I have a radar stuck in demo mode, need to flash the official tmobile us rom. I have the USB drivers installed and the device manager shows that they are installed properly, but windows mobile device center doesn't see hte phone, whether its in normal mode, or bootloader mode.
I think I need mobile device center to see the phone, because RUU says activesync is necessary, and it aso gives me an error when I try to install the proper rom, that it can't find the device properly.
Any tips? Help is appreciated, I would even tip someone $5 paypal if you can give me the info needed to sucessful flash the rom. (I was trying to flash by running the Omega European RUU.exe, then replacing it with the t-mobile .nbf before installing in the temp files)
Thanks!
Related
I currently have the above using Rom verdion 3.16.32 ENG. I have tried downloading the unlock programme without succesess. I get the message 'not a valid Win 32 application' Can anyone help so Ican unlock this devise from o2 network
Thanks
First of all welcome to the forum.....
Second:
Would you be so kind to make a backup of the ROM and send it to me?
Process how this can be done is here:
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_FlashXDATool
For unlocking I´m nearly 100% sure that you require a different ROM on your device. The unlock tool you have doanlooaded should be run on your Wallaby device....
But it requires the Wireless modem function in the ROM, and i think this is not available in your ROM. For unlocking you have to flash a new ROM.
Therefore download the Special Edition ROM
ftp://xda:[email protected]/Wallaby/ROM/Special/special_rom_1.2.exe.zip
Unzip the file, connect your device via ActiveSync to your PC and run the Exe file on your PC.
Than just folllow the instructions on the screen.....
Regards
Stefan
I have An HTC (PM2oo) device locked to T-Mobile. It has code on it and i need to do simunlock on it. please help me. I also have HTC 2125 for sim unlock. I copied XDA sinlock exe. into the phone and ran it in the phone but no success.
Hi,
I upgraded ROM on G4 Wizard CID-locked wizard from T-Mobile CZ 2.21 to Superrom 1.1. But after flash, wizard stuck in splashscreen with IPL/SPL.
I can go to bootloader, but when I tried to flash another ROM via RUU (T-Mobile CZ official, Superrom for CID-locked G4 or Novii Love), RUU said - Connection Error. Simply AS and RUU can't connect to PDA. PC identified Unknown device, when I plugged wizard to PC
I tried it on 2 PCs (1. AS4.2, 2. AS 4.5 beta2), nothing....
Any ideas ? Thanks very much
Are you doing it in the correct order? That sounds dumb i know...but i had a similar problem and found out it was because i wasnt doing it in the correct order.
You have to setup bootloader and then connect usb, if you do it the other way around you get some funny errors. Thats just what i found....it may not be of help to you.
Sorry if you know this already, just trying to help, im new too.
ROM
I know i wont be fixing your problem, but, you can be sure that after the comunication problem is solve, you can use the WizardLove rom.
I mess with my phone recently, and i got stuck at the bootloader, and that rom was the only one that worked.
Ok, thank you
Problem was found. When I tried to find driver for PPC automatically, PC found nothing, but when I manually chose driver from AS\Drivers, PC driver found
Now I can flash via RUU
i had the same problem was working till 5 am to solve it
folow the directions in this thread and it should be alive once again
http://forum.xda-developers.com/showthread.php?t=294107
I have tried many times to upgrade the Rom Image on my HTC Tytn (Cingular 8525) with no success. I am getting a 260 error with the program located at this link...
http://forum.xda-developers.com/showthread.php?t=293665
I did first run the unlocking application to unlock both SIM and CID before running the upgrade.
I followed all the steps exactly and have had no success...
The following might be effecting my attempt:
I am running my pc on Vista
I am syncing with Windows Mobile Device Center
I have tried to solve this problem for about two weeks. Can anyone help me?
Mrvanx has a guide on how to prepare Vista for flashing, you can find it here.
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Same problem
compwiz2008 said:
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Click to expand...
Click to collapse
Same problem here trying to change the radio version after changing the bootloader........
Connection alwayse lost just as said above.
Any help will be appreciuated
justx24
Use the RUU wrapper with the NBH file you want to upgrade.
I still have the same issue, even when using the RUU Wrapper and any nhb.
don't use vista
Ok, got one step furthur
I reached the point where the ROM Begins to update, which is VERY good...
The ROM update Reaches 1%, then waits for 20 minutes...
Then I get a 262 error and have to go through recovery, try again, with the same result.
i have same problem plz help thnx in advance
compwiz2008 said:
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Click to expand...
Click to collapse
Have you tried removing or adding a checkmark to the USB to PC in CONNECTIONS on your device? I remember having a similar problem when I installed Radio Rom 1.38 that my USB connection was lost with the pc . I am using XP when flashing so if you have no luck then do this on a XP machine.
Forgot to ask! What ROM are you trying to flash??
@compwiz2008 and ahmerpar
I read somewhere that running windows update will update WMDC........maybe give that a shot?
Maybe you can try to upgrade your ROM from your SD card.
Nope
Let me try that...
Still did not work
I'm probably going to just take my phone to a computer repair shop and pay them to deal with it, since I'm evedently doing something wrong.
OK, so I tried to install nand android on my htc hd2 and firstly I installed hspl 3 on it then as instructions said I updated ROM version to MAGLDR ... And now phone is frozen right after I turn it on it only shows me O2 welcome message. Please don't tell me that it is coz the phone is locked to o2 network because there r so many threads and no one mentioned that u can't install android if the phone is locked or I missed something SO any help pls? I am freaking out that my phone is dead.
RAM 512
ALso:
When I press a red button near the sim card while holding volume down and it shows 3 colour screen and connect it to the pc , pc does make a sound as phone was recognised but it doesnt come up with any windows or anything that I could see that phone is there.. Is there any way I can install old rom or smthing to get my poor phone back, please help me, I am not experienced in this at all and first attempt failed
Put the phone into BootLoader mode. At the bottom of the screen you will see 'Serial'. Now plug it into your computer and the 'Serial' changes to 'USB' - you have made a good connection to the computer. The computer doesn't recognise it as a phone, because the phone firmware has not been booted up, so don't wory about it.
Run the O2 ROM form the computer. One of the conditions is that you have made an ActiveSync connection, just tick the box and proceed.
Once the ROM has flashed, it is advised to do a hard reset, but I have never had a problem not doing it.
Now you are back to the begining.
You are getting a little mixed up between Operator (SIM) Locked and Firmware Locked. They are independant of each other. You can SIM unlock your phone, which means you can use any telecom's SIM card in your phone even though the phone boots up with an O2 logo. You can unlock the firmware (HSPL) so that you can use the stock HTC ROM (not the 3.14 version) or one of the excellant custom ROMs, now the phone won't show any of the O2 stuff but you are still limited to using O2 SIM cards.
Now you have to Run HSPL2 and select the SPL 2.08.HSPL. Since you want to run Android NAND you have to flash a .50 RADIO - try the 2.15.50.14 RADIO.
I would have a real good read * HERE *. And if you want to go ahead, the read it again.
I got one of these, he came with android when i buy it, so i change to windows phone beacuse the battery was draining fast.
I install windows phone 7 with magdlr help, but i want to try others rom from 6.5 artemis or the bsb best but i try to install with magdlr and didn't work. I read i find out that i need something call hspl or spl, i try to install but i need version 1.43 at least i dont't have it. I try to install another that game a version of spl updated but mgdlr dont accept me the others rom to update the spl to 1.43.
And i put the phone in normal mode with the usb my windows 7 64 bits don't detect the phone missing drivers i guess but i already install drvupdate-amd64 i don't know why he doesn't recognize it. While mgdrl mode and recovery (green, red etc lines) he did recognize it.
What i can do??? I very new i been reading but this spl and drivers isues stop me
You cannot flash Windows Mobile 6.5 ROMs with MAGLDR.
On your PC, you should install Windows Mobile Device Center to get the correct USB drivers. Then, you should flash first the official TMOUS ROM to delete what´s on your device, re-flash HSPL (using HSPL3 or HSPL4) and then the custom ROM you want.
This way, old stuff incl. MAGLDR any maybe a wrong Radio ROM will be gone.
For all you need to do, please check the stickies in the ROM thread (how to flash your first custom ROM etc.).
Kenshin1870 said:
I got one of these, he came with android when i buy it, so i change to windows phone beacuse the battery was draining fast.
I install windows phone 7 with magdlr help, but i want to try others rom from 6.5 artemis or the bsb best but i try to install with magdlr and didn't work. I read i find out that i need something call hspl or spl, i try to install but i need version 1.43 at least i dont't have it. I try to install another that game a version of spl updated but mgdlr dont accept me the others rom to update the spl to 1.43.
And i put the phone in normal mode with the usb my windows 7 64 bits don't detect the phone missing drivers i guess but i already install drvupdate-amd64 i don't know why he doesn't recognize it. While mgdrl mode and recovery (green, red etc lines) he did recognize it.
What i can do??? I very new i been reading but this spl and drivers isues stop me
Click to expand...
Click to collapse
Man. You are lucky all those flashing with MAGLDR didnt really screw your phone for good.
Here is an eye-opener and best method in my opinion you shud follow.
1- Find the original ROM for your HD2 (This is easy using your serial number located under the battery). Google for T-Mobile ROM update and eventually you will be in T-Mobile Update site.
2- No luck in step 1? No Problem. Just read the sticky on how to install HSPL 2.08 by Cotulla. Then install the radio version 2.15.50.14.
DONT FLASH ANY RADIO WITH THE VERSION 2.15.5X.14 (X being equal to any number) In plain ENGLISH...dont flash a RADIO with 51. Only flash with 50 for TMO HD2
3. Now reboot your device in Bootloader mode and install any Windows ROM you want. Just steer clear of MAGLDR and flashing until you have proper knowledge and patience. Else you might end up with a dead HD2
I try to download the official rom and i found an uk version
But before this i have one problem the usb driver, i already install them with windows mobile device center too and still my pc dont detect the phone, is missing two drivers, two unknow devices.
Kenshin1870 said:
I try to download the official rom and i found an uk version
But before this i have one problem the usb driver, i already install them with windows mobile device center too and still my pc dont detect the phone, is missing two drivers, two unknow devices.
Click to expand...
Click to collapse
You could seriously damage and brick your phone flashing a non-US ROM onto your device. Why didn´t you check the ROM threads more carefully? Or the hint the previous poster gave you?
Maybe the fact you don´t get the driver thingy right saved your HD2.
And also, did you try flashing from the normal bootloader then? Another option would be to use the SD card method.
But then again, this would require some reading from your side. If you don´t like reading, you shouldn´t start flashing.
I have benn reading i try to install in bootloader but everytime i try thrown me a error and the the phone do a restart.
My spl version now is nspl 0.96.2250.0, so i cannot install hspl because at least i need the 1.42 version, i cannot install rom from normal mode, the only way i got is bootloader (assuming that doesn't keep popup that error) and magdlr.
Did you know how can i get a official rom that come with a higher spl version and be exceted from booloader or magdlr??
Kenshin1870 said:
I have benn reading i try to install in bootloader but everytime i try thrown me a error and the the phone do a restart.
My spl version now is nspl 0.96.2250.0, so i cannot install hspl because at least i need the 1.42 version, i cannot install rom from normal mode, the only way i got is bootloader (assuming that doesn't keep popup that error) and magdlr.
Did you know how can i get a official rom that come with a higher spl version and be exceted from booloader or magdlr??
Click to expand...
Click to collapse
Where from did you get the bootloader version information? As far as I remember, that is the version which comes from WP7. Strange, somehow.
Original Windows Mobile ROMs cannot be flashed via MAGLDR at all.
You must enter the standard bootloader, which is loaded *before* MAGLDR.
To do this, turn off your device, turn it back on pushing vol. down and power on at the same time - * and keep them pushed* until you see the multicolor bootloader screen. In this screen, you should be able to read what SPL version is on your device.
I do again recommend to flash an original ROM via SD card method (using a 2GB, FAT32 formatted card), please check here for the how-to. The ROM should be available here (be careful not to flash a test ROM, but a stock ROM!).
I succeded, i have to do it throw sd card method, and install the RUU_Leo_1_5_TMOUS_2.07.531.6_Radio_Signed_15.33.50.07U_2.07.50.27_2_Test rom.
Now i have spl 2.07 installed, i will proceed to install hspl 4 i guess, to flash roms
Thanks man