Hi everybody,
i'm stuck on WSOD.
I stil can access bootloader, the red,green,blue, white screen.
It displays as follow:
PB81100 HX-BC
SPL-2.0.8.HSPL 8G XE
RIFFBOX 0x05
Any clue on how to get out of this?
Thanks in advance
bump!
is the phone bricked?
No its not bricked.
Download a stock ROM from the HTC support site for your country with your S/N,connect your HD2 while on the bootloader (colored screen) and start flashing the ROM.
I think you can also get the spesific ROM for your device from here at the ROM Development section.
Hi, htc site downloads only the latest rom, i can't find the section where to put a serial number... anyway, i've downloaded the latest one for my country and from the SD it stucks on grey screen "Loading..." from USB it stucks on 0% (black screen with loading bar and no HTC logo)
Do someone knows where the htc site accepts s/n for downloading?
Can you tell what version of HSPL and FW do you have ,and what is your original FW country?
Edit:
http://forum.xda-developers.com/showthread.php?t=623283
In this thread you can find the official stock ROM of your device.
1-download it to your PC.
2-Connect your phone to the computer.
3-Run the Active Sync.
4-Run the Downloaded ROM,I think its RUU,5- read and follow the on screen instructions.
hagba said:
Can you tell what version of HSPL and FW do you have ,and what is your original FW country?
Edit:
http://forum.xda-developers.com/showthread.php?t=623283
In this thread you can find the official stock ROM of your device.
1-download it to your PC.
2-Connect your phone to the computer.
3-Run the Active Sync.
4-Run the Downloaded ROM,I think its RUU,5- read and follow the on screen instructions.
Click to expand...
Click to collapse
I don't have a HSPL right now its a SPL 2.08.0000ii and the country is ITALY.
I've downladed the latest 3.14 rom from italian website and i've attached it by usb and tried to flash, stuck at 0%.
as far as I remember SPL 2,08 is not for the FW version 3.14 its for older ROM.
Ok here is what you have to do:
1-from this thread download and install the HSPL2,you should do this by downloading to your PC and connecting your HD2 to Active Sync,read the thread the information is there.
http://forum.xda-developers.com/showthread.php?t=611433
2-from this thread download one of these Custom ROMs,anyone you like,and install the same way you did the HSPL2 and through the Active Sync.Dont wurry too many ROMs to chose from if you dont like it.
http://forum.xda-developers.com/showthread.php?t=612580
3- Do lot of reading and ask anything that you want an explanation.
4-Wahtever you do dont Flash anything from you phones SD card! just through the computer with Active Syng.
hagba said:
as far as I remember SPL 2,08 is not for the FW version 3.14 its for older ROM.
Ok here is what you have to do:
1-from this thread download and install the HSPL2,you should do this by downloading to your PC and connecting your HD2 to Active Sync,read the thread the information is there.
http://forum.xda-developers.com/showthread.php?t=611433
2-from this thread download one of these Custom ROMs,anyone you like,and install the same way you did the HSPL2 and through the Active Sync.Dont wurry too many ROMs to chose from if you dont like it.
http://forum.xda-developers.com/showthread.php?t=612580
3- Do lot of reading and ask anything that you want an explanation.
4-Wahtever you do dont Flash anything from you phones SD card! just through the computer with Active Syng.
Click to expand...
Click to collapse
As for the point 2: how can i connect it to active sync if it does not boot?
i've tried all options of HSPL and it won't flash anything, any version 1.66, 2.08 or 3.03.
If you are on tri color screen the pc and Active Sync must be able to recognize it.
however if you cannot Flash the HSPL your only hope is that you Flash a stock official ROM of your Devices original country and to do that you must know the exact region for your FW.
Same also happened to me once,I discovered that my HD2 FW country was South East Asia !! so after downloading and flashin it evrything started working once again.
Anyway if it didnk work,just go to the below link and ask help there from a guy called Anthony,register or use you facebook account for faster reply,he ussualy hangs around there and is always willing to help.
http://www.gsmarena.com/htc_hd2-reviews-2957.php
hagba said:
If you are on tri color screen the pc and Active Sync must be able to recognize it.
however if you cannot Flash the HSPL your only hope is that you Flash a stock official ROM of your Devices original country and to do that you must know the exact region for your FW.
Same also happened to me once,I discovered that my HD2 FW country was South East Asia !! so after downloading and flashin it evrything started working once again.
Anyway if it didnk work,just go to the below link and ask help there from a guy called Anthony,register or use you facebook account for faster reply,he ussualy hangs around there and is always willing to help.
http://www.gsmarena.com/htc_hd2-reviews-2957.php
Click to expand...
Click to collapse
i'm on tri color screen, the pc recognizes it and the "serial" changes to "usb" but activesync says its not connected for sync.
i've tried to flash any stock italian rom from 1.43 to latest 3.14 and always stuck at 0%, only sometimes at 1% then reboot...
May be you should try reinstall your Windows mobile Center,look for updates,it looks more like a PC software problem than a phone,did you try a different computer?
hagba said:
May be you should try reinstall your Windows mobile Center,look for updates,it looks more like a PC software problem than a phone,did you try a different computer?
Click to expand...
Click to collapse
i've tried 3 pcs, 1 with windows 7 and two with windows XP, same results...
Can't flash radio
Hi there,
After some different succesfull android installations I decided to do a task29. After that I couldn't flash the radio. Even with SD-method (renaming nbh-file on SD-card) I kept a white screen with HTC-logo, no RDG info on the buttom of my screen.
Then I flashed a stock winmo rom, succesfully. However, I want to go back to android. First think of checking some roms on SD. They all seem to get stuck on booting (or what ever). No progress, even after maybe 30 / 40 minutes. This is not normal, right?
I am reluctant to flashing any other stuff, scared of bricking my phone.
Can any one give me good advise? Like how I can get SD-roms to work for starters.
Thanks,
Mike
hagba said:
May be you should try reinstall your Windows mobile Center,look for updates,it looks more like a PC software problem than a phone,did you try a different computer?
Click to expand...
Click to collapse
A repair centre has done a JTAG without success (or they say so).
is it possibile even JTAG fails?
Related
I got a friends hd2 several days ago and it was stuck on the White splash screen and wouldn't go further.
I tried Hard reset with keys and it didn't helped to get past that screen.
So i decided to flash a new ROM.
First I installed 1.42.HSPL on it to make myself safe and tried to install WWE version but failed at 9 %.
After this i tried near all the steps from another thread on the forum, the one of italian guy who tried almost everything.
Strange thing is that after trying several roms and failing all the times at 9 %, the phone once booted into windows, and i got this information from it:
Radio 2.05.51.05_2
G 15.28.50.07U
Rom 1.48.406.1 (71294) FRE
But after powering it off it didn't boot up another time.
Also there was a small damage on one of the battery pins but I think i managed to get it soldered from outside with soldering iron.
I also tried with MTTY and it didn't work either.
I got the official rom 1.48.406.1 FRE (because this phone is from swiss operator in french language) but it doesn't flash it goes to 9 % and gives error 290.
Ok, i started the thread because I actually wante to ask the question, why i'm unable to get into the Flash process from SD Card.
I formatted SD and copied the LEOIMG.nbh from official ROM and other ROM's too but when i press Reset and hold volume Down key sometimes nothing happens screen is black, sometimes im going into Bootloader with Serial shown and this text:
"Upgrade ROM code error. Please try again" and in the top right corner its written RUUNBH.
Anyone has any idea what could be problem of this device?
Btw I own LEO too and i never faced any problem till now, it was originally in German Language and i flashed it to WWE and didn't get any problems like this one.
gjizaqin said:
I got a friends hd2 several days ago and it was stuck on the White splash screen and wouldn't go further.
I tried Hard reset with keys and it didn't helped to get past that screen.
So i decided to flash a new ROM.
First I installed 1.42.HSPL on it to make myself safe and tried to install WWE version but failed at 9 %.
After this i tried near all the steps from another thread on the forum, the one of italian guy who tried almost everything.
Strange thing is that after trying several roms and failing all the times at 9 %, the phone once booted into windows, and i got this information from it:
Radio 2.05.51.05_2
G 15.28.50.07U
Rom 1.48.406.1 (71294) FRE
But after powering it off it didn't boot up another time.
Also there was a small damage on one of the battery pins but I think i managed to get it soldered from outside with soldering iron.
I also tried with MTTY and it didn't work either.
I got the official rom 1.48.406.1 FRE (because this phone is from swiss operator in french language) but it doesn't flash it goes to 9 % and gives error 290.
Ok, i started the thread because I actually wante to ask the question, why i'm unable to get into the Flash process from SD Card.
I formatted SD and copied the LEOIMG.nbh from official ROM and other ROM's too but when i press Reset and hold volume Down key sometimes nothing happens screen is black, sometimes im going into Bootloader with Serial shown and this text:
"Upgrade ROM code error. Please try again" and in the top right corner its written RUUNBH.
Anyone has any idea what could be problem of this device?
Btw I own LEO too and i never faced any problem till now, it was originally in German Language and i flashed it to WWE and didn't get any problems like this one.
Click to expand...
Click to collapse
Not sure if this is the problem, but what size is your SD card? I've heard, that sometimes is impossible to flash from larger cards, safest way is to use cards up to 2GB...
CaponiND said:
Not sure if this is the problem, but what size is your SD card? I've heard, that sometimes is impossible to flash from larger cards, safest way is to use cards up to 2GB...
Click to expand...
Click to collapse
Actually the sd is original 2gb that comes with hd2.
Friend, try to flash hspl 2.08 !!
Most likely that is the problem.
Enter the bootloader and connect it via usb to your usb and install 2.08 hspl (search fo it on xda developer forum)
Before instaling it read the instruction so that you know that hspl 2.08 can be installed over the old version of hspl that you installed!!
Oh and update radio to atleast 2.07
2.14 is very good
PS
Did you perform task29 before flashing?
mladen.p said:
Friend, try to flash hspl 2.08 !!
Most likely that is the problem.
Enter the bootloader and connect it via usb to your usb and install 2.08 hspl (search fo it on xda developer forum)
Before instaling it read the instruction so that you know that hspl 2.08 can be installed over the old version of hspl that you installed!!
Oh and update radio to atleast 2.07
2.14 is very good
PS
Did you perform task29 before flashing?
Click to expand...
Click to collapse
I guess I should try to install 2.08 HSPL, do you think i can use the same HSPL installer and just install 2.08 hspl from it? Because i already tried 1.66.HSPL but didn't worked.
And yes i performed task29 two or three times it finishes with some known output message which is stated on the original MTTY thread to be ignored.
Any other ideas?
gjizaqin said:
I guess I should try to install 2.08 HSPL, do you think i can use the same HSPL installer and just install 2.08 hspl from it? Because i already tried 1.66.HSPL but didn't worked.
And yes i performed task29 two or three times it finishes with some known output message which is stated on the original MTTY thread to be ignored.
Any other ideas?
Click to expand...
Click to collapse
you have to flash the HSPL back to 1.42 0000 ,then update the HSPL to 2.08 HSPL directly. if you flash it from 1.66. it can not work..pls be noted. good luck to you .hope you leo can be used again.
zengxisheng said:
you have to flash the HSPL back to 1.42 0000 ,then update the HSPL to 2.08 HSPL directly. if you flash it from 1.66. it can not work..pls be noted. good luck to you .hope you leo can be used again.
Click to expand...
Click to collapse
Ok I installed 2.08.HSPL from 1.42.HSPL and it went successfully, now i see 2.08.HSPL on bootloader but it still fails to update ROM. Stops at 8 % on the phone with rectangle mark, and on the pc it stops at 9 %.
I get Error 290 - Unknown Command
But why i cant go into sd card flash screen when i press reset and volume down ?
I just used another 2 gb microSD and added LEOIMG.nbh from official FRE ROM and it doesnt work.
Hey bud,
I was having the same problem: the flashing didn't want to start by doing a reset+vol.down. I somehow got around this by putting the leoimg.nbh on my mircoSD card, and then started the flashing from my computer by running the .exe that contains the RUU (for ActiveSync flashing). This "magically" triggered the flashing from the mircoSD card (it showed me a screen whether i wanted to update leoimg.nbh). On this screen, pressing vol.down would start the flashing through ActiveSync, and pressing the power button would start the flashing from leoimg.nbh from your microSD card. In the last case, the update on your computer will stall at 0%, this is just because you're not running the update from your computer, but from your phone. On your computer it will time-out, but the update on your phone will continue!
I hope this works! But you're doing this on your own responsibility ;p
ce3c said:
Hey bud,
I was having the same problem: the flashing didn't want to start by doing a reset+vol.down. I somehow got around this by putting the leoimg.nbh on my mircoSD card, and then started the flashing from my computer by running the .exe that contains the RUU (for ActiveSync flashing). This "magically" triggered the flashing from the mircoSD card (it showed me a screen whether i wanted to update leoimg.nbh). On this screen, pressing vol.down would start the flashing through ActiveSync, and pressing the power button would start the flashing from leoimg.nbh from your microSD card. In the last case, the update on your computer will stall at 0%, this is just because you're not running the update from your computer, but from your phone. On your computer it will time-out, but the update on your phone will continue!
I hope this works! But you're doing this on your own responsibility ;p
Click to expand...
Click to collapse
Hmmm this kinda messed me up.
What EXE file you run on the pc so it triggered update from SD ?
Because it's upossible to connect with activesync and browse to sd without the phone being fully operational (winmo running).
So i would say maby you just got it somehow with key kombination, because it would be impossible to run it the way you say. Or maby i'm wrong.
Could you be more specific about how you exactly run that process?
Thanks for your kind help. Gjizaqin
Well, whatever ROM you want to flash,
when you download this ROM, the .nbh file is packed in a .exe file.
You transfer the .nbh file to your microSD (rename to leoimg.nbh), and you can run the .exe file to flash through ActiveSync.
Because it's upossible to connect with activesync and browse to sd without the phone being fully operational (winmo running).
Click to expand...
Click to collapse
For me it was possible: reset your phone with the volume button down, to get to the tri-color screen. It shows "serial" on it. When you then connect your phone using your USB cable, it should switch to "USB", after which you can run the ActiveSync flashing.
ce3c said:
Well, whatever ROM you want to flash,
when you download this ROM, the .nbh file is packed in a .exe file.
You transfer the .nbh file to your microSD (rename to leoimg.nbh), and you can run the .exe file to flash through ActiveSync.
For me it was possible: reset your phone with the volume button down, to get to the tri-color screen. It shows "serial" on it. When you then connect your phone using your USB cable, it should switch to "USB", after which you can run the ActiveSync flashing.
Click to expand...
Click to collapse
Whell, by doing this procedure your doing normal ROM Update, and it's not doing update from sd card.
Anyways i tried this way too but not successful, its stuck on 8 % and stay's that way for about 3 minutes, than it gives me error 362 on the loader.
Anyways thanks for your help mate.
Anyone with experience can give me advice what to do with this phone?
Thanks in advance.
Gjizaqin
i'm doing task29 too... but it hang when it runs on black screen showing the percentage bar. advise is appreciated. Thanks.
whizzkid_cool said:
i'm doing task29 too... but it hang when it runs on black screen showing the percentage bar. advise is appreciated. Thanks.
Click to expand...
Click to collapse
I guess were on the same boat
gjizaqin said:
I guess were on the same boat
Click to expand...
Click to collapse
I have the same problem, tried all sorts with no luck. Can't get SD card install to work either.
Oh this sounds fun, I can no longer run active syn with my leo, the computer reports that my "usb device is not functioning properly"
I have re downloaded sync, try as I might I cant it back up and running, I wish everyone else the best of luck
This might be just a little bit off topic, but does anybody know how it is possible that some SD cards are good for flashing ROM's and other (mostly the larger) aren't?
Do you also need to copy the folder "program files" from the SD card you've flashed the ROM with to the other SD card, when you'd like to use this for your device?
jordy1990 said:
This might be just a little bit off topic, but does anybody know how it is possible that some SD cards are good for flashing ROM's and other (mostly the larger) aren't?
Do you also need to copy the folder "program files" from the SD card you've flashed the ROM with to the other SD card, when you'd like to use this for your device?
Click to expand...
Click to collapse
There has been reported problems with some 16GBmSD cards when it comes to flashing from them.
The only thing you need on the mSD card is the LEOIMG.nbh file.
dwntoearth said:
Oh this sounds fun, I can no longer run active syn with my leo, the computer reports that my "usb device is not functioning properly"
I have re downloaded sync, try as I might I cant it back up and running, I wish everyone else the best of luck
Click to expand...
Click to collapse
If you boot up your phone to Bootloader mode (but not connected to the computer), the bottom of the screen reads 'Serial'. If you now plug it into the computer, does it change to 'USB'?
Your computer error message is just saying that the computer cannot install a driver to communicate properly with your phone. Since your phone isn't fully loaded into WinMo then your computer isn't going to recognise it as a WinMo device. So don't worry about that message.
feridoun said:
I have the same problem, tried all sorts with no luck. Can't get SD card install to work either.
Click to expand...
Click to collapse
I guess this problem happen to some of the flash addicts! Problem still unsolved...
Hi...
Can anybody help, my Display is dying at the moment, and i want to send it in for repair,
but i need to restore the original bootloader,
can anybody help, download link for the bootloader and manual,,instruction..
Many thanks
Markus
I think you can download the official firmware somewhere, when you flash it everything should be back to the way it was.
What version of firmware do you need? WWE? T-Mobile? Orange?
If it's the WWE 2.73 version - click here - This will restore the phone to factory settings including bootloader/ROM/Default Settings e.t.c
Hello,
I tried to flash the UCP cited for the same screen problem. I checked my windows drivers are correct (sync between the hero and the perfect pc). Every time I have the same error message, 170 which would normally be bad drivers, which should not be my case since retry several times. I mark the following 170: wrong version of bootloader. The same thing happens whether on a PC or XP win7.
Does anyone have a solution please??
Armrhero said:
Hello,
I tried to flash the UCP cited for the same screen problem. I checked my windows drivers are correct (sync between the hero and the perfect pc). Every time I have the same error message, 170 which would normally be bad drivers, which should not be my case since retry several times. I mark the following 170: wrong version of bootloader. The same thing happens whether on a PC or XP win7.
Does anyone have a solution please??
Click to expand...
Click to collapse
There is a thread called "usb and ruu issues solved" by BTDAG. That should sort you out.
Sent from my HTC Hero using XDA App
Hello everyone, I just join here tonight after finding this site through google. I have been reading hours through the threads. Very interesting reading however I still could not find a solution for my problem.
I did a factory reset on my HD2 and now all that happens when I start the phone is a red, green, blue and white screen. It does not load to the windows mobile screen anymore.
On the red part of the screen it says:
PB81100 HX-BC
SPL-1.42.0000 XE
MicroP (LED) 0X05
MicroP (TOUCH) 0X40
The green and blue stripes have no text on them but the white stripe has "serial" on it.
I am confused why this had happened, any help to fix this problem will be much appreciated. Thank you.
Hello sir, and welcome on XDA.
- Try this take out your battery
- revert beck your battery without restarting your device
- hold volume down and volume UP press in follow by a short press on the power button.
- you will see your 4color screen shortly and then a grey screen with blue text.
- Press volume up to restore your device.
Try this and let us know.
Hi Kurt Willems, thanks for the reply however this method did not resolve the problem. Still the red, green, blue and white screen appears.
greyshade11 said:
Hi Kurt Willems, thanks for the reply however this method did not resolve the problem. Still the red, green, blue and white screen appears.
Click to expand...
Click to collapse
Did it get stuck somewhere ore did you saw all the posses like I mention but after the restart you cam's automatically back into the 4 color screen?
Do you recall what your original rom was? If you plug your device into usb port on pc, does serial change to usb? If so, I suggest reinstalling your original rom.
Yes I followed your instruction exactly, still the same striped screen.
greyshade11 said:
Yes I followed your instruction exactly, still the same striped screen.
Click to expand...
Click to collapse
Well like ClydeB1 mentioned, get YOUR stock ROM, connect your device to your pc and reinstall the stock ROM (At least if your device will connect)
"Do you recall what your original rom was? If you plug your device into usb port on pc, does serial change to usb? If so, I suggest reinstalling your original rom."
Hi ClydeB1, I cannot remember exactly what the rom name was, I think it started 4... I read some threads and tried some methods such as downloading the HD2 rom from the hTc website via entering my S/N number. Then I put that on the SD card and updated it using 7-zip.. changing the file name to "leoimg...." after a minute of updating the phone reboot and said it had an error, it reboot again and completed the update. But still i am faced with the striped screens.
kurt-willems said:
Well like ClydeB1 mentioned, get YOUR stock ROM, connect your device to your pc and reinstall the stock ROM (At least if your device will connect)
Click to expand...
Click to collapse
Hi, how do I get my stock rom? When I connect the usb cable to the phone it automatically shows this striped screen on the phone. The phone does not sync with the computer. I believe the phone was set to storage card when connected to the pc. But i cannot access the storage card via the phone. I access the storage card using a multi card reader.
greyshade11 said:
"Do you recall what your original rom was? If you plug your device into usb port on pc, does serial change to usb? If so, I suggest reinstalling your original rom."
Hi ClydeB1, I cannot remember exactly what the rom name was, I think it started 4... I read some threads and tried some methods such as downloading the HD2 rom from the hTc website via entering my S/N number. Then I put that on the SD card and updated it using 7-zip.. changing the file name to "leoimg...." after a minute of updating the phone reboot and said it had an error, it reboot again and completed the update. But still i am faced with the striped screens.
Click to expand...
Click to collapse
When you download from the HTC site, you'll get an exe file. You can try to run it from your pc, connect device to pc (still in bootloader screen ie striped screen) when serial changes to usb then run the exe file.
If that doesn't work then Right click and extract the exe file to your pc. Then take the RUU_signed.nbh file, rename that to LEOIMG.nbh and copy to root of sd card (formatted to FAT32). Then flash as you described.
ClydeB1 said:
When you download from the HTC site, you'll get an exe file. You can try to run it from your pc, connect device to pc (still in bootloader screen ie striped screen) when serial changes to usb then run the exe file.
If that doesn't work then Right click and extract the exe file to your pc. Then take the RUU_signed.nbh file, rename that to LEOIMG.nbh and copy to root of sd card (formatted to FAT32). Then flash as you described.
Click to expand...
Click to collapse
I tried to connect using usb cable, when I connect it on the bootloader screen the white stripe goes from "serial" to no text just white stripe. I ran the ROM downloaded from hTc site, but when it comes up with an connectioin error.
I am running Windows 7, I could not find a Windows Mobile Sync that's compatible with Windows 7. I tried the RUU_signed.nbh file, renamed to LEOIMG.nbh and copied to root of sd card - formatted to FAT32 but at first it updates then restarts after a minute. It says there's an error, it restarts again and continues with the update and everything says "ok" but when I restart it when the update is finished, still I have the bootload screen?
greyshade11 said:
I tried to connect using usb cable, when I connect it on the bootloader screen the white stripe goes from "serial" to no text just white stripe. I ran the ROM downloaded from hTc site, but when it comes up with an connectioin error.
I am running Windows 7, I could not find a Windows Mobile Sync that's compatible with Windows 7. I tried the RUU_signed.nbh file, renamed to LEOIMG.nbh and copied to root of sd card - formatted to FAT32 but at first it updates then restarts after a minute. It says there's an error, it restarts again and continues with the update and everything says "ok" but when I restart it when the update is finished, still I have the bootload screen?
Click to expand...
Click to collapse
Try moving your usb cable to a new port, preferably one at the rear of your pc ie with direct link rather than one at the front or a hub.
The sync software for Windows 7 is Windows Mobile Device Centre, but you won't be able to make a connection if you're in bootloader mode.
ClydeB1 said:
Try moving your usb cable to a new port, preferably one at the rear of your pc ie with direct link rather than one at the front or a hub.
The sync software for Windows 7 is Windows Mobile Device Centre, but you won't be able to make a connection if you're in bootloader mode.
Click to expand...
Click to collapse
I did what you said by inserting usb cable into a different usb port. It started installing the driver "QUALCOMM CDMA TECHNOLOGIES MSM" Now on the white stripe it says "USB".
So I ran both "RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship"
AND
"RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship"
But after about 8% it turns red and says error. On the phone it says "Upgrade ROM code error Please try again" on the green stripe.
greyshade11 said:
I did what you said by inserting usb cable into a different usb port. It started installing the driver "QUALCOMM CDMA TECHNOLOGIES MSM" Now on the white stripe it says "USB".
So I ran both "RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship"
AND
"RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship"
But after about 8% it turns red and says error. On the phone it says "Upgrade ROM code error Please try again" on the green stripe.
Click to expand...
Click to collapse
The stock ROM you used is the one you downloaded with your S/N?
kurt-willems said:
The stock ROM you used is the one you downloaded with your S/N?
Click to expand...
Click to collapse
Yes, this is correct. When I enter my S/N number in the hTc website it gives just the one option to download "ROM UPGRADE FOR HTC HD2". This is the ROM i'm using, I am correct in assuming this is my stock ROM?
greyshade11 said:
Yes, this is correct. When I enter my S/N number in the hTc website it gives just the one option to download "ROM UPGRADE FOR HTC HD2". This is the ROM i'm using, I am correct in assuming this is my stock ROM?
Click to expand...
Click to collapse
I can't see from distance what's going wrong, but based on the fact you have/use a correct stock ROM based on your S/N and you have try both installation possibilities (over ActiveSync and over SD-card) and both failed
I'm out of Idea for the moment.
kurt-willems said:
I can't see from distance what's going wrong, but based on the fact you have/use a correct stock ROM based on your S/N and you have try both installation possibilities (over ActiveSync and over SD-card) and both failed
I'm out of Idea for the moment.
Click to expand...
Click to collapse
I appreciate the help everyone has given me so far, thanks. Still I am having no luck getting it to load up to the windows mobile screen.
I bought this phone used, It came unlocked. When It was loading properly it appeared unbraded as there were no network carrier logos on start up screen. I am not sure if this phone is factory unlocked or was locked to a carrier.
Should I try the T-mobile ROM on it? Also I have been reading the treads trying to find a solution for the past 7 hours now LOL. I had read that this phone can run WP7 and Android.
Will i be able to get the phone working on any of those OS without having to put the WM6.5 stock ROM on it? Or do I need the stock rom for this phone to work to make the other OS to work?
greyshade11 said:
I appreciate the help everyone has given me so far, thanks. Still I am having no luck getting it to load up to the windows mobile screen.
I bought this phone used, It came unlocked. When It was loading properly it appeared unbraded as there were no network carrier logos on start up screen. I am not sure if this phone is factory unlocked or was locked to a carrier.
Should I try the T-mobile ROM on it? Also I have been reading the treads trying to find a solution for the past 7 hours now LOL. I had read that this phone can run WP7 and Android.
Will i be able to get the phone working on any of those OS without having to put the WM6.5 stock ROM on it? Or do I need the stock rom for this phone to work to make the other OS to work?
Click to expand...
Click to collapse
- your stock ROM version tels a lot. your device is factory unlok. and x.xx.405.x stock ROM are English stock ROM's
- No sir, don't install a T-Mous stock ROM, it aren't the same.
- Yes you can use/install Android or even WP7 on this device.
- but first of all we need to set it working again.
Ow, I just think about one thing. When you flashed over your SD-card witch SD-card dit you used? (size)
Most recommendation are the 2GB.
8GB and bigger gives some trouble.
kurt-willems said:
Ow, I just think about one thing. When you flashed over your SD-card witch SD-card dit you used? (size)
Most recommendation are the 2GB.
8GB and bigger gives some trouble.
Click to expand...
Click to collapse
I flashed the rom using 2gb micro sd card, which came with the phone. I also tried with a 4gb sd card, still same result - stuck on bootload.
Hello, I got the touch pro, which dont loading WM, bootloader but just right. As I have previously owned MDA Vario IV Since I've recorded through the official RUU ROM. Unfortunately, whatever I'm doing what I do on the phone boot up the WM. Tastes just turns me the bootloader does not need to even hold a button, it just simply connect to your PC or simply turn on. The RUU I wrote just empty words Current ROM. When I will continue, flash rom there, perform a restart and again I only bootloadri. Is it still possible to repair without service? Thanks.
Sorry for my english, only google translate.
much better you look this guide to flas rom ~ http://forum.xda-developers.com/showthread.php?t=508084
HARDSpl was made, I flash rom USB because it was not through SDCard.
Mathysko said:
HARDSpl was made, I flash rom USB because it was not through SDCard.
Click to expand...
Click to collapse
have you read and follow all instructions on the link that was my point ??
Ive opened this thread coz many people are finding my tutorial usefull
so here goes and if it helps let me know and give me a thanks
Hi i was new to all this and installed dynamics v2.0 fully unlocked rom the other day and this is how i went about it
download this
RUU_Mozart_Orange_UK_1.24.061.35_Radio_5.50.09.18_22.24.50.09U
http://www8.zippyshare.com/v/48117282/file.html
this is a load your phone back to 1.24
to install it i did this
turn phone off hold down volume down and turn phone on you should go to the bootloader screen then plug in your usb cable to the pc,
then on the white line at the bottom on phone screen should say usb instead of serial but maybe it will need to install some drivers cant remember 100%
when it is ready open that file and click the RomUpdateUtility.exe and follow the steps in that then you will have your phone back to 1.24
next you can follow this post here and download the attachment at the bottom named DFT_XSPL_WP7FG1.rar this what u need for this step
http://forum.xda-developers.com/showthread.php?t=1195647
basically this is the install procedure u may need to install active sync (XP) or windows mobile device center (vista and 7) but i did not have to my phone automatically did this
DFT_RSPL_WP7FG1_LAUNCH allows you to load RSPL on the device:
1. Extract ALL files from RAR archive.
2. Run DFT_RSPL_WP7FG1_LAUNCH (with administrative rights to access USB)
3. Mindfully reads information text. Press “Next” button.
4. Reset your device and hold “Volume Down” button during reset to enter OSPL mode.
5. Connect your device to PC via USB cable.
6. Now you may need to install proper USB drivers. They come with Active Sync / Windows Mobile Device Center.
7. Install drivers if required.
8. Make sure device show “USB” at the bottom instead of “Serial”.
9. Press “Next” button in the wizard. It should detect your phone.
10. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
11. After successful connection it should show device codename and allows to choose installed OSPL version.
12. You should look at the screen and select OSPL version in drop down list box. You need do this because it’s not possible to detect installed version via USB.
If your current SPL version doesn't present in the list, you can choose nearest version,
BUT ONLY IF IT HAS SAME FIRST NUMBER!!
Example: You have 4.XX on the device. Do NOT choose 1.XX 2.XX 3.XX.
13. Press “Next”. Wait until comes final page.
14. Read and close window
15. Look at the device – it must reboot to RSPL.
16. If you see RSPLX.Y.Z and “CotullaRSPL” on the screen – the task done! Otherwise, please report in this thread about your problems.
17. Put some feedback in this thread for community and developers.
Installing HSPL
DFT_HSPL_WP7FG1_INSTALL allows you to install HSPL on the device:
1. Launch RSPL on the device like described above.
2. Be sure that you close RSPL wizard window.
3. Run DFT_HSPL_WP7FG1_INSTALL.exe (with administrative rights to access USB)
4. Mindfully reads information text. Press “Next” button.
5. Proper drivers already must be installed in RSPL step.
6. Press “Next” button in the wizard. It should detect your phone.
7. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
8. After successful connection it should show device codename and allows to choose HSPL or OSPL version to install. OSPL means you install stock SPL back.
9. Check device codename, if something wrong turn off computer and run to the nearest forest. Grab some water with yourself.
10. Press “Next”. Wait until comes final page.
11. Device will reboot and start to boot OS.
12. Reset it and enter SPL mode again. Be sure there HSPLX.Y.Z and “CotullaHSPL” appear.
13. Put some feedback in this thread for community and developers.
Now u are ready
you can find what custom rom you want i used dynamics v2.0 which can be found here and its fully unlocked aswell so all i all im pleased with it
http://forum.xda-developers.com/showthread.php?t=1520352
download it and install the same way we installed the 1.24 rom in the begining of this post
turn phone off hold down volume down and turn phone on you should go to the bootloader screen then plug in your usb cable to the pc,
then on the white line at the bottom on phone screen should say usb instead of serial
when it is ready open that file and click the RomUpdateUtility.exe and follow the steps in that and then you will have loaded your desired custom rom onto your phone
I hope this helps some of u out and happy modding
best regards
steve
1.24
Great guide thanks, my phone is network unlocked do you know if that will revert once upgraded? also you mention rolling back to 1.24 what does 1.24 mean,and how do i find out if my device is on 1.24 already? one last Question how are you finding the rom any issues with it?
cheers
Geoff
geofferz said:
Great guide thanks, my phone is network unlocked do you know if that will revert once upgraded? also you mention rolling back to 1.24 what does 1.24 mean,and how do i find out if my device is on 1.24 already? one last Question how are you finding the rom any issues with it?
cheers
Geoff
Click to expand...
Click to collapse
1.24 im refering to the SPL you can find your version by turning the phone off holding volume down and power button and u will see your SPL at the top,
im not sure about the unlocked sim/network im new to all this aswell maybe do a search on the forums and see if you can find the answer, but i dont know this 1 sorry :/
rom is good no issues had a cable issue yesterday that wouldnt let me charge my phone but thats down to my dodgy cable
you dont have to install this rom you can use any custom rom you like or might find out there
anyways hope this helps
Launch RSPL
Thanks a great help.. ok to use to add tunes via zune? last bit on installing the custom Rom, what ruu option do I choose?
Cheers
hehe the first stage 1.2 spl.. when I open the rom update it gives a error 208? the update utility cannot open the requested file? any ideas and do i have to down to 1.2?
edit..Windows Mobile Device has been installed but when I open it, its not connected!! I powered of the phone with volume down. I can see the spl and usb at the bottom and it installed usb drivers etc, Im I missing a driver?
thanks once again
geofferz said:
hehe the first stage 1.2 spl.. when I open the rom update it gives a error 208? the update utility cannot open the requested file? any ideas and do i have to down to 1.2?
edit..Windows Mobile Device has been installed but when I open it, its not connected!! I powered of the phone with volume down. I can see the spl and usb at the bottom and it installed usb drivers etc, Im I missing a driver?
thanks once again
Click to expand...
Click to collapse
hi u don't need to worry about mobile device center this never picked up my phone either until I installed the custom rom
Don't ask why I've no idea
So what's happening when you press volume down and power you are seeing the multicolored bootloader screen right?
If so I don't know why the rom won't install for you
Maybe I've heard your firmware is at .707 if so you need y cables and its harder to downgrade your sol
tell me the firmware version please and ill try help u its in settings then about then advance on your phone if I remember
Oh also do not extract the 1.24 from the .rar file run everything from there
This is why ur getting that error I think
geofferz said:
Thanks a great help.. ok to use to add tunes via zune? last bit on installing the custom Rom, what ruu option do I choose?
Cheers
Click to expand...
Click to collapse
you dont need to select a option just load ROMUpdateUtility.exe
ive just downlaoded and reinstalled the rom myself to try see what u mean and i dont get this option
when you go to bootloader screen on your phone and it says usb open the rom file and click ROMUpdateUtility.exe
now dont open active sync or mobile tools as it says on the program information
just click the tick boxes and continue through the process
maybe try download the rom again found this
ERROR [208] : FILE OPEN
ERROR [210] : FILE READ
These error messages indicate that RUU lacks certain important files and cannot continue with the update. Please get the complete RUU package again.
but like i sed i have downloaded the file myself and it is working for me without any problems
beany2009 said:
hi u don't need to worry about mobile device center this never picked up my phone either until I installed the custom rom
Don't ask why I've no idea
So what's happening when you press volume down and power you are seeing the multicolored bootloader screen right?
If so I don't know why the rom won't install for you
Maybe I've heard your firmware is at .707 if so you need y cables and its harder to downgrade your sol
tell me the firmware version please and ill try help u its in settings then about then advance on your phone if I remember
Click to expand...
Click to collapse
Thanks for the help.
My firmware is 2250.21.40600.61,hope I don't need y cables for this version..
I see the multi coloured screen, and once plugged in to my pc it says usb at the bottom..
Strangely the 1.24 rom update works sometimes and not others, can you remember when you do done it, did it tell you want version currently on? because it didn't for me, I pressed next until update screen and was on 0% for bout 6-7 mins, my phone also displayed the same, how long did it take roughly
As regards to the Dynamics rom update.exe ( I opened with no phone attached ) It says welcome to the advanced rom update utility for Htc Mozart below that are, two ruu options.. regular (this is default) and below is custom I was thinking or using logic that I don't think i have hehe.. that the custom would be the option? or leave it
I really appreciate your help on this, I have installed many custom rom on android,but this windows phone grr annoying but I wont give up.
geofferz said:
Thanks for the help.
My firmware is 2250.21.40600.61,hope I don't need y cables for this version..
I see the multi coloured screen, and once plugged in to my pc it says usb at the bottom..
Strangely the 1.24 rom update works sometimes and not others, can you remember when you do done it, did it tell you want version currently on? because it didn't for me, I pressed next until update screen and was on 0% for bout 6-7 mins, my phone also displayed the same, how long did it take roughly
As regards to the Dynamics rom update.exe ( I opened with no phone attached ) It says welcome to the advanced rom update utility for Htc Mozart below that are, two ruu options.. regular (this is default) and below is custom I was thinking or using logic that I don't think i have hehe.. that the custom would be the option? or leave it
I really appreciate your help on this, I have installed many custom rom on android,but this windows phone grr annoying but I wont give up.
Click to expand...
Click to collapse
lol np mate ill try help as best i can
right i understand your bit now about the dynamics rom u need to select regular on this part
custom i think would be if u want to edit it or some **** but i have no idea so u use regular mate because this is the actual rom file made but remember u must downgrade and load rspl and hspl onto your phone before doing this step
right my firmware is 2250.21.51301.401 but i dont know if this changes on installation of the downgrade and adding the custom rom like i sed im a complete noob with this myself but all went smoothly for me thats why i made the tutorial
and no mate my phone took about 5-10 mins to install the 1.24 orange rom
have u tried a hard reset first and then see if it helps with the installation
ill search around for your firmware and see if there has been issues
edit..........................................
did a search on the forums and your firmware comes up with nothing :/ did a google and only shows this thread did you type the numbers correctly?
also you mean that the rom update works sometimes and not others?
if it works once it should install it mate np's
When you load you phone into bootloader the multicoloured screen can you please type here what u see mainly the top letters and numbers
beany2009 said:
When you load you phone into bootloader the multicoloured screen can you please type here what u see mainly the top letters and numbers
Click to expand...
Click to collapse
again thanks for your help
ok here goes red: PD 67100 ss-BC (4k)
SPL-4.6.2250.0(129193) mng
what you think?
i think my SPL was on that before so i dont know why u are having issues mate :/
maybe wait and see if a developer can read this and give us some info on why its not working for you :/
Thanx For The Help And the Tutorial It Was very Helpfull
Now my phone Is running dynamic 2.0
hey can u tell me what other custom roms are available that i can install on my phone and if there are any different methods of installing them
no problem mate glad it helped
erm the only other custom rom i have seen on mozart is deepdishing v7.0 you can find this in the development thread inside mozart topics
and for me mate im not sure and have not seen another way of installing another custom rom but im new to all this myself
anyway glad this helpped
regards
my computer wont pick up htc 7 mozart in bootloader
can anyone help me its doing my head in .
when you connect your phone to pc in bootloader its not showing as usb on the bottom of bootloader screen?
just serial?
just to confirm. this wont work on Asian handsets.
beany2009 said:
Ive opened this thread coz many people are finding my tutorial usefull
so here goes and if it helps let me know and give me a thanks
steve
Click to expand...
Click to collapse
Thx for the easy to follow guide.
It worked on a telstra brand mozart using windows 8.
Sent from my GT-N7105 using Tapatalk 2