Did I just brick my GS2? - Galaxy S II Q&A, Help & Troubleshooting

Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o

---

SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
If it was bricked it wouldnt turn on even a bit. Just charge it or try changing the battery.

---

coolstorybro_123 said:
If it was bricked it wouldnt turn on even a bit. Just charge it or try changing the battery.
Click to expand...
Click to collapse
If I try to charge it it displays the SGS2 charging screen for a few seconds and then switcher straight off.
I just got into work and tried my colleagues 2000mah battery which had 32% in it. Exactly the same problem. WTF????
Thanks
Edit: FYI, it turns off before entering download mode or recovery. WTF????

---

Maybe you hit this ?

---

VAXXi said:
Maybe you hit this ?
Click to expand...
Click to collapse
That's just what I was thinking, actually
I couldn't find a description of what actually happens when this brick happens. The page doesn't really say... Does anywhere say?
Edit: I swear I didn't even flash the Siyah RC6 that was known to brick the phones either... -_-;;
Thanks!

---

It's not just a specific kernel, more are actually faulty. The whole story is here.

---

SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
your phone is ok as far as it shows u the s2 logo
you have 2 things to do , try to go to recovery or download mode and formate data/factory reset then flash another rom , btw what kernel u used before your phone go to this situation ? if you were using stable kernel "cm,neak,fluxi,syah stable" so you are safe from hardbrick bug , and the hard brick bug is done only if you have faulty kernel and wibed your data through recovery , and this isn't your situation , so don't be afraid

---

evaworld said:
your phone is ok as far as it shows u the s2 logo
you have 2 things to do , try to go to recovery or download mode and formate data/factory reset then flash another rom , btw what kernel u used before your phone go to this situation ? if you were using stable kernel "cm,neak,fluxi,syah stable" so you are safe from hardbrick bug , and the hard brick bug is done only if you have faulty kernel and wibed your data through recovery , and this isn't your situation , so don't be afraid
Click to expand...
Click to collapse
Thanks for saying, but I can't get into recovery or download. The phone switches off before then!
That's what's so confusing! xD
Thanks

---

With a known good batter try hard resetting to download mode 2x in a row.. Hold the button config to get into download mode.. Hold it through two restarts.. Might work.
Sent from my GT-I9100 using xda premium

---

I've nuked mine a few times with buggy kernels, sounds like a similar situation. I got my device back by flashing CM9 resurrection, then flashing Siyah, and finally from CWM flashing an ICS-based stock ROM.
I'd suggest taking a backup of your efs unless you're selling it with stock.
Sent from my GT-I9100 using XDA

---

SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
i am having exactly the same problem.i did a factory reset after flashing siyah kernel (SiyahKernel v3.3.1) on Resurrection remix v2.2.let me know if you guys find any solutions

---

JIG
try to use a download mode JIG.
I'm not sure if a link will violate xda-rules....
google it

---

dont worry
if you boot up and are getting the sg2 logo then you have not bricked you phone.
to fix simply download a .tar version of any rom and run odin to pda reinstall if you wanted to you could go the whole hog and reflash a fresh cf-kernal (rooted or stock) and then flash fresh firmware. just remember to get the kernal that originally matches the (ithink) your correct baseband ie xxki4
there should be no worries aslong as you dont pull the plug.
could have had a worse error saying installation incomplete please use kies then you would have to had taken battry out reinserted and hoped the three butn combo for rec. mode worked happened to me awhile back lol
hope i helped you
ps never read your post fully just skimmd the jist of it although the above should be applicable
also try resetting your battry stats in cwm

---

finally fixed
thanks for the help everyone.i have fixed it now.it seems like the problem was with the updated version of siyah kernel .i managed to put the phone in download mode.(kept the phone on the charger for a while. than, i don't know some how when i tried to go to download mode it did).and flashed siyah kanel v3.2.6.4 via odin