Solved: Wifi Hotspot issue Samsung Galaxy S2 Telstra - Galaxy S II Q&A, Help & Troubleshooting

Hi All,
I think I have finally cracked it. I have had this issue since getting my SG2 out of the box and i have read every forum possible for a solution. I mean i have tried everything until this:
Fix: This is for those people using their phone as a wifi hotspot that get a successful connection to their laptop or Tablet etc but cannot use the internet because of DNS issues. I.e, when connected to your laptop you establish a connection but get a limited connectivity warning.
Steps:
1. ensure you are on ICS
2. I want you to re download a fresh set of your APN's from telstra - http://configure.telstra.com.au/telstra/index.jsp (Follow your nose with this bit, you want the one that downloads all of them)
Now the fix!!
3. Go to Settings> more>mobile networks>access point names
4. Click on Telstra internet (telstra.iph)
5. Scroll down to APN Type
6. Type: default,supl,internet,dun
7. press menu then save
Your Done.
Your data notification will switch off and then back on in about 15 secs and away you go.
I really hope this helps those that have had this issue for ages.
Mewsik.

Hi,
I would be interested to see your feedback if this fix worked for you. I have had 2 work friends have the same issue and the above post fixed their wifi hotspot issue.
Cheers.

sorry to resurrect a super old thread, but i just want to say that this worked for me and thank you.
i am using openvpn and for some reason my "push dns" server rule was not applying to my phone. the computer kept pointing to my phone's ip as the dns resolver, but my phone was not resolving anything (most likely it was trying to resolve from localhost) but after i applied the above, openvpn push rules correctly applied and my computer now accepts the dns from my server automatically.
my setup:
openvpn server -> openvpn on phone -> usb tether -> computer
this way my computer's traffic is routed through openvpn on my phone so dont have to install it on my computer basically a portable vpn 'server'. this works for wifi as well so any clients that connect will also route through vpn.

Do you even have an I9100 ?

I can't believe they let this drag on this long without a fix. Upgrading to Kitkat was the worst mistake ever.
My VPN was flawless on 4.3 .... Someone please figure out how to downgrade back to 4.3.
Thanks OP for the info.
Total_Lag said:
sorry to resurrect a super old thread, but i just want to say that this worked for me and thank you.
i am using openvpn and for some reason my "push dns" server rule was not applying to my phone. the computer kept pointing to my phone's ip as the dns resolver, but my phone was not resolving anything (most likely it was trying to resolve from localhost) but after i applied the above, openvpn push rules correctly applied and my computer now accepts the dns from my server automatically.
my setup:
openvpn server -> openvpn on phone -> usb tether -> computer
this way my computer's traffic is routed through openvpn on my phone so dont have to install it on my computer basically a portable vpn 'server'. this works for wifi as well so any clients that connect will also route through vpn.
Click to expand...
Click to collapse

great, it also worked for me (Samsung S7, Proximus operator in Belgium), thanks!!!

Related

***HOWTO: Internet Sharing over WiFi*** (Updated 08-Nov-2007)

I have figured out how to use Internet Sharing over WiFi, which essentially makes my Hermes an Access Point.
Do the following:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (for the Hermes). It should currently be "BTPAN1".
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc")
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
And it works!
Interestingly, while IS was enabled, wifi stayed on and connected when the phone went to standby mode. Normally wifi turns off to save battery during standby. I imagine this will drain your battery in a hot minute, so bring your charger.
UPDATE (28-Oct-2007): Attached are some more beta releases of patched intshare.dll. I've created versions for most of the adapter names people have requested. By renaming this dll to intshare.dll and copying it to \Windows, Internet Sharing will use TIACXWLN1 (or whichever dll you use) when Bluetooth PAN is selected. I.e., if you use this, you will not need to make the registry changes above.
This will handle the registry part, but of course you'll still need to set up the ad-hoc network on your own.
UPDATE (03-Nov-2007): I've attached a beta version of the patched Internet Sharing app. It's in its own cab so it won't overwrite your existing IS. This app replaces Bluetooth PAN with 802.11b/g Wireless Ethernet. No registry hacking required. This app is well suited to replace the MS version on cooked ROMs.
If you use an adapter other than TIACXWLN1 then replace intshare.dll just as before.
UPDATE (08-Nov-2007): Attached is v 0.9.1 of the Internet Sharing Mod. This update addresses the 10 minute disconnect bug most people have experienced.
best,
fluxist
This is the first thing I'll try when i'm at home again!
I can't believe this! Waiting for this since i got my Hermes. Thx for this development. This is the greatest effort since Hard-SPL and WM6 upgrade.
Now I can connect my XBOX360 to the Internet without starting my PC and sharing it over PC-LAN. USB-Charger is at the Front of the XBOX360.
I hope it will work.
You said the Max-Connections can be reworked. Does this mean it will support Ad-Hoc AND WLAN-Routing to many recepients too?
This worked for me too on a Kaiser/TYTN II
I'm doing some additional experimentation to see what exactly this can do - for instance to replace a bluetooth connection to a laptop with a wifi one?
odessaranger said:
I'm doing some additional experimentation to see what exactly this can do - for instance to replace a bluetooth connection to a laptop with a wifi one?
Click to expand...
Click to collapse
not sure what you mean by replacing the connection. With ICS, obviously you cant share your connection over BT while sharing it over WIFI. and you can normally use wifi to connect to another computer by using an ad-hoc connection and manually entering a private ip on the same subnet for each computer.
this is awesome. worked perfectly for me.
After trying to stuff around with a proxy server for days and then you come along with something as simple as this....
boniestlawyer said:
this is awesome. worked perfectly for me.
After trying to stuff around with a proxy server for days and then you come along with something as simple as this....
Click to expand...
Click to collapse
Were you able to use more than one client connected?
I'll admit..when I saw this my first thought was that this was another "How can I do internet sharing via wifi" and the title was just misleading..instead I find myself very impressed with your accomplishment. Very well done! As a "hack" untill you figure out how to mod the dll which I'm sure is only a matter of time now that you have pointed everyone in the right direction, you can export the registry key for both the Bluetooth adapter and the Wifi one and "import" whichever one you want to use at a given time...it's not pretty but it should work.
Some issues of concern would be that the AP is wide open and can be connected to by anyone with no password etc...the bluetooth pairing allowed some security but using the wifi doesn't have the same shared key protection...or am I missing something obvious?
fluxist said:
I have figured out how to use Internet Sharing over WiFi, which essentially makes my Hermes an Access Point.
Do the following:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (it should currently be "BTPAN1").
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc"
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
And it works!
When I used it I was only able to get one client to connect, however there is a reg value, HKLM\Comm\BTPAN1\Parms\MaxConnections that may help if it is changed from 1 to 2 (or whatever). But I haven't tried.
Interestingly, while IS was enabled, wifi stayed on and connected when the phone went to standby mode. Normally wifi turns off to save battery during standby. So that's a good thing, although I imagine this will drain your battery in a hot minute, so bring your charger.
I was going to release a patched intshare.dll so that the normal Internet Sharing utility can do this, but I'm having trouble changing the section addresses in the dll to the right values after I add data. If anyone knows how to do this PM me and I'll give you the details.
best,
fluxist
Click to expand...
Click to collapse
thank you.
this work actually stemmed from my trying to share my phone's tethered connection with another client. by which i mean, my laptop is in a cafe online through my 8525 using Internet Sharing(IS) over usb. and i want to provide a connection, through wifi or ethernet, to my gfriends laptop. this actually isnt normally possible b/c WM IS and XP Internet Connection Sharing (ICS) both have 192.168.0.1 hard-coded as the gateway IP. so the phone uses that IP to give my laptop a connection, and my laptop tries to use the same IP with ICS. anyway, it fails because of this. i was able to get past that problem by going into Settings -> Wi-Fi -> Network Adapters -> Remote-NDIS and manually setting 192.168.1.1. This lead to the breakthrough with regards to wifi. prior to that id been trying all different ways to have the wifi adapter spoof the bt pan, however i could never get dhcp to assign an IP to the client. this is what it took.
and it's great that DHCP does in fact work here. it makes it dead easy for any arbitrary client to get online. just join the adhoc network as if it were an AP.
anyway, security-wise the ad-hoc network can use WEP or WPA, so security doesn't have to be a problem. the procedures for doing this are the same as normal.
and i haven't tried that reg key to enable multiple clients. but it looked like an obvious choice. i'll leave that as an exercise for the reader
fluxist
I ran into same issue with XP internet sharing. Another workaround is to have a linux machine do NAT( since you can specify the IP used there) to whatever other clients you want and have it connected via bluetooth dun or bluetooth PAND (which is the solution I use to give internet to my replaytv and a couple of laptops in the house)...my edge connection is my main internet feed..a cacheing proxy such as wwoffle, squid of my personal preference "polipo" helps alot to when using gprs/edge etc since it helps with the latency.
fluxist said:
thank you.
this work actually stemmed from my trying to share my phone's tethered connection with another client. by which i mean, my laptop is in a cafe online through my 8525 using Internet Sharing(IS) over usb. and i want to provide a connection, through wifi or ethernet, to my gfriends laptop. this actually isnt normally possible b/c WM IS and XP Internet Connection Sharing (ICS) both have 192.168.0.1 hard-coded as the gateway IP. so the phone uses that IP to give my laptop a connection, and my laptop tries to use the same IP with ICS. anyway, it fails because of this. i was able to get past that problem by going into Settings -> Wi-Fi -> Network Adapters -> Remote-NDIS and manually setting 192.168.1.1. This lead to the breakthrough with regards to wifi. prior to that id been trying all different ways to have the wifi adapter spoof the bt pan, however i could never get dhcp to assign an IP to the client. this is what it took.
and it's great that DHCP does in fact work here. it makes it dead easy for any arbitrary client to get online. just join the adhoc network as if it were an AP.
anyway, security-wise the ad-hoc network can use WEP or WPA, so security doesn't have to be a problem. the procedures for doing this are the same as normal.
and i haven't tried that reg key to enable multiple clients. but it looked like an obvious choice. i'll leave that as an exercise for the reader
fluxist
Click to expand...
Click to collapse
Impact on BT?
What a brill find. Well done.
Does it break anything with bluetooth?
Tx
can someone elaborate what this is for, maybe give a sample scenario on using this?
Is this basically allowing a computer to use the internet connection of the pda phone (ie EVDO, 1RxTT, etc.) through wifi, instead of bluetooth or USB cable? (ie tethering?)
if someone manages to get this working with xbox 360 make a tutorial plx ;D
superflysocal said:
can someone elaborate what this is for, maybe give a sample scenario on using this?
Is this basically allowing a computer to use the internet connection of the pda phone (ie EVDO, 1RxTT, etc.) through wifi, instead of bluetooth or USB cable? (ie tethering?)
Click to expand...
Click to collapse
thats what i wanna know , could i use my hsdpa connection via wifi to my psp?
I'll do a tutorial when i'm at home again. Maybe somebody with know-how can make a cab-file v1.0 for this "WLAN-Modem hack".
This surely will be a great app.
yes, your xbox and your psp should be able to connect just fine, as long as they support ad-hoc wireless (which i imagine they must). this hack will allow the phone to act like any normal wifi access point. the only difference is the client has to be seraching for ad-hoc networks in addition to normal APs.
the difficulty with creating a cab file at this point is that the registry setting is not persistent. that is, it must be set each time you enable IS. the setting is lost every time IS starts. this is why i am trying to patch the dll - so wifi will work as a normal, additional option in Internet Sharing (and hopefully this should be ready soon).
fluxist
when you say click "IEEE 802.11b/g Compatible Wi-Fi" do you mean the wifi network adapters in my case would be "tiacxwln compatible wireless ethernet"? im trying it on a 6700 WM5
I would LOVE to get this working on my TMO WM6 Wing, but I'm having issues:
1) Open Settings->Internet Sharing. Enable IS for Bluetooth PAN.
Got it - except on my device it's Programs -> accessories -> IS
2) Change HKLM\Comm\ConnectionSharing\PrivateInterface to "TIACXWLN1" (it should currently be "BTPAN1").
Check - but is the T1ACXWLN1 device specific? If so, how can I find the interface ID on my device?
3) Open Settings-> Connections -> Wi-Fi. Select Network Adapters tab. Click IEEE 802.11b/g Compatible Wi-Fi.
For me it's settings -> connections -> network cards, but I don't have an IEEE 802.11 listed. I connected to an existing AP, and found that my 'SDIO WLAN Wireless Adapter' does receive a DHCP address, so I tried changing it to 192.168.1.1...
4) Enter IP address 192.168.1.1 and subnet mask 255.255.255.0. Click OK.
5) Select Wireless tab. Add New.. to add the Network name for your ad-hoc network (I prefer "adhoc"
Found this and set up my WING-FI network.
6) Set the client computer to use the same ad-hoc network. Client will receive an IP address from the device (don't need to manually set the IP).
The client PC connects to WING-FI, but never receives an IP address...
What could I be doing wrong? Is it the hardware ID in the registry? I've created the network with WPA, then after the connection problems, with no security - but still no change.
Thanks!!
Ryan
neonstorm said:
I would LOVE to get this working on my TMO WM6 Wing, but I'm having issues...
Click to expand...
Click to collapse
Very likely the string TIACXWLN1 needs to be something different. Check HKLM\Software\WZCSV\Parameters\Interfaces\
There should be a key there with the name of your wireless adapter. It should end in "1".
And if not there, it should also be visible under HKLM\Comm\
Let us know how it works out.
EDIT: I just noticed you typed T1ACXWLN1. The string must be TIACXWLN1. That's "i" not one.
fluxist
I own a PPC6700 as well and I was able to get it working no problem other than the fact that our wireless adapter is not the same as the one mentioned. The reg edit is the same it's just the first network adapter in the list when you create the network settings.
fluxist said:
yes, your xbox and your psp should be able to connect just fine, as long as they support ad-hoc wireless (which i imagine they must). this hack will allow the phone to act like any normal wifi access point. the only difference is the client has to be seraching for ad-hoc networks in addition to normal APs.
the difficulty with creating a cab file at this point is that the registry setting is not persistent. that is, it must be set each time you enable IS. the setting is lost every time IS starts. this is why i am trying to patch the dll - so wifi will work as a normal, additional option in Internet Sharing (and hopefully this should be ready soon).
fluxist
Click to expand...
Click to collapse
If you send me the dll I could look into it.
i have some experience with editing dlls.
good work man

[UPDATED 2/25/2009] SocksProxy v1.0: Free SOCKS proxy for internet sharing

I have created an SOCKS proxy server application to run on Windows Mobile phones. A SOCKS proxy is a proxy server that is capable of forwarding nearly all types of network traffic, similar to a NAT router. It is very simple to use. Simply type in the port you would like the proxy server to listen on (defaults is 1080), then click the large "Start Proxy" button.
In order to run this application you will need the .NET Compact Framework 3.5 installed on your device.
Some applications are SOCKS-ready and others are not. You can use FreeCap (freeware) to SOCKS enable any Windows application. ** FreeCap seems to have problems connecting to SocksProxy. Let me know if it works or doesn't work for you. **
I am *NOT* responsible for any fees charged to anyone for the use of this software. There is no warranty and no guarantee.
[UPDATE 2/25/2009]
I've completed the new version of SocksProxy. It implements socks version 4a. There is no security, so it will allow anyone to connect with any user id.
Please let me know of any issues you find.
[UPDATE 2/24/2009]
SocksProxy v1.0 Reboot
--------------------------------------------------------------------------------
I've completed the new proxy server. It looks pretty much like the old one, but I've anchored the controls to the edges so it should scale properly with VGA devices.
I've written a new Socks 4a proxy from scratch and completed ditched all the old code. It seems to be working pretty well, though a bit slow. I think I need to increase the size of my read buffers. I will have to write a smarter heuristic for determining the size of the buffer per connection though. I have them at 128 Kb now. I need to grow each buffer dynamically according to how it's being used, that way I don't create large buffers for connections that are only transfering small amounts before closing (downloading a small gif or javascript file, for example).
I'll probably release it tomorrow after some more testing.
BTW: I'm posting this through the proxy right now!
[UPDATE 2/24/2009]
I've decided not to move forward with the J2ME version of SocksProxy. I will however be writing a new .NET CF version. The current version's proxy is based on code I ported from a proxy targeted to the standard .NET framework. Some features in the standard framework are absent in the compact framework. When porting the proxy I pretty much just did it as quick and dirty as I could because I really wanted something that just got the job done. I didn't care how stable or 'good' it was because I hadn't even intended on releasing it to anyone. Since it looks like there's still a lot of interest I will be writing a new one from scratch. Don't expect too much; It'll be the simplest thing that possibly works, but it'll be stable and reliable.
I'll be naming this version SocksProxy 1.0 Reboot. I'm not upping the version number because I'm really not going to be adding any new features.
[UPDATE 11/4/2008]
I am working on a J2ME version of this application. I will no longer be maintaining the .NET version of the application. The SVN repository for the .NET version will continue to be available. I have no plans on taking it down.
I have decided to switch to J2ME because I will be able to reuse source code in a future Android release -- that is, if Google or someone adds the ability for Android to have more than one IP address.
[UPDATE 10/27/2008]
There is a usage issue with the application with certain configurations of Windows Mobile and Activesync. It seems that when the Activesync host (your PC) has a connection to the internet the handheld device will prefer to connect to the internet via the PC's connection rather than its cellular connection. This completely eliminates any benefit to using the proxy. Does anyone know how to prevent the handheld from routing its internet traffic back through Activesync? Note that this is NOT solved by setting the "Allow data connections" setting in Activesync.
[UPDATE 10/27/2008]
I have updated the SVN respository (https://pchasco.homedns.org/svn/SocksProxy/trunk). Here are the changes:
* Changed "Listening on" box to list all IPs on the handheld
* Added an IP box. Enter an IP to listen on that IP or leave blank to listen on all.
* Rearranged form
* Added "Use selected IP" button to insert into the IP box the IP selected in the list of available IP addresses.
You can enter any IP address in the IP box, but the proxy will fail to start if the IP is not valid for your device.
Hi pchasco,
Could you explain a bit more what this does (and how it works)?
The reason I ask is that I'm looking for an application for the PPC which allows me to share its internet connection by pointing the Desktop browser' proxy to the PPC.
This allows me to be connected to the wired network and using this proxied browser to browse even the blocked sites ...
Can your application be used for this?
If so could you also explain how it works..
I've ran the App on my PPC, and clicked start, this gave me an IP address
next i hooked it up to USB and pointed IE's proxy to that address...didn't work
I also tried to activate the 3G first and/or with ICS activated
but both times I didn't see a IP address...
I'm probably doing something wrong..
Thanks
This is a SOCKS proxy, so it does not work in quite the same way that a normal HTTP proxy does. For internet explorer you'll have to open the advanced proxy options and fill in the information for the SOCKS hostort entry.
Can someone please explain a sample usage of this software on Windows Mobile?
pchasco said:
This is a SOCKS proxy, so it does not work in quite the same way that a normal HTTP proxy does. For internet explorer you'll have to open the advanced proxy options and fill in the information for the SOCKS hostort entry.
Click to expand...
Click to collapse
Have you used this with ICS? In other words, share your internet connection with a computer and then have the computer connect via your sock proxy to the internet?
abdulzis said:
Can someone please explain a sample usage of this software on Windows Mobile?
Click to expand...
Click to collapse
I'm not sure what you mean. An example of how to use it or an example describing why someone would want to use it?
hoopsbwc34 said:
Have you used this with ICS? In other words, share your internet connection with a computer and then have the computer connect via your sock proxy to the internet?
Click to expand...
Click to collapse
I am not sure why you would need to use both SOCKS proxy and ICS at the same time. They are both means to provide internet connectivity through your phone to another device. If ICS were an option on my phone, I would use it over SOCKS unless the client device did not support it.
pchasco said:
I am not sure why you would need to use both SOCKS proxy and ICS at the same time. They are both means to provide internet connectivity through your phone to another device. If ICS were an option on my phone, I would use it over SOCKS unless the client device did not support it.
Click to expand...
Click to collapse
Basically, I'm trying to allow access to two networks at the same time. So I want to adjust my settings in firefox to point to my WM phone and your socks proxy. Then my other applications and IE can use my LAN. Otherwise, to get my WM ICS to work I have to disable my LAN connection which I need for certain apps.
edit... I'm good with using it without ICS, but that doesn't seem to work either. No matter when I click start proxy, I get an IP of 0.0.0.0 and if I connect my computer via USB I can't ping that address.
hoopsbwc34 said:
Basically, I'm trying to allow access to two networks at the same time. So I want to adjust my settings in firefox to point to my WM phone and your socks proxy. Then my other applications and IE can use my LAN. Otherwise, to get my WM ICS to work I have to disable my LAN connection which I need for certain apps.
Click to expand...
Click to collapse
Then setting the SOCKS proxy setting without setting any other proxy settings should work in Internet Explorer. I've been trying to test it, but my phone refuses to access the internet through the cellular connection right now; it's always going through my PC while activesync is connected. I can't get it to stop! The funny thing is IE on my PC is making its HTTP requests through my phone, then my phone is going right back through my PC to the internet!
pchasco said:
Then setting the SOCKS proxy setting without setting any other proxy settings should work in Internet Explorer. I've been trying to test it, but my phone refuses to access the internet through the cellular connection right now; it's always going through my PC while activesync is connected. I can't get it to stop! The funny thing is IE on my PC is making its HTTP requests through my phone, then my phone is going right back through my PC to the internet!
Click to expand...
Click to collapse
That's what I tried... but the IP address I get is 0.0.0.0 from your app. What IP do you usually get back when you run it? Do you just connect via USB? If ActiveSync is running is that an issue?
pchasco said:
Then setting the SOCKS proxy setting without setting any other proxy settings should work in Internet Explorer. I've been trying to test it, but my phone refuses to access the internet through the cellular connection right now; it's always going through my PC while activesync is connected. I can't get it to stop! The funny thing is IE on my PC is making its HTTP requests through my phone, then my phone is going right back through my PC to the internet!
Click to expand...
Click to collapse
I think there is a setting in ActiveSync that says "allow wireless connections when connected" sounds like that might be your problem.
Mr_Gee said:
Hi pchasco,
Could you explain a bit more what this does (and how it works)?
The reason I ask is that I'm looking for an application for the PPC which allows me to share its internet connection by pointing the Desktop browser' proxy to the PPC.
This allows me to be connected to the wired network and using this proxied browser to browse even the blocked sites ...
Can your application be used for this?
If so could you also explain how it works..
I've ran the App on my PPC, and clicked start, this gave me an IP address
next i hooked it up to USB and pointed IE's proxy to that address...didn't work
I also tried to activate the 3G first and/or with ICS activated
but both times I didn't see a IP address...
I'm probably doing something wrong..
Thanks
Click to expand...
Click to collapse
Sounds like the same thing that is happening to me. I finally got it to give me an IP address, but only if my data connection is inactive. As soon as the data connection is active it becomes a 0.0.0.0 IP address. Bug?
I tried to establish the IP, then activate the data connection... still doesn't work when I enter the IPort into my proxy list for firefox.
hoopsbwc34 said:
That's what I tried... but the IP address I get is 0.0.0.0 from your app. What IP do you usually get back when you run it? Do you just connect via USB? If ActiveSync is running is that an issue?
Click to expand...
Click to collapse
I am not sure why you are receiving 0 as your IP address. Check in Settings->Connections->USB to PC that "Enable advanced network functionality" is selected.
Gave it another try
Connected to ActiveSync (AS) loaded the application
removed the AS connection, started the application
It showed me the IP address op 127.0.0.1 (localhost)
Stopped the App, initiated the gprs and started the App again.
now i'm getting an IP of 0.0.0.0, I restarted the App a couple of times but no dice
I also checked if the advanced network functionality was enabled and it was..
Mr_Gee said:
Gave it another try
Connected to ActiveSync (AS) loaded the application
removed the AS connection, started the application
It showed me the IP address op 127.0.0.1 (localhost)
Stopped the App, initiated the gprs and started the App again.
now i'm getting an IP of 0.0.0.0, I restarted the App a couple of times but no dice
I also checked if the advanced network functionality was enabled and it was..
Click to expand...
Click to collapse
Hmm... I'm not sure what's going on here. 127.0.0.1 is the loopback interface-- It is only valid for your phone to connect to itself. If your computer attempted to connect to 127.0.0.1 it would connect to itself, not your phone.
pchasco said:
Hmm... I'm not sure what's going on here. 127.0.0.1 is the loopback interface-- It is only valid for your phone to connect to itself. If your computer attempted to connect to 127.0.0.1 it would connect to itself, not your phone.
Click to expand...
Click to collapse
Yes I know... :-/
Well, if I have time in the next few days I will take a look and see whether there is anything I can do. Maybe there is another IP address available on your device but for whatever reason I'm displaying the loopback instead of the external interface.
What happens when you set your proxy client up to go to 169.254.2.1:1080?
Mr_Gee said:
Gave it another try
Connected to ActiveSync (AS) loaded the application
removed the AS connection, started the application
It showed me the IP address op 127.0.0.1 (localhost)
Stopped the App, initiated the gprs and started the App again.
now i'm getting an IP of 0.0.0.0, I restarted the App a couple of times but no dice
I also checked if the advanced network functionality was enabled and it was..
Click to expand...
Click to collapse
Sounds like the same bug I am getting.
An example describing why someone would want to use it?
abdulzis said:
An example describing why someone would want to use it?
Click to expand...
Click to collapse
If you can't use ICS and want to connect to the internet from your desktop, you can connect your phone using USB and start this proxy, then you can setup your desktop connection to use the proxy to get internet access.

Any get VPN working with DCD 3.2.5?

Has anyone got VPN connectivity working with DCD 3.2.5? I have been trying for hours with no luck. Every time I try to connect I just get the generic unable to connect message (VPN Server problems. Verify your username and password..... I do know its not a user name / password issue. I set the VPN up and administer it. Its a ClarkConnect Community Edition Firewall Router 4.3.
I can however use the phone with Internet Sharing and connect to the same VPN end point with my laptop. I know the VPN is working.
Any one have any experience with this?
scrosler said:
Has anyone got VPN connectivity working with DCD 3.2.5? I have been trying for hours with no luck. Every time I try to connect I just get the generic unable to connect message (VPN Server problems. Verify your username and password..... I do know its not a user name / password issue. I set the VPN up and administer it. Its a ClarkConnect Community Edition Firewall Router 4.3.
I can however use the phone with Internet Sharing and connect to the same VPN end point with my laptop. I know the VPN is working.
Any one have any experience with this?
Click to expand...
Click to collapse
I'll be honest. I haven't really tried yet, but I am interested in getting this working myself, as I need to set it up; in addition to somehow getting this damn thing to connect to my school's network - which it has refused to for many weeks now.
scrosler said:
Has anyone got VPN connectivity working with DCD 3.2.5? I have been trying for hours with no luck. Every time I try to connect I just get the generic unable to connect message (VPN Server problems. Verify your username and password..... I do know its not a user name / password issue. I set the VPN up and administer it. Its a ClarkConnect Community Edition Firewall Router 4.3.
I can however use the phone with Internet Sharing and connect to the same VPN end point with my laptop. I know the VPN is working.
Any one have any experience with this?
Click to expand...
Click to collapse
Did you try using the kitchen and enabling the Enterprise IPSEC checkbox? It's the first item on the list. I assumed this was for those who needed VPN connections, so have not used it myself personally.
BTC
BillThyCat said:
Did you try using the kitchen and enabling the Enterprise IPSEC checkbox? It's the first item on the list. I assumed this was for those who needed VPN connections, so have not used it myself personally.
BTC
Click to expand...
Click to collapse
yep you need that for IPSEC vpn, but PPTP vpn would work without it.
BillThyCat said:
Did you try using the kitchen and enabling the Enterprise IPSEC checkbox? It's the first item on the list. I assumed this was for those who needed VPN connections, so have not used it myself personally.
BTC
Click to expand...
Click to collapse
Yes. Im going to flash back to a stock ROM later today and test.
I'll post the results.
DCD have you ever got PPTP to work?
scrosler said:
Yes. Im going to flash back to a stock ROM later today and test.
I'll post the results.
DCD have you ever got PPTP to work?
Click to expand...
Click to collapse
Telus ROM can authenticate just fine. Hmmmm. DCD Any thoughts?
PPTP VPN works
Here is what I did:
Configured the VPN connection.
Create a nework exception for a valid DNS name or use wildcards:
*.myvpnconnection.com
Anything you go to in that domain will use the VPN. IE seems to be the only thing that will initiate the connection.
It sounds like you might have something wrong on the server side.
MM
I just setup mine to use the vpn into my office and it worked slick as "stuff"... but we use a MS VPN server with AD...
I'm able to use VPN on 3.2.5 (stock, not cooked in kitchen) It works, but often time I have to soft reset before it will let me connect. Windows even suggests it... I haven't figured out a way around this when it happens, other then to soft reset.
Also I'm having a problem where VPN locks up the phone if I leave it connected, and the phone goes into lower power mode. It won't wake up with power. I have to soft reset.
Lastly, I'm trying to figure out the fastest way to actually launch the connection. It seems horribly buried / inefficent, the way I'm doing it:
I'm going to Start -> Settings -> Connections Tab -> Connections Icon -> Under the VPN Connection hitting "Manage Existing Connections -> VPN Tab -> Selecting the VPN Connection and "right clicking (hold until context menu pops up) and hitting "Connect".
Anyone know of a faster way?
Thanks in advance!!
PPTP and L2TP work fine here. I do have an issue where if I leave the connection live and the device goes to sleep it doesn't wake up and requires a soft reset. It's been like that for a number of revisions. Other than that it works fine.

[Q] Anyone get VPN Connections to work?

Hey guys,
I have been keeping my eyes out for the tun.ko module to come out in one of the kernels, and it finally did in the 1.76 GHz kernel. I had to reinstall VPN connections after flashing the kernel, and then VPN connections would tell me that my VPN was connected properly. However, I can't get data to pass through the VPN. No pings to the remote end, no RDP, nothing.
Anybody else get this working?
Thanks,
Seth
I thought I set up my VPN wrong >_> Well that explains it! Thanks! Same issue. I have however been able to see my phone in my router, though I can't do anything with it there in or out.
This sounds like the same issue I was having with openvpn (I assume that's what you're referring to since you're talking about the tun module). I'm running Das BAMF 1.3.2, and tun is already built into the kernel. I'm having the same problem. The VPN connects, no errors at all, even ran it in the terminal so I could see all of OpenVPN's connection output. But data is not routed through the tunnel. WhatIsMyIP still reports my Verizon IP address.
Now, on two occasions I have had success. I was able to connect and disconnect my VPN all I wanted and everything worked. However this only lasted for the current phone 'life cycle', ie it failed again after the next reboot. I can't find a pattern or anything, it seems that it will randomly work after a reboot, but not that often... 1 out of 10 maybe? I didn't waste my time trying to nail down a ghost.
I think I solved the OpenVPN problem. There's an option in OpenVPN settings called 'Fix HTC Routes'. If you check it, you can get the link to view the issue tracker. Essentially it deletes a few routing tables after OpenVPN starts up. For some reason, it doesn't seem to work on the Thunderbolt. Perhaps that option is using a deprecated script command (ip ru del route)? Whatever the reason, the fix is simple. After connecting to OpenVPN, open a terminal and issue the following commands:
Code:
ip ru del table gprs
ip ru del table wifi
Ignore any errors you might get if the routing table doesn't exist. I don't think you need SU, and you can use GScript Lite to make the process easier on you.
I'll give this a shot with VPN Connections when I get a chance and report back. If anybody else has any success, please post here.
I have had better success, but it's not right yet for me. I am able to get some data to flow using RDP, Telnet, etc., but nothing actually works completely right.
When telnetting into routers, I am not able to actually authenticate. however, I CAN finally see the prompts.
When using RDP, it doesn't time out any more, but I don't get any video data back to my phone's screen. No login page, etc.
Those two commands also seem to time out eventually. I need to reenter them to get the data flowing again, it seems.
Anybody else have better results?
Seth
Well, without knowing which VPN you're using, I can't say. But it does seem to work with openvpn and the OpenVPN Settings market app (I have my own install of openvpn, so I don't use the related OpenVPN Installer app).
The routing tables gprs/wifi are automatically recreated when those connections are re-established. Meaning, if you are on VPN via wifi, and wifi disconnects/reconnects, then the wifi routing table is recreated. The same goes for gprs if you lose connection and it is reestablished. I don't know what the system might try to do using the built in VPN connections.
Sorry about that, the lack of info wasn't very helpful.
I'm trying to connect to my Cisco VPN. We are using group authentication as well as user authentication. The outside device is a 2811 router, and if there are any other specifics that might help, I'd be happy to provide it.
Thanks,
Seth

[Q] OpenVPN Routing Problem

Hello
I have installed OpenVPN and its logging on to the vpn and is visible on the network list BUT I dont get any connection to another client in the vpn. I tried to ping another client from my SGS2 and from a client to the SGS2 but its always a timeout. I tried it with the phone and serveral wireless networks.
So I think it could be a routing issue but I dont have a clue how to see if thats really the problem and if its true how to fix it. I read some other posts and maybe it could also be a tun.ko problem but the SGS2 with 2.3.3 should already have installed it on the software, so I'm not sure how to see if thats ok. The Busybox is installed at /system/xbin. So does anybody have an idea how to find out whats actually the problem and how to fix this?
Thanks for your help!
Manolo
It's not clear to me if you tried connecting through your mobile data plan. Did you also tried that?
What is the IP that you are getting when your are connected to the VPN?
If it something like 192.168.1.* Then that's could be your problem. If the WIFI your are on, also gives you an ip adress as 192.168.1.* then that causes the problem. Either change the ip range of your network to 192.168.10* (just an example) or the ip range of you VPN.
ps can you post your VPN server settings?
Do you mean my own ip or the ip that i have in the vpn?
my own edge telekom ip is 10.219.127.35 and my internal vpn ip is 10.10.0.22
I can't post my vpn server settings because i got some key files for the vpn.
If you have installed installed this .zip
http://forum.xda-developers.com/showthread.php?p=16182571#post16182571
Then all you need to do is download openvpn settings from the market. And run in.
If you already did these steps, then the problem lies probably with your server and I need the server config. I don't need the keys of course
Thx!
How does this update work? I see no instructions on the post. Is it just to copy on the root folder?
Ah yes... I found how it goes and its working perfectly!
Thx a lot!

Categories

Resources