Related
was going from gingerblur 2.5 on 1.56 then sbf to 1.83 and now it just says that after flashing.
tried to sbf 1.23 and 56 and same thing
am i doing something wrong?
in the rsdlite it sees the phone but says n/a for everything
Please HELP
Updated: I tried again fresh start on different computer and it worked!
must have been error in download, unzip, or there is something conflicting on my pc
hi i have same problem , went i flash OLYFR_U4_1.8.3_SIGNED_OLPSATTSPE_P013_HWolympus_1g_Service1FF.sbf ,
always after finish and rebooting then failed to boot 4 error raise,
i have use other computer to flash and the result is same failed to boot 4
i have install
- RSD Lite and 5.0
- Handset_USB_Driver_32_v4.9.0
plz can anyone help me ?
Sbf 4.1.26 or 4.1.57, then OTA to 4.1.83, root, sideload enable, flash CWM, flash GingerBlur.
bullghost said:
hi i have same problem , went i flash OLYFR_U4_1.8.3_SIGNED_OLPSATTSPE_P013_HWolympus_1g_Service1FF.sbf ,
always after finish and rebooting then failed to boot 4 error raise,
i have use other computer to flash and the result is same failed to boot 4
i have install
- RSD Lite and 5.0
- Handset_USB_Driver_32_v4.9.0
plz can anyone help me ?
Click to expand...
Click to collapse
i have the same problem
aaurnab said:
i have the same problem
Click to expand...
Click to collapse
please help
CaelanT said:
Sbf 4.1.26 or 4.1.57, then OTA to 4.1.83, root, sideload enable, flash CWM, flash GingerBlur.
Click to expand...
Click to collapse
thanks bro, i thinks that's the best way to update till 4.1.83,
here a little experience i have done
first time i try flash sbf 4.1.83 failed with that error booting,
and pull battery and back again to turn off the phone, and i flash the 1.26
then success with sim card inside,
iam not happy with failing on flash 4.1.83, then i thought the 4.1.83 sbf file is corrupt then i redownload again , after finish download,
i do the second time flashing with new 4.1.83 sbf
this second time is so frustrated, couz it fail again with same error.
until i have success full recover my atrix i do over 10 time flashing
and changing between computer and my notebook
and changing from windows 7 and windows XP
flashing random sbf from 1.83 and 1.26
the lasting i lost my hope , then suddenly the flash was success, WTF ,
lasting i remember is i pull the battery and pull out the sim card , then put back the battery, and do the flash,
the last time i flash 1.26 sbf
i thing
there is something no right with driver or RSD Lite not sync or missing something
until now iam still don't know how to solve it ,
pls anyone can find out what the problem and how to solve it
After about 4-5 hours and 7-8 tries using sfb method to upgrade to 1.83, I finally have a working phone again.
As to how I got stuck on the:
boot fail 4
starting RSD
and in RSD Lite, the phone's device name showing up as "SE Flash Olympus"
I decided to do a few things.
1. Go download the newest USB drivers. the 2.00.52 is what you should be on. If you can't find them, go to Motorola website and get MotoHelper 5.0 or whatever..install and then update your drivers. Restart your pc and keep trying to update your drivers until you get to USB 2.00.52 drivers.
2. USE THE ORIGINAL DATA CABLE THAT CAME WITH THE PHONE.
3. Make sure the connections are not loose at all (could've been why mine was messing up)
4. If you already have motohelper installed...go to the 'driverinstaller.exe' change operation mode to clean and reinstall, make sure the phone is unplugged. and click on start. (note, this part will be anywhere from 2 - 5 minutes depending on speed of your computer)
5. Restart RSD Lite, make sure you're using the latest one, and 'Run as administrator'.
**Go to config>Flash/Flex options... > only "check" Restart after Flexing..**
6. Now, I learned this the hard way...and many forums have it up there... GET YOUR BATTERY TO ABOVE 80% or IT WILL FAIL. (I had to go to a friend's at midnight to charge my battery from his atrix...hahaha)
7. Now turn your phone on again and it'll go to the "failed to boot 4 starting RSD" ...
8. Next, plug it in to your USB cable and click "Show Device" and then click once under the "USB 1 line" to view the device information at the top left. (Everything should be N/A except for your bootloader and you will also read "NS Flash Olympus now, instead of the SE Flash Olympus)
9. Put that '1.83_pudding.sfb' file in the "C:\ " directory to avoid any further complications.
10. Select the "...." browse to the '1.83_pudding.sfb' file and click start. It should work.... Now if it doesn't work... try and try again...
What I did was switched back and forth from 1.23 to 1.83... when I got mine to work, the device was registering as "SE Flash Olympus".
And for the longest time under bootloader, it would register as N/A...I finally decided to switch cables and it worked... once again, make sure to follow these:
* Full battery/80% above
* Stock Atrix USB cable
* 2.00.52 USB drivers
* RSD Lite 5.3.1
EDIT: GOOD LUCK! PM me if you need more assistance as those forward to XDA app
vash8806 said:
After about 4-5 hours and 7-8 tries using sfb method to upgrade to 1.83, I finally have a working phone again.
As to how I got stuck on the:
boot fail 4
starting RSD
and in RSD Lite, the phone's device name showing up as "SE Flash Olympus"
I decided to do a few things.
1. Go download the newest USB drivers. the 2.00.52 is what you should be on. If you can't find them, go to Motorola website and get MotoHelper 5.0 or whatever..install and then update your drivers. Restart your pc and keep trying to update your drivers until you get to USB 2.00.52 drivers.
2. USE THE ORIGINAL DATA CABLE THAT CAME WITH THE PHONE.
3. Make sure the connections are not loose at all (could've been why mine was messing up)
4. If you already have motohelper installed...go to the 'driverinstaller.exe' change operation mode to clean and reinstall, make sure the phone is unplugged. and click on start. (note, this part will be anywhere from 2 - 5 minutes depending on speed of your computer)
5. Restart RSD Lite, make sure you're using the latest one, and 'Run as administrator'.
**Go to config>Flash/Flex options... > only "check" Restart after Flexing..**
6. Now, I learned this the hard way...and many forums have it up there... GET YOUR BATTERY TO ABOVE 80% or IT WILL FAIL. (I had to go to a friend's at midnight to charge my battery from his atrix...hahaha)
7. Now turn your phone on again and it'll go to the "failed to boot 4 starting RSD" ...
8. Next, plug it in to your USB cable and click "Show Device" and then click once under the "USB 1 line" to view the device information at the top left. (Everything should be N/A except for your bootloader and you will also read "NS Flash Olympus now, instead of the SE Flash Olympus)
9. Put that '1.83_pudding.sfb' file in the "C:\ " directory to avoid any further complications.
10. Select the "...." browse to the '1.83_pudding.sfb' file and click start. It should work.... Now if it doesn't work... try and try again...
What I did was switched back and forth from 1.23 to 1.83... when I got mine to work, the device was registering as "SE Flash Olympus".
And for the longest time under bootloader, it would register as N/A...I finally decided to switch cables and it worked... once again, make sure to follow these:
* Full battery/80% above
* Stock Atrix USB cable
* 2.00.52 USB drivers
* RSD Lite 5.3.1
EDIT: GOOD LUCK! PM me if you need more assistance as those forward to XDA app
Click to expand...
Click to collapse
People 51_OLL iron-4.5.2A-lite 5.6 rsd 49_SIGNED_STABLE45LAOLYMPGBPERAR_P011_A026_M001_HWpd_Service1FF with ... and my error:
"Failde to boot 4"
rsd starting mode
I am reading is the battery problem that has to be for 80 %+...
If I turn on the power but the volume key + I fastboot protocol enters
If it lights only the error:
"Failde to boot 4" starting mode rsd
I can do twice the iron sbf with 2.3.6 official stock continues to give me the same error.
Lei may be because the battery is not 100% so fails.
How do I charge if the wall charger no load and light me alone with the legend:
"Failde to boot 4" rsd starting mode.
It can be for this, because this is not a 100% Bateias??
Another query may be that by command fastboot mode can be fixed??
So playing around with a modified Atrix rom... I am now locked. Trying to get the phone back up and running using the SBF and RSDLite but having problems getting the software to recognize the phone.
As the phone sits, it now reads at the initial boot.
Code:
Failed to boot 2
Starting RSD mode
I've tried to take it into recovery mode (created a nandroid backup already to the external microSD) without any luck.
I installed the atrix clockwork recovery (I thought I read somewhere that the atrix CWR worked on the X2) FAILED
Mine now reads same as the OP. Im having to redownload the SBF as Im on Vacation away from my PC that has everything on it.. SO, Ill post if I have additional issues
Hi, I am sorry you are having so much trouble. Hopefully I can provide the steps and help to guide you into successfully recovering your phone from this boot error.
From what I understand you're receiving the following error: "failed to boot 2. starting rsd mode"
I have encountered this error a few times while developing MinimalX. Fortunately, you should be able to recover this using the proper method.
First, turn off your device and plug it in. You will need a certain amount of battery life to perform an SBF without error, so, take advantage of these download times to increase your charge using a wall charger.
Next, you will need to download and install DX2 Drivers and RSD Lite.
You will also need the SBF file, which can be downloaded here:
SBF File
(note: be sure to unzip the file)
Once everything has downloaded and installed successfully, unplug your device from the USB. Plug your USB into your computer only. Then, run RSD Lite with administrator permissions. Browse to and select your SBF file (VRZ_MB870_DTN-14.8_1FF_01.sbf). Then turn on your device, and when you get the "starting RSD mode" prompt, plug in the usb cord from computer to phone. RSD Lite should then recognize your phone, and from there, simply, press start and leave the device and your computer alone until completion (not necessary, but extra precaution). Once this finishes and the phone boots, I highly recommend also doing a factory reset in settings > privacy.
I hope you the best and that this is able to restore function toyour phone. If you need any additional help, feel free to PM me or post in this thread.
Happy DROID-ing!
Sent from my DROID X2 using Tapatalk
Ran into this problem yesterday. Had issues with RSD Lite. Make sure you have the latest version or it will fail. Has to be version 5.3.1 and NOT 5.0 or whatever.
then it should work without a hitch.
Just a reminder, you will have your apps and stuff still installed including SuperUser. You will have to run Gingerbreak again to reroot to add the files back into the proper location, SuperUser doesn't work even with the .apk installed by itself. Just fyi.
Follow instructions here and download files from links provided...
http://forum.xda-developers.com/showthread.php?t=1175300
Yeah Don't Try And Flash The Atrix In Rom Manager, It Will Give You That Error Too.
Apparently there's a link floating around pointing to RSDLite 5.0 renamed and hacked to show 5.3.1. While the download says 5.3.1, the install says 5.3.1, it's still only 5.0.
Thanks again to those working to make the X2 a better phone. Perhaps we can get GB up and running on this thing before the OTA is released. Wouldn't that be egg-on-the-face.
Hi
All
My Dell Streak5 Ver 1.6 Locked with O2 Network.
I have some Unlocking Tools For My Dell Unlocking.But its Need Android ver 2.2 or above.
So I try For Update MY Dell Streak.To 2.2.
Detail
1)I update My Dell Streak Direct With O2 Service(Go Setting Software Update)
Download Complete But STUCK ON Installing Update.
2)I Update My Dell with Stock Rom(which download with O2 Network in SD card)
With SD card(update complete But Phone Stuck on Dell logo)
3)I Flash It with Clockmode Recovery An try for Update..
with Zip File..(Error "Can,t Mout SD card ,etc)
4)I Flash It with StreakDroid Recovery and try for update
with Streakdroid.Zip file(Same error"can,t Mount SDcard)(think Rooted problem)
5)I Flash it With High Dell Recovery And try to Match Update.pkg(ver 2.2 froyo)
Flashing 70% or 80% then error(error in update.pkg.dec)
After this the phone is Stuck on O2 Logo.
Now My phone IS not in working position..
so I try for 1.6 recovery with 1.6 update.pkg....but here is also error.(after flash stock
Recovery match 1.6 ..the phone blank after Apply"Software Update with update.pkg")
So How I can Recover my PHONE...WITH any Version....
Need Help Plz.........
Arif Jamil said:
Hi
All
My Dell Streak5 Ver 1.6 Locked with O2 Network.
I have some Unlocking Tools For My Dell Unlocking.But its Need Android ver 2.2 or above.
So I try For Update MY Dell Streak.To 2.2.
Detail
1)I update My Dell Streak Direct With O2 Service(Go Setting Software Update)
Download Complete But STUCK ON Installing Update.
2)I Update My Dell with Stock Rom(which download with O2 Network in SD card)
With SD card(update complete But Phone Stuck on Dell logo)
3)I Flash It with Clockmode Recovery An try for Update..
with Zip File..(Error "Can,t Mout SD card ,etc)
4)I Flash It with StreakDroid Recovery and try for update
with Streakdroid.Zip file(Same error"can,t Mount SDcard)(think Rooted problem)
5)I Flash it With High Dell Recovery And try to Match Update.pkg(ver 2.2 froyo)
Flashing 70% or 80% then error(error in update.pkg.dec)
After this the phone is Stuck on O2 Logo.
Now My phone IS not in working position..
so I try for 1.6 recovery with 1.6 update.pkg....but here is also error.(after flash stock
Recovery match 1.6 ..the phone blank after Apply"Software Update with update.pkg")
So How I can Recover my PHONE...WITH any Version....
Need Help Plz.........
Click to expand...
Click to collapse
You will have to become familiar with using fastboot.
If you are stuck on dell logo, you will have no options but to flash stock recovery and then flash the correct stock rom.
Apart from below method, if you cannot get to fastboot screen, then download QDLTool as that is said to work also.
Here are listed some facts, tools and links to roms and recovery images.
Download Dell Streak drivers, fastboot driver and exe, Dell Streak PC Suite.
Download the recovery img and the corresponding choice of rom image, put the rom image on your sd card and rename it update.pkg.
cc
Place fastboot.exe and recovery.img in the root of your C drive, C:\
Now using fastboot, assuming you have installed fastboot driver and dell streak driver.
Get your device into fastboot mode, hold down power and camera shutter button at the same time.
At the white screen choose fastboot, wait abotu 10 seconds while it tries to detect usb then connect your cable from pc into your phone.
Now open a command prompt in windows.
In command prompt box type:
fastboot -i 0x413c flash recovery recovery.img
Your chosen roms recovery.img should be flashed to the phone. Now reboot the phone using command at prompt: fastboot -i 0x413c reboot
Now hold down volume up and volume down at dell logo, get into recovery mode, and then press the camera shutter button, and your stock rom of choice should be flashed to your phone.
You should now have a working phone, once flashed do a factory reset to make sure all is good.
Questions or Problems Should Not Be Posted in the Development Forum
Please Post in the Correct Forums and Read THIS
Moving to General
(InsertNameHere) said:
You will have to become familiar with using fastboot.
If you are stuck on dell logo, you will have no options but to flash stock recovery and then flash the correct stock rom.
Apart from below method, if you cannot get to fastboot screen, then download QDLTool as that is said to work also.
Here are listed some facts, tools and links to roms and recovery images.
Download Dell Streak drivers, fastboot driver and exe, Dell Streak PC Suite.
Download the recovery img and the corresponding choice of rom image, put the rom image on your sd card and rename it update.pkg.
cc
Place fastboot.exe and recovery.img in the root of your C drive, C:\
Now using fastboot, assuming you have installed fastboot driver and dell streak driver.
Get your device into fastboot mode, hold down power and camera shutter button at the same time.
At the white screen choose fastboot, wait abotu 10 seconds while it tries to detect usb then connect your cable from pc into your phone.
Now open a command prompt in windows.
In command prompt box type:
fastboot -i 0x413c flash recovery recovery.img
Your chosen roms recovery.img should be flashed to the phone. Now reboot the phone using command at prompt: fastboot -i 0x413c reboot
Now hold down volume up and volume down at dell logo, get into recovery mode, and then press the camera shutter button, and your stock rom of choice should be flashed to your phone.
You should now have a working phone, once flashed do a factory reset to make sure all is good.
Click to expand...
Click to collapse
i use allready Fastboot mode for flashing Recovery image.
And Also use QDL.exe
On QDL.exe the procces will Succesfull but phone in only DEll logo Shining.
And After streadmode recovery or clockmode rcovery .try updateing with SDCARD
get this error
"can,t mount sdcard:update.zip
or
signature verification field
and after flash a new stock recovery ..and update with any stock rom get this error"open INSTALL_IMAGE fail"
In Last...
br
Arif Jamil said:
i use allready Fastboot mode for flashing Recovery image.
And Also use QDL.exe
On QDL.exe the procces will Succesfull but phone in only DEll logo Shining.
And After streadmode recovery or clockmode rcovery .try updateing with SDCARD
get this error
"can,t mount sdcard:update.zip
or
signature verification field
and after flash a new stock recovery ..and update with any stock rom get this error"open INSTALL_IMAGE fail"
In Last...
br
Click to expand...
Click to collapse
If you have tried everything and i mean everything, is it possible you have a faulty insternal sd card?
(InsertNameHere) said:
If you have tried everything and i mean everything, is it possible you have a faulty insternal sd card?
Click to expand...
Click to collapse
br
this problem get after using QDL repair Tool.. before this my Dell streek Flash ok with
Official O2 1.6 file.
Arif Jamil said:
br
this problem get after using QDL repair Tool.. before this my Dell streek Flash ok with
Official O2 1.6 file.
Click to expand...
Click to collapse
So what is the score now, what do you want on your phone, or should we say, what can you get installed that works ok.
QDLTool latest should work fine. If you cannot get QDLTool or fastboot recovery.img and flash etc to work, then surely you have a big problem. I have flashed to custom roms and back to stock roms simply using fastboot recovery.img and rom .pkg for stock roms and streakmod to flash .zip packages with custom roms.
But others are better qualified to help to be honest, but the tools i have mentioned are the tools of emergency recovery, if that fails, its something more serious.
I'm pretty much in the same boat as Arif.
Your instructions are great, and they go very well until this part: "Now hold down volume up and volume down at dell logo, get into recovery mode, and then press the camera shutter button, and your stock rom of choice should be flashed to your phone."
I've always been able to get into recovery mode this way where there are options for factory reset, software upgrade, and screen calibration. (Software upgrade gives me "Cannot mount mnt/sdcard/update.pkg - no such file or directory")
Didn't you just have me flash a new recovery? How do I get to it?
Did you flash the recovery using fast boot and then go straight into recovery before the phpne boots up again? If it boots I think it automatically rewrites the recovery to stock if you are currently on a stock rom.
Sent from my Dell Streak using xda premium
It seems like it's successfully flashing recovery using fastboot, the command prompt says "writing/sending recovery .... okay .... finished" and the phone's fastboot screen says "fastboot mode .... download complete".
Then I reboot using the command prompt and as soon as the screen goes from fastboot to black I hold the volume buttons until it gets to recovery. ....but it still looks like stock recovery. and when I hit the camera button to apply the update, I get the "can't mount update.zip" error.
so far I've tried the 407 and 360 roms/recoveries from this page: http://forum.xda-developers.com/wiki/Dell_Streak_5#ROMs - should I just keep trying different roms & recoveries?
I found a post here on xda saying that the sd card might have to be formatted as ext3.
I tried that, and still it's the same error "E:Can't mount /dev/block/mmcblk1p5"
Hey Guys,
I searched for my problem in many places, no go.
No one talking about Streak not going into Fastboot mode. Had to start this new thread.
---------------------------Here's what happened...---------------------------
I was trying to install GingerStreak 2.4.4 from GingerStreak 2.4.3.
DJ Steve's Thread
According to the instructions, I flashed
amss.mbn
and
dsp1.mbn
(got both the files from the first link above)
---------------------------Now the problem is...---------------------------
Then when I tried to reboot into Bootloader (Power+Vol Up+Vol Down) nothing happens apart from the Dell logo being displayed.
I try to boot normally, still stuck at the Dell logo. The phone never even reaches the boot animation.
I try to go boot into fastboot (power+camera key)mode, but the phone never even boots. The screen stays off, so do the LED lights.
---------------------------The problem I found out---------------------------
I figured out that the files downloaded above were incomplete(due to slow speed Chrome showed incomplete files as download complete).
amss downloaded: 111KB. Actual Size: 15.41MB
DSP1 Downloaded: 250KB. Actual Size: 8.94MB
So, I flashed the wrong files.
Now, I guess, the phone is bricked big time.
I need to get into fastboot mode (to flash the correct files) or anyhow get my phone working.
I also need to know if QDL tool will help me sort this out. It is currently downloading(again very slowly). If I get the answer, will post back.
Guys, need help. Please help me out to get this issue sorted out.
me also have same problem
supersophisticated said:
Hey Guys,
I searched for my problem in many places, no go.
No one talking about Streak not going into Fastboot mode. Had to start this new thread.
---------------------------Here's what happened...---------------------------
I was trying to install GingerStreak 2.4.4 from GingerStreak 2.4.3.
DJ Steve's Thread
According to the instructions, I flashed
amss.mbn
and
dsp1.mbn
(got both the files from the first link above)
---------------------------Now the problem is...---------------------------
Then when I tried to reboot into Bootloader (Power+Vol Up+Vol Down) nothing happens apart from the Dell logo being displayed.
I try to boot normally, still stuck at the Dell logo. The phone never even reaches the boot animation.
I try to go boot into fastboot (power+camera key)mode, but the phone never even boots. The screen stays off, so do the LED lights.
---------------------------The problem I found out---------------------------
I figured out that the files downloaded above were incomplete(due to slow speed Chrome showed incomplete files as download complete).
amss downloaded: 111KB. Actual Size: 15.41MB
DSP1 Downloaded: 250KB. Actual Size: 8.94MB
So, I flashed the wrong files.
Now, I guess, the phone is bricked big time.
I need to get into fastboot mode (to flash the correct files) or anyhow get my phone working.
I also need to know if QDL tool will help me sort this out. It is currently downloading(again very slowly). If I get the answer, will post back.
Guys, need help. Please help me out to get this issue sorted out.
Click to expand...
Click to collapse
pls help me out from this problem
Figured out and finally unbricked my Dell Streak
Yessss...... my phone is back!!!
Here's the solution.
Try this...
Go to this page...
RDTK.net
Look for QDL tool and streakflash.zip.
Firstly after the download, you have to get the drivers (guess the problem is only with Win7 64 bit OS) in place.
The same link above has the links on tutorials to install QDL tool drivers for Qualcomm HS-USB Diagnostics 9002.
After this...
1) Run streakflash version from the streakflash.zip(after extraction though).
2) Boot into diagnostic mode (Vol Up + Power button) and connect the USB cable to the computer. 'Qualcomm HS-USB Diagnostics 9002' will show in the port field in streakflash QDL tool.
3) Hit the run button. The process should stop at success.
4) Disconnect USB cable and close streakflash QDL tool.
5) Now run the QDL tool that came in repairtool.zip (after extraction though).
6) Boot the Streak into diagnostic mode (Vol Up + Power button) and connect the USB cable to the computer. 'Qualcomm HS-USB Diagnostics 9002' will show in the port field in QDL tool.
7) Hit the run button. The process should stop at success. If not, dont forget try again and again. Make sure you change USB ports (to which you are connecting ur streak) on ur system too.
This should definitely work. Mine worked like a magic.
As the page linked to says the tutorials and QDLTool versions are mirrored from streakdroid.com. I don't want anyone thinking I am taking credit for others work.
Glad you were able to "unbrick" your phone.
Totally Agree! Sorry I missed out that streakdroid part.
I appreciate your help.
I am thankfull to you, as I was facing same problem with my Streak5.
I am able to use it with DJ_Steve 2.4.4.
Regards.
Mahesh
maheshbhoir said:
I am thankfull to you, as I was facing same problem with my Streak5.
I am able to use it with DJ_Steve 2.4.4.
Regards.
Mahesh
Click to expand...
Click to collapse
Glad Mahesh!
It seems so obvious, but if my post helped, you have the thanks button right there.
.
Help me earn my first one.
supersophisticated said:
Glad Mahesh!
It seems so obvious, but if my post helped, you have the thanks button right there.
.
Help me earn my first one.
Click to expand...
Click to collapse
I just gave it to you, lol
thanks it fixed my streak
supersophisticated said:
Hey Guys,
I searched for my problem in many places, no go.
No one talking about Streak not going into Fastboot mode. Had to start this new thread.
---------------------------Here's what happened...---------------------------
I was trying to install GingerStreak 2.4.4 from GingerStreak 2.4.3.
DJ Steve's Thread
According to the instructions, I flashed
amss.mbn
and
dsp1.mbn
(got both the files from the first link above)
---------------------------Now the problem is...---------------------------
Then when I tried to reboot into Bootloader (Power+Vol Up+Vol Down) nothing happens apart from the Dell logo being displayed.
I try to boot normally, still stuck at the Dell logo. The phone never even reaches the boot animation.
I try to go boot into fastboot (power+camera key)mode, but the phone never even boots. The screen stays off, so do the LED lights.
---------------------------The problem I found out---------------------------
I figured out that the files downloaded above were incomplete(due to slow speed Chrome showed incomplete files as download complete).
amss downloaded: 111KB. Actual Size: 15.41MB
DSP1 Downloaded: 250KB. Actual Size: 8.94MB
So, I flashed the wrong files.
Now, I guess, the phone is bricked big time.
I need to get into fastboot mode (to flash the correct files) or anyhow get my phone working.
I also need to know if QDL tool will help me sort this out. It is currentlyi downloading(again very slowly). If I get the answer, will post back.
Guys, need help. Please help me out to get this issue sorted out.
Click to expand...
Click to collapse
but why you required to flash amss & dsp1 if you are upgrading , is it not only required when you are from 2.2 ?
babamanan said:
but why you required to flash amss & dsp1 if you are upgrading , is it not only required when you are from 2.2 ?
Click to expand...
Click to collapse
Use streakflash to repair it.Then flash the amss and dsp1 file again,because it is necessary for upgrading to 2.3.3.
babamanan said:
but why you required to flash amss & dsp1 if you are upgrading , is it not only required when you are from 2.2 ?
Click to expand...
Click to collapse
Exactly!
I wasn't supposed to flash those files. But since I was fed-up of many issues, I planned that I would go for a clean one starting from scratch.
The best way to install the amss.mbn and dsp1.mbn files is to flash the stock ROM that your custom ROM is based on.
supersophisticated said:
Yessss...... my phone is back!!!
Here's the solution.
Try this...
Firstly after the download, you have to get the drivers (guess the problem is only with Win7 64 bit OS) in place.
The same link above has the links on tutorials to install QDL tool drivers for Qualcomm HS-USB Diagnostics 9002.
After this...
1) Run streakflash version from the streakflash.zip(after extraction though).
2) Boot into diagnostic mode (Vol Up + Power button) and connect the USB cable to the computer. 'Qualcomm HS-USB Diagnostics 9002' will show in the port field in streakflash QDL tool.
3) Hit the run button. The process should stop at success.
4) Disconnect USB cable and close streakflash QDL tool.
5) Now run the QDL tool that came in repairtool.zip (after extraction though).
6) Boot the Streak into diagnostic mode (Vol Up + Power button) and connect the USB cable to the computer. 'Qualcomm HS-USB Diagnostics 9002' will show in the port field in QDL tool.
7) Hit the run button. The process should stop at success. If not, dont forget try again and again. Make sure you change USB ports (to which you are connecting ur streak) on ur system too.
This should definitely work. Mine worked like a magic.
Click to expand...
Click to collapse
Bro you are great. I have no words to say my thanks to you. By your way I fixed my mini5. thanks bro
1. Started RSD Light 5.3.1
2. Downloaded the 2.3.4 file linked here:
http://forum.xda-developers.com/showthread.php?t=1138204
3. Started the flash process.
Failed-- Error Switching phone to BP Pass through mode (0x70BE); phone connected
On the Atrix it says Failed to boot, no os detected, and asked me to choose one of the available modes, of which there are 14 in total.
At the bottom it says "starting fastboot protocol support".
What did I do wrong, and what should I do now?
The SD card is plugged into it. Should I battery pull, remove teh SD card, and try flashing the SBF again?
Thanks.
edit: btw I did unrar to get the sbf first and placed it in c:\.
OK I battery pulled, removed sd card, now only have fastboot protocol support, can't seem to re-do the RSD steps...
Oh, looks like this only happens on the first time you flash. OEM unlocked and it's booting up.