Hi,
I have a Samsung galaxy Wi-Fi 5.0 16 GB model:YP-G70EW (I think it was this update G70XXKPH)
What did I do you ask?
Click settings-about-check for updates it found one clicked okay it started to download and finished the installation
and my device keeps on rebooting. I see the Samsung logo from 19 seconds,
what should I do?
Thanks in advance.
You probably need to wipe your data and cache partition. That can be done by booting into recovery mode (Home+Vol Up+Power).
Thanks for your fast response, but the (home+volume up+power) does nothing
(Power+volup) I selected -wipe cache partition- did not work, so I chose to -wipe data/factory reset- no help also anymore tips?
By the way, in the android system recovery<3e> window. I see something else weird, This is exactly what it says
– – Copying media files...
Successfully copied meida files.
#Manual mode#
– – Applying Multi-csc...
Successfully applied multi–CSC.
I know that my English is that good but do you see something weird here or is it just me?
Does it even get into android or does it just keep rebooting from the samsung logo?
I don't think so, it shows the Samsung logo for 19 seconds(19 sec every time)and reboots.
I can't even shut the device down. Try to contact Samsung support but no response yet it's been almost 24 hours.
PS. Can anybody give me some e-mail addresses for Samsung support you can PM if you want.
Thx.
Wh1tedev1l said:
I don't think so, it shows the Samsung logo for 19 seconds(19 sec every time)and reboots.
I can't even shut the device down. Try to contact Samsung support but no response yet it's been almost 24 hours.
PS. Can anybody give me some e-mail addresses for Samsung support you can PM if you want.
Thx.
Click to expand...
Click to collapse
If you hold the power button it should shut it down.
The shutdown button did work, only after 10 seconds holding down luckily the screen stays on for 19 sec.
Wh1tedev1l said:
The shutdown button did work, only after 10 seconds holding down luckily the screen stays on for 19 sec.
Click to expand...
Click to collapse
if you try flashing a kernel and rom meant for your device it should work again.. it sounds like something just got messed up with the flashing process (which does happen occasionally).
Sent from my SGP5
I have never done this how should I proceed?(Please give as much details as you can)
It probably involves a micro-SD, luckily i ordered one two hours ago, should arrive tomorrow morning.
Thx
Guide to flashing http://youtu.be/0imhKnMtQ9A
Hi guys,
well I just got an e-mail from samsung support that I should get it serviced to get the issue fixed(after 2 e-mails they answered back, well… It's something)
They send a link http://www.samsung.com/us/support/service/request,
so I choose option 1
model code: ?? YP-G70EW but I don't see my code on their site, what the hell should I do with this.
e-mail address: (at least I know this one.LOL)
I wonder if I should have gone through Samsung Belgium
address http://www.samsung.com/be/ another problem I can't even find this product their! Or model number
Could you guys give me some tips what to do.
And bit more information about my product
Samsung galaxy Wi-Fi 5.0 16GB (with the physical bottom) so the international one(right?)
model number: YP-G70EW
And which version of Oden versions should I use, and link please.
which kernel and rom should I use link also please.
damn, I'm demanding today
First: If you really want to flash a ROM, your guarantee expires.
The version with the physical Homebutton is the international.
You should always use the newest version of Odin.
Here is the link:
http:// www.google.com/url? sa=t&rct=j&q = & esrc=s&source=web&cd=2&sqi=2&ved=0CDwQFjAB&url=http%3A%2F%2Fforum.xda-developers.com%2Fattachment.php %3Fattachmentid%3D581913%26d%3D1304094576&ei=xGh0T-_ AEqGr0QXO1JX3Dw&usg=AFQjCNF7sF0f2yJp0IxHp1ISlP2fzGKhtw
And here the links to the Stock ROMs:
France: http:// www.sammobile.com/firmware/? Page=3&t=1&o=1&m=YP-G70&r=1 #
Italy: http:// www.sammobile.com/firmware/? Page=3&t=1&o=1&m=YP-G70&r=1 #
Sweden: http:// www.sammobile.com/firmware/? Page=3&t=1&o=1&m=YP-G70&r=1 #
I know that Belgium is not included in the list, but the ROMs should work with your device.
I've had the same exact issue as yours except I decided to fix it myself rather then check it in to be serviced.
I was a complete noob when doing it and I've managed to soft-brick my device during the process, but it was fun and I quickly learned to unbrick it and flashed a new stock ROM.
That was an awesome journey into Android I recommend to anyone (recommend; no responsibilities tho).
Anyway if you decide to take this path, beware that there are several versions of the Galaxy player 5.0 (US, Europe and others), you must verify that the ROM you're about to flash matches your device version, otherwise you'll eat ****.
Anyway checkout my post and its replies, I'm sure it will be valuable to you:
http://forum.xda-developers.com/showthread.php?t=1546068
Sent from my YP-G70 using XDA
I have a galaxy player 4.0 and it keeps rebooting and it's because I tried to install a custom boot logo. I can still go in download mode and Odin mode but does anyone know a custom bootloader I can install so I can access the files on my device because if I can delete the file I want to then it will work again.
Related
Hey,
I have a Samsung S2 (Korean Version) which was working fine. Since, it is being used by my younger brother for games etc. He informed me one day that the phone is not getting started. I checked the phone, switched it on and as it displayed Samsung SII logo and jumped straight away to recovery mode.
Resultantly, i installed AOKP rom using CWM recovery. The phone started and was working fine until restarted. On restart the phone again goes to recovery mode instead of loading the Rom.
Can anyone help me in fixing this ??
I refuse to help lazy people who insist on using such silly/generic topic titles like "Help Please" instead of using common sense and putting something relevant.
If you expect people to enter/read your topic and help instead of skipping or entering to leave remarks like mine I would recommend changing title to something useful for forum browsers.
Action Taken
TheATHEiST said:
I refuse to help lazy people who insist on using such silly/generic topic titles like "Help Please" instead of using common sense and putting something relevant.
If you expect people to enter/read your topic and help instead of skipping or entering to leave remarks like mine I would recommend changing title to something useful for forum browsers.
Click to expand...
Click to collapse
I have done as advised now if i may kindly be helped for fixing this issue
Reboot into Download mode,and flash stock ROM,then factory reset.I think you will can get into Download mode....just press the VOL DOWN+POWER+HOME buttons at the same time till it reboots.
Amm31c said:
Hey,
I have a Samsung S2 (Korean Version) which was working fine. Since, it is being used by my younger brother for games etc. He informed me one day that the phone is not getting started. I checked the phone, switched it on and as it displayed Samsung SII logo and jumped straight away to recovery mode.
Resultantly, i installed AOKP rom using CWM recovery. The phone started and was working fine until restarted. On restart the phone again goes to recovery mode instead of loading the Rom.
Can anyone help me in fixing this ??
Click to expand...
Click to collapse
did your rom could get into the operator interface after get in the CWM mode? if not ,try to install a new rom and back up your data,then wipe data cache and reinstall again. maybe your brother deleted some system files which make the system run regularly. therefore the phone jump to CWM when restart.
Samsung S2 korea version: Not booting
Folks.
I have a Samsung S2, from korea which is not booting up.
Unfortunately, when i try recovery mode.... it shows S2 screen and it gives me option in Korean language.
If anyone can help, it would be great.
May be I will need some language help as well.
I will post a picture of phone screen soon.
manitian said:
Folks.
I have a Samsung S2, from korea which is not booting up.
Unfortunately, when i try recovery mode.... it shows S2 screen and it gives me option in Korean language.
If anyone can help, it would be great.
May be I will need some language help as well.
I will post a picture of phone screen soon.
Click to expand...
Click to collapse
Dont worry, its not a big problem.
Press & hold POWER BUTTON + MENU BUTTON + VOLUME UP BUTTON for 5-10 seconds, then you will see something written in Korean language. Just ignore that and press VOLUME UP BUTTON. Then u will enter the boot menu. Use VOLUME KEYS to move up and down. and to SELECT something click on POWER BUTTON.
DO A BACKUP FIRST AND THE RESET UR PHONE.
i need help i tried to upgrade my software to 4.1.2 from 4.0.4
using a rom can it failed half way now i stuck in
a "bootloop" of odin download screen and help please
Rom was from
http://forum.xda-developers.com/showthread.php?t=2154790
My phone info
Samsung note 1 (SHV-E160L)
Adam1337 said:
i need help i tried to upgrade my software to 4.1.2 from 4.0.4
using a rom can it failed half way now i stuck in
a "bootloop" of odin download screen and help please
Rom was from
http://forum.xda-developers.com/showthread.php?t=2154790
My phone info
Samsung note 1 (SHV-E160L)
Click to expand...
Click to collapse
I do not have the Korean model, but understand your present moment of craziness. I am sorry if I may not b able to provide you with actual technical support. however, if you find someone that can help here, they might need a bit more information. I have looked at the thread and wow, flashing is a bit more involved with you model.
don't get offended when I ask you some very basic questions here, many times it is something so simple and was simply overlooked. I thought that I had read somewhere else that the screen you posted was an alternate download mode screen. I always make extra preparations when I need to Odin anything.
did you read OP ? (I know, but I read several times) I read some of it and it seems as if you are not the only one to have similar problem.
did you et ALL the files you needed ? do you know where they are ?
were there any tutorals on Youtube ? they helped me
did you actually rehearse ? silly, I know. walk though everything in your head an compare to thread / youtube.
I hope somebody else will come around offer some more help, sometimes when someone brings up the most basic things, it triggers switch, and you realize what went wrong.
I hope this does that for you, good luck
Its there a way to reboot normally or its it broken i have read it a lot and prepared everything when i tried it fail i'm not sure how to restore it because when i try plug it in to my computer it doesn't come up only on Odin i tried kies did not find my phone so yeah oh and i tried to reboot in to recovery mode didn't work so i'm kina stuck and as far as i know it could be in a bootloop or somthing.
Many thanks,
Adam
Is download mode boot looping? If so it sounds like a stuck power button. Try tapping the power button rapidly and see if it stops looping.
Odin won't recognize a looping device. Neither will kies. Once you stop looping flash files again.
440bro said:
Is download mode boot looping? If so it sounds like a stuck power button. Try tapping the power button rapidly and see if it stops looping.
Odin won't recognize a looping device. Neither will kies. Once you stop looping flash files again.
Click to expand...
Click to collapse
i've try tapping the power button rapidly nothing happened
Phone name : Samsung note 1 korean version
on the phone it saids :
ODIN MODE
Product name: SHV-E160L
Custom Binary download : No
Current Binary : samsung Official
(The photo) Real one is in korean same meaning
Adam1337 said:
i've try tapping the power button rapidly nothing happened
Phone name : Samsung note 1 korean version
on the phone it saids :
ODIN MODE
Product name: SHV-E160L
Custom Binary download : No
Current Binary : samsung Official
(The photo) Real one is in korean same meaning
Click to expand...
Click to collapse
can you pull battery and get into download mode?
captemo said:
can you pull battery and get into download mode?
Click to expand...
Click to collapse
Ok i'll made a video , will be uploaded soon
www *dot* youtube *dot* com/watch?v=JWr67N122r8&feature=youtu.be
By the way i'm using Odin v 3.07 do i need to use a lower version?
It can't hurt trying version 1.85
Adam1337 said:
Ok i'll made a video , will be uploaded soon
www *dot* youtube *dot* com/watch?v=JWr67N122r8&feature=youtu.be
By the way i'm using Odin v 3.07 do i need to use a lower version?
Click to expand...
Click to collapse
may I suggest posting under the general forum here, there is a sub forum for your device there which may give you some more target specific technical help.
just go back out from here and up t the general section. it might be about 5 or 6 threads down. there may be more people there with same device with a post as recent as yesterday.
good luck and keep us posted here. you are getting some reaction from your phone so I am sure it is not bricked.
440bro said:
It can't hurt trying version 1.85
Click to expand...
Click to collapse
Tried it didn't work as well lol
Uploading....Coming soon
Hello everyone this is the official odin package for the galaxy mega ATT version. With this you can get your phone back working if you get the "This phone is not running authorized software crap. " etc . Also hope it encourages more people to find a root method without the fear of having a brick. As many of you know this package was nowhere to be found so I had to bribe a Samsung employee to give it to me which means it wasn't free for me but I'm sharing it with you guys so if you send me a beer my way i'll be happy not mandatory.
This package is in multiple parts:
I527UCUBNE7
AP: Must be flashed under PDA in Odin. This is the biggest file and contains your system,recovery and kernel partition Download
BL: This is the bootloader. If you already took the update ignore this but if you want to upgrade your phone you must flash this Download
CP: This is the modem and other network related partitions. You must flash this under Phone in odin Download
CSC: This contains carrier related settings for our firmare. Flash this under CSC in odin. Download
Highly Recommended to perform a factory reset after the flashing is completed. Let me know your results
Omg !! Super thanks bro !!!! =))))))))
So good !!!!! update successfully
Thanks again !!!
so the guys that have tried this can confirm that is working!
and also liked to know how root is being dealt with
latinohot said:
so the guys that have tried this can confirm that is working!
and also liked to know how root is being dealt with
Click to expand...
Click to collapse
Garack has been working on it and has actually posted a file to flash in Odin I beleive. He say that if it boots up, then root should be obtainable.
Not sure anyone has tried it yet.
It is in the "root bounty for 4.4.2 update" thread
Sent from my SAMSUNG-SGH-I527 using XDA Free mobile app
im getting error last stage on system upload any advised ?
@ Sunderwear Thank you very much for the great post and instructions. I'm currently testing it out with my i527 AT&T with ODIN 3.09... will post results in a few minutes. My phone was stuck in reboot after official 4.4.2 AT&T update left it in loop mode... give me a few minuytes and I'll post my results!
Too close. I did all the steps, and indeed it passed all Odin steps (picture), but it's still stuck in loop mode. When I try to go into Recovery mode (Vol + and HOME), it will only show the blue letters on top of the screen (picture), then it reboots on its own... no fix do you know a possible fix for loop mode.
If I go to Odin mode (Vol - and HOME), this is what I got (picture)...
alex852 said:
Too close. I did all the steps, and indeed it passed all Odin steps (picture), but it's still stuck in loop mode. When I try to go into Recovery mode (Vol + and HOME), it will only show the blue letters on top of the screen (picture), then it reboots on its own... no fix do you know a possible fix for loop mode.
If I go to Odin mode (Vol - and HOME), this is what I got (picture)...
Click to expand...
Click to collapse
Has your phone been repaired.. Like a broken screen recently? And if it fails with the red letters at system upload. M. Try again with a different USB cord or port. I own a cellphone repair shop and have been using the files with no problems
Sunderwear said:
Has your phone been repaired.. Like a broken screen recently? And if it fails with the red letters at system upload. M. Try again with a different USB cord or port. I own a cellphone repair shop and have been using the files with no problems
Click to expand...
Click to collapse
Yeah, the screen was replaced a while ago. The phone went bad once it installed the 4.4.2 official update. I will try use some other usb cable. I have plenty of microusb wires. Do you think the screen has something to do with it?
Sunderwear said:
Has your phone been repaired.. Like a broken screen recently? And if it fails with the red letters at system upload. M. Try again with a different USB cord or port. I own a cellphone repair shop and have been using the files with no problems
Click to expand...
Click to collapse
Ok, I used a different port using also a brand new official/original Samsung MicroUSB cable to retest it. :crying: no work, again stuck in loop mode. Tomorrow, I will get another computer to retest this with another one. Will post the results tomorrow.
When the phone loops, I do not have any letters that appear anywhere besides the Samsung Galaxy Mega logo. it just vibrates, and then it restarts without showing any messages/letters.
You mentioned "Red letters at System Upload" is that when I hold Vol - and home? because I only get the blue letters if I do the Vol+ and home.
Thank you for your patience man. I'm sort of a noob, well, not sort of!
I haven't tried this yet...but I will back up tomorrow and report back how it goes with my unit...I still have my factory with no knox bootloader so far..and was debating if I want to even try really...
alex852 said:
Ok, I used a different port using also a brand new official/original Samsung MicroUSB cable to retest it. :crying: no work, again stuck in loop mode. Tomorrow, I will get another computer to retest this with another one. Will post the results tomorrow.
When the phone loops, I do not have any letters that appear anywhere besides the Samsung Galaxy Mega logo. it just vibrates, and then it restarts without showing any messages/letters.
You mentioned "Red letters at System Upload" is that when I hold Vol - and home? because I only get the blue letters if I do the Vol+ and home.
Thank you for your patience man. I'm sort of a noob, well, not sort of!
Click to expand...
Click to collapse
No worries. I was asking because the same happened to me with a customers phone..got screen replaced..then he took the 4.4.2 ota update..got stuck at samsung logo bootloop..i loaded the firmware like 4 times..re partition with pit file and erase all nand...I would get stuck in the same screen saying entering recovery..So it's an issue going around. Last resort would be sending it to Samsung
Sunderwear said:
No worries. I was asking because the same happened to me with a customers phone..got screen replaced..then he took the 4.4.2 ota update..got stuck at samsung logo bootloop..i loaded the firmware like 4 times..re partition with pit file and erase all nand...I would get stuck in the same screen saying entering recovery..So it's an issue going around. Last resort would be sending it to Samsung
Click to expand...
Click to collapse
Yes Sunderwear that will happen because there is 3rd parties making aftermarket screens and people were buying them as replacements...If you don't have the OEM screen the driver in the firmware won't work and it will hang...I run in to something like this on a Galaxy S4 I repaired...
alex852 said:
Too close. I did all the steps, and indeed it passed all Odin steps (picture), but it's still stuck in loop mode. When I try to go into Recovery mode (Vol + and HOME), it will only show the blue letters on top of the screen (picture), then it reboots on its own... no fix do you know a possible fix for loop mode.
If I go to Odin mode (Vol - and HOME), this is what I got (picture)...
Click to expand...
Click to collapse
check your AP files size that was happen to me i download file wan;st complete than i download again and make sure file download complete
and after that use odin don;t need other file just select on PDA and let odin run after that every thing will bee fine
I ran it as instructed and it worked flawlessly. tHANKS [email protected]
Help!
Every time I try to use the PDA and PHONE files, it says they have an invalid md5 hash. I've tried re-downloading them, but to no avail. Could anyone help with this?
thanks.it works fine...
I did all the stepa and finally I have K.K. Just wanted to say- thank you.
USMAN_ZEESHAN said:
check your AP files size that was happen to me i download file wan;st complete than i download again and make sure file download complete
and after that use odin don;t need other file just select on PDA and let odin run after that every thing will bee fine
Click to expand...
Click to collapse
Sorry for the long delay. I think I found the full issue with the Samsung Glaxy Mega boot loop on 4.4.2
My phone is till not working. We own four 6.3 Megas (1 my wife, 1 daughter, 1 son, and mine).
Officially I have 2 that are not working properly and stuck on boot loop. My wife and daughter are working properly on 4.4.2 my son's now and mine are stuck in boot loop. Wife's phone has original screen and it's working properly, my daughter has a replacement screen I bought on ebay for about $160.00 on January. My son's I've replaced the screens about 3-5 times already (a ton of money wasted), and mine, recently I did replaced it on May (before the 4.4.2 update on June). Here goes the issue:
My son's phone updated today about 2 hours ago while we were visiting the AT&T store for U-Verse Quote. Did not know it updated until we got home... Sons' phone is stuck in boot loop also now!!!!!!!!!!!! What I did was I took my daughters phone apart (with expensive replacement screen and currently running 4.4.2), and installed the screen on my sons and then mine, and each phone would work flawlessly with that screen, so I took the current replacement screens I had from my phone and my son to install them on my daughter's and each one would go into boot loop.
After that, I re installed the good screen on my daughters back, and daughters work properly again. I guess the generic OEM screens from eBay I've been buying for $50 bucks are not compatible with 4.4.2 Kitkat, they are only compatible with 4.2.2 Jelly bean.
Anyone knows where I can buy original screens? I've contacted several sellers on eBay to see if the screens work on 4.4.2 because I don't want to spend more money on screens. I just got 1 from China 2 days ago, and that one also gets stuck in boot loop... so frustrated with screens. All my OT from work goes to pay for these issues... Help anyone? Anyone sells working 4.4.2 compatible screens?
Also, I will buy a broken ORIGINAL screens from ebay (like $7-$10) to test it out and verify. I will post results. Hope this experiment (and my sadness) will help you guys out if stuck in boot loop.
P.S. Oh yeah, I did do both phones on PDA, then all BL,PDA, etc... and I still get boot looped. I have to say THANK YOU to the original autheor because it does work! It's just my screens that doesn't work!!!!! HELP GUYS!!!!!:crying:
Is there a certian order u need to flash these in?
Any short tutorials..
Ive flashed odin pda only b4..
Have to factory reset first?
Thanks guys.
Hello,
I've purchased a Galaxy Tab S6 (SM-T865N) International version, mainly to use it with with 4G in US on Xfinity Mobile. I received the tablet, inserted the SIM card and it was working 'relatively' on the network. Every now & then I would get a message 'failed to register to network', but for the most part, mobile data is working.
Since it is a Korea version, certain things don't work. Nothing major, but I would like to make it perfect. Certain User update posts in the Galaxy store display in Korean Language, and the weather app is slightly limited, with the error 'not available outside of Korea'.
I did some searching and found other firmware available for this exact model on Sammobile. My country (US) is not supported, but I would like to try the UK firmware, if nothing else, to fix some of the language issues. I downloaded the UK firmware package and Odin (3.13 & 3.14.1). I installed the Samsung drivers. I booted the tablet into recovery by holding 'power & volume up' then connected it to the computer. Odin WILL NOT found the tablet. I rebooted into the normal OS and connected it and Odin then found it, but obviously that doesn't work. I can not get Odin to connect while in recovery.
Does anyone have suggestions on what might be happening?
And maybe all this effort isn't worth it either, hard telling whether it'll work better or worse with the UK firmware on it. Any tips?
It's been several years since I did this sort of thing, so I'm a little rusty. I thought this would be a simple procedure.
it sounds to me like you are not putting it into download / Odin mode, but I could be wrong. I haven't tried to use Odin on this tablet yet, but was actually about to do this same thing as well, as my device has an origin CSC of singapore, and hasn't had an official update in almost 2 months, so I was going to flash the UK version as well.
---------- Post added at 07:58 PM ---------- Previous post was at 07:51 PM ----------
So I just tested it on my tablet, here is what you need to do:
Power off the device
Press and hold the Volume up button and then press and hold the power button
When you see the initial boot screen, release the power button, but keep holding volume button
When you get to the recovery screen, you need to use the volume up / down buttons to highlight the option that has "bootloader" in the title, and press the power button to select it.
Then you should see a screen that says "Download" or something like that.
Plug in USB, and Odin should see the device.
Yeah, you're booting into recovery, you need to boot into Download mode - Hold both volume up and down whilst inserting the USB-C cable to enter Download mode.
Your correct
bartleby999 said:
Yeah, you're booting into recovery, you need to boot into Download mode - Hold both volume up and down whilst inserting the USB-C cable to enter Download mode.
Click to expand...
Click to collapse
Your Correct. Device needs to be plugged into the pc for it to boot to the screen that shows all the info. I wonder why they made this a requirement. Its very unintuitive. I also didn't see it documented anywhere. How did you find out about this ? Thanks again for the help!
naruto.ninjakid said:
Your Correct. Device needs to be plugged into the pc for it to boot to the screen that shows all the info. I wonder why they made this a requirement. Its very unintuitive. I also didn't see it documented anywhere. How did you find out about this ? Thanks again for the help!
Click to expand...
Click to collapse
You wouldn't happen to have that firmwire file handy / a way to share it online would you? Sammobile's free download server is down right now, and I was going to try to flash it this weekend.
naruto.ninjakid said:
Your Correct. Device needs to be plugged into the pc for it to boot to the screen that shows all the info. I wonder why they made this a requirement. Its very unintuitive. I also didn't see it documented anywhere. How did you find out about this ? Thanks again for the help!
Click to expand...
Click to collapse
I did a lot of reading before I rooted this Tab and that piece of Info came from This thread.
fallingup said:
You wouldn't happen to have that firmwire file handy / a way to share it online would you? Sammobile's free download server is down right now, and I was going to try to flash it this weekend.
Click to expand...
Click to collapse
Sorry, I dont. I meant to make that post in another thread. I have not flashed anything on my device yet.
I have the same Korean model SM-T865N 4G LTE version with the latest firmware.
Can I flash it using Odin with the latest frimware for UAE?
I mean the one with CSC code XSG (XSG - United Arab Em)
AP VERSION T865XXU2BTC7
CSC VERSION T865OJM2BTC7
Besides i have another issue with my speakers as they are not working for some reason? I tried reset both soft and hard without luck. It always get stuck on rebooting many times but after many times i got it to reboot BUT i can only have sound from bluetooth headphones!!
buafnan said:
I have the same Korean model SM-T865N 4G LTE version with the latest firmware.
Can I flash it using Odin with the latest frimware for UAE?
I mean the one with CSC code XSG (XSG - United Arab Em)
AP VERSION T865XXU2BTC7
CSC VERSION T865OJM2BTC7
Besides i have another issue with my speakers as they are not working for some reason? I tried reset both soft and hard without luck. It always get stuck on rebooting many times but after many times i got it to reboot BUT i can only have sound from bluetooth headphones!!
Click to expand...
Click to collapse
Did you able to flash that firmware on your tablet?
IF you mean did I succeed in flashing it through Odin then yes BUT unfortunately I couldn't get it to reboot correctly & it takes a lot of time trying to reboot but still no luck. So, I took it to a repair shop & they told me it needs new motherboard !! How can this be even possible IF I still can get it to connect to Odin and download the firmware successfully BUT no luck in getting it to reboot correctly!!
buafnan said:
IF you mean did I succeed in flashing it through Odin then yes BUT unfortunately I couldn't get it to reboot correctly & it takes a lot of time trying to reboot but still no luck. So, I took it to a repair shop & they told me it needs new motherboard !! How can this be even possible IF I still can get it to connect to Odin and download the firmware successfully BUT no luck in getting it to reboot correctly!!
Click to expand...
Click to collapse
Have you tried reflashing the old firmware of your country? Weird that its not working.
I did try that and managed to flash it successfully to the old firmware using Odin but unfortunately I still couldn't get it past a full reboot as it got stuck after a long time and it takes me to the Android System Recovery screen wherein also tried to 'wipe cache partition.’ and try reboot again but I still end up with the recovery screen!
buafnan said:
I did try that and managed to flash it successfully to the old firmware using Odin but unfortunately I still couldn't get it past a full reboot as it got stuck after a long time and it takes me to the Android System Recovery screen wherein also tried to 'wipe cache partition.’ and try reboot again but I still end up with the recovery screen!
Click to expand...
Click to collapse
Can't you put in a warranty claim ? Here where i am based i had a new battery, and new screen installed from samsung! this was a Galaxy S8+ was well over 2 years old they did it for free! New screen and new battery! My Note 9 is going this monday for a new battery my Tab S6 works flawlessly so don't need to send that in! but i'm sure if you ring up Samsung they will replace the motherboard for free as it's not even 12 months old!
hi there,
hope someone can help me,
in my samsung tab s3 sm-t820 i installed twrp_3.2.1-1_T820_28518 and lineage-17.1-20201227-UNOFFICIAL-gts210wifi
but when i reboot i am with the boot screen in loop
i've already tried to wipe and reinstall. but nothing.
please let me know i have a chance.
thanks
someone?
Lucauonz said:
someone?
Click to expand...
Click to collapse
Hey
Lucauonz
maybe you have not the right Lineage-Release ... use lineage-17.1-20200211-UNOFFICIAL-gts3lwifi.zip https://drive.google.com/file/d/1D8lY5z9O3oafqiWlDLvtltFDQCEHnZbN/view?usp=sharing
from this thread: https://forum.xda-developers.com/t/...l-lineage-17-1-android-10-q-20200211.3981535/
I wish you success
Edit: At the end of the discussion there is a link to https://drive.google.com/drive/folders/1E5pBRVSkHv-nc9pQ25DtAp4MwfOOgIwy with lineage-17.1-20200829-UNOFFICIAL-gts3lwifi.zip
Frischifrisch said:
Hey
Lucauonz
maybe you have not the right Lineage-Release ... use lineage-17.1-20200211-UNOFFICIAL-gts3lwifi.zip https://drive.google.com/file/d/1D8lY5z9O3oafqiWlDLvtltFDQCEHnZbN/view?usp=sharing
from this thread: https://forum.xda-developers.com/t/...l-lineage-17-1-android-10-q-20200211.3981535/
I wish you success
Edit: At the end of the discussion there is a link to https://drive.google.com/drive/folders/1E5pBRVSkHv-nc9pQ25DtAp4MwfOOgIwy with lineage-17.1-20200829-UNOFFICIAL-gts3lwifi.zip
Click to expand...
Click to collapse
Hi, thank you anyway but i had some error while i tryied to flash rom and gapp as you can see in the attached screeshot:
sorry, I repeated the installation a second time but this time without any kind of error, now I have restarted the system to get it started, I am with the boot screen in loop, I have read that at the first start it takes some time, for now I wait.
he boot screen is in loop for almost an hour, now the istallation was clear,
I have done these steps in sequence:
format and reboot recovery
flash ROM and GAPPS
reboot - system
boot screen is in loop
any advice?
thanks a lot
Sure ... How well do you already know about rooting or the tools for Samsumg devices?
I will sketch a brief instruction, first download:
Odin (https://forum.xda-developers.com/t/...ead-03-sep-20-galaxy-s10-sm-g975f-ds.3908710/ should work ... you can find most of the software in the tools section odf xda)
SamFirm (https://forum.xda-developers.com/t/tool-samfirm-samsung-firmware-downloader-checker.2988647/)
Use SamFirm to download the latest original Samsung Firmware.
(Connect Tablet with PC & start Download-Mode: press Power (only until Vibrate) + Volume down + Home green Screen then Volume Up, voila)
And use Odin to flash Tablet S3 -> good as new, and you can start all over again ;-)
I will attach some Screenshots ...
Many Greetings
STOP
Did you (not forget to) FORMAT DATA before your attempt to Install a Rom???
maybe try to flash https://forum.xda-developers.com/t/rom-sm-t820-tweaked-rom-sm-t820-tweaked.3659433/ first ... in the thread are very detailed instructions.
just to clarify the above, this is done wile in twrp > wipe menu >format data and it requires you type"yes" before it launches the process
@Frischifrisch @Lucauonz
As Samsung has changed servers or what so ever, Samfirm I didn't find working any longer.
Samfirm_reborn did/does it.
GitHub - ivanmeler/SamFirm_Reborn
Contribute to ivanmeler/SamFirm_Reborn development by creating an account on GitHub.
github.com
.
Btw. recommendation of "Format Data" I encourage as well.
Might be neccessary to reboot to recovery afterwards before continuing.
@Lucauonz Which Gapps are you using?
Pico version I've always found best, as everything else can be installed later additionally.
Try just flashing ROM and test if device restarts without anything else to exclude Gapps as the cause for the failure.
Hi guys,
thanks a lot for your help, for now i am still with this problem, i am left with the boot screen in loop,
now i'm looking for a way to go back to an original android version if possible, a version that doesn't slow me down.
i don't know if it's possible not having a backup
thanks verymuch
Luca
Lucauonz said:
Hi guys,
thanks a lot for your help, for now i am still with this problem, i am left with the boot screen in loop,
now i'm looking for a way to go back to an original android version if possible, a version that doesn't slow me down.
i don't know if it's possible not having a backup
thanks verymuch
Luca
Click to expand...
Click to collapse
That's not a problem to go back to stock.
Just follow the post from @Frischifrisch and use samfirm_reborn to get multiple part version.