First off I'd to say hello from Alaska,
Ok this may sound strange but does anybody out there know where i might find or have one made, I'm looking for a cable with 2 40 pin connectors on both ends, 1 male and the other female. This is for my TF201 and dock, I would use it so I don't have to take off the case to the Prime just plug in to the prime and to the dock..
Thank you all Stan
Cables to Go should be able to do this for you. I've had them make custom cables for me before. It likely won't be cheap, but they should be able to do it.
www.cablestogo.com
Just in case anyone was curious, I thought I would try to get lucky and see if a female-female USB adapter with a standard ASUS 40-pin cable on either end would work. However, it was only a novel attempt and the tablet does not recognize the dock as I had hoped.
I am sure Cables-to-Go could get something to work, but I agree that it will be quite expensive. It would be nice if there was a jumper cable accessory to accomplish this same concept since I am in the same position as the OP and typically carry the tablet in its own case and only use the dock when I have alot of typing to do.
On a side note, I did confirm that my Logitech Anywhere Mouse with the Unifying Receiver does work 100% with my tablet and Dock!....I just may be able to leave the laptop at the office yet!
Does anyone have a mapping of the pins and wires? I would like to try and "splice" two cables together to try and make a jumper cable but would need to make sure that I make the right connections. Any assistance would be greatly appreciated.
I don't think that's going to work for several reasons.
First and foremost, if use two TP USB cables as the souce of the parts, you'll end up with a "jumper" cable with male connectors at both ends. You need male to female, remember?
Secondarily (and almost as important) is the number of contacts on the USB end of the cable. USB has four conductors plus shield and nine conductors plus shield in USB 3. Taking a cursory glance at USB plug on my TP cable, that's all there is. I don't see any additional conductors.
Following this, it's EXCEEDINGLY unlikely that the cable has 40 wires (one for each pin on the Prime end) running the full length. If it did, where would they connect to on the USB plug? Kinda silly to include extra copper to go nowhere.
Instead, if you were to pry open the 40 pin male plug, you'll see that most the pins aren't connected to anything. They're not needed for the USB cable.
Sorry to say, this just isn't going to work.
If you do choose to clip one of your cables just to have a look-see, cut the cable somewhere in the middle. If you cut right up next to the USB plug, you won't have ample wire there to repair what you're about to break.
I am aware that you will need a female adapter to make a true "jumper" cable. However, there may be a way of jerry-rigging a connection to the dock if a female connector can't be found (I have yet to find a part online).
My question is more in regards to whether or not anyone had a schematic of which of the pins are connected to which of the respective USB pins so that I could determine the best way of making a connection....short of having a cable for the ASUS TF201 like this: iPhone Extension Cable
Related
Trying to find out if there is such a thing as going from extmicro usb that the evo and flyer have to a usb type A (or any other normal usb).
Need a right angle to plug into tablet for car install and found that I can fit a microb angled cable into the tablet, but now need to take the car charges extusb and get an adapter to hook it all together.
You can just buy a regular micro USB extended cable. It fits in the flyer/view charge port.
Proprietary cable is the one on the right. Regular micro USB on left.
I am installing the tablet in dash of a car.
I have the oem car charger because its only one with right voltage. But I need a angled usb for clearance issues. So im trying to figure a way to go from the charger EXTMICRO usb to the angled usb.
Searched around and have come up completely empty.
I'm working on the same project and found this thread searching (again) for more info on extusb. The solution I came up with for getting enough clearance to use the port requires disassembly and if you plan on keeping the warranty, it's probably not a good option for you.
Anyway, my solution was to make some small right-angle brackets for the pcb that contains the extusb port. It requires material for the angle brackets and two small screws with nuts. See attached for a better idea.
I actually got the tablet installed and fairly well, but have since removed it to come up with better designs for charging, access to the power button (and possibly volume buttons) for recovery actions, turning the screen on/off with ignition, and potentially microphone relocation.
You may want to check out http://www.dealextreme.com/ for right-angle and other adapters if you don't want to open up the tablet.
PS: Protect that screen. The plastic is very soft and will easily scratch.
I don't follow.
I thought the HTC car charger was a plug with a USB port in it just like all the others. I thought this might help, but I probably have no idea what you're really looking for
http://www.amazon.com/Cables-Go-Right-Angled-Micro/dp/B005EV2LAM
If you *need* to use the 12pin micro usb that the view has (which from my understanding was only there for the docking station utility), then you might be out of luck unless you can build something yourself.
Im looking for a cable like you linked to, but then I need a way to connect the flyers car charger special usb tip into it. Only way I can think of is to carefully grind the corners so that it will fit into a micro B female connection.
But the chargers are not cheap and if I F*** it up Im out $30
On a kia soul forum where others are planning on doing the same install with the flyer, one guy has come accross a company that makes custom cables. He said that if We send the car charger to them they will replace the usb tip with a micro B 90 degree angle for $25.
So A person is sending the charger to them to have it done and is going to let us know how it comes out.
jacobbones, can you provide a link to the kia soul flyer thread?
Yes, here it is.
http://www.soulhamsters.com/forum/i...ale-again-24feb-7-android-tablet-199-shipped/
Talk about the custom job is near the end of the posts
opening up the car charger and replacing the cable is incredibly simple. I have done it so many times, I can probably do it blindfolded. I actually had to go and replace the OEM chargers cable with the USB cable that it came with because my damn dog chewed threw the charger cable. Didn't come back very pretty, but it works, that charger has got the be the best charger built I have ever seen, incredibly difficult to open, but I'm sure the car charger is a lot easier to open, you just need a soldering gun and it should be easy.
Sent from my ADR6425LVW using xda premium
I have a MHL Adapter and I get video just fine. Now I want to be able to sit on my couch while i use the adapter. Seems to me the simplest way would be to use a 15-20 foot Micro USB Male - Micro USB Female extension cable.
Does anyone have any experience with such a setup? Do you have a recommendation for such a cable?
TIA!!
Why micro USB? You can get a HDMI cable as long as you might want (Monoprice is particularly good). If it's not enough you can carry a HDMI signal over a single or (simpler to find) two CAT5 cables w/ RJ45 jacks for hundreds of feet.
I guess the thought was that if I have the Micro USB Extension, then it's one thin lightweight wire that has to travel across the floor.
If I did HDMI, I'd still have to be near power whereas with Micro USB, I could set the power adapter, and HDMI, and MHL Adapter all together and then have a thin and lightweight wire traveling across the floor.
But if it's not possible, (micro USB limitiation??) then HDMI it would have to be.
bean1975 said:
Why micro USB? You can get a HDMI cable as long as you might want (Monoprice is particularly good). If it's not enough you can carry a HDMI signal over a single or (simpler to find) two CAT5 cables w/ RJ45 jacks for hundreds of feet.
Click to expand...
Click to collapse
If the micro USB works it would be much cheaper than a comparable length hdmi cord.
Sent from my SAMSUNG-SGH-I717 using Tapatalk
I would test http://www.amazon.com/Extender-over-CAT5E-CAT6-connection/dp/B003L14ZTC this. It's hard to get cheaper than cat5e.
Just bought 10 feet on amazon! Lovely!
Sent from my SAMSUNG-SGH-I717 using Tapatalk
I wanted to do exactly this - extend the cable but at the micro-USB end to avoid having the Micro-usb power supply line and the bulky MHL adaptor all where the phone is - much cleaner to just have a thin cable coming out of the phone and headed towards the TV.
I did get hold of a micro-USB extension cable (2m/6ft) but unfortunately it does not work. Directly plugging the phone into the MHL adaptor works perfectly, as soon as I insert the micro-USB extension it doesn't work. I need to have a closer look to check the pins are populated etc, but not sure why this would be an issue - don't think it can be signal strength and if all the pins are populated I don't see why the adaptor would care.????
Any thoughts?
Micro B USB extension not working
I, too have been trying to figure out why an extension cable doesn't work the way you think it might. Today, I tried cutting my 6 foot cable, first making sure I had the right power leads working. Then I went through all the possible combinations of connections to see if one would work. None do. I'm at a complete loss on this wondering what I should try next.
Thanks for info....similarly baffled but at least you have ruled out something!
Like the other guy said, get your x for of hdmi cable, then just plug your AC charger in where you are. Mhl might use additional connectors/pins/whatever vs micro USB. Or you can go totally wireless and use a Bluetooth mouse and keyboard.
Also I remember I had a charging issue with an extension. Sometimes one product works better than others. I can't charge my phone with my 20 dollar AC charger from best buy since the ICS leak. It's weird. Hdmi cables are pretty uniform, I would just extend that.
Sent from my SAMSUNG-SGH-I717 using XDA
Yes, that works, always has, but that's not the point. Would rather have just one long cable connected to the phone in front of the TV rather than three cables, the device and the phone in a kludge setup.
A partial answer
This allows connecting 6 feet away with a thin, flexible single cable..Also cheap, but shipping takes 15 days.
goo.gl/NzCik
Gavdroid said:
I did get hold of a micro-USB extension cable (2m/6ft) but unfortunately it does not work. Directly plugging the phone into the MHL adaptor works perfectly, as soon as I insert the micro-USB extension it doesn't work. I need to have a closer look to check the pins are populated etc, but not sure why this would be an issue - don't think it can be signal strength and if all the pins are populated I don't see why the adaptor would care.????
Any thoughts?
Click to expand...
Click to collapse
I took apart the two cables and the USB has four wires while the MHL cable has ten.
are the mhl wires easily extendable themselves by splicing? I'm thinking strip out a few usb cables and use the wires? Or just go purchase some extremely thin gauge wire (22 gauge) and make it yourself?
Micro B USB extension not working
The Micro B USB connector only has 5 connections, so there is no way you can connect 10 from the MHL cable to it, so something else is going on.
pinoutsguide.com/PortableDevices/micro_usb_pinout.shtml
amblix said:
are the mhl wires easily extendable themselves by splicing? I'm thinking strip out a few usb cables and use the wires? Or just go purchase some extremely thin gauge wire (22 gauge) and make it yourself?
Click to expand...
Click to collapse
I bought splices and thought about extending the cable. It's possible.
galaxy s3
I did wanted to do the same but the extension cable didn't work. I looked at the connecting points and felt that the micro usb from Mel adaptor is to bit longer than usual so I thought that may be the reason and I shorten it resulting damaging my Mel adaptor itself. Now I am going for allshare cast wireless hub. So everyone please don't try to cut the micro usb pin from your adaptor or u will better decide to for my option to for complete flexibility.
I want to do this EXACT same thing but slightly more extreme:
I want an MHL adapter with 10-25 feet of micro USB cable on the end so I can use it from anywhere in my living room.
Is there any such cable/adapter?
Why do all MHL adapters come with only a 5 inch cable??? It is maddening!
*bump* I am looking for this too.. but I have a reason slightly different.. I have an AppRadio in my car that I connect my phone to. The MHL cable end is rather bulky and does not fit into the opening of my otterbox that is on my phone... most microUSB wires fit into the opening just fine.. Taking my phone out of the case every time I am in the car is rather ridiculous so I bought the micro USB extension (bought a 6" one).. didn;t even register except to charge... So, and ideas would be greatly appreciated..
Teej53214 said:
*bump* I am looking for this too.. but I have a reason slightly different.. I have an AppRadio in my car that I connect my phone to. The MHL cable end is rather bulky and does not fit into the opening of my otterbox that is on my phone... most microUSB wires fit into the opening just fine.. Taking my phone out of the case every time I am in the car is rather ridiculous so I bought the micro USB extension (bought a 6" one).. didn;t even register except to charge... So, and ideas would be greatly appreciated..
Click to expand...
Click to collapse
Get a different MHL adapter. I use an adapter close to the one 7 posts up by hedaleth with my kenwood system in my truck.
Hi,
Does anyone has any idea why the micro-USB connectors which are used to connect a HDMI or VGA cable to the micro-USB port of the Samsung Galaxies are longer than let's say a data micro USB connector?
I've tried a micro-USB extension cable, and they don't work with these video-output connectors because they're too long. When I looked inside the connector I noticed that all the connection points are way down the connector, and that the upper part is just extra. So I've tried filing off the upper part. Now it charges the phone, but still no video output.
Thanks!
Never mind, just found an answer to my question
Apparently the dock / video out connectors are 11 pin micro USB connectors. The data and charging cable connectors are 5 pin.
Now to find an extension cable for that. I wonder if this excists.
It would be much easier to find HDMI/VGA extension cable rather then the 11 ping micro usb.
golalmo said:
It would be much easier to find HDMI/VGA extension cable rather then the 11 ping micro usb.
Click to expand...
Click to collapse
Indeed, but the problem is that I want to extend the dock connector so I can put my Note 3 next to my dock to put it in landscape.
I can confirm that the Lecco USB-A to USB-C cords are of good quality free from soldering defects etc.
My non-charging symptoms are that the phone starts to charge and then stops charging, The USB cord works fine for file transfer
End to end connectivity of the cable is fine, The USB-A end connectivity to the charger on the (+Ve, Gnd, D+ D-) is intact.
There is a inline Fuse which was intact
A IR1 designated diode or resistor ? in the USB-C end .. It was open circuit ? I will work up a diagram when my eyes recover
I cannot confirm the contacts that the USB-C makes with the phone BUT the fingers all look fine. !
Mine is marked with the "Le" logo on one side, so it's easy to remember the side which you mention about. I had no problems with the cable and I never cared about the side of USB-A that I plug in.
Still, a good point though.
valy_cta said:
Mine is marked with the "Le" logo on one side, so it's easy to remember the side which you mention about. I had no problems with the cable and I never cared about the side of USB-A that I plug in.
Still, a good point though.
Click to expand...
Click to collapse
Yes mine has the logo as well, I concluded this possible cause for failure because its so easy to plug in reversed ? I will open the connector in the next few days to hopefully show where the failure occurs .
I've just compared the USB-A male from the OEM cable with another regular male port and I see that LeEco did a good job with it. The middle part is very thin and positioned very well. By plugging it into a female port and even reversing it, I haven't noticed any flexing of the middle part either way (I've watched it through the 2 small holes that keep the male port attached). There should be some movement, but I think it's too small to be noticed.
Anyhow, I'm looking forward to your disassembly of the connector.
valy_cta said:
I've just compared the USB-A male from the OEM cable with another regular male port and I see that LeEco did a good job with it. The middle part is very thin and positioned very well. By plugging it into a female port and even reversing it, I haven't noticed any flexing of the middle part either way (I've watched it through the 2 small holes that keep the male port attached). There should be some movement, but I think it's too small to be noticed.
Anyhow, I'm looking forward to your disassembly of the connector.
Click to expand...
Click to collapse
Scratch that theory ! Indeed the Lecco USB-A end is robust and NOT the problem ?! All wires to Pins test out ok.
I will need to investigate the USB-C end or the cable !
cheers
Thanks for the teardown.
I do agree that too many people were complaining about the cable that somehow it stopped charging, so there should be a weak point. Most of them reported failure within the first week or so, this makes me believe that it should be some bad soldering somewhere. It just needs few flexes and it's broken. I do suspect the junctions at the plugs either side.
Some safety precautions:
- Never remove the charger out of the socket by pulling the cable
- Never remove the cable out of the USB port (either side) by pulling the cable, pull it from the plug
- Whenever you are carrying the charger in a bag, remove the cable from the USB port
- When not in use, spin the cable to form a small coil of about 10cm in diameter (very subjective, the point is not to form an angle that might damage it; a 90 degree angle when caught between the drawers, etc)
PS: Was you cable broken or something?
valy_cta said:
Thanks for the teardown.
I do agree that too many people were complaining about the cable that somehow it stopped charging, so there should be a weak point. Most of them reported failure within the first week or so, this makes me believe that it should be some bad soldering somewhere. It just needs few flexes and it's broken. I do suspect the junctions at the plugs either side.
Some safety precautions:
- Never remove the charger out of the socket by pulling the cable
- Never remove the cable out of the USB port (either side) by pulling the cable, pull it from the plug
- Whenever you are carrying the charger in a bag, remove the cable from the USB port
- When not in use, spin the cable to form a small coil of about 10cm in diameter (very subjective, the point is not to form an angle that might damage it; a 90 degree angle when caught between the drawers, etc)
PS: Was you cable broken or something?
Click to expand...
Click to collapse
I can confirm that the soldering and the wire quality are top notch, End to end connectivity is good!
At the USB-C end there is a fuse inline with the +VE (Red wires) intact in my case, and a IR1 Zener diode (I think) , Or a resistor ?
Its open circuit ! (they normally go closed circuit ?) I have noticed sometimes plugging in the Power pack that the mains pins will give a little spark ?
So maybe that has blown the Diode ? IE Plugging in the powerpack with the cord attached might not be advisable ?
I have yet to work out the wiring .... of the IR1 diode / resistor ?
The only thing I cannot confirm is the contact made by the USB-C fingers onto the Phone connector..... I won't be doing any more.
Replacement cords are cheap
My cable is fine but I have a problem with my charger. It charges fine once, but having been disconnected (even midway through charging) it won't work again for at least a day. After about a day it generally works again, but again only one time. Very strange and annoying.
In Germany we have a couple of guys complaining about the Leeco OEM cable too. But if I remember correct these guys had a different kind of cable in their package.
USB-C to USB-C instead of the USB-A to USB-C variant.
That seems to be the case for people who had buying the phone from banggood with shipping from Europe direct.
Maybe there's another manufacturer of the cable with a bad soldering standard!?
My girlfriend and myself were both receiving​ our Max 2 with the USB-A to USB-C variant of the cable about nearly 5 Month ago and no issues so far!
USB-C to USB-C should be the way of the future for everything !
My cord had been working fine for 6 months, never unplugged from the charger, never rolled, never damaged.
It just went faulty after I had transferred files from my PC to the phone for a rom upgrade etc that the problem occurred.
Just coincidental ! ?
I tried to hook up a game controller via the OTG adapter and it appears to not send any power out from it. Even with a USB thumb drive and other USB C adapters, nothing seems to work. Has anyone else noticed this? You can transfer data via the cable just fine, but I find it strange it doesn't send any power through the plug.
Have you tried connecting it the other way round?
tomixnscale89 said:
I tried to hook up a game controller via the OTG adapter and it appears to not send any power out from it. Even with a USB thumb drive and other USB C adapters, nothing seems to work. Has anyone else noticed this? You can transfer data via the cable just fine, but I find it strange it doesn't send any power through the plug.
Click to expand...
Click to collapse
I noticed the same thing. I believe it's because once it comes out the other side with the 5-pin adapter, it is then reduced to the old micro-usb specification, which uses 5 wires. True USB-C connection has like 20 or 24 pins. I was able to get a couple very basic OTG of things to work, like a mouse and a thumb drive. BUT HERE IS THE CATCH - The mag connector has 5 pins, reduced from 20-some on the C connection.. so true USB-C connection is no longer possible once you get on the other side of the connector. So the trick is to NOT use a USB-C OTG when it's in the case with magnetic adapter. You must use a Micro USB OTG with a Micro-to-C adapter attached to that. Even so, not everything worked just by sticking on the Micro-to-C adapter.. Mouse and a thumb drive worked, but my ethernet adapter and VGA/HML/HDMI adapters did not. Out of the case, I can use my USB-C to HDMI cable to display on my TV. But same cord does not work with the magnetic adapter with the case. It is simply not possible because the reduction of contact pins from phone to case to magnet.. One more thing to consider, if you're trying to do anything other than charging, make sure the magnet is on the right way.. there's a little logo it should be in the front.
If I can come across a spare or broken Dual Screen case, I'd be curious to take it apart and see if it would be possible to rig it up with a better plug for the case.. find which wires go to the workings of the DS and leave them intact, but then try to replace the magnetic pins with a female C plug that has all the contacts intact still..
Seymour_Asses said:
I noticed the same thing. I believe it's because once it comes out the other side with the 5-pin adapter, it is then reduced to the old micro-usb specification, which uses 5 wires. True USB-C connection has like 20 or 24 pins. I was able to get a couple very basic OTG of things to work, like a mouse and a thumb drive. BUT HERE IS THE CATCH - The mag connector has 5 pins, reduced from 20-some on the C connection.. so true USB-C connection is no longer possible once you get on the other side of the connector. So the trick is to NOT use a USB-C OTG when it's in the case with magnetic adapter. You must use a Micro USB OTG with a Micro-to-C adapter attached to that. Even so, not everything worked just by sticking on the Micro-to-C adapter.. Mouse and a thumb drive worked, but my ethernet adapter and VGA/HML/HDMI adapters did not. Out of the case, I can use my USB-C to HDMI cable to display on my TV. But same cord does not work with the magnetic adapter with the case. It is simply not possible because the reduction of contact pins from phone to case to magnet.. One more thing to consider, if you're trying to do anything other than charging, make sure the magnet is on the right way.. there's a little logo it should be in the front.
If I can come across a spare or broken Dual Screen case, I'd be curious to take it apart and see if it would be possible to rig it up with a better plug for the case.. find which wires go to the workings of the DS and leave them intact, but then try to replace the magnetic pins with a female C plug that has all the contacts intact still..
Click to expand...
Click to collapse
Thank you @Seymour_Asses ! I saw here https://twitter.com/konic0s/status/1202966945693220865 that LG G8X supports USB-C to HDMI adapters but I didn't know if it also worked with the Dual Screen case but now I know it doesn't, thanks for the information, very helpful ! :good:
BTW I think that when you connect the Dual Screen case to the G8X it uses the dedicated USB-C high speed pins of the G8X for video-out so these pins are not available anymore for other HDMI out, I'm not sure about it and don't have any proofs but it seems you are right about not enough pins on the mag connector.
If i remember correctly, the manual states that most USB-C functions wont work though the dual screen case. I think there was some speculation that its due to most of that bandwidth being used for the second screen.
Quite simple: the Mag USB-C adapter is for charging only. It drives me mad as i have a professional USB-C headphone that I use for conferencing.
But I understand the reason: when in dual screen, the USB-C data connection is in use dor the second screen, enabling the USB-C connection beyond that requires a hub to be built in the case "before" the DS connection (so it wont work building it in the dongle itself).
I wish LG went with a Pogo connector on the bottom or on the side to activate the DS case. This would have made the chin slimmer and freed up the USB-C port.
Anyway, it is what it is now, and i will not trade my LG G8x DS for anything at the moment... Until maybe that Surface Duo phone for which I might need to sell a vital organ ?