I've teste CPU Control lite to change the CPU Min frequency and Governor in my Galaxy Player 5, but the app fails to tell what's the previous setting.
Can anybody tell me the default Min Frequency and governor?
The default Governor is called Lazy and im not too sure about the min frequency but I think it may be 600mhz
When I use setcpu, it reports that the cpu can go all the way to 100mhz under lazy scaling.
Related
i have setup one profile for setcpu to be like this:
"Screen off"
Max: 245760
min: 245760
(this is the lowest value selectable)
Scaling: Powersave
Priority: 100
I assume the priority being the highest the better it is selected... correct?
also on the main screen i have it set to "Conservative" and a max value of 768 and minimum of 245.
I've noticed this has made some improvements when the phone is on standby.
anybody else got any tips / tricks?
The priority is the priority of the profile, not CPU. (e.g. the screen is off, but is also charging, which one should come first)
Bear in mind that...
The lower speed - the longer time it takes to perform a task, and vice versa.
If you are running a lot of CPU-eater software, lower the clock won't help. It will just make your device choppy. And it could take more time for 'you' to play with it while the screen is on. (And the screen is the greatest juice-drinker)
So, during screen-on, the default one should be the best (2xx-9xx, on demand)
While stand-by : just keep it low. but make sure that most background software run correctly.
cylent said:
i have setup one profile for setcpu to be like this:
"Screen off"
Max: 245760
min: 245760
(this is the lowest value selectable)
Scaling: Powersave
Priority: 100
I assume the priority being the highest the better it is selected... correct?
also on the main screen i have it set to "Conservative" and a max value of 768 and minimum of 245.
I've noticed this has made some improvements when the phone is on standby.
anybody else got any tips / tricks?
Click to expand...
Click to collapse
Use set Cpu only if u r still on 1.6 , Because Sony's 2.1 already optimises your system to run at 240mhz when not in use. So basically setcpu aint doing anything at all. untill you want it to run at higher speed , which i doubt. There is absolutely no use of setcpu anymore. Rest is upto you
I use these profiles:
Screen off - 576 max, 245 min, ondemand - Priority 70
Charging/Full - 998 max, 576 min, performance - Priority 50
Battery < 101% - 998 max, 576 min, ondemand - Priority 30
Great battery life, and great performance when the screen is on.
I m using this profile setup for SetCPU...........thanxx KEVINKILEER
Install SetCPU from the market or from the official thread :
http://forum.xda-developers.com/showthread.php?t=505419
(use Root browser and go to sdcard to install the apk)
Run SetCPU and click Autodetect Speeds. Allow Superuser.
Tick Set on boot.
Go to Profiles, tick enable / notifications.
Add profiles:
Profile 1: In call: Min 122880 , Max 787200 , Scaling conservative , Priority 100
Profile 2: Screen off: Min 122880 , Max 122880 , Scaling powersave , priority 90
Profile 3: Charging: Min 245760 , Max 825600 (set higher if you want, depends on the phone, I set it to 902400, your phone might reboot) , Scaling ondemand , Priority 80
Profile 4: Battery: 50%: Min 122880 , Max 787200 , Scaling conservative , priority 70 (remove this profile if you care more about performance)
Profile 5: Battery: 101%: Min 122880 Max 806400 (set higher for more performance and less battery life) , Scaling ondemand (set to conservative if you want to save more battery) , priority 60
(Set min CPU speed to 245mhz to fix wake up lag, uses more battery however.)
Add different/more profiles if you want, these are the ones I use.
Its great app to control the speed and battery as well, been using this too and it helps a lot.
anyone have insights on setcpu profiles for our notes? is it even necessary to set up profiles if I leave the main default on 192/1836 smartassv2 governor?
Hi guys, i have a problem with CM 10 kernel. I don't need overlock, so i set the minimum frequency on 200 mhz and maximum on 1000. But sometimes (for example when i turn on) i can see it runs on 1150 and when i change performance setting, overlock is disable, but i see after 2, 3 hours, i don't know, that the maximum frequency is on 1150. So i have to set again and disable overlock. I use on demand governor and cfq scheduler. Thanks and sorry for my english!
CPU scaling app. maybe it would help with battery life if we had the option to scale down the cpu