Help Me Please. - Vibrant Q&A, Help & Troubleshooting

Uh hi.
I'm a herp.
So I may have accidently tried to root and flash my friend's Samsung Vibrant. It was going smoohtly but now, I'm all sorts of messed up.
The problem: I may have used the wrong kernel (zImage) when using heimdall-frontend (which I downloaded from xda). This is causing the phone to power on; it shows the Samsung Galaxy S 4g load screen, then Overstock, then the T-Mo logo sign (with the music), and then a longer Galaxy S load screen. After the load screen, the screen goes completely black, but all the touch buttons light up. Once like this, I can turn it off, and make it go back into recovery mode and also download mode.
Please help. I've been trying to solve this with my friend for about.. 4 hours.
P.S. I've looked up all the guides for using ODIN to get back to JFS, none works due to the reason that when I put it back into download mode, the computer does not recognize it. But it does at the same time. (it shows the "safetly remove hardware" and says that is an "USB mass storage device" ((but does not appear in "My Computer" when in the unresponsive screen-- but when in the download screen, it shows the same thing, only labeled "SAMSUNG USB Composite Device", which also cannot be accessed through "My Computer")
P.P.S. I'm sure it is a Samsung Galaxy S Vibrant, exclusive from T-Mobile. My computer is Windows Vista 32-bit, and I have as many Samsung drivers as humanly possible when it comes to the Vibrant.
Can anyone help a poor fool?

Try this, get in to download mode, open Odin, then disconnect the usb cable, then reconnect the usb cable and Odin should recognize it then. Good luck!
Using XDA premium, you should be too!

johnny12times said:
Try this, get in to download mode, open Odin, then disconnect the usb cable, then reconnect the usb cable and Odin should recognize it then. Good luck!
Using XDA premium, you should be too!
Click to expand...
Click to collapse
Sorry. That did not work. It just doesn't recognize it in ODIN when in download mode. My computer doesn't even see it. But it does say "Safely Remove Hardware" -- "SAMSUNG USB Composite Device"

Sounds really odd. Do you have any roms you can try reflashing from recovery?
Using XDA premium, you should be too!

depaer said:
Uh hi.
I'm a herp.
So I may have accidently tried to root and flash my friend's Samsung Vibrant. It was going smoohtly but now, I'm all sorts of messed up.
The problem: I may have used the wrong kernel (zImage) when using heimdall-frontend (which I downloaded from xda). This is causing the phone to power on; it shows the Samsung Galaxy S 4g load screen, then Overstock, then the T-Mo logo sign (with the music), and then a longer Galaxy S load screen. After the load screen, the screen goes completely black, but all the touch buttons light up. Once like this, I can turn it off, and make it go back into recovery mode and also download mode.
Please help. I've been trying to solve this with my friend for about.. 4 hours.
P.S. I've looked up all the guides for using ODIN to get back to JFS, none works due to the reason that when I put it back into download mode, the computer does not recognize it. But it does at the same time. (it shows the "safetly remove hardware" and says that is an "USB mass storage device" ((but does not appear in "My Computer" when in the unresponsive screen-- but when in the download screen, it shows the same thing, only labeled "SAMSUNG USB Composite Device", which also cannot be accessed through "My Computer")
P.P.S. I'm sure it is a Samsung Galaxy S Vibrant, exclusive from T-Mobile. My computer is Windows Vista 32-bit, and I have as many Samsung drivers as humanly possible when it comes to the Vibrant.
Can anyone help a poor fool?
Click to expand...
Click to collapse
Sounds like you used the wrong odin files. if your screen is showing a galaxy s 4g logo then you must have mistakenly flashed a galaxy s 4g odin/heimdall package. on the back of your phone what is the model number. What on earth is JFS? ive heard of JFD which is the stock firmware that the phone shipped with.
If you flashed the wrong bootloader you are more or less stuck between a rock and a hardplace and will require a jtag. now the fact that teh screen does turn on is a good thing.
You need to keep trying to get it into download mode maybe try using a jig. Once youve gotten it into download mode try every single usb port you can find on your pc. When i need to odin i need to use one of my usb ports on the rear io panel none of the others will work. Once you get odin running and recognizing your device use the files posted in my sig as the odin files. any others and i cant help you cuz i dont know what your source is. Odin should be able to recover your device if it is still booting to the splash screen.
If for whatever reason you cant boot into download mode but can get into recovery here is what you do: make sure you have the android SDK installed (dont know what that is go here: http://developer.android.com/sdk/index.html and follow their directions) then open up command prompt while in recovery type the following command: adb reboot bootloader this should put you into download mode. If nothing ive mentioned works you may require a JTAG there is a company called MOBILETECHVIDEOS (http://mobiletechvideos.mybigcommerce.com/) that has a JTAG service.
Good luck
-Cheers

Related

new to the vibrant, maybe i bricked it

i picked it up used with stock rom, no mods. i rooted, then installed nero v3 with voodoo and then v5 with voodoo.... then i tried a custom battery mod and it screwed my phone up... cant get past the vibrant start screen, cant read the ext sd and the phone drivers will not work... computer detects it, but no drivers are installed. i have used the 32 bit driver 64 bit drivers, kies, kies mini, odin v1 and v1.7, still nothing... i can get into cwm recovery, but only with voodoo enabled, and can get into download mode, but i cant seem to get the computer to read it. have used 4 different computer, win 7 and 32 bit xp....also have tried drivers with pdanet and easy tether, but still no luck... can you offer any help to me??? thanks in advance.
as of u have done so much and nothing helped i would cry , and for not readin on how to unbrick your phone right on top of the forum you should cry too .
and if look good enough every 3rd thread that is made is how to unbrick the phone
@bartek
OK...OMG dude... you had like 5 posts 3 days ago...how are you helping this individual out other then giving him all your illegible ramblings that you are posting and ridiculing individuals as you go .. I'm sry, I don't mean to rant but damn...
Anyway OP, your just soft bricked. If you can get into d/l mode then I would either go ahead and ODIN back or if you can get into CWM recovery and you still have Nero 5 in your root, I would just reflash it and it should take care of it...enable voodoo when you flash Nero 5 ..you should be ok.
First off, I have been searching the forums for almost two weeks now and cannot find a solution....I have tried everything......the first problem is that no matter what drivers I use, the computer still says usb device not recognized, so I cannot get odin or heimdall to communicate, neither kies or kies mini.....
Well, now I turned it on this morning and I cannot get into cwm or dload mode.....just keeps bootlooping and linda talks and says riskful operation, then reboots......I am lost, don't know what else to do, I'm gonna throw this phone out the window
Sent from my HTC Vision using XDA App
bouzouki said:
First off, I have been searching the forums for almost two weeks now and cannot find a solution....I have tried everything......the first problem is that no matter what drivers I use, the computer still says usb device not recognized, so I cannot get odin or heimdall to communicate, neither kies or kies mini.....
Well, now I turned it on this morning and I cannot get into cwm or dload mode.....just keeps bootlooping and linda talks and says riskful operation, then reboots......I am lost, don't know what else to do, I'm gonna throw this phone out the window
Sent from my HTC Vision using XDA App
Click to expand...
Click to collapse
I would say Odin is your friend. go back to stock and start over Here is a start
http://www.youtube.com/watch?v=KyAIUOYufrU
Part 2: http://www.youtube.com/watch?v=33I-aNCypVM
hope this helps you
no dont throw the phoine out give it to mee ! or u can just remove your battery while phone is hooked up to computer with usb push volume up and volume down hold it put battery in , yellow android showed up ? u good to odin if he didnt redo repeat those steps until u will see him
how can i get odin to communicate when the computer wont read it?? it says usb device not recognized and no matter which drivers i install, it wont communicate.... and plus odin wont connect, i have tried multiple times.....heimdall drivers wont install either, it gives me a failed result.... i have used the 32 bit drivers, 64 bit drivers, kies, kies mini for vibrant, odin, heimdall, everything.... i have a g2 and have done so much to it with no problems, this phone has got me confused...
u need damn download mode for odin to see your phone damn could you just do those steps that i told you ? and btw open up odin so u can see when u phone is detected it will light up i nyellow
onc3 again
1. phone connected to computer
2.odin open
3.take out battery (out of your phone)
4.hold volume up volume down (allthe time)
5.put battery back in
6. put files in odin flash back
bouzouki said:
how can i get odin to communicate when the computer wont read it?? it says usb device not recognized and no matter which drivers i install, it wont communicate.... and plus odin wont connect, i have tried multiple times.....heimdall drivers wont install either, it gives me a failed result.... i have used the 32 bit drivers, 64 bit drivers, kies, kies mini for vibrant, odin, heimdall, everything.... i have a g2 and have done so much to it with no problems, this phone has got me confused...
Click to expand...
Click to collapse
I gotcha.... not to sound like an idiot but have you tried a different usb port? If your using one on the front, try ones in the back if your on a desktop.. if that doesnt work try running ODIN in XP SP3 compatibility mode
bartek25 said:
u need damn download mode for odin to see your phone damn could you just do those steps that i told you ? and btw open up odin so u can see when u phone is detected it will light up i nyellow
Click to expand...
Click to collapse
I think he's saying that odin doesn't detect his phone and therefore doesn't light up yellow. Happened to me too. I'm on the epic. I tried everything. But odin finally found my device. Try different usb ports, a different wire, reboot both phone and pc. Switch between usb debugging on and off. Try it with sideloading enabled and not. I eventually found a combimation that worked. These phones are fickle. It'll work eventually.
Sent from my SPH-D700 using XDA App
+1 on what he said above try connectin and disconection your phone lots of times 2 forgot it happend to me too once .sorry it was a while ago
i have used front usb ports, and the back ones, have even used 3 different computers. but same result. will odin connect even if the driver are not installed correctly and the computer doesnt recognize the usb device? and also, now i have the problem where i cannot get the phone into dload mode, it keep bootlooping to the samsung vibrant start screen and linda says riskful operation.
bouzouki said:
i have used front usb ports, and the back ones, have even used 3 different computers. but same result. will odin connect even if the driver are not installed correctly and the computer doesnt recognize the usb device? and also, now i have the problem where i cannot get the phone into dload mode, it keep bootlooping to the samsung vibrant start screen and linda says riskful operation.
Click to expand...
Click to collapse
As far as I know, ODIN wont recognize your phone without being in download mode and drivers installed on your computer.
bouzouki said:
i have used front usb ports, and the back ones, have even used 3 different computers. but same result. will odin connect even if the driver are not installed correctly and the computer doesnt recognize the usb device? and also, now i have the problem where i cannot get the phone into dload mode, it keep bootlooping to the samsung vibrant start screen and linda says riskful operation.
Click to expand...
Click to collapse
No I believe you need the correct drivers installed. At this point either your missing something or don't have the correct driver to install. Maybe someone can point out where all the proper drives are for you to download
speachless ....if u wont follow what i wrote im helpless.goodbye. and why u turning your phone on dude download mode is battery out phone connected to ANY usb port hold vol up vol down hold all time and puit battery in
if that doesent help your phones usb is **** or the cable is ****
btw, i have tried installing all the proper driver from the proper threads... 32 bit, 64 bit, ive tried kies and kies mini for vibrant, heimdall drivers also.... NOTHING WORKS...
i appreciate everones help... thank you.
This is what I do to get it working. I open odin first and load all the needed files.
I then plug the usb cord into the usb first before plugging it into the phone.
with odin open and the phone completely off. I hold down the volume rocker and plug in the usb. I get download mode to work almost everytime.
For me the stock cable I got with mine doesnt work. I have to use a different cord or it acts like it doesnt see my phone.

HELP!

I might have accidentally bricked my SGS 2. I get a screen saying:
"firmware upgrade encountered an issue. Please select recovery mode in kies and try again"
with a mobile phone and a computer logo with a Yellow triangle in between.
I know abt Rooting and ROM flashing etc and has been doing it for the last couple or years.
I flashed Franklin's XXKG3 Kernels, and before I could flash Chainfire's XXKG3 kernel, the USB ports refused to recognize my handset. I can still go into download mode but the Odin or Samsung Kies etc. won't do nothing.
Keeps saying "USB Device not recognized"
Please help!!!!
leo13aug79 said:
I might have accidentally bricked my SGS 2. I get a screen saying:
"firmware upgrade encountered an issue. Please select recovery mode in kies and try again"
with a mobile phone and a computer logo with a Yellow triangle in between.
I know abt Rooting and ROM flashing etc and has been doing it for the last couple or years.
I flashed Franklin's XXKG3 Kernels, and before I could flash Chainfire's XXKG3 kernel, the USB ports refused to recognize my handset. I can still go into download mode but the Odin or Samsung Kies etc. won't do nothing.
Keeps saying "USB Device not recognized"
Please help!!!!
Click to expand...
Click to collapse
Might help to reinstall KIES or try another computer.
Keeps saying "USB Device not recognized"
USB drivers problem remove Kies totally and reinstall .
Connect in mass storage mode and let windows find drivers .
That fails its broken phone .
jje
you broke your phone.
buy another SGS II
You can always try using a USB JIG to put the phone in download mode.
leo13aug79 said:
Keeps saying "USB Device not recognized"
Click to expand...
Click to collapse
Uninstall the Samsung USB Driver from Control Panel
START/Control Panel/Programs and Features
Select "SAMSUNG USB Driver for Mobile Phones" and then uninstall
reboot your PC and then re-install the Samsung USB Driver from:-
C:\Program Files\Samsung\Kies\USB Driver
and run "SAMSUNG_USB_Driver_for_Mobile_Phones.exe"
Doing that will make sure there is no USB driver corruption.
"firmware upgrade encountered an issue. Please select recovery mode in kies and try again"
Click to expand...
Click to collapse
I had the same problem on my SGS4g after updating to a leaked 2.3.4 rom, which would not make phone calls. Tried to use heidmall to downgrade by loading a new rom. After installing the usb driver as described here http://forum.xda-developers.com/showpost.php?p=14798367&postcount=1 . After reboot I get the error screen <phone..!..Computer> "firmware upgrade encountered an issue. Please select recovery mode in kies and try again". I then took the following steps.
I came across this site: http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series#Bricked_Screen Under the bricked section it mentions a couple things to try. I the reboot cycle with a couple of times and kept on getting the same screen. Still no go.
I took Odia's advice an did a complete removal of all usb drivers as mentioned and reinstalled kies. This was key in getting odin to recognize the phone again.
My solution:
I try Odin again to try to get it to recognize my phone. I open odin with the usb connected in this state and it is not recognized. I pull battery, it boots to error screen. I restart odin and then plug in the usb and it is recognized. I was then able to load my pit, pda, phone, csc back onto the phone with odin. The first time it tried to load the data it failed, the second time it worked!
Interestingly I never got the "Download Screen". I was still on the mentioned error screen, yet odin was able to still see the phone. The status bar still showed up on the error screen as the fresh rom was being loaded.
I thought I was totally bricked, but this method worked in my case. Hope something similar might work for you.
I still don't know I would get this error screen and have to go through this after loading the required usb driver for heimdall? Any ideas?
OMG! It's WORKING!
Thanks a lot to you all guys for the co-operation....
So, what did I do???? I uninstalled Kies and re-installed a couple of times but it won't access it. Tried Odin in all possible ways, No success. While playing and after ordering a "Jig" from some1 in USA,
I thought of something else and while the phone still being connected with the pc, I ran SuperOneClick, but it went on saying waiting for the device,.... I accidentally or in frustration hit the "HOME" button and it started doing something, USB drivers and Modem drivers installed on PC. Then I started Odin and the port went "Yellow". And I flashed it with the XXKG3.....
OMG! I'm so much relieved!!!!!!!! thanks God
thank you all too
Love your SGS2 and love God! Bless you all!
fvnktion said:
I had the same problem on my SGS4g after updating to a leaked 2.3.4 rom, which would not make phone calls. Tried to use heidmall to downgrade by loading a new rom. After installing the usb driver as described here http://forum.xda-developers.com/showpost.php?p=14798367&postcount=1 . After reboot I get the error screen <phone..!..Computer> "firmware upgrade encountered an issue. Please select recovery mode in kies and try again". I then took the following steps.
I came across this site: http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series#Bricked_Screen Under the bricked section it mentions a couple things to try. I the reboot cycle with a couple of times and kept on getting the same screen. Still no go.
I took Odia's advice an did a complete removal of all usb drivers as mentioned and reinstalled kies. This was key in getting odin to recognize the phone again.
My solution:
I try Odin again to try to get it to recognize my phone. I open odin with the usb connected in this state and it is not recognized. I pull battery, it boots to error screen. I restart odin and then plug in the usb and it is recognized. I was then able to load my pit, pda, phone, csc back onto the phone with odin. The first time it tried to load the data it failed, the second time it worked!
Interestingly I never got the "Download Screen". I was still on the mentioned error screen, yet odin was able to still see the phone. The status bar still showed up on the error screen as the fresh rom was being loaded.
I thought I was totally bricked, but this method worked in my case. Hope something similar might work for you.
I still don't know I would get this error screen and have to go through this after loading the required usb driver for heimdall? Any ideas?
Click to expand...
Click to collapse
I love you man! You saved my phone and me!
So what have we learnt today? Don't go screaming "brick!" everytime you encounter a problem
I had a same issue yellow triangle between Phone and PC symbol...
followed this step .. http://forum.xda-developers.com/showthread.php?t=1274337
just did like this on very first step to get into odin mode hold vol down and power for longer then usual to get into odin mode and by pass that yellow triangle between Phone and PC screen and then follow rest of it same and easy as right clicking on desktop LOL!
From my experience, only true brick I encountered was when I messed with boot loaders. If the screen shows anything at all, Odin will recognize it. Glad to hear it's fixed
Sent from my GT-I9100 using XDA App
Odia said:
Uninstall the Samsung USB Driver from Control Panel
START/Control Panel/Programs and Features
Select "SAMSUNG USB Driver for Mobile Phones" and then uninstall
reboot your PC and then re-install the Samsung USB Driver from:-
C:\Program Files\Samsung\Kies\USB Driver
and run "SAMSUNG_USB_Driver_for_Mobile_Phones.exe"
Doing that will make sure there is no USB driver corruption.
Click to expand...
Click to collapse
I´d tried to upgrade my Infuse SGH-i997 (AT&T) but I did something wrong and now the cell phone no work.
When it turn on says:
"firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
The computer recognize the cell phone but I don´t know what else I can do.
Any suggestion?
Can you get into download mode? If yes then reflash stock firmware using Odin
Sent from my GT-I9100 using Tapatalk
A bricked phone is a phone which will not respond. It maybe a soft brick or hard.
If you can get into download or recovery all you have to do is reflash. Wipe data & Cache. You will be up and running. If your phone is not recognised by your computer then reinstall kies.
Sent from my GT-I9100
Yep. Infuse Q&A (You're in the wrong section).
anjimgo said:
I´d tried to upgrade my Infuse SGH-i997 (AT&T) but I did something wrong and now the cell phone no work.
When it turn on says:
"firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
The computer recognize the cell phone but I don´t know what else I can do.
Any suggestion?
Click to expand...
Click to collapse
Please use the Q&A Forum for questions &
Read the Forum Rules Ref Posting
Moving to Q&A
Well, I got this same Firmware upgrade error. I can't get the computer to see it at all. It's almost like the USB port doesn't work anymore. I can get into the download mode but then it ends there. I cannot get into the bootloader at all. If I try, it goes to the error screen and if I boot normally, it goes to the error screen.
Brittlespeed said:
Well, I got this same Firmware upgrade error. I can't get the computer to see it at all. It's almost like the USB port doesn't work anymore. I can get into the download mode but then it ends there. I cannot get into the bootloader at all. If I try, it goes to the error screen and if I boot normally, it goes to the error screen.
Click to expand...
Click to collapse
I can't tell if you're asking for help or just letting people know, but anyway, considering all your previous posts were in the Epic 4G Touch forums, you've probably trashed your device flashing something meant for the I9100.
See this thread for confirmation of your new shiny brick, if my above assumption was correct: http://forum.xda-developers.com/showthread.php?t=1492323
this solution worked for a Galaxy s3 mini
fvnktion said:
I had the same problem on my SGS4g after updating to a leaked 2.3.4 rom, which would not make phone calls. Tried to use heidmall to downgrade by loading a new rom. After installing the usb driver as described here http://forum.xda-developers.com/showpost.php?p=14798367&postcount=1 . After reboot I get the error screen <phone..!..Computer> "firmware upgrade encountered an issue. Please select recovery mode in kies and try again". I then took the following steps.
I came across this site: http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series#Bricked_Screen Under the bricked section it mentions a couple things to try. I the reboot cycle with a couple of times and kept on getting the same screen. Still no go.
I took Odia's advice an did a complete removal of all usb drivers as mentioned and reinstalled kies. This was key in getting odin to recognize the phone again.
My solution:
I try Odin again to try to get it to recognize my phone. I open odin with the usb connected in this state and it is not recognized. I pull battery, it boots to error screen. I restart odin and then plug in the usb and it is recognized. I was then able to load my pit, pda, phone, csc back onto the phone with odin. The first time it tried to load the data it failed, the second time it worked!
Interestingly I never got the "Download Screen". I was still on the mentioned error screen, yet odin was able to still see the phone. The status bar still showed up on the error screen as the fresh rom was being loaded.
I thought I was totally bricked, but this method worked in my case. Hope something similar might work for you.
I still don't know I would get this error screen and have to go through this after loading the required usb driver for heimdall? Any ideas?
Click to expand...
Click to collapse
Thanks a lot. My teenage son thought he had bricked his S3 mini but I was able to fix it after reading this thread. Thanks.

Did I brick the unbrickable phone?

I have been posting (and have had some nice people try to help) in the How to Recover Fascinate from any Brick thread for about a week and can't seem to find a solution. I have also searched the internet high and low looking for a solution with no success. Hopefully someone here has had the same issues and can point me in the right direction.
I rooted the Fascinate using a one click method and was able to get a Titanium backup but could not get into the proper recovery to do a system image. Stupidly, I flashed SP Recovery from within ROM Manager. From that moment on I when the phone is turned on it gets to the "Samsung" screen and locks.
I did my research and found out all I needed to do to fix is install ODIN and reflash the stock ROM again. The problem is that ODIN will not recognize the phone. I start ODIN, pull the phone battery, plug the phone into USB cable, push volume down to get the phone into download mode (Yellow Triangle). I keep getting USB Device Not Recognized errors from Win 7 (64-bit).
I tried installing Heimdall to load the correct drivers but it doesn't see the device either. I can connect my Droid or Droid 2 and Heimdall sees immediately so I know it is not a problem with the software or cable.
I have tried to install the correct USB drivers (even the ones listed on this site). I tried installing Kies and it doesn't see the phone either.
Since the phone is looping at the "Samsung" screen I can't change any settings in the phone as some have suggested. I really do not have any more ideas other that to use this phone as a very expensive door stop. Hopefully, someone here can help. Thanks in advance!!!
pscpa said:
I have been posting (and have had some nice people try to help) in the How to Recover Fascinate from any Brick thread for about a week and can't seem to find a solution. I have also searched the internet high and low looking for a solution with no success. Hopefully someone here has had the same issues and can point me in the right direction.
I rooted the Fascinate using a one click method and was able to get a Titanium backup but could not get into the proper recovery to do a system image. Stupidly, I flashed SP Recovery from within ROM Manager. From that moment on I when the phone is turned on it gets to the "Samsung" screen and locks.
I did my research and found out all I needed to do to fix is install ODIN and reflash the stock ROM again. The problem is that ODIN will not recognize the phone. I start ODIN, pull the phone battery, plug the phone into USB cable, push volume down to get the phone into download mode (Yellow Triangle). I keep getting USB Device Not Recognized errors from Win 7 (64-bit).
I tried installing Heimdall to load the correct drivers but it doesn't see the device either. I can connect my Droid or Droid 2 and Heimdall sees immediately so I know it is not a problem with the software or cable.
I have tried to install the correct USB drivers (even the ones listed on this site). I tried installing Kies and it doesn't see the phone either.
Since the phone is looping at the "Samsung" screen I can't change any settings in the phone as some have suggested. I really do not have any more ideas other that to use this phone as a very expensive door stop. Hopefully, someone here can help. Thanks in advance!!!
Click to expand...
Click to collapse
Control Panel/ User Account/ User Account Control settings- set to- Never notify- restart computer.
Should recognize phone. Reset to default when done and restart. Windows crap!
Thanks but this setting has always been set to "Never Notify"......any other ideas...please
I don't know nothing about it but the guy said " reset to default and restart (again)??
Sent from my SCH-I500 using xda premium
Followed the directions exactly. I think the OP wanted me to reset to default after I was done flashing. This is so strange....I figure if the people on XDA can't figure this out the phone is doomed.
Have you tried a different USB plug on the computer? Or a different USB cord? Or a different computer?
Sent from my SCH-I500 using XDA App
schu9120 said:
Have you tried a different USB plug on the computer? Or a different USB cord? Or a different computer?
Sent from my SCH-I500 using XDA App
Click to expand...
Click to collapse
I had to use a laptop to access my Fascinate because my desktop wouldnt even show it as unrecognized hardware, it was like it didnt even exist... I went in device manager and uninstalled all my usb devices, rebooted with everything but mouse/kb unplugged, installed SDK drivers for Nexus S, rebooted again (probably not needed but better safe than sorry) and I can now Odin into my phone... Hope this helps ya man... sucks bricking a phone
The Heimdall drivers won't work. Kies won't recognize it if it won't boot. There should be an option in Kies to install the driver. Drop down box in the top left corner. Did you try to install your driver that way?
have you installed the driver yet? samsung driver?

[Q] Galaxy Vibrant Hard Bricked

I was flashing my Vibrant back to the stock ROM using ODIN, and it seemed to have shut off during the procedure. I've used ODIN several times beforehand, but I never had any issues with it, until now. Upon booting my vibrant i was presented with an unusual looking semi-brick screen. After a bit of research, I found out that there was a program, developed by Adam Outler, that supposedly would be the solution to this issue. Though, once it was installed, another issue arose. The Vibrant was not recognized by my laptop. Is there any possible solutions to my dilemma? I would greatly appreciate any support that can be provided
Below is a link an image of the screen that i am currently stuck on
i1209.photobucket.com/albums/cc398/jjjhhhppp/scan.jpg
This is a soft brick. Easily fixable. Go into my Miui guide, link in signature, and go to post two. The answer is there.
As for your phone not being recognized download a program called "Samsung Kies". Once installed it will automatically reinstall your drivers.
Sent from my SGH-T959 (Samsung Vibrant)
Installing Samsung Kies did not solve the issue, my phone is still not visible within Device Manager, ODIN is unable to find phone, Heimdall is unable to find the phone, Zadig states "0 devices found" even when the phone is connected, and finally, One-Click UnBrick gives me Unspecified Errors every time I try to run "unsoft brick"
Try to download the AIO Toolbox and reinstall the drivers that way. Then go back to NOOB's guide, post 2 and try again. Your image and his image has a striking similarity.
Also remember "You don't necessarily need the download mode image to be present. As long as you are getting the COM ID to light up yellow in ODIN, just flash back to stock like normal."
Ok, so after installing AIO toolbox and following NOOB's guide, still, my phone is not listed under ID:COM in ODIN, and it does not appear in device manager aswell. (Usually in device manager I would see "Gadget Serial", "Samsung USB Composite Device", "ADB Interface", "Samsung Mobile Modem 2", or something similar when the phone is connected)
jjjhhhppp said:
Ok, so after installing AIO toolbox and following NOOB's guide, still, my phone is not listed under ID:COM in ODIN, and it does not appear in device manager aswell. (Usually in device manager I would see "Gadget Serial", "Samsung USB Composite Device", "ADB Interface", "Samsung Mobile Modem 2", or something similar when the phone is connected)
Click to expand...
Click to collapse
Have you tried all of the button combinations for a forced download mode? I have nearly hard bricked once beofre, or so i though. My phone wouldnt power on at all, or atleast didnt give me an indication that it was booting. ie. no buttons lighting, etc. your phone is NOT boned. Try pulling the battery and letting it sit for a few minutes..
Once you do that, reinstall the windows drivers. as an added precaution, run odin as an administrator (even in xp). Flashing back to a stock rom probably wouldnt hard brick your pone, as I dont believe the stoc rom writes a new bootloader.
Try this :
1. Plug in USB cable (to PC)
2.Remove battery, simcard, memory card from phone.
3. Hold ONLY vol up/ voldown
4. Plug usb into PHONE.
5. Insert Battery (after inserting battery release the buttons)
6. Lastly, make sure your pc speakers are turned up, listen for the usb connect sound.
LIke i said, you dont have a hard brick. I believe the hard brik will either result in a reboot loop (not in all cases), or a black screen (someone else can chime in ad correct me). Just keep trying, you'll get it.

[Q] Sprint Galaxy Nexus Bricked? Help Please

I recently upgraded my radio for my Sprint Galaxy Nexus (toroplus), but i was unable to connect to the internet. I could make calls and send/receive texts, but no network connection. I decided to try to go back to stock. I saw a post saying to use odin to revert to stock. I ran it but go an error while it was flashing the cdma radio. It got stuck and wouldn't do anything, so i took out the battery. Now i cant get into download/odin mode or fastboot. The only thing that i seem to be able to do is connect back to odin, but it wont finish the process. When turning on the phone i only get a screen that has a phone to the left a monitor on the right and a triangle with an exclamation.
Has anyone had this problem and does anyone know how to get out of it?
I appreciate any help i can get.
Sprint Samsung Galaxy Nexus
SPHL700KIT
That screen you see is download mode. If your phone boots at all it is not bricked what so ever and can be recovered. Instead of using odin I would recommend having a look at doing it manually via adb and fastboot, that way you know exactly where something may have gone wrong. If you reflash the whole stock cdma img it should boot fine. Have a look in the GNexus dev section for info about fastboot and adb if required.
Sent from my Galaxy Nexus
Thanks, But its not download mode
I used download mode before,so i'm pretty sure its not it, unless their are two versions of it. I have tried using adb/fastboot, but when i do "fastboot devices" it doesnt even see it anymore.
Thanks for your quick response.
What screen are you on when you run the command adb devices? Recovery /download?
Sent from my Galaxy Nexus
neither. I cant get to either of them. they no longer work. Ive tried and tried to get to download, fastboot,& recovery, but all i can get to is the stupid error screen. I think somewhere in the process i corrupted/deleted them.
also my pc detects the phone as "samsung mobile usb cdc composite device" and "samsung mobile usb modem #2"

Categories

Resources