Ok here is what goes on with the phone... When its off and you connect the charger or usb data cable the phone wakes up and stays on the htc screen. The rainbow screen displays serial and not usb (even though I swapped the entire case from my wifes mozart phone, which did go to usb from serial in rainbow screen) so the port/ribbon cable cant be faulty. Tried hard reset with origanal 8gb card, tried 16gb card swap and hard reset too.
It goes into usb host mode when camera and volume down button and power buttons are pressed. So my question is this... I can buy a y cable debrand/flash from a well know auction site, but dont know if its a waste of £20? As my phone wont go from serial to usb in the rainbow screen I cant reflash/debrand, does the y cable debranding do the same thing as ansars rom install? Been trying for a week now.
Thanks all... just looking at the big pan spoon now, it will give it more than a scratch I can tell you, so expert replies only as outcome irreversible!
Related
Hi,
i have a NT , when i plug in the cable to my pc it shows he usual USB mode.
is there anyway to have it in usb mode but be able to use the tablet at the same time ? in other words get rid of the damn pop up and let me use it while its in usb and charging mode ?
thanks
you could try disabling automount... maybe the USB window is triggered when the SD is mounted for computer use.
That is absolutely correct. If you don't know where to find automount, it is accessible through the nt hidden settings app.
ive also been seeing a weird issue , ive done that in the past , but when my tablet is connected to power / computer usb cable to any power source my touch screen is funky , when im on the lock screen i can do stuff , i can pull the bar over to almost get it to unlock but when and if it does its funky , i just kicked it out off of auto mount and i have what i want except touch screen is not actually working , if i unplug it from the cable the screen works ,
any ideas ?
You could also try "ejecting" the device. That might put it in charge state and allow you to continue using the device.
spydergt said:
ive also been seeing a weird issue , ive done that in the past , but when my tablet is connected to power / computer usb cable to any power source my touch screen is funky , when im on the lock screen i can do stuff , i can pull the bar over to almost get it to unlock but when and if it does its funky , i just kicked it out off of auto mount and i have what i want except touch screen is not actually working , if i unplug it from the cable the screen works ,
any ideas ?
Click to expand...
Click to collapse
I haven't noticed the "funky" screen on my NT, but have experienced it on smartphones in the past and it was associated with a noisy charger. Try using different chargers and see if the problem gets better or worse.
ah yes you have a valid point i have two NT's one for me and one for my gf hers blew a charger and we had to have B&N replace the usb port receptacle already , had it less than three weeks. I will try it with her usb cable and see what i get as they changed the whole assembly and if it does not occur with her new cable i will get them to exchange it before the 1st ..
I managed to soft brick my wife's Vibrant while trying to put it back to stock ROM: basically I get the "Phone -- Yellow exclmation -- PC". The volume up, down and power combo doesn't work.
In addition, to make things worse, if I plug it into the PC it gets power but the PC doesn't recognize the USB, so I can't use any type of soft unbrick software.
Should I give a try to the USB jig to get into download mode or, do you guys think the USB port is faulty... I know it's kind of hard to know, but I'm primarily curious to see if anyone got in a similar situation with soft brick and no USB connectivity and was able to solve it with the jig...
Thanks!!!!
ZetaTre said:
I managed to soft brick my wife's Vibrant while trying to put it back to stock ROM: basically I get the "Phone -- Yellow exclmation -- PC". The volume up, down and power combo doesn't work.
In addition, to make things worse, if I plug it into the PC it gets power but the PC doesn't recognize the USB, so I can't use any type of soft unbrick software.
Should I give a try to the USB jig to get into download mode or, do you guys think the USB port is faulty... I know it's kind of hard to know, but I'm primarily curious to see if anyone got in a similar situation with soft brick and no USB connectivity and was able to solve it with the jig...
Thanks!!!!
Click to expand...
Click to collapse
I'm not sure ajig would help you but its good to have ajig laying around just in case things go bad. The jig will get you into download mode but if your usb cable/usb port is bad then you still can't connect to your pc to use odin. Sounds like you need a new usb cable or you need to clean your usb port. Have you tried cleaning your phones usb port with isopropyl alcohol and a Qtip? We had a member fix his phone this way just yesterday. If that doesn't work and a tmobile usb cable doesn't work then you might have a faulty usb port. Tmobile has a 30 day money back guarantee on the usb cable so try that if you haven't already. If you end up exhausting all options then I recommend www.mobiletechvideos.com to replace your usb port, plenty of folks have had success with them in the past. Just so you know, the only usb cable that works for me is the one from the tmobile store. I'm not sure why but I have three other cables that work fine on my friends vibrant but dont even do anything at all when plugged in to my phone (not even charge). Let us know what ends up being the fix, good luck.
Sent from my SGH-T959 using xda premium
I gave it a try and cleaned out the USB port with some electronic contact cleaner, but that didn't help. I've also tried 4 cables and 2 PC with no differences.
I'll try out the JIG and see if that fixes it if not I'll decide what to do:quite frankly I would unbrick it and bring it back to the stock firmware just to turn around and put it on eBay, so I'm not quite sure it's worth the effort... But since I've already ordered the JIG I'll give that one a try...
Good luck. I suggest you mod your phone like mobile tech videos (tried acronyming it to MTV but you know) did to make it unbrickable.
Sent from my SGH-T959 using xda app-developers app
ZetaTre said:
I managed to soft brick my wife's Vibrant while trying to put it back to stock ROM: basically I get the "Phone -- Yellow exclmation -- PC". The volume up, down and power combo doesn't work.
In addition, to make things worse, if I plug it into the PC it gets power but the PC doesn't recognize the USB, so I can't use any type of soft unbrick software.
Should I give a try to the USB jig to get into download mode or, do you guys think the USB port is faulty... I know it's kind of hard to know, but I'm primarily curious to see if anyone got in a similar situation with soft brick and no USB connectivity and was able to solve it with the jig...
Thanks!!!!
Click to expand...
Click to collapse
It gets power.does it means your wife's ph is charging??try charging battery with external charger..and connect to pc...
Sent from my MT11i using xda app-developers app
If you happen to have Amazon Prime, you can get a jig from Amazon in your hands with next day delivery for $8 (3.99 for the jig and 3.99 for the delivery).
Now that said, if you happend to have flashed the GB bootloader at some point, rememer that the download mode is now accessed by the volume up, instead of both up and down. It's definitely worth giving this a try:
- take out the battery
- plug in the usb to the phone and your PC
- hold the power up button and insert the battery. It should go right into download mode
I actually did have a GB room installed... I'll give it a try tonight: thanks for the heads up!!!!
Just noticed that you said you already ordered the jig so NM about the amazon suggestion. I've been in the situation with the exclamation point and thought mine was bricked. I ordered the jig on Amazon and then finally tried what I detailed above and got in download mode. I could not get in DL mode no matter what else I tried, including just powering up with USB attached and volume up held. I had to do it with the battery being inserted with volume up.
Good luck and remember, the jig may work for the phone, but flowers usually work for the wife.
It was indeed the wrong combo to get it into download mode: using the volume up only and it went right in. The USB connectivity is also solved.
After some back and forth I was able to get CM 7.2 loaded and it works perfectly. Now I just need to solve the dreaded GPS issues of this phone: tonight I'll take it apart and see if bending the antenna connector solves it. It is a August 2010 production so it might as well be.
Other than that CM7.2 works pretty damn good. I already have it on my N1 with no issues. The Vibrant is very much snappier now, particularly if you crank it over to 1.3GHz.
Again thanks a lot for all the help!!!!
A friend had the same problem where it wouldn't go into download mode and would just stay at the phone ! computer screen. It would auto turn on when plugged into usb to this screen so that gave me little hope. What I ended up doing was holding all three buttons and when it turned black let go off power but kept volumes held, it would load back to the exclamation screen and I would hold the power button again, it cycled like this 3 or 4 times, but eventually went back to the download mode and I was able to restore with Odin.
So I fell on the ground with the phone hanging on a neckband around my neck at the time of the fall; screen is busted... Let me remind you phone was NOT rooted yet (I bought it the night before, didn't get to it YET), with a trick found on YouTUBE connecting an OTG USB adapter to the phone and connecting any USB mouse to this OTG adapter, then this broken screen will have a little cursor/arrow light up;
Obviously, after that you can do whatever with a cursor coming up on this broken screen and with normal clicks you are all set...
But now is another problem......
In order for me to be able to take a full backup of that broken LG and to be able to load it on to this one, I would need to have the phone ALSO plugged in with my PC at one point of time.... now here is a dilemma... mouse is already there.
And I’m %100 sure that there has to be a workaround for this situation. Maybe there is an app in store that can do this for you? I can’t be the first to bust my screen, right?
Can't find a link for my G3, but this very simular. http://podfob.com/products/samsung-galaxy-s6-podfob
Thanx folks
P.S. Later tonight I'll be getting my new LG replacment phone. So please, give me your advice??
Hi,
My brother dropped his Archos Diamond in a bath...
The screen doesn't work but when I power on the phone, it vibrates.
I'm not sure it's the screen so I don't want to buy a 50$ screen for nothing
Because maybe it's the screen connector, or another component before that.
I entierly disassembled the phone, but nothing looks bad.
It seems I can't use Android Control to see the phone screen on PC
Because he didn't enabled USB debugging, except if I can flash it with a rom that has it enabled but I don't know where to find that.
Is it possible to connect a screen not made for this phone if it has the same connector ? Are LCD connectors standard ?
Any ideas ?
Hi,
Please, be patient while reading this post, this is a looong explanation of the brick I am facing...
I recently was given a non working XTZ SGP311 and tried to get it back to life. As I have another one SGP311 (this one is perfectly working), I am able to check many things.
I read most of topics about XTZ unbrick but can't find any way to get it back working.
The problem is that I can't have any signal from usb (data or power). I use a genuine Sony USB cable and genuine Sony charging adapter (coming from the working SGP311). The led always stays off.
I tried the different combos as described (vol- and power ; vol+ and power ; vol+ and vol- and power) during 5, 10, 20, 30 seconds (yes, quite complete tests).
I did a cross check of batteries and inside usb connector ribbon (yes, had to open both tablets for that), the working tablet continues to work with the 2 parts coming from the faulty one (battery coming from dead tablet was 0% charged), so the problem is not on the side of the inside usb connector neither on the side of a supposed dead battery. The faulty tablet doesn't boot, even with a fully charged battery inside.
I luckily own a XTZ dock (SGPDS5) that allows to charge without using usb connector (it uses the 2 contacts located on the left side of the tablet). That's the only way to get something...
Soooo, when I put the bricked tablet on its dock, the red led flashes very slowy (say, 1 second off, 1 second on red, and so on).
When I press vol- and power, nothing happens (no matter 5/10/15/20/25 seconds).
When I press vol- and vol+ and power, idem.
When I press vol+ and power : I got the sequence blinks once white led / blinks 3 times white led (after that goes to slow red blinking about if I keep the keys pressed). So not completely dead.
If I unplug it from the dock right after the third white blink, plug the usb cable to the tablet, plug it to my laptop (with emma running, tried with pc companion too), and press vol-, then....nothing happens. Really nothing. No led lit. No detection of anything from the laptop (or device manager as well). It would have been the same if I would have kept it unplugged.
To sum it up, the only thing I can have is 1 or 3 white blinks after having plugged the SGP311 on its docks.
IMO, the trouble comes from a faulty component inside the tablet. Maybe the one that manages the connection from the usb ribbon plug. I checked the tiny plugs inside the tablet (once dismantled and back repacked too), all seems in order.
Your help is welcome !
This is similar to an issue I have it sounds like, you can still flash stock rom by holding power + volume till it blinks 3x then plug USB in and hold volume down immediately.
This gives flash mode, you can use flash tool to put stock rom on with this. The issue happens when it's acting like there's no OS it seems. Problem is mines doing this everytime I flash a custom rom, it's fine with stock aside from **** wifi
Thanks for your help. I tried that yesterday and it did not work.
This may be related to the way of reset I use (but I can't have any other).
As I can't get any white blinking led when connected by the tablet micro-usb port, the one and only way to get the 3 times white blinking led is when the XTZ is on its dock (SGP DS5, power connection only by lateral contacts).
What I tried yesterday was to get the 3 time white blinking led (vol+ and Power), then output the tablet off the dock and connect a usb cable to a laptop running Sony Emma (from micro usb tablet port to usb laptop).
Precision : I kept VOL- pressed when pluging usb cable to laptop.
No result at all. No detection (either Emma nor windows).
Any idea ?
jzk01 said:
Thanks for your help. I tried that yesterday and it did not work.
This may be related to the way of reset I use (but I can't have any other).
As I can't get any white blinking led when connected by the tablet micro-usb port, the one and only way to get the 3 times white blinking led is when the XTZ is on its dock (SGP DS5, power connection only by lateral contacts).
What I tried yesterday was to get the 3 time white blinking led (vol+ and Power), then output the tablet off the dock and connect a usb cable to a laptop running Sony Emma (from micro usb tablet port to usb laptop).
Precision : I kept VOL- pressed when pluging usb cable to laptop.
No result at all. No detection (either Emma nor windows).
Any idea ?
Click to expand...
Click to collapse
let it charge for a night period. Then try to flash again.
Rootk1t said:
let it charge for a night period. Then try to flash again.
Click to expand...
Click to collapse
Thanks for your advice, I appreciate.
But I swapped batteries from the working XTZ to the non-working one and put a (about) 60% charged battery into the bricked XTZ (both batteries are charging when set into the working XTZ). I will try anyway.
The problem is that the non working XTZ does not charge either through usb or through the dock. The only interest of the dock is that this is only situation where I can have the "triple white led blink" (but nothing more).
That's why I need the working XTZ for charging before doing anything with the non working one.
What I could try would be to connect the lateral contacts with wires to the dock in order to keep an access to the usb tablet micro port and connect it to a laptop.
But this may be hairy as this would give 2 ways for power (one by the dock and the other by the USB port), and may produce a short circuit...
Any XTZ power experts around ?
Hello, Did you find a solution to this issue ?
Hello, did you find a solution for this issue ? Look like that I had the same.
jzk01 said:
Thanks for your advice, I appreciate.
But I swapped batteries from the working XTZ to the non-working one and put a (about) 60% charged battery into the bricked XTZ (both batteries are charging when set into the working XTZ). I will try anyway.
The problem is that the non working XTZ does not charge either through usb or through the dock. The only interest of the dock is that this is only situation where I can have the "triple white led blink" (but nothing more).
That's why I need the working XTZ for charging before doing anything with the non working one.
What I could try would be to connect the lateral contacts with wires to the dock in order to keep an access to the usb tablet micro port and connect it to a laptop.
But this may be hairy as this would give 2 ways for power (one by the dock and the other by the USB port), and may produce a short circuit...
Any XTZ power experts around ?
Click to expand...
Click to collapse
Canhobix said:
Hello, did you find a solution for this issue ? Look like that I had the same.
Click to expand...
Click to collapse
Well, not a real solution...
I bought a cheap xtz with broken screen and got its working motherboard and put it instead of the other one.I got the lte component too with its antenna and put it into the 1st xtz that was not supposed to have lte.
So now, on one side I have a xtz with faulty motherboard and broken screen, and on the other side a refurbished xtz with LTE !
I like very much this tablet. Very handy, easy to dismantle and easy to swap its components.
The only drawback is no more support for Sony.
Thank you for the answer
So, you are saying that if I replace the motherboard I can fix that ? I'm looking for motherboard on ebay and I found one for $28 usd + shihpping.
Thank you for answering and take care.
jzk01 said:
Well, not a real solution...
I bought a cheap xtz with broken screen and got its working motherboard and put it instead of the other one.I got the lte component too with its antenna and put it into the 1st xtz that was not supposed to have lte.
So now, on one side I have a xtz with faulty motherboard and broken screen, and on the other side a refurbished xtz with LTE !
I like very much this tablet. Very handy, easy to dismantle and easy to swap its components.
The only drawback is no more support for Sony.
Click to expand...
Click to collapse
Canhobix said:
So, you are saying that if I replace the motherboard I can fix that ? I'm looking for motherboard on ebay and I found one for $28 usd + shihpping.
Thank you for answering and take care.
Click to expand...
Click to collapse
Yes. I think this should be good.
Don't care about the exact matching of the product code: as long as it'll be xtz, it'll be good (16 or 32 gb, with or without lte, and any region should match).
Did you opened it already ?
Yes, I opened 2 years ago cuz my son broke the power jack connector then I replaced that twice.
I'm also tech guy, I can replace that, but won't expend more than $50 for a new motherboard. I'm looking on ebay now.
Thank you
jzk01 said:
Yes. I think this should be good.
Don't care about the exact matching of the product code: as long as it'll be xtz, it'll be good (16 or 32 gb, with or without lte, and any region should match).
Did you opened it already ?
Click to expand...
Click to collapse