP assignment of 192.168.1.5, or any other address in the same subnet your in. Some SGSII's have problems with dynamic DHCP for some reason, some NS had the same problem too,
Sent from my Sammy Galactic S2 Beastly Device
Click to expand...
Click to collapse
My SG2 being assigned with an IP address from 192.168.1.xx subnet.
So I think IP addressing may not be an issue.
Also another thing I tried was, at a same time my laptop connected with an IP from same subnet able to ping SG2.
So wi-fi router may not be an issue here, whats say ???
Even I am facing the same issue at my office network. I am able to connect to the wireless network but if I try to access any app I cannot browse. This is really frustrating looks like some issue with the modem drivers.
I was able to browse on another wifi created virtually by mobile tethering. This looks like a major bug with the current firmware. Another interesting thing to note is that the Wifi network has a hidden SSID and uses WPA2 auth scheme.
I have seen a Galaxy S able to connect to the same n/w without any issues.
Has anyone figured out a solution to this one ?
Hi, thanks for your reply.
I am yet to figure out a solution for this
Even I am also agree on the probable issue with modem driver.
I've D-link modem.
Are you aware of anything about this modem that can be reconfigured to get this worked ... ?? pl let me know
The wifi router at my office is Cisco Aironet 1200 Series, anyone else facing this issue ?
I'm having the same problem at work connecting my SGS2 with v2.3.3 Official Firmware (customized for Orange service provider) to a Cisco Aironet 1130 AP. I can see that the Galaxy authenticates with the AP correctly and gets IP from the DHCP server, but it cannot send or receive any traffic, although the phone stays connected and authenticated. At home, I use an Atheros based Fonera with DD-WRT without any problem.
As I'm the company's network administrator, I will try to further investigate this problem, but it seems like some kind of incompatibility between the devices or misconfiguration ....
Basuk said:
The wifi router at my office is Cisco Aironet 1200 Series, anyone else facing this issue ?
Click to expand...
Click to collapse
try turn off the wifi, turn off the mobile data and turn on the wifi again
It seems the SGS2 sometimes has problems with DNS.
Try a static IP and use 8.8.8.8 as second DNS server, which is a free Google DNS server.
This fixed MY problems
I rooted my SGS2 and voila wifi worked at my office finally I have been able to find a solution.. love my SGS2 the Beast...
I'm having this same problem..
I think I've tried all the solutions above, but one (Sorry - noob question):
Rooted?
is there a firmware patch or something that I should know about?
Anyone got any other ideas?
ETA:
I can connect to hotspots (DHCP) and at home (Have to set it to static tho)
No internet
AP works - Laptop and i8910 (had to set static and advanced settigs etc). I've rebooted it a few times, set DHCP on and off. DHCP seems to be running on the router
viqles said:
I'm having this same problem..
I think I've tried all the solutions above, but one (Sorry - noob question):
Rooted?
is there a firmware patch or something that I should know about?
Anyone got any other ideas?
Click to expand...
Click to collapse
This is an issue with SGS2 with wifi server using authentication protocol TPIK, if you use AES as encryption then it will work without any issues.
That should be a setting in my AP? I can't see it...
If I get a new non-crappy AP is that likely to solve my problem?
ETA:
Ah - that's a WPA thing? Mine only seems to do WEP - is that right?
I have a YP-G70 (galaxy player 5.0), international version. It came with gingerbread 2.3.5, and it was unable to find the adhoc network I've set up in my laptop.
Then I flashed it with rumirand's custom kernel r13 and Meticulus's Foreigner ROM R5.1 (GB 2.3.6), and the problem was still there.
Then I replaced the wpa_supplicant file with the one mentioned in these posts:
http://forum.xda-developers.com/showpost.php?p=22268045&postcount=60
http://forum.xda-developers.com/showthread.php?t=1438334
http://forum.xda-developers.com/showthread.php?t=1377321
(the file that is mentioned is always the same)
Now it detects the adhoc network, but when I connect to it, the wifi status starts looping: connecting -> disconnected -> scanning -> connecting -> disconnected -> ...
Did I miss anything?
Has anyone managed to get adhoc to work on YP-G70 using one of the custom ROMs based on 2.3.6?
Or do I really need to go back to 2.3.5 and use the wpa_supplicant file mentioned above?
Thank you
I have played with some of these wpa_supplicant files recently. The result seems to be hit and miss.
So far I tried connecting to 2 different usb wifi dongo using ad hoc mode. The only successful one is the ad hoc connection to a tp-link wifi dongo using wep mode. This dongo doesn't support wpa.
The other one that failed is a linksys dual band dongo, I can't get a connection with either wep or wpa. The observation is very similar to yours.
Need to try a few other device to see what's wrong or whether it is due to incompatibilities.
By the way, I also tried all the possible security options (open, wep, wpa). Same behavior for all of them, except that the "connecting" step took much longer when using wpa.
Interesting note on incompatibilities. My laptop's wi-fi card is an Intel PRO/Wireless 3945ABG.
I found out that it ends up connecting successfully if I just leave it looping for a while... sometimes it will succeed on the first few attempts, sometimes it takes several minutes.
So far, it only worked in open or WEP. Never got it to work in WPA.
DHCP
Have you tried to use a fixed ip instead of dhcp ?
Yes, that's how I've always had it set up. I don't think there is a way to use dhcp in ad hoc.
Today, I've switched to the Chip v1.5 custom firmware and I just can't get ad-hoc to work at all. No ad-hoc networks are displayed in the wifi settings.
I've tried replacing the wpa_supplicant file with different versions of that file, but it just rendered the wifi completely unfunctional: I turn it on, it goes "scanning...", then it turns itself off automatically after a few seconds. I had to reinstall the firmware in order to get the wifi to work again.
I would really appreciate some help, as I completely rely on an ad-hoc connection to obtain internet access on my SGP when I'm at home. I don't feel like going back to the firmware I was using before, having seen how great this one is.
So you have used static ip? And set it up correctly? Because the wifi connect and disconnect problem is frequent with belkin routers, and is fixed by using static ip usually.
Sent from my YP-G1 using xda app-developers app
Yeah, the IP settings are correct, and I'm using a static IP. I eventually got used to the looping that I mentioned in a post above, and I've lived with that for the past 8 months.
However, as I said in my previous post, I've installed the Chip v1.5 firmware, and now my problem is somewhat different.
Wiz7 said:
I've tried replacing the wpa_supplicant file with different versions of that file, but it just rendered the wifi completely unfunctional: I turn it on, it goes "scanning...", then it turns itself off automatically after a few seconds. I had to reinstall the firmware in order to get the wifi to work again.
Click to expand...
Click to collapse
if you had this happening, it meant the wpa_supplicant you'd tried wasn't compatible with your device. Always backup wpa_supplicant before replacing in in case the new one doesn't work.
Try this wpa_supplicant, it works with my 5.0.
I had the same problem with Ad-hoc networks using windows7 (ie obtaining ip address loop) - I gave up in the end, but found this : Windows 7 as a WAP. It does the same thing, only it's not an ad-hoc network - you can also share wifi internet through the same wifi adapter...it works great for me!
baladev said:
if you had this happening, it meant the wpa_supplicant you'd tried wasn't compatible with your device. Always backup wpa_supplicant before replacing in in case the new one doesn't work.
Click to expand...
Click to collapse
I did backup. But, even after putting the original wpa_supplicant back in, wi-fi was still broken. So, the only way for me to fix it was to reinstall the firmware.
Try this wpa_supplicant, it works with my 5.0.
Click to expand...
Click to collapse
Thanks. I've been playing with that wpa_supplicant for a while now. However, it did not solve the problem.
It detects the ad-hoc network that I set up on my laptop, but I'm having a hard time trying to connect to it. So far, I've only been able to connect twice. What I need to do in order to connect successfully is to keep enabling and disabling wi-fi. Each time I enable it, it will automatically attempt to connect to the ad-hoc network (because it remembers the info). Most of the time, it will say "Connected", but it actually isn't connected. It only succeeds like once every 50 attempts. And even if it succeeds, it will disconnect automatically after like 10 seconds. At least it gave me enough time to test the internet connectivity, which worked fine during those few seconds. Changing the encryption type from WEP to WPA only made things worse.
Mmmm-) said:
I had the same problem with Ad-hoc networks using windows7 (ie obtaining ip address loop) - I gave up in the end, but found this : Windows 7 as a WAP. It does the same thing, only it's not an ad-hoc network - you can also share wifi internet through the same wifi adapter...it works great for me!
Click to expand...
Click to collapse
That seems like a great idea. However, my laptop's wireless adapter (Intel PRO/Wireless 3945ABG) does not support that functionality. An adapter with Windows 7 certified drivers is required. I also tried to use Connectify, but it also does not support this adapter.
Wiz7 said:
..
It detects the ad-hoc network that I set up on my laptop, but I'm having a hard time trying to connect to it. So far, I've only been able to connect twice. What I need to do in order to connect successfully is to keep enabling and disabling wi-fi. Each time I enable it, it will automatically attempt to connect to the ad-hoc network (because it remembers the info). Most of the time, it will say "Connected", but it actually isn't connected. It only succeeds like once every 50 attempts. And even if it succeeds, it will disconnect automatically after like 10 seconds. At least it gave me enough time to test the internet connectivity, which worked fine during those few seconds. Changing the encryption type from WEP to WPA only made things worse.
..
Click to expand...
Click to collapse
that's very strange. This wpa_supplicant works on my GP 5.0 very well. It detects my WEP ad-hoc network and connects to it just fine and keeps connection until i disconnect. Sometimes it won't connect right away, in which case i just turn wi-fi off and then on again and then it finds the connection, connects and then everything's fine.
Wiz7 said:
That seems like a great idea. However, my laptop's wireless adapter (Intel PRO/Wireless 3945ABG) does not support that functionality. An adapter with Windows 7 certified drivers is required. I also tried to use Connectify, but it also does not support this adapter.
Click to expand...
Click to collapse
Agghh that's a shame.... you could try buying a wifi dongle.. they're not all that expensive...
After playing a bit with the network adapter settings on the laptop, I am now able to connect successfully to the ad-hoc network as soon as I enable wi-fi. What I did was changing the property "Ad Hoc Channel 802.11b/g" to 1 (it was 11 before). Setting this property to anything other than 1 makes it not be able to connect.
There is still the issue of automatically disconnecting after a while (which can vary from seconds to minutes), but it doesn't happen very often, and I'm usually able to stay connected for a long time. Playing with the network adapter properties didn't seem to help in this regard. Anyway, I guess that the problem is solved.
It should be noted that I've never had to change the network adapter settings for any anything else before. I've always been able to connect to other computers via an ad-hoc network. I also used to be able to connect with my SGP 5.0 when I had a different ROM installed. The looping problem that I had before (see my early posts in this thread) could probably be solved also by changing that property in the adapter.
Wiz7 said:
After playing a bit with the network adapter settings on the laptop, I am now able to connect successfully to the ad-hoc network as soon as I enable wi-fi. What I did was changing the property "Ad Hoc Channel 802.11b/g" to 1 (it was 11 before). Setting this property to anything other than 1 makes it not be able to connect.
Click to expand...
Click to collapse
How did you get to that property? I can't find anything similar on mine...
Control Panel -> Network and Sharing Center -> Change adapter settings -> Right-click on the wireless adapter -> Properties -> Configure... -> Advanced.
The properties for the network adapter are listed there, and you should be able to change them.
Wiz7 said:
Control Panel -> Network and Sharing Center -> Change adapter settings -> Right-click on the wireless adapter -> Properties -> Configure... -> Advanced.
The properties for the network adapter are listed there, and you should be able to change them.
Click to expand...
Click to collapse
Hmmm yes, I looked there but unfortunately there is no option to change or configure the channel at all!
I suppose it's driver dependent.
Well, the title says pretty much all .. I earlier didn't have this problem.. Then since last night, I came back home and connected my Galaxy Ace to my home wifi, but this time, it wasn't transferring any data.. It would be connected, full signal, but no internet connection.. My browser, gmail, YouTube, PlayStore, nothing would load.. It'd keep saying Connection Error. Retry.
My wifi works properly on the computer and other devices, and my phone used to work perfectly too! Why's it suddenly giving this problem?!
Any solutions!?
SOLVED!
Okay so I figured it out on my own!!
I went to Wifi Settings>> Advanced>> and "Use Static IP"
I then provided my phone with an IP address, gave the DNS servers as mentioned by my Router, and gateway, is ofcourse, the IP adress of the router. NETMASK is Subnet mask ..
Once I filled in them correctly, and as per my router settings, my mobile is now transferring data and I can now access the internet!
Just thought I'd post a reply incase anyone else was facing this problem
No data through laptop hotspot.
I have a similar problem, but with using my laptop as an access point. My Samsung Galaxy Ace had no problem connecting to either my or my wife's laptop access points initially till about a week ago. I use an HP while my wife uses a DELL. We both run Windows 7. But, here's when things started to get strange.
1. The Ace even though connected through my laptop's AP Wi-fi cannot send or receive data after the first few seconds.
2. My wife's Dell XCD35 (ZTE Blade) has no problems.
3. The Ace has no problem connecting to an Android AP or my wife's laptop AP.
I reflash and unrooted my phone and basically brought it back to factory settings but no luck.
Tried using other services for using my laptop as an accesspoint - mhotspot, virtual router and connectify - still no luck.
tried static ip - no luck.
reinstalled the MS Virtual Wi-fi Miniport Adaptop driver - no luck.
Somehow, there is a security setting on the laptop that's preventing my phone from connecting to the internet. I think I maybe connected to the network, but access to the internet is restricted.
There are no other features like MAC address binding or anything like for laptop APs.
It's getting really frustrating now.
Any help would be appreciated.
lobotomy said:
I have a similar problem, but with using my laptop as an access point. My Samsung Galaxy Ace had no problem connecting to either my or my wife's laptop access points initially till about a week ago. I use an HP while my wife uses a DELL. We both run Windows 7. But, here's when things started to get strange.
1. The Ace even though connected through my laptop's AP Wi-fi cannot send or receive data after the first few seconds.
2. My wife's Dell XCD35 (ZTE Blade) has no problems.
3. The Ace has no problem connecting to an Android AP or my wife's laptop AP.
I reflash and unrooted my phone and basically brought it back to factory settings but no luck.
Tried using other services for using my laptop as an accesspoint - mhotspot, virtual router and connectify - still no luck.
tried static ip - no luck.
reinstalled the MS Virtual Wi-fi Miniport Adaptop driver - no luck.
Somehow, there is a security setting on the laptop that's preventing my phone from connecting to the internet. I think I maybe connected to the network, but access to the internet is restricted.
There are no other features like MAC address binding or anything like for laptop APs.
It's getting really frustrating now.
Any help would be appreciated.
Click to expand...
Click to collapse
Set your Internet to "Allow other computers to share this Internet connection". Other ideas would be to check/disable your firewall
Wifi connected but not working
My Galaxy ace plus connects fine to wifi network but cannot browse internet or play store. I am using a free public wifi so i dont know about the static ip address. And this problem was from the starting whn i just bought it. So is there any other solution for this problem or not?
I tried everything... I restarted the modem- no luck. I filled in the blank from the advance wifi setting- no luck
Hello everybody.
Since last saturday i'm testing a Galaxy S3.
I want to test if everything works properly before buying it.
I have some problems deling with the WIFI stuff.
I gave him a static IP (192.168.1.15), configured the gateway as the ip of my router (192.168.1.1),
the network class is 255.255.255.0 (network prefix = 24), the DNS points to the IP of the Router (192.168.1.1)
It connects without problems. form the S3 i can ping any device in my network and from other devices i can ping the S3.
I can connect to the configuration site of the router and from the page of connected devices i can see that the S3 is connected
with the correct ip and also the MAC adress is correct.
And for now everything is fine.
Problems raise up when i try to surf internet. The answer is always "Page not found"
If i open the browser and try to navigate to google] the answer is "Page not found". Same for any other site i try to connect with.
I cannot ping external adresses from the S3. Only the ones inside my LAN.
On the same LAN there are 3 laptops, 1 IPhone, 1 TV, NAS NETGEAR , home automation screen, all connected in WIFI.
All of them configured in the same way. (static ip, gateway=ip router, dns = ip router, network class 255.255.255.0),
And they all access internet without any problem.
The network is protected with WPA2/PSKey, encryption AES.
I tried to configure channel with WPA, WEP, without protection, but no changes.
The S3 connects to router but does not connect to internet,
I also tried to make it point to a public DNS 8.8.8.8. No WAY!
Works for other devices.
I tried to reset S3 to factory parameters, same thing i did for the router.
I reconfigured everything from scratch but no result.
I do not have any filtering based on IP or MAC adress on my Router.
I tried with DHCP, with reservation of IP adresses or without reservation. No change.
Other devices can access internet. S3 does not.
I have to say i'm quite desperate.
If you guys have some good ideas to solve or diagnostic the problem i would be grateful.
Cheers,
Fabio
I get that around my office as I walk around, I find that when I change AP in range my internet connection drops. I have to constantly disable/re-enable WiFi.
Even around my house, I have the handset to WiFi always on, yet when I wake up in the morning the internet connection is not working yet there is an IP. I couldn't be bothered to telnet to port 80 etc., but I hear that the Jellybean update will resolve this issue.
Same problem
nickzap said:
Hello everybody.
Since last saturday i'm testing a Galaxy S3.
I want to test if everything works properly before buying it.
I have some problems deling with the WIFI stuff.
I gave him a static IP (192.168.1.15), configured the gateway as the ip of my router (192.168.1.1),
the network class is 255.255.255.0 (network prefix = 24), the DNS points to the IP of the Router (192.168.1.1)
It connects without problems. form the S3 i can ping any device in my network and from other devices i can ping the S3.
I can connect to the configuration site of the router and from the page of connected devices i can see that the S3 is connected
with the correct ip and also the MAC adress is correct.
And for now everything is fine.
Problems raise up when i try to surf internet. The answer is always "Page not found"
If i open the browser and try to navigate to google] the answer is "Page not found". Same for any other site i try to connect with.
I cannot ping external adresses from the S3. Only the ones inside my LAN.
On the same LAN there are 3 laptops, 1 IPhone, 1 TV, NAS NETGEAR , home automation screen, all connected in WIFI.
All of them configured in the same way. (static ip, gateway=ip router, dns = ip router, network class 255.255.255.0),
And they all access internet without any problem.
The network is protected with WPA2/PSKey, encryption AES.
I tried to configure channel with WPA, WEP, without protection, but no changes.
The S3 connects to router but does not connect to internet,
I also tried to make it point to a public DNS 8.8.8.8. No WAY!
Works for other devices.
I tried to reset S3 to factory parameters, same thing i did for the router.
I reconfigured everything from scratch but no result.
I do not have any filtering based on IP or MAC adress on my Router.
I tried with DHCP, with reservation of IP adresses or without reservation. No change.
Other devices can access internet. S3 does not.
I have to say i'm quite desperate.
If you guys have some good ideas to solve or diagnostic the problem i would be grateful.
Cheers,
Fabio
Click to expand...
Click to collapse
I'm having the exact same problem, I'd really like to know if you were able to solve the problem.
Phoenix_Dean said:
I'm having the exact same problem, I'd really like to know if you were able to solve the problem.
Click to expand...
Click to collapse
Me too... Is anybody has solution for this issue?
Oh poor fellows ....try to add DNS manually according to your ISP...not add public DNS
Try forgetting the network and connecting again and make sure all the other devices are using different ip address
Sent from my GT-I9300 using xda app-developers app
I am in university halls of residence. I have setup a Wi-Fi hotspot in my room using a generic router by connecting from the ethernet out port in the wall to a ethernet LAN port and disabling DHCP on the router.
This works perfectly for my Windows 7 laptop. It connects to the router and then to the uni internet without issues. However, although my Samsung Galaxy S3 (International i9300) can detect the network, if I just try to connect to the network as I would any other it gets stuck when obtaining an IP address. After messing around with it for a bit i found that I could get the phone to connect by going into the advanced settings and choosing "static" instead of "DCHP". I don't know what I was really meant to enter for IP Address, gateway, subnet, DNS 1 and DNS 2.
The router has the IP of 192.168.1.1 when i connect it directly to my laptop via ethernet so I tried that as the gateway, I set the IP address to something like 192.168.1.14 (So that it was similar but different), I set the subnet to 255.255.255.0 and the DNS servers I used google's (8.8.8.8 and 8.8.4.4). This got me connected to the router but there doesn't appear to be any internet connection.
I therefore thought that I had entered wrong information for the network (I was only guessing after all). Therefore I went into ipconfig in Windows and copied the default gateway and DNS servers and used a similar IP address (Last number different). I had the same issue.
Does anyone have any suggestions?
I only want Wi-Fi in my room for mobile.