Hello,
Is anyone selling a keyboard cover for the Asus Transformer Prime, TF201, docking Keyboard? I am referring to a clear plastic cover to protect the keys from dust & spills.
Cheers,
Phil
The 1980's called, they want their pocket protectors back.
As far as I know there are no clear covers available for the keyboard keys.
However since the keys are fully recessed into the keyboard tray, it should be possible to cover them with any flexible clear plastic film if you are afraid of spills.
For instance you could buy a clear Skinomi screen protector like this one:
http://www.skinomi.com/sk9728-asus-transformer-prime-screen-protector.html
And then cut it to fit over the keyboard so that it sticks to the metal edges around the keys. That should give you what I think you are asking for.
Related
Arrrrgh! I'm wondering if anyone has found a (leather) flip case for the AT&T Tilt 2 they are happy with?
My phone is a little over a month old, and I'm getting desperate. I've been temporarily using a clear thing (case mate) AT&T sold me with the phone (it was all they had that would fit) until I found something that would work for me. I've been reading here, and finally took the plunge to get the Designio case discussed here:
http://forum.xda-developers.com/showthread.php?t=584093
Unfortunately, either I got a bad case or I'm being too picky or whatever, but I'm not pleased.
My criticisms are:
The PTT button completely covered by the leather support piece (not sure that's what to call it, but there's a leather piece that runs along the left edge, or bottom with the keyboard open). The PTT button is still functional as long as I press the leather piece just right.
The plastic over the keyboard does not fit snuggly -- it bulges up about an eighth of an inch along the bottom of the keyboard (the left side of the phone), which is annoying enough when using the keyboard, but that bulge also keeps that edge of the phone from closing flat when then keyboard isn't out. I carry my phone in a dedicated pocket in my purse, and I'm constantly finding dust & such that gets under the loose plastic keyboard protector at the bottom of the keyboard (left side of the phone when the keyboard is closed) since there's a gap along that edge from the loose plastic. That's highly annoying for me.
#2 might not be much of a problem if the magnetic closure was snug, but it's not -- IMO, it's off by a little over a quarter of an inch. This allows the top cover to slide around enough that the screen isn't protected when the case is closed (particularly the bottom of both sides up about 2.5" and up to 1/2" in from the bottom corners). If the magnetic catch was appropriately placed, it could also eliminate the gap on the left side of the phone when the keyboard is closed.
Clearly, this isn't the perfect case for me. I thought perhaps I was being too picky, but the Krusell case for my old 8525 doesn't suffer from these problems.
So, if anyone has found a flip case (preferably leather, but that's not a deal breaker) for the AT&T Tilt 2 that doesn't suffer from these problems, please share
TIA,
Saundra
i'm not entirely happy with mine, but mine seems not to have the problems that you are finding wiht yours.
i use the Capdase case, http://www.capdase.com/en/product4.php?cid=1&bid=5&mid=48, and it's a soft leather case that comes in two styles, either a "book"/side flip, or the top flip which i got.
main pro is that it uses small tabs on all 4 corners to clip on to the lower/keyboard half of the phone, allowing you full access to all buttons, the usb port, and the keyboard, without any plastic in the way. the tabs also seem to be more robust and likely to last longer than the seidio innocase tabs which i used on my kaiser. those tend to wear down and break off after about 2 years of use.
on the cons, i dislike the flap, which only has room to store 2 microsd cards and 1 extra sim card. i've already lost 1 sd card, though i am not 100% certain if it was my fault or the case (i was showing the phone to some friends the night i lost it). it also does not have any storage space for a credit card or similar, even though it would've been minimal cost to add one.
if only i could have the flap from your case, and the base of mine. then it'd be perfect.
Thanks for the input! It does sound as though we could have the perfect case with your base & my flap.
I'm in the US, and I couldn't find any retailers for that particular Capdase -- lots for iPhones. Of course.
It looks like I could maybe get it through eBay, which is good to know in case I just can't get the Designo to work for me.
Thanks again!
sslund said:
Arrrrgh! I'm wondering if anyone has found a (leather) flip case for the AT&T Tilt 2 they are happy with?
http://www.noreve.com/brand/HTC/product/Housse_cuir_HTC_Touch_Pro2_Verizon_-_Sprint_Tradition.html -This works well for me, but there are no pouches for SD cards
Click to expand...
Click to collapse
Noreve
I am using the Noreve case available at www.noreveusa.com I like it a lot. It too covers the push to talk button, but since I'm using a custom ROM it has no functionality anyway. The Piel Frama case I had for my Original Touch Pro, there was that darn plastic sheet covering the keyboard and frankly I think that sucks. Granted the noreve case is squirrely when the keyboard is open, but unless you are able to drive and text or ride a bike and text or a motorcycle and text, well you'd do better to spend your money on a funeral plan than a case. My only complaint about the Noreve case is the belt clip sucks. I am using an old Piel Frama belt clip since it fits my belt better. I also personally LIKE the looks of the larger Piel Frama TP2 case, but most have commented on how ugly it looks.
If you're crafty...
As we've come to realize, ATT has delivered the Tilt 2 in a state that requires serious hacks to make the simplest changes. In keeping with that line of thought, I've modified a clear plastic case and added a leather flap with a pocket for credit cards and memory stix. And - Unlike some commercial flaps, when this flap is closed, nothing can slide out of the pocket. Here's how you can too...
Note to Boy Scouts: I've included more detail below than many of you here may need. After buying the case, reviewing the pix and the dimensions, you may be able to fore-go most of the tedious instructions below.
PIX
I've posted a series of pix on photobucket (sadly, I'm too new and untrustworthy to provide direct links to them here). To review the photos:
1. Go to the PhotoBucket website.
2. Click the Drop-down arrow on the right side of the "Search" box and select "People" for the search type.
3. Search for my id, "fractalcracker". Zoom in to view the 5 photos in the default album.
Plastic Case
Two-Piece (front and back) Plastic Case from the ATT store: $29.99 (ridiculous, yes I know...). Find it online at the ATTWireless website by searching "Accessories" for part number "75525". The Back piece clips on to back of phone and allows you to access all buttons and slide open the keyboard. After adding this leather flap, you won't need the front piece of the case.
Leather Pocket Flap
The leather flap is similar to a wallet pocket. In fact you might be able to cut a wallet apart to make the flap. I'll give you directions to make this one by hand from a small piece of leather. If you don't have scrap leather, cut up your wife's (or your own) purse. Good luck with that one...
Leather Measurements:
You'll need a thin, pliable piece of leather 4 inches high by 5-1/2 inches wide. We'll cut 2 pieces as follows...
Outside flap piece:
3-1/4 inches wide from left to right.
4 inches high from top to bottom.
Pocket piece:
2-1/4 inches wide from left to right.
4 inches high from top to bottom.
Assembly
1. Cut leather pieces.
2. Lay the smaller (pocket piece) on the table so that what will be the 'hidden side' (inside of the pocket) is facing up. Align it so the narrow edge is closest to you.
3. Apply a thin bead of super-glue to the top, left and bottom edges of the pocket piece. The 4th, unglued side will be the opening of the pocket.
4. Lay the flap piece down on the table so the inside of the flap is facing up. Align it so the wide edge is closest to you.
5. Pick up the pocket piece and flip it over from left to right so the glue side is down. Align it above the right side of the flap piece and glue the 2 pieces together so the top, bottom and right edges are aligned.
6. To form the hinge, apply a thin bead of super-glue to the flap piece, running from top to bottom along its left edge (opposite the pocket).
For below - remember, we're only referencing the back side of the plastic case - not the front.
7. Lay the plastic case on the table, 'opening-side' up. Rotate it so the camera hole in the back cover is furthest from you. Slide the plastic case over so the right edge of the plastic case is aligned next to the left edge of the leather flap (pocket side up with pocket on the right side of the flap).
When we glue the flap to the case, we want the super-glued hinge joint to be about 1/16th inch below the face of the plastic case. That way, the leather flap will bend back enough to allow the phone screen to slide over it whyen you slide open the keyboard.
8. Stand the plastic case up by raising the left side and tilting it to stand on its right side. Align the right side of the case above the glue line on the left edge of the leather flap.
9. Press the right side of the plastic case down in place on the flap piece so the glue line on the leather flap is about 1/16th inch below the top face of the plastic case.
When it dries, press the phone into the plastic case and get on with your life!
May the force be with you...
Mark
It seems so simple.
A simple plastic clip with an adhesive back so I could clip my pen top edge of the screen (where the HTC logo is) when I'm not using it.
Would be SO helpful yet no one makes one. HTC are you listening? How hard would it be to include this with the tablet? Or how about with the pen you charge a fortune for?
I am going to look around. I bet something like this exists for holding a pen to a dry erase board or something and I can adapt it to the EVO.
Have an idea.
Think I'll just get a simple piece of black leather, cut a small strip, wrap it around my pen for fit and stick the ends to a small piece of double-sided foam tape. then just stick it to the top front of my View (where the HTC is) and presto, pen holder.
Or even easier, get a long thin strip of velcro and stick it along the top front of the tablet, then take a long strip of the soft fuzzy side and stick it to my pen. That should hold it pretty well while I'm typing on the tablet.
Another solution I have found is to add a cap with a clip to the back of the pen (a sharpie cap fits perfectly). Then attach this to a tether that fits into the headphone jack (many capacitive styli come with this tether). The pen dangles a bit, but what the heck, it is safely attached.
Flaco05 said:
Another solution I have found is to add a cap with a clip to the back of the pen (a sharpie cap fits perfectly). Then attach this to a tether that fits into the headphone jack (many capacitive styli come with this tether). The pen dangles a bit, but what the heck, it is safely attached.
Click to expand...
Click to collapse
Thanks. Yes, I thought of this as well but i hate the dangling pen part. Will post photos of whatever I come up with.
Not sure if this helps you in your search. I use a clip from a 2 dollar in line air blower or a pencil tire pressure gauge … fits the pen perfect.
Here’s a pic http://dl.dropbox.com/u/5220128/clip1.jpg
I have my flyer in a Blurex case and the pen snaps onto the closing latch.
I could have gotten a case with a pen holder. The problem is that I use the note app to do some.pretty hardcore thumb typing as I'm on the phone. In order to fly the tablet has to be comfortable in my hands. This means no bulky case so I just have a simple protective case on the back and no pen holder.
Sent from my PG41200 using Tapatalk
google pen pal -- Slim rubbery pen clip holder with adhesive
I think they have them on amazon
cheap too -- 5 in a pack for like $4
Magickly said:
google pen pal -- Slim rubbery pen clip holder with adhesive
I think they have them on amazon
cheap too -- 5 in a pack for like $4
Click to expand...
Click to collapse
Thanks for the lead on that. I want a black one and it seems they are selling every possible color except black. Oh well.
In the meantime I've come up with a simple solution that has the benefit of not adding thickness to my tablet when I put it in it's sleave or in my pocket.
It is just simply some velcro tape applied as show in the photos. Works a charm.
Thanks Kudzus for your idea of the tire gauge pen clip. It works perfect for me. Thanks!
It didn't scratch the finish off your pen like one of the other members stated?
I purchased this, from amazon:
MoKo(TM) Flip Stand Cover Case for ASUS Transformer Pad TF300 and Multi-Functional Docking Station (Compatible WITH or WITHOUT Keyboard Dock), Black and the MoKo screen protectors
I like the fit, however touching the top portion of the screen (when using keyboard) is slightly irritating as the cover gets in the way.
The screen protector feels solid and is glossy - no distortion as far as I can tell.
Came out to about 26.00.
update after a couple of days use,,,
love the screen protector
the case top edge (power button side) bugs me to no end when trying to switch tabs...
Hello Android fans,
I'm a new user to the Samsung Galaxy Tab 2 10.1 from T-Mobile (SGH-T779), and I wanted to discuss my case and screen protectors of choice I like.
First of all, my screen protector of choice in most cases is usually Zagg's invisibleShield, because it works REALLY well, most of the time. I say most of the time for reasons not related to this situation. I have a Galaxy Note 2 as well with a wallet case that presses against the screen, Zagg's plastic technology doesn't work so well for it in that kind of situation.
Otherwise, my Tab 2 has a nice wet-applied Zagg invisibleShield HD screen on it, and it's plain awesome. There's no quality loss in the screen, it doesn't scratch very easily and doesn't collect a whole lot of fingerprints. It does collect them, but easily wiped off with a simple cloth.
My case I'm using, though it's not /perfect/, it's just currently the best I could personally find at the time.
It's the RooCase RC-GALX10TAB2-DA-BK Dual-Axis leather folio case. Basically it works using a 2-piece assembly. The main part holds the case in a nice felt-feeling case, so you can hold it, without the outer case, in a night light package. The outer case has velcro to hold the inner part to it so you can rotate it by sticking it to the velcro. This allows it to be in landscape or portrait mode very nicely, and it doesn't fall over when in portrait mode like a lot of the other dual-axis folios seem to have a problem with. It does use a low-powered magnet on the front of the inner case to the outer inner case so it snugs together when closed.
The only downsides are, so far:
The stylus/pen holder is on the outside edge of the outer case, so it sticks out like a soar thumb, and can easily be knocked out.
The case has no hole on the bottom side for the 30-pin connector, though this issue can be kind of gotten around by simply rotating the tablet to its side, or completely upside down, thanks to full auto-rotation of the Android interface. I usually plug it in every night in this manner, rotated out to put the 30-pin on the outer side and plugged in.
It is "technically" leather, but it seems like every other "Genuine Leather" product out there, where the leather is just a very very thin layer of leather covered over cardboard or other fillers. (I make leather stuff as a hobby, so I know what real leather is capable of and feels like when done properly).
The plus sides are:
It fits rather well and does not interfere with the touchable screen area, even with my big hands I have yet to conflict with the edges of the touchable screen. .
It fits very snug and tightly, so it doesn't move at all.
It fully exposes the power, volume rocker, microSD slot, IrDA port, and headset port, and covers most of the SIM card, so it helps prevent loss of the SIM card in case it ever popped open and somehow snapped out.
Anyway, that's my review, hope it's helpful to people.
Psi-Jack
Hey I'm looking for a case with a hard cover that doesn't bend - like a keyboard case or a case with a kickstand. It also MUST attach to the tablet in a way that allows the tablet to swing freely but it doesn't matter if it's via magnet or hinge.
It doesn't matter if it has a keyboard and the quality of the keyboard doesn't matter as I won't be using it.
The Zagg Folio 8" Auto-fit looks perfect - except it's WAY more than I want to pay. Can anyone please recommend any other cases that are lower priced? The feature that I need is a non-bending cover that attaches well, anything else like keyboard or looks is unimportant. Thanks!
Reason I need a non-bending cover is I want to hang the tablet so it hangs on a monitor with the cover portion laying flat on the top of the monitor so it's at eye level for use on a stationary cycle and so the monitor screen is covered. The two bendy covers that I've tried this with "collapse" and the weight of the tablet drags off the top.
I have an idea: Why not use Velcro stickers so it can hang of the top(back) of the display unit itself? It would be way cheaper if you already have something in mind and can be easily removed. And even the slimmest stickers could be left on the cover without interfering with the screen once it's closed or when held while in use.
Nice idea but it's for a machine at my gym.