Someone help me please, I was trying to re-lock the boot loader on my xperia s with flashtool 0.8.6.0 folowing the guide on here and now I'm stuck in flashmode I've tried a hard reset, flashing stock ftf and nothing's working flashtool just say's --flashing finished
-please wait phone will reboot
-for flashtool unknown sources and debugging must be checked in the phone settings
-device connected in flashmode
I really hope the phone is not bricked any help very much appreciated guys
Simon
super hans said:
Someone help me please, I was trying to re-lock the boot loader on my xperia s with flashtool 0.8.6.0 folowing the guide on here and now I'm stuck in flashmode I've tried a hard reset, flashing stock ftf and nothing's working flashtool just say's --flashing finished
-please wait phone will reboot
-for flashtool unknown sources and debugging must be checked in the phone settings
-device connected in flashmode
I really hope the phone is not bricked any help very much appreciated guys
Simon
Click to expand...
Click to collapse
Did you try to post in the same thread you got the instruction?
So have unplug the device but the LED green light is on? the Vol+ & power together till three vibrates didn't work?
Yes thats right if i unplug the device the LED goes out but when i push the power button it just flashes green and nothing happens, I've tried the volume up + power it vibrates 3 times like normal but when i push the power button the same happens green LED flash
no I haven't tried that I'll post it in there now cheers for the advice
flash the firmware again, and when you plug in the phone, hold the volume down button only, you dont have to hold the power one, it should go into flash mode now
super hans said:
Yes thats right if i unplug the device the LED goes out but when i push the power button it just flashes green and nothing happens, I've tried the volume up + power it vibrates 3 times like normal but when i push the power button the same happens green LED flash
no I haven't tried that I'll post it in there now cheers for the advice
Click to expand...
Click to collapse
unplug the cable from your phone, then hold the vol + and power till vibrates three times. now your phone is off,
lunch flashtool and initiate the flashing process with ICS firmware and hold vol - and plug the phone in, see if that works.
Sony developer on the forum believe that no one could hardly brick a Sony phone.
it wont let me flash ftf as it keeps dropping out of flashmode then re entering it flashtool is saying
-ERROR flashing aborted
-device disconnected
-device connected in flashmode
over and over again, I can get it into fastboot mode is there anyway I can re flash ftf in fastboot through cmd?
I think the battery might be dead now when I connect it all i get is a red LED
Hello!
It appears I have the same issue with xperia pro. After flashing the official 4.0.4 rom with flashtool the log says:
Code:
27/032/2012 15:32:18 - INFO - Flashing finished.
27/032/2012 15:32:18 - INFO - Please wait. Phone will reboot
27/032/2012 15:32:18 - INFO - For flashtool, Unknown Sources and Debugging must be checked in phone settings
27/032/2012 15:32:18 - INFO - Device connected in flash mode
The phone doesn't respond, the green led is on.
Have you been able to restore the phone functioning?
---------- Post added at 02:56 PM ---------- Previous post was at 02:40 PM ----------
Ah, it's okay. I re-flashed the phone with a different rom and now it is working fine.
Hi.
I had a similar issue on a Xperia Play. Try this: http://forum.xda-developers.com/showthread.php?t=1126358
relocked bootloader trough flashtool to see if i could get bravia engine 2 working and now my phone won't start, just vibrates one time and green led light and thats it.
help please!!!!!
hackerpower said:
relocked bootloader trough flashtool to see if i could get bravia engine 2 working and now my phone won't start, just vibrates one time and green led light and thats it.
help please!!!!!
Click to expand...
Click to collapse
try to flash a new stock rom.
my phone stucked on flash mode and the problem is i cant get it on like usual.. im using xperia u.. and before flashing i forgot to enable usb debuging and now its stuck on flash mode!
HELP
Ali Suhaimi said:
my phone stucked on flash mode and the problem is i cant get it on like usual.. im using xperia u.. and before flashing i forgot to enable usb debuging and now its stuck on flash mode!
HELP
Click to expand...
Click to collapse
Calm down dude. Grab flashtool. Set flashmode and choose your stock ROM. And just flash it through vol down key and plug in USB to your phone. It is just a soft-brick. No need to worry much.
Sent from my ST25i using Tapatalk 2
the problem is i didnt enable my usb debugging before that so when i connect to laptop its says that the device malfunctioned.. so what to do??
Ali Suhaimi said:
the problem is i didnt enable my usb debugging before that so when i connect to laptop its says that the device malfunctioned.. so what to do??
Click to expand...
Click to collapse
YOU DON'T NEED TO ENABLE USB DEBUGGING IF YOU'RE GOING TO BOOT FLASHTOOL!!!
Sent from my ST25i using Tapatalk 2
Ali Suhaimi said:
my phone stucked on flash mode and the problem is i cant get it on like usual.. im using xperia u.. and before flashing i forgot to enable usb debuging and now its stuck on flash mode!
HELP
Click to expand...
Click to collapse
Fiest thing first, what phone is it?
Try to explain exactly what have you done, and how do you tell it's in flashmode?
Okay.. im using xperia u.. im trying to downgrade it to GB.. and im using flashtool.. but when i
connect it,it says that 'The last USB device you connected to this computer malfunctioned,and windows does not recognize it'.. and the flashtool says that devide connected in flashmode..
04/045/2013 10:45:44 - INFO - Device connected in flash mode
04/045/2013 10:45:46 - INFO - Device disconnected
04/046/2013 10:46:03 - INFO - Device connected with USB debugging off
04/046/2013 10:46:07 - INFO - Device disconnected
04/048/2013 10:48:26 - INFO - Selected st25i_2.3.7_t-mobile hu_6.0.b.3.184.ftf
04/048/2013 10:48:26 - INFO - Preparing files for flashing
04/048/2013 10:48:40 - INFO - Searching Xperia....
04/048/2013 10:48:40 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:41 - INFO - Searching Xperia....
04/048/2013 10:48:41 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:42 - INFO - Searching Xperia....
04/048/2013 10:48:42 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:43 - INFO - Searching Xperia....
04/048/2013 10:48:43 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:44 - INFO - Searching Xperia....
04/048/2013 10:48:44 - ERROR - USB\VID_0FCE&PID_ADDE\5&9854CDB&0&1
04/048/2013 10:48:45 - INFO - Device connected in flash mode
04/048/2013 10:48:45 - INFO - Searching Xperia....
04/048/2013 10:48:45 - ERROR - USB\VID_0FCE&PID_ADDE\5&9854CDB&0&1
04/048/2013 10:48:46 - INFO - Searching Xperia....
04/048/2013 10:48:46 - ERROR - USB\VID_0FCE&PID_ADDE\5&9854CDB&0&1
04/048/2013 10:48:47 - INFO - Device disconnected
04/048/2013 10:48:47 - INFO - Searching Xperia....
04/048/2013 10:48:47 - ERROR - Please plug you device in flash mode
04/048/2013 10:48:48 - INFO - Searching Xperia....
04/048/2013 10:48:48 - ERROR - Please plug you device in flash mode
and now when im trying to turn on my phone the green light flashes but the screen only show ! sign in a triangle with a phone.. then it turns off..
@Ali Suhaimi
Id the phone turned off before you start flashing?
Did you install the drivers from flashtool located in drivers directory? You need to install 4, the one for Sola and flash and fastboot mode that are at the bottom of the list.
Before you flash just leave flashtool open and connect in flash mode, and see it stays connected for about 45 seconds.
Yes i've done all.. but the problem is i forgot to enable USB Debugging before flashing it.. and now the flashtool need the USB debugging to be enabled and i cant turn on the phone,.
Ali Suhaimi said:
Yes i've done all.. but the problem is i forgot to enable USB Debugging before flashing it.. and now the flashtool need the USB debugging to be enabled and i cant turn on the phone,.
Click to expand...
Click to collapse
Bo USB devugging has absolutely nothing to do with flasg mode as was posted before vy Little Zed.
What is your windows version?
Please post a log of dlashtool fr connecting in flash mode. Do not flush anything just open flashtool and connect in flash mode.
Related
Today i updated my NEO in PC Companion software. Now after update it wont boot.
If i long press the power bottun it just vibrates shortly and nothing happens, sometimes i get a short green flash from the led. but nothing else.
what to do?
Hi bro more info needed.
Like what were you on ,firmware.....
Were you rooted .or open bootloader
Or was it just new / or on 2.3.2 to 2.3.3/4
Could the download of the file in sony ericsson be corrupt
......let is know
Sent from my MT15i using xda premium
http://androidflip.com/how-to-update-sony-ericsson-xperia-neo-to-2-3-4-gingerbread-update/
That's all you need.
sent from Xperia neo
kormatoes said:
Hi bro more info needed.
Like what were you on ,firmware.....
Were you rooted .or open bootloader
Or was it just new / or on 2.3.2 to 2.3.3/4
Could the download of the file in sony ericsson be corrupt
......let is know
Sent from my MT15i using xda premium
Click to expand...
Click to collapse
ok here's the deal... its my wifes phone and she updated last night. So i really dont know what version firmware was on it before, but the update that was applied was the new .283 update.
It was not rooted and not messed with booloader or anything, just stock 2.3.3.
himanshpahwa said:
http://androidflip.com/how-to-update...rbread-update/
That's all you need.
sent from Xperia neo
Click to expand...
Click to collapse
Is this the way to do it? Can i keep the settings/data this way?
Just go ahead and follow the steps
I'm sure it will work for you.
But the data will be lost.
sent from Xperia neo
Good luck with following the steps and let us know if you have any trouble with it, hope you can get the phone unbricked.
Thank you all, for your help!
Actually I just unticked, the "wipe data" box in flash tools and the phone is now updated and fully working with all data intact... :-D
Thank God for xda!
Hello, can you please help me! I bricked my xperia neo, while trying to update se tweaked rom v 8.5. Now i'm facing the "sony ericsson" screen, totaly blocked. I've tried many times to flash it, whith wotan client, flash tool, but it's imposible to enter flash mode again, no green led, only bocked se screen, please help!!!
follow my thread and everything will be fine.
http://forum.xda-developers.com/showthread.php?t=1324707
04/025/2012 13:25:50 - ERROR - Please plug you device in flash mode
04/025/2012 13:25:51 - INFO - Searching Xperia....
04/025/2012 13:25:51 - ERROR - Please plug you device in flash mode
04/025/2012 13:25:52 - INFO - Searching Xperia....
04/025/2012 13:25:52 - ERROR - Please plug you device in flash mode
04/025/2012 13:25:53 - INFO - Searching Xperia....
04/025/2012 13:25:53 - ERROR - Please plug you device in flash mode, etc my phone cannot be seen no more by the pc, but it worked perfect in the past flash mode, fastboot mode "se" screen pops up whithout turnig on the phone and remains, dont know what happened to this phone
Take your battery for at least 5 seconds.
Put it back again.
Press back button and connect the cable with the back button pressed.
Then start fota unbrick.
Try it several times.
Sometimes and thats weird the computer as problems connecting to phone.
I warrant you that the thing works and you are with the right problem.
Your trim area is damaged.
Thanks! I've tried like 50 times, and nothing, the ennoing "sony ericsson" is booting (no sony ericsson logo as usualy, just the writing) I flashed 10 times in the past whith no problem. Now, even when I put it to charge ( wall charge) the phone is turning on showing that stupid "sony ericsson" writting, I cant shut it down from the on\off button. Before killling it, I've instales stock MT15i_4.0.A.2.368_GLOBAL ROM, then I upgraded to MT15i_4.0.2.A.0.42_Global, then rooted with DooMLoRD_v4_ROOT-zergRush-busybox-su, Installed CWM( wiped cache, updated SE tweaked v8.5 Rom) After the restart, the "se" writting started booting. I've pulled out the batery, and begined flashing it with flash tool(no green led).The flashing started and my little brother accidentaly pulled out the Usb cable; that's the whole story! I've tried like 100 times with wotan, flash tool and FlashTool_0.2.9.1_FOTAUnbrick, no result, even if pc companion tells me "phone conected" and gives me further instructions whith the phone being dead, and the flash tool showing me to connect de device... Thank you for all the help, hope there is a solution. sorry for the long post and my bad english...
---------- Post added at 11:45 PM ---------- Previous post was at 11:28 PM ----------
04/040/2012 23:40:02 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/040/2012 23:40:04 - INFO - Device disconnected
04/040/2012 23:40:06 - INFO - Device connected with USB debugging off
04/040/2012 23:40:06 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/040/2012 23:40:07 - INFO - Device disconnected
04/040/2012 23:40:10 - INFO - Device connected with USB debugging off
04/040/2012 23:40:10 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/040/2012 23:40:18 - INFO - Device disconnected
04/040/2012 23:40:35 - INFO - Device connected with USB debugging off
04/040/2012 23:40:35 - INFO - For 2011 devices line, be sure you are not in MTP mode
Flash tooll results when trying to connect (pulling batery-10 secs, back butoon, usb cable)
Look, read carefully.
You can´t have that log, this log shows that your phone is connected (powered on).
Withou green line you re not ready to go.
Just follow as I´ve writted before.
Battery of for 5 secs. take the back button and plug the cable. After that you must run fota unbrick.
then just flash and your phone should be good.
If not PM and I give you another solution.
Thank you again! I tried, my phone was bricked before, but I've managed every time to get into the flash mode, and flashing it succesfully. This time is bad, i pulled the batery out for hours, coonect the batery-nothing happens, push the back button-nothing happens, While holding the back button-conect the usb port to pc-after 3-4 secs, that "sony ericsson" screen apears (no green logo, just the writting) no green led, somehow pc companion tells me i'm "connected" and shows me further steps, but on the phone it's just that "se" writting. No mather how bricked was my phone before, It allways got into the flash mode (1-4tries) I even reinstaled Windows, drivers, hope I want damage the usb port of the phone Have a great day!
Hello everybody,
My Xperia Mini ST15i (with 2.3.4 ROM, & 4.0.2.a.0.42 Build Number) can't turn on properly.
Just stuck at 'Sony Ericsson' (before the logo).
I tried to press power + volume down, but it wont open the CWM.
Then I want to flash with the latest flashtool 0.9.xx, but the log status was:
29/044/2013 21:44:06 - INFO - <- This level is successfully initialized
29/044/2013 21:44:06 - INFO - Flashtool Version 0.9.11.0 built on 2013-06-04 22:50:00
29/044/2013 21:44:35 - INFO - Device disconnected
29/046/2013 21:46:03 - INFO - Device connected with USB debugging off
29/046/2013 21:46:03 - INFO - For 2011 devices line, be sure you are not in MTP mode
So what should I do for this problem?
Even I can't turn on the USB debugging and switch to MSC mode because the device stuck at 'Sony Ericsson'.
Everybody please help me
I can't do this without your kindness and your guide.
Thanks a lot. I hope you all can reply my mesage.
kesuma27 said:
Hello everybody,
My Xperia Mini ST15i (with 2.3.4 ROM, & 4.0.2.a.0.42 Build Number) can't turn on properly.
Just stuck at 'Sony Ericsson' (before the logo).
I tried to press power + volume down, but it wont open the CWM.
Then I want to flash with the latest flashtool 0.9.xx, but the log status was:
29/044/2013 21:44:06 - INFO - <- This level is successfully initialized
29/044/2013 21:44:06 - INFO - Flashtool Version 0.9.11.0 built on 2013-06-04 22:50:00
29/044/2013 21:44:35 - INFO - Device disconnected
29/046/2013 21:46:03 - INFO - Device connected with USB debugging off
29/046/2013 21:46:03 - INFO - For 2011 devices line, be sure you are not in MTP mode
So what should I do for this problem?
Even I can't turn on the USB debugging and switch to MSC mode because the device stuck at 'Sony Ericsson'.
Everybody please help me
I can't do this without your kindness and your guide.
Thanks a lot. I hope you all can reply my mesage.
Click to expand...
Click to collapse
try to flash stock rom
http://forum.xda-developers.com/showthread.php?p=43897224
You need to be in flashmode to flash something
This means take out the battery, wait a few seconds, insert it again, hold volume down and while holding volume down connect the phone to your pc. The green led will indicate you are in flashmode.
Then you click in flashtool on the flash - flashmode - select the .ftf for your device (mini, st15, smultron) and click OK.
When it has finished flashing you should be able to boot up your phone
Or even better and easier would be the repair option in PC Companion or Sony Update Service :good:
Sent from my Nexus 4 running Android 4.3
mihahn said:
You need to be in flashmode to flash something
This means take out the battery, wait a few seconds, insert it again, hold volume down and while holding volume down connect the phone to your pc. The green led will indicate you are in flashmode.
Then you click in flashtool on the flash - flashmode - select the .ftf for your device (mini, st15, smultron) and click OK.
When it has finished flashing you should be able to boot up your phone
Or even better and easier would be the repair option in PC Companion or Sony Update Service :good:
Sent from my Nexus 4 running Android 4.3
Click to expand...
Click to collapse
Okay mihahn , i've tried to flash in flashmode with flashtool
I've downloaded the Stock Firmware 4.0.2.a.0.42 and put that .ftf to folder: /firmwares
But when the device connected to USB PC, the log status was:
Need to switch to MSC Mode
Need to switch to USB debugging ON
Can I do this flashing without switch to ON USB debug & switch to MSC Mode?
I still confuse
And the step to press volume down when connecting to PC doesn't available
Plase help me, thanks a lot
kesuma27 said:
Okay mihahn , i've tried to flash in flashmode with flashtool
I've downloaded the Stock Firmware 4.0.2.a.0.42 and put that .ftf to folder: /firmwares
But when the device connected to USB PC, the log status was:
Need to switch to MSC Mode
Need to switch to USB debugging ON
Can I do this flashing without switch to ON USB debug & switch to MSC Mode?
I still confuse
And the step to press volume down when connecting to PC doesn't available
Plase help me, thanks a lot
Click to expand...
Click to collapse
You don't need to enable anything
In flashtool do what I told you, select the ftf etc and click ok. There'll be a windows that tells you to connect the device in flashmode.
Now you take the battery out of your phone, wait a few secs, insert it again and now just press volume down and connect it via usb to your PC. Don't power it on! Just press volume down while it's turned off and connect the usb
It will automatically start flashing and when it's finished, unplug your device and start it. If it won't start flashing because it doesn't recognize your device, go to the flashtool installation folder - drivers and install all drivers for all modes/devices again. Then try to flash the firmware like I told you :good:
Sent from my Nexus 4 running Android 4.3
mihahn said:
You don't need to enable anything
In flashtool do what I told you, select the ftf etc and click ok. There'll be a windows that tells you to connect the device in flashmode.
Now you take the battery out of your phone, wait a few secs, insert it again and now just press volume down and connect it via usb to your PC. Don't power it on! Just press volume down while it's turned off and connect the usb
It will automatically start flashing and when it's finished, unplug your device and start it. If it won't start flashing because it doesn't recognize your device, go to the flashtool installation folder - drivers and install all drivers for all modes/devices again. Then try to flash the firmware like I told you :good:
Sent from my Nexus 4 running Android 4.3
Click to expand...
Click to collapse
Okay, I try now.
I'll report to you the log later. THX before mihahn
Thanks a lot! mihahn, tips from you was so amazingly MAGIC!
It Works! I just thanked you.
Once again, thank you.
kesuma27 said:
Okay, I try now.
I'll report to you the log later. THX before mihahn
Thanks a lot! mihahn, tips from you was so amazingly MAGIC!
It Works! I just thanked you.
Once again, thank you.
Click to expand...
Click to collapse
No problem, for any further issues just ask again and I'm sure somebody will help you
Sent from my Nexus 4 running Android 4.3
When I try to boot my phone, the sony logo shows up and then nothing happens. I have CWM installed but pressing vol. down doesn't open the recovery. I tried to flash stock firmware using flashtool, but when I connect phone in flashmode/fastboot mode, the phone connects properly for about 10 seconds, then boots and again stuck at sony logo.
I know I'm supposed to connect only when flashtool says to connect the phone, and doing just that but still not working. Please help!
hoodakaushal said:
When I try to boot my phone, the sony logo shows up and then nothing happens. I have CWM installed but pressing vol. down doesn't open the recovery. I tried to flash stock firmware using flashtool, but when I connect phone in flashmode/fastboot mode, the phone connects properly for about 10 seconds, then boots and again stuck at sony logo.
I know I'm supposed to connect only when flashtool says to connect the phone, and doing just that but still not working. Please help!
Click to expand...
Click to collapse
It'sa good thing you forgot to mention what windows version you are on or ig you have used flashtool before on that PC so we can waste some time while you waiting for help.
Is your phone completely turned off when you are trying to connect in flash mode?
ChikeD said:
It'sa good thing you forgot to mention what windows version you are on or ig you have used flashtool before on that PC so we can waste some time while you waiting for help.
Is your phone completely turned off when you are trying to connect in flash mode?
Click to expand...
Click to collapse
Sorry. I'm on Windows 8, and yes, I've used flashtool before. I also tried to flash from a different pc with windows 7, and the same problem is there.
Yes, phone is completely turned off when trying to connect in flash mode.
Here's the log for flashtool:
29/050/2013 11:50:50 - INFO - <- This level is successfully initialized
29/050/2013 11:50:50 - INFO - Flashtool Version 0.9.13.0 built on 2013-06-04 22:50:00
29/050/2013 11:50:55 - INFO - Device disconnected
29/051/2013 11:51:18 - INFO - Selected LT22i / 6.2.A.1.400 / India_acervenky
29/051/2013 11:51:18 - INFO - Preparing files for flashing
29/051/2013 11:51:18 - INFO - Please connect your device into flashmode.
29/059/2013 11:59:20 - INFO - Device connected in flash mode
29/059/2013 11:59:20 - INFO - Opening device for R/W
29/059/2013 11:59:24 - INFO - Start Flashing
29/059/2013 11:59:24 - INFO - Processing loader.sin
29/059/2013 11:59:24 - INFO - Checking header
29/059/2013 11:59:24 - INFO - Ending flash session
29/059/2013 11:59:24 - ERROR -
29/059/2013 11:59:24 - ERROR - Error flashing. Aborted
29/059/2013 11:59:25 - INFO - Device connected in flash mode
29/059/2013 11:59:26 - INFO - Device disconnected
29/000/2013 12:00:39 - INFO - Device connected in fastboot mode
29/000/2013 12:00:47 - INFO - Device disconnected
@hoodakaushal
I assumed you used it before, I asked if you have used it on that PC.
Try latest version of flashtool: http://www.flashtool.net/
See the FAQ for instructions to install on windows 8.
Also, USB 3 ports won't work, so use USB 2 ports or if you don't have those look at the BIOS for option to switch from xHCI to EHCI.
ChikeD said:
@hoodakaushal
Also, USB 3 ports won't work, so use USB 2 ports or if you don't have those look at the BIOS for option to switch from xHCI to EHCI.
Click to expand...
Click to collapse
Yeah, alreaady figured out that was the problem, tried USB 2 and worked fine. Thanks though! :good:
hoodakaushal said:
Yeah, alreaady figured out that was the problem, tried USB 2 and worked fine. Thanks though! :good:
Click to expand...
Click to collapse
Same problem. Even after using usb 2.0, it stays in flash mode for a few seconds then the sony logo starts in a loop again. Cant access cwm or flash mode. What should I do?
I was trying to flash a new kernel in my phone, how ever i counld not boot in recovery mode, after some googling i found out that to enter the recovery mode i had to install an ics version (i curently have jb 4.1.2) i followed the instructions on a in youtube video.
But when i was finished and tryied to boot up my phone nothing worked it only vibrates once and dosent even light the screen it only blinks red light and when i try flashboot mode it blinks a purple light.
When i try to connect it to my pc via usb it doesn't even recognize its a phone.
When i tryied to connect it to my pc to try and use Update service it blinks green light.
Sometimes when i connect my phone to my pc via usb i can see it in my device manager as an USB MTP device.
Also when i try to charge it blinks a green or a red light for a shortwhile, then the light stop blinking, and then does nothing.
Can someone help me please?
huh
karafliaris said:
I was trying to flash a new kernel in my phone, how ever i counld not boot in recovery mode, after some googling i found out that to enter the recovery mode i had to install an ics version (i curently have jb 4.1.2) i followed the instructions on a in youtube video.
But when i was finished and tryied to boot up my phone nothing worked it only vibrates once and dosent even light the screen it only blinks red light and when i try flashboot mode it blinks a purple light.
When i try to connect it to my pc via usb it doesn't even recognize its a phone.
When i tryied to connect it to my pc to try and use Update service it blinks green light.
Sometimes when i connect my phone to my pc via usb i can see it in my device manager as an USB MTP device.
Also when i try to charge it blinks a green or a red light for a shortwhile, then the light stop blinking, and then does nothing.
Can someone help me please?
Click to expand...
Click to collapse
i've been in the same situation with my xperia p, don't worry it can be fixed. download a tft file and flash it with flashtool.
there are many tutorials on xda how to do that. its all good man, don't worry.
rownz1337 said:
i've been in the same situation with my xperia p, don't worry it can be fixed. download a tft file and flash it with flashtool.
there are many tutorials on xda how to do that. its all good man, don't worry.
Click to expand...
Click to collapse
How to flash with flashtool if i can't connect my phone to my pc?
rownz1337 said:
i've been in the same situation with my xperia p, don't worry it can be fixed. download a tft file and flash it with flashtool.
there are many tutorials on xda how to do that. its all good man, don't worry.
Click to expand...
Click to collapse
Something is wrong, here is what it says in flashtool:
17/006/2014 00:06:19 - INFO - Device connected in flash mode
17/006/2014 00:06:20 - INFO - Start Flashing
17/006/2014 00:06:20 - INFO - Processing loader.sin
17/006/2014 00:06:20 - INFO - Checking header
17/006/2014 00:06:20 - ERROR - Processing of loader.sin finished with errors.
17/006/2014 00:06:20 - INFO - Ending flash session
17/006/2014 00:06:20 - ERROR -
17/006/2014 00:06:20 - ERROR - Error flashing. Aborted
17/006/2014 00:06:20 - INFO - Device connected in flash mode
17/006/2014 00:06:26 - INFO - Device disconnected
https://www.youtube.com/watch?v=FzOPuvnJGq4
i managed to flash my phone with the official 4.1.2 JB and it opened but the touchscreen didn't work.
and then i flashed it with an ICS rom but I EXCLUDED THE KENEL and opened my phone and, for a second appeared the sony logo, then nothing worked.
Just installed the 4.0.4 from the description of the youtube video and it works. thx man :laugh:
i have a problem with my superuser "can't find SU"
karafliaris said:
i have a problem with my superuser "can't find SU"
Click to expand...
Click to collapse
If you flash phone with stock rom you need root phone again
http://forum.xda-developers.com/showthread.php?t=1886460
shoT. said:
If you flash phone with stock rom you need root phone again
http://forum.xda-developers.com/showthread.php?t=1886460
Click to expand...
Click to collapse
I locked my bootloader > updated via pc companion to 4.1.2 > ulocked bootloader > rooted with the help of this link http://untitled-community.blogspot.gr/2014/02/how-to-root-and-install-cwm-recovery.html
thnx man
Hey,
tried to flash Nougat ROM for my Xperia Z2 via TWRP. Flashed all according to the manual. After each step I made an clear cache and after rebooting my device I only have an black screen. When device is plugged in and trying to turn on by pressing the power button red LED flashes three times and nothing happens. What can I do now?
Flundermann said:
Hey,
tried to flash Nougat ROM for my Xperia Z2 via TWRP. Flashed all according to the manual. After each step I made an clear cache and after rebooting my device I only have an black screen. When device is plugged in and trying to turn on by pressing the power button red LED flashes three times and nothing happens. What can I do now?
Click to expand...
Click to collapse
Try to flash stock rom by flashtools
same problem and when i try to use flashtool device getting disconnect & reconnect in every 7 secs.
21/019/2016 03:19:40 - INFO - Device disconnected
21/019/2016 03:19:41 - INFO - Device connected with USB debugging off
21/019/2016 03:19:41 - INFO - For 2011 devices line, be sure you are not in MTP mode
21/019/2016 03:19:47 - INFO - Device disconnected
21/019/2016 03:19:48 - INFO - Device connected with USB debugging off
21/019/2016 03:19:48 - INFO - For 2011 devices line, be sure you are not in MTP mode
21/019/2016 03:19:55 - INFO - Device disconnected
21/019/2016 03:19:56 - INFO - Device connected with USB debugging off
21/019/2016 03:19:56 - INFO - For 2011 devices line, be sure you are not in MTP mode
21/020/2016 03:20:03 - INFO - Device disconnected
21/020/2016 03:20:03 - INFO - Device connected with USB debugging off
21/020/2016 03:20:03 - INFO - For 2011 devices line, be sure you are not in MTP mode
21/020/2016 03:20:11 - INFO - Device disconnected
21/020/2016 03:20:11 - INFO - Device connected with USB debugging off
21/020/2016 03:20:11 - INFO - For 2011 devices line, be sure you are not in MTP mode
raminta said:
Try to flash stock rom by flashtools
Click to expand...
Click to collapse
You have link pls?
Flundermann said:
You have link pls?
Click to expand...
Click to collapse
Link for what???
You can download flashtools on flashtools.net
And find an" .Ftf frimware for Xperia z2" on XDA or search it on Google
And there is many tutorials for flashing using flashtools like this : http://forum.xda-developers.com/showthread.php?t=2054486&page=11
Flundermann said:
Hey,
tried to flash Nougat ROM for my Xperia Z2 via TWRP. Flashed all according to the manual. After each step I made an clear cache and after rebooting my device I only have an black screen. When device is plugged in and trying to turn on by pressing the power button red LED flashes three times and nothing happens. What can I do now?
Click to expand...
Click to collapse
Wich version of nougat do you download? I flashed same as you and it works. Wich version did you download? I downloaded aosp_d6503-20161109-7.1NDE63X-Rcstar6696-N.zip
Try this
Change your USB port to annother and even change cable.
Then download twrp 3.0.0.0 and rename it to recovery.img. from Nougat 7.1 thread http://forum.xda-developers.com/xperia-z2/general/rom-android-n-rom-xperia-z2-t3444169 and download aosp_d6503-20161109-7.1NDE63X-Rcstar6696-N.zip thats what i downloaded but cant run Pixel addon im getting FC on that so i just flashed ROM, GAPPS and SUPERSU.
Now Hold vol+ and connect usb cable to phone and wait until you get blue light.
Then write fastboot flash boot boot.img
Then write fastboot flash recovery recovery.img
now disconnect cable and power on phone. As soon you see SONY logo press vol+ several times and dont stop until you enter TWRP. Now wipe everything except SD card. Then flash and skip clear cache ****. You can clear cache after you done everything then reboot
---------- Post added at 11:16 PM ---------- Previous post was at 11:13 PM ----------
Annother question. Can you turn off the phone? You know about that red button beside SIM card? hold that until phone vibrates and turns off and then hold vol+ and connect cable