I recently purchased Mercury Leather Wallet Case from ebay (Link).
I bought a no-name leather flip case from a local shop (I tried to find the same one on ebay for reference, but failed), and it was very nice case. Good quality leather with little padding. BUT, it didn't have any protection at the top and bottom of the phone. And more importantly, there was a magnet behind the phone on the right side, which interfered with s-pen operation. I started taking out the phone whenever I was home, and then I decided to get a new case.
After searching through sites and ebay, I found this Mercury case. I chose this one because the phone was detachable with a jelly case.
First, the case is not as nice as it looks on the photo. It is not real leather, more like plastic and thin. Stitching is well-done for the most part, but it could be better. The magnet closure is using glue and it is already coming apart. I will have to superglue it or tape it up. It can hold up to 4 credit cards, but it barely closes.
The best part of this case is the jelly case. It is better quality than the usual TPU case. It is slippery to slide in and out of my pockets, but provides good grip in my hands. The phone wiggles just slightly in the jelly case, but a very good fit. On the leather case, there is a silicon-based sticky pad, where the jelly case sticks onto. I have had the jelly case on and off multiple times, but it still holds the case very nicely. If I needed to, I can wipe it with a wet towel to clean it.
And here is the second issue. The cutout for camera/speaker/s-pen is slightly out of alignment. If I align the phone to the cutout, outside edge of the phone is at a slight angle from the leather case. If I align the phone to the outside edge of the leather case, camera is off to the side of cutout. It doesn't affect the camera operation, but it is an issue nonetheless.
For the price, I think it is a very good value, because you also get a very good quality jelly case. When I go out, I stick the phone into the flip case. When I am the office or home, I take it out for easy access to the phone.
Oh, it also came with a screen protector, but I already have one on, so I don't know what it is like.
http://www.spigen.com/cell-phone/sa...laxy-note-at-t-case-ultra-capsule-series.html
I just learned that the jelly case included in Mercury Wallet case is exactly the same material as SGP Ultra Capsule Series. I had them side-by-side.
They both seem to be from Korea, so these cases may just have different branding.
Related
Hi all,
Here is my review of the Sikai leather/plastic case, as sold by Amazon. For comparison, I have had my Prime in the Poetic cover since I got it. It was okay, but didn't have a charging slot in the spine so it had to be open to be plugged in - plus the nearly-flat angle was nearly-useless because the cover kept slipping out of the tab you tucked it into. I had ordered the GreatShield folio case, but returned it because I didn't like the way the case gripped the tablet, plus I didn't like that to close the cover I had to put pressure on the screen to slide the clip past the edge.
Onto my review...
As mentioned in other reviews, it is a strange mix of black leatherette and dark brown plastic. The plastic back plate is great - the Prime snaps in and seems to be held quite securely. Similar to many iPad covers, it just wraps over the edge - enough to hold, but out-of-the-way enough to really reveal the sleek Prime look. The main portion of the back plate is the black leatherette material, with only the outer edge showing the brown plastic. It has all of the necessary cutouts - including (apparently) the ability to have the dock attached and still close the cover. That is because the "hinge" pieces that connect the cover to the back plate are elastic. I don't have a dock, so I can't comment much on that.
The leather-ish cover looks to be two pieces glued/sewn together, with two bends in the midde - allowing it to be folded up in a triangle shape. Both angles I tried seem to be reasonably stable while typing. About the two layers of the cover...they might have been able to get away with only one, giving it a sleeker appearance, but they had to account for the strap that slips over the sides to hold the cover against the screen. The strap is fine, and gives it an upscale look, but I would have preferred a more unobtrusive solution with magnets or something similar. Overall, the case is skinny enough - just about the same thickness as my Poetic case. That is actually a bit of a downer since I expected this to be thinner since the Poetic case has that layer around the bezel with the magnets in the corners.
There are a few tiny fit-and-finish things that I didn't expect to see in a $30 case. The leather part of the back plate doesn't always make a perfect fit with the plastic border. I'm really nitpicking here, but when this costs three times as much as my Poetic case, I was expecting Ferrarri-quality stuff. I know - it still only $30 so I won't beat them up (much) for it.
Overall, I really like the Sikai. It has a superior look to the Poetic - that one hid all of the nice features of the Prime underneath the protective layers of the front/back/cover. When all that is exposed is the center part of the screen, it almost doesn't matter anymore what Asus designed it to look like. The Sikai shows the Prime's lines and curves much better than the other cases I have seen. The plastic seems tough enough to not break or wear any time soon, so as long as the leatherette holds up, I say this is the best case available for the Prime under $30...
By the way, when ordering from Amazon, it ships from Hong Kong. I placed the order on June 18th, and got a confirmation within 24 hours that it had shipped. However, the confirmation email said my ETA was JULY 31st! Needless to say, I was very happy when it arrived today instead...
I figured there were already better pictures available than my crappy phone can provide, but I can take some close-ups of specific features if requested.
Thanks!
swordsman74 said:
It has all of the necessary cutouts - including (apparently) the ability to have the dock attached and still close the cover. That is because the "hinge" pieces that connect the cover to the back plate are elastic. I don't have a dock, so I can't comment much on that.
Click to expand...
Click to collapse
The dock works great with this case!
yeah I've had this case for a few weeks and its very functional. I really like how it doesn't cover the bezel on the prime like the sikai fiber case and you get multiple angles that actually work
My only complaints are that its a bit on the heavy side and because its designed to be put into the dock with the case on, the steepest angle isn't quite as steep as other cases because the flap slides out making the "hinge" not at the fold but an inch out
oh and the case is kind of ugly haha
I'm not usually one to use a cases on my electronic devices. I like my phones like I like my women, naked with a nice screen protector.
But since the G3 seems to be made of some of the most slippery plastic I've ever held, I dropped it a few feet the other day and slightly nicked the corner of it. So I'm looking for a very simple case, but as I said in the title, I'm picky.
It doesn't need to protect it all that much, but one thing I can't stand is when the case comes up over the edge of the screen. I'll use an example of a case that someone posted on the "Show us your case" thread:
http://forum.xda-developers.com/attachment.php?attachmentid=3337032&d=1432863723
See that slight "rim" around the edge of the bezel? It bothers me, which is why the two cases I've already bought are sitting at home unused. I need it to be flush, or even recessed from the front of the phone.
Does anyone know of a fairly basic case that won't have anything protruding up around the edges of the screen? I'd love one of those official replacement back cases from LG, but they're apparently extremely rare. So other options would be great.
Thanks!
If you dislike cases why not just get a full body clear skin from Skinomi or Bodyguardz? I'd recommend the LG Slim Guard Case. It has a raised lip but is super minimal, almost flush with the screen. This case unlike other thin G3 cases offers full body coverage/protection. LG also has the Slim Hard Case however this case does not offer fully cover the phone. The Ringke Slim is another good case option. It does have a small lip. Check ebay for the OEM cases if you can't find them on Expansys
Just received this case in the mail today and had to get some pics of it right away. This is a very well made case. It is a TPU case with a hard plastic cover attached to the back of it. It has a nicely textured design on the back. The sides have a bit of a recess to make it easy to grip and good protection at the corners. All cutouts on top, bottom, and for camera are perfect. The hard plastic back has a slightly raised X shape for better strength. The case works great with the film screen protector that I am using. This case has a pretty square shape on the back sides, it doesn't show the tapered side edges of the phone do to how it's made. The inside is fitted to the edges though. When the phone is resting on the back you can make it wobble, this is do to the raised Poetic "P" emblem that is raised. My Samsung wireless fast charger works well with this case too.The Poetic brand of cases seem to be very well made, with what appears to be great protection in thinner designs, while being stylish and a decent price. This is my second Poetic case as I have their Affinity also.
Hey guys, back again with a highly requested review from my previous threads!
I received both the Fusion Bumper case and the Slim Stand case from orzly the other day, and I really like them so far!
Fusion Bumper Case
The Fusion Bumper is one of Orzly's high end case, and it has become one of my favourite cases for the OnePlus 5 so far. It is as the name replies, A fusion Bumper aka a mix of a bumper case and a regular case.
The sides of the case are made of Rubber, which slightly wrap around the back. This, paired with the dotted sides where your hands rest allow for great grip and protection. The rubber is tough and after a few drop tests is still in great condition. The back is made of a clear plastic, but it isn't a gel type plastic it is the type which doesn't yellow, similar to the one used on last years OnePlus 3 fusion bumper which hasn't yellowed for me yet.
The back corners of the device feature little raised points, which not only helps keep the camera off of the tables, but it also allows for the clear black plastic to stay away from surfaces as to not get scratched up. There is a nice lip around the front of the screen, and all my ports line up. The dash cable and my aux cable still fit into the ports nicely, and none of the microphone holes are covered up.
On the volume buttons and power button there is the + and - symbols, along with the power symbol which I like as it shows attention to detail. Orzly also split the volume up and down keys to make it easier to diffrentiate them.
So far, I don't have a fault with this case. It does exactly what I need it to do, is protective, feels like high quality and has a clear back that won't yellow easily. Its grip is great as I won't drop it when taking pictures anymore. If any faults do pop up, I will be sure to update the thread . Pictures of the case can be found below!
http://imgur.com/a/wxLAi
Slim Stand Case
Now this is a slightly different case for a different sort of person. I used this case for about 8 days straight so I think I have a pretty good idea about it. It wouldn't be my sort of case, but I can see the use cases for it!
First off, the material on the slim stand case is really nice. Its sort of a soft touch rubbery feeling which provides a lot of grip. At the top and bottom there are antenna lines which mimic the ones of the OnePlus 5 design so it made my phone look like a midnight black version which was awesome!
The ports all line up nicely, and the little ring at the back rotates to allow for vertical or horizontal viewing when up which I thought was very useful. The ring can also be used while you are using the phone or taking a call and helps to make sure you won't drop the device! As the name implies, it is a slim case and it means it. It feels like (besides the stand) like there is not case on which is great!
As for protection, this case really only offers back protection rather then screen protection. Because it is a slim case the lip around the screen is minimal if not none and if you are looking for protection, this isn't for you.
I can see this case being useful for people who sit at a desk all day or go on train/plane journeys a lot as you could just easily access your screen. However it isn't the case for me as I prefer protection rather then slimness. I didn't really like how much the stand part stood out at the back when it was lying flat on a table as it made it not steady and rocked. However thats part of the parcel, and like the wallet case this is definitely for a certain group of people!
Links to amazon cases:
Fusion Bumper Case
Slim Stand Case
Do you recommend buying the orzly fusion bumper case for 10$ here in india :0 i m quite perplexed what to get, as i gonna use a skin and i want a clear bumper case too.
Hey everyone,
Since I typically use a flip case (a regular case with a protective cover for the screen that flips open) with all the phones I've owned, I thought I'd open a thread to start a discussion about people's experiences and recommendations with flip cases for the 6T.
Share something and help someone with what product to use!
Reserved
I'm currently using this one:
Foluu Compatible OnePlus 6T Case,... https://www.amazon.com/dp/B07K2S5DFC?ref=yo_pop_ma_swf
Pros:
+ magnetic edge on flip cover afixes the flip cover to the back, neatly preventing flapping
+ the sides of the phone are completely covered by a transparent bumper, with cutouts only for usb, alert slider, and speakers
+ relatively screen protector friendly
Cons:
- not a smart cover
- back cover is not a single piece with the sides, adding to bulk
Again, the pro/con list reflects my personal preferences and of course, may not apply at all to you.
Orzly Wallet Flip Case looks decent enough. I am currently using the oneplus 6t flip case with card slot, and its okay. Doesnt flap much, but it does not compare to my last otterbox strada case for the iphone 8 plus. Still looking for something similar.
I've also purchased some ringke 3m card slots, both the plastic and the nylon to add to the tpu cover that was included with the phone. Although not a flipcase, the downside with not having a solid magnet or full edge protection gives higher probability of the phone landing face down when dropped.
Exholeus said:
Orzly Wallet Flip Case looks decent enough. I am currently using the oneplus 6t flip case with card slot, and its okay. Doesnt flap much, but it does not compare to my last otterbox strada case for the iphone 8 plus. Still looking for something similar.
I've also purchased some ringke 3m card slots, both the plastic and the nylon to add to the tpu cover that was included with the phone. Although not a flipcase, the downside with not having a solid magnet or full edge protection gives higher probability of the phone landing face down when dropped.
Click to expand...
Click to collapse
I second the motion -- the Otterbox Strada on my Samsung S7 Edge is the gold standard for me. Most expensive case I've bought but has lasted many multiples longer than any other case. It's still a tank and still in use nearly three years later.
Closest case for OnePlus to that standard was the Tech21 flip case for my 6. Don't think they make it for the 6T though.
I'm using the flip case that I got from OnePlus when it's working fine.I've had better and I've had worse but pretty good I'm happy. No issues,, thinking about getting a OtterBox when they come out just for safety. But they're so big and bulky and ugly.,,,,,,,, I guess we'll see
I like cases.
My wife thinks that I have a fetish for phone cases.
I change them when I go out depending on what I feel like.
Here are the flip cases that I have purchased so far;
https://www.ebay.ca/itm/For-OnePlus...var=472229251615&_trksid=p2060353.m2749.l2649
The traditional brown leather flip case.
https://www.ebay.ca/itm/For-OnePlus...var=591631248320&_trksid=p2060353.m2749.l2649
Dr. Who TARDIS because....every phone needs to be inside a Tardis...
https://www.ebay.ca/itm/For-OnePlus...var=572979395291&_trksid=p2060353.m2749.l2649
Blue leather scroll work for when I'm feeling like Jazz.
https://www.ebay.ca/itm/PIN-1-Art-C...var=472327549790&_trksid=p2060353.m2749.l2649
Old School fun right here... I have purchased so many freaking cassettes over the years.. ugh. Why not put my phone in one...
I chose the white and green tape.
https://ca.mobilefun.com/olixar-xtome-leather-style-oneplus-6t-book-case-brown-70015
Old brown leather bound book.
I think that this book one will be my favorite flip case.
Only the Cassette tape case has come in so far.
It's a bit larger then a real cassette tape and it's a big large for the phone.
Then I've purchased another half dozen or so hard cover cases/non flip.
geeksquad2 said:
I like cases.
My wife thinks that I have a fetish for phone cases.
I change them when I go out depending on what I feel like.
Here are the flip cases that I have purchased so far;
https://www.ebay.ca/itm/For-OnePlus...var=472229251615&_trksid=p2060353.m2749.l2649
The traditional brown leather flip case.
https://www.ebay.ca/itm/For-OnePlus...var=591631248320&_trksid=p2060353.m2749.l2649
Dr. Who TARDIS because....every phone needs to be inside a Tardis...
https://www.ebay.ca/itm/For-OnePlus...var=572979395291&_trksid=p2060353.m2749.l2649
Blue leather scroll work for when I'm feeling like Jazz.
https://www.ebay.ca/itm/PIN-1-Art-C...var=472327549790&_trksid=p2060353.m2749.l2649
Old School fun right here... I have purchased so many freaking cassettes over the years.. ugh. Why not put my phone in one...
I chose the white and green tape.
https://ca.mobilefun.com/olixar-xtome-leather-style-oneplus-6t-book-case-brown-70015
Old brown leather bound book.
I think that this book one will be my favorite flip case.
Only the Cassette tape case has come in so far.
It's a bit larger then a real cassette tape and it's a big large for the phone.
Then I've purchased another half dozen or so hard cover cases/non flip.
Click to expand...
Click to collapse
Damn, your wife's probably right..!
But it could be worse: you could have a phone fetish instead of a phone case fetish, and that would be much more expensive.
The flip cases that I have ordered so far have come in.
Also, two of the hard cases have arrived as well. (As an aside, I don't like any of those yet. We will see if the rest of the hard cases are any better)
I like the oneplus oem flip case because it is the only one that has a magnetic feature that turns the screen on and off.
That is nice.
But I find it too small and it doesn't offer much protection.
And it only has one debit card slot.
Not useful as a wallet.
The oneplus, cassette tape and book flip cases do not have a magnetic clasp to keep them closed.
I kind of like that feature.
It gives me a fidget to play with.
And it makes it more noticeable if someone opens the case to take my debit card? Dunno.
Lol
Taking a look at the back side of these cases, some of them are not like the others.
Some of the cutouts look off.
I haven't checked them to see if it affects function or not.
Honestly I don't use the camera much anyways.
If anyone has any questions about these cases, let me know and I will do my best to answer them.
If anyone has a suggestion of another flip case for me to try out, then I am all ears!
P.S. And yes. The book is my favorite case so far. Followed by the Tardis.
Hi, I am looking for the same, but it is so hard... I know exactly what I want but all of the good looking cases are plastic inside and all the silicone ones are not-so-good looking.
Anyone found so far a sleek and elegand flip case with silicone inside?