Hello.
I bought a motorola Atrix few weeks ago. Guy who sold me a phone unlocked a bootloader, Rooted a phone ...he done all stuff including putting in a Dark Side PreFinal CROM.
I updated phone to Nottachtrix4G build from AT&T 4.5.141 release.
I had version 2.2.Everything was worked fine but phone seems to be hanging and i noticed version 2.5 with that bad installer and i couldn`t install ROM because of it.
Then i wanted to put in a Neutrino ROM V2.5. I putted a ROM file on my 32GB SD card and running through Android Reovery i geted working Neutrino but it woulds get any addons properly installed so i decided to put same ROM on Internal Memory and then Bang.
Its seems to that whole process in Android Recovery went OK but when now i getting a restart loops when i switching on a phone. It gets past the Red M and reboot.
When im trying to go into Android Recovery then i got black screen. I can`t charge a phone due to Loop Restarts. Any help ?.
I heard that i can use SBF File to recover a phone but im afraid to get it HARD Bricked if its rooted and unlocked.
Related
hello i recently purchased this tablet ahappydeal.com/product-160586.html
but i made the mistake of installing chainfire 3d clicked install driver and now
it wont boot it just goes to a white scree witth oem powered by and does not go any further
i know you can flash the stock rom back onto it but i have googled forumed youtubed
everything i juust cannot find one so i'm hoping you guys can help me out i am desperate at the moment
also if you know of any custom roms or where i might get the stock rom perhaps
Good Evening/Hello/Hi,
I own a Samsung Galaxy S III GT-i9300 International Version. I recently started experimenting with roms and cwm and i think i ended up in a dark tunnel. I rooted my phone and installed clockwork (cf auto root) and then tried installing KitKat Rom 4.4 but kept failing each time i entered recovery and tries to flash it. by reading other posts it was suggested to use a higher version of cwm as i was using a 5.0.4.6 version. after trying a later version the rom flashed and also the gaps without any problem. however after booting i realized i had no service, but the phone seemed ok. i decided to flash modem_XXDME4 and Modem DDEMG2 in recovery after reading some posts to get signal back. that's when the trouble started, when the phone rebooted i could not get pass the setup screen to select language, touch is not responding up to this time, i reflashed stock rom, it booted and still no touch , cant get pass the start screen of the language selection. my phone never fell and the creen has no sign of falling. any help would be greatly appreciate.....:crying::crying:
Thank You
Hi, I hope this is posted in the right place.
My Alcatel One Touch 983 is stuck on the android logo on boot.
I have tried removing the battery, SD card and the sim card, this doesn't help.
Also I have charged the phone and this also doesn't help.
I rooted the phone about 6 months ago and it has been fine until now. I haven't even put any custom roms on it.
The phone still runs the stock rom.
I am not sure what would have caused this, the phone was working fine and it must of turned off because of low battery but now it wont boot.
I can't even get it into recovery mode.
The phones os is Android Gingerbread 2.3.7
Is there a way to fix this?
Also, if there is no way to fix this, would a Moto G be a good phone to buy?
Hello,
If you're able to get in download mode you can restore the Firmware of your phone.
The Moto G is indeed a good phone to buy.
It's the best phone you can get for that price and it has quite good specs
hi guys
really could do with some help
i had flashed my u8850 when i first got my phone and played around with the custom roms which were not fully usable at the time. As my wife wanted the phone I flashed it to stock rom .. proper stock without root or CWM... with SUT l3 tool
now she gave it back to me as she upgraded, and i went to do a factory reset to clear out the contacts etc.. and start afresh.
it went and got stuck at the huawei symbol and hasn't gone off since.
since researching this, i found out that its a boot loop and anyone who has flashed a custom rom can never do a factory reset from the settings menu, but must do it in CWM instead.
so, Im stuck in a boot loop, with a original rom with no CWM and although the computer recognizes the phone as a huawei and loads the ADB drivers etc... Ive got no way to flash a rom with CWM to get me to cyanogen at all.. SUT doesn't recognize the phone at all..
so ive got the roms i need and even tried with android AIO flasher ...
clearly i need some help ...
can you assist?.. thanks..
The same problem
I got the same problem... I "played" with the ROM Toolbox app (changed boot animation, changed status bar icons, changed the SYSTEM UI), and now I got the same problem... Can anyone help us plz.?
Earlier today, I downgraded the firmware from my straighttalk galaxy s3 from stock H2 to H1 and then proceeded to root it, which went fine. After this, I installed CWM recovery and cyanogenmod, once I booted into cyanogenmod, I ran into a bug/glitch which didn't allow my rom to use my mobile data, so after that, I installed android revolution hd. This is where I ran into my problem, I went into CWM and factory reset my phone and wiped all caches, after this I proceeded to install android revolution HD, only to find out that it only shows a black screen, I also cannot use adb, but my computer still recognizes my phone as connected.
PS:
If I leave the battery out and plug in the USB, I get a brief solid red light
The phone WILL NOT go into recovery or download
No boot screen or error
Any and all help you guys can offer is well appreciated as I was not expecting this to happen
Hello imjimbob,
I think your LCD is broken. :crying:
Can you tell me a bit more please, and is there any way to fix it?
How would my phone screen break from flashing a ROM?