Related
My phone was working, I had MiniCM7Pro V21 Installed and I tried to install the CWM Recovery Version 5, because in my installed version the Battery Stats Wipe wasn't working and my battery was draining very quickly.
After the CWM Recovery Version 5 Installation my phone got bricked because it's getting stuck in Sony Ericsson Text.
I am trying to Reflash but only Flash button is active and it doesn't show any firmware though I have copied both zip and unzipped files in firmware folder in FlashTool_0.2.9.1
I tried to use SuperOneClick to root but it gets stuck in Waiting for device. Kindly help.
It gives the following error :-
OK
Pushing rageagainstthecage...
error: device not found
FAILED
I have installed it.
ggsetup-2.2.0.10
Press home+power button until you see black screen, then immediately press and hold back button plugging your phone into computer. When you see black screen and green flashlight-> your phone is correctly booted into restore mode. From this mod, you can restore your phone, using SE restore tools: SEUS and Sony Ericsson Pc Companion, or flash stock kernel using flashtool.
P.S. If you wont see black screen and green flashlight for the first time, try it again, again until you putt your phone safely into restore mode.
Thank you for the reply, the black screen do u mean the black screen with Sony Ericsson Text ? When I Press Home+Power Button I can see the Sony Ericsson Text Black Screen and then I press and hold the back buton Pluging my phone into computer I keep on seeing the Sony Ericsson Text Black Screen with no green flashlight.
I am still trying.
Black screen without any logos. Just black screen. Don't forget to hold back button.
Doing that, but it still gets into Sony Ericsson Text Screen, I press home and the power button, black screen for a while and I press back button and try to connect the phone the Sony Ericsson logo appears.
But When the cable connected and back button pressed the I can see the charging image and green light flash.
and in Flasher it shows the following :-
07/007/2012 23:07:36 - INFO - Device connected with USB debugging off
07/007/2012 23:07:36 - INFO - For 2011 devices line, be sure you are not in MTP mode
camelgrg said:
Doing that, but it still gets into Sony Ericsson Text Screen, I press home and the power button, black screen for a while and I press back button and try to connect the phone the Sony Ericsson logo appears.
But When the cable connected and back button pressed the I can see the charging image and green light flash.
and in Flasher it shows the following :-
07/007/2012 23:07:36 - INFO - Device connected with USB debugging off
07/007/2012 23:07:36 - INFO - For 2011 devices line, be sure you are not in MTP mode
Click to expand...
Click to collapse
reflash to stock kernel and ROM
- install PC companion.
- connect phone in repair mode
- install drivers.
- after driver installed, reflash stock kernel using flashtool
- after stock kernel installed, reflash stock ROM using PC companion
- after stock kernel and ROM flashed,your phone should be like just when you bought it.
- bootloader should be locked now
- Root again
- unlock bootloader again
- Flash nAa again
- Flash cm7 again
- DONE!
Thank you for your reply, I have PC Companion Installed, I have a Generic Firmware downloaded, I have no idea what a stock kernel is ?
I am not able to get into this repair mode, I think this mode is when the flash light flashes ?
from the Bootloader part, I think I can do it because I did it before following a tutorial. If you can lease help me with the prior stage to bootloader lock would be highly grateful.
Thank u
Ones again: to enter restore mode you have to power off your phone, using home+power buttons or powering off like I have on picture. Then press and hold back button, while plugging it into computer.
camelgrg said:
Thank you for your reply, I have PC Companion Installed, I have a Generic Firmware downloaded, I have no idea what a stock kernel is ?
I am not able to get into this repair mode, I think this mode is when the flash light flashes ?
from the Bootloader part, I think I can do it because I did it before following a tutorial. If you can lease help me with the prior stage to bootloader lock would be highly grateful.
Thank u
Click to expand...
Click to collapse
- To relock bootloader you need to flash stock kernel which is 2.1.0.a.06 kernel.
- You need to flash stock kernel because if you have nAa kernel or any custom kernel installed, you wont be able to repair your phone using pc companion.
- After flashing stock kernel:
1. open pc companion
2. click support zone. (click start below it)
3. after clicking start, there should be a new window which also has a "start button"
4. on the 2nd start button, there should be a button under it which says "repair"
5. after clicking repair, just follow the steps for you to connect your phone in repair mode.
6. complete the repair installation.
7. DONE!
8. Bootloader should be locked now.
Thank you I was able to restore through PC Companion by getting into repair mode, however I didn't use flashtool to flash prior to usin PC Companion.
Thank you both for your kind support, Highly appreciated.
camelgrg said:
Thank you I was able to restore through PC Companion by getting into repair mode, however I didn't use flashtool to flash prior to usin PC Companion.
Thank you both for your kind support, Highly appreciated.
Click to expand...
Click to collapse
You are welcome my friend
And how should I proceed if I have a really hard brick (u20a)?
I tried to flash nAn on it, followed some instructions to unlock the bootloader, but something went wrong, the results were not the ones that should had been, and I made the mistake of turning it off. Now whenever I try to power it on, it doesn't do squat.
The only thing that makes me think it's still alive is that (after several months) I plugged it in and it began blinking on red (perhaps really low battery).
I've tried to pull the battery, put it back in, press back (keeping it pressed), and then plugging the cable to the computer and nothing.
Any ideas? Or should I flush it down the toilet? :crying:
x10 mini unbricking
Mrakoris/ said:
Press home+power button until you see black screen, then immediately press and hold back button plugging your phone into computer. When you see black screen and green flashlight-> your phone is correctly booted into restore mode. From this mod, you can restore your phone, using SE restore tools: SEUS and Sony Ericsson Pc Companion, or flash stock kernel using flashtool.
P.S. If you wont see black screen and green flashlight for the first time, try it again, again until you putt your phone safely into restore mode.
Click to expand...
Click to collapse
i tried the thing you suggested, but the green light only lasts a while even if i continue to hold the back button. also, i am not able to repair my phone through se pc companion, as it keeps cancelling the repair update the moment the green light stops appearing. any help? thanks!
Hi guys,
I know that here is a lot of infos regarding this, but I cannot get Fastboot mode on my XU. To get Flash mode is no problem (VOL_DOWN + cable), but I cannot get Fastboot mode (VOL_UP + cable). Am I doing something wrong?
a, turning phone OFF
b, plugging USB cable while pressing VOL_UP button
It's Xperia U. I tried to do it appr. 20 times but without success, phone is allways getting only chargin icon with red LED on right upper corner....
Thx
Does your phone boots?
Yes of course, everything is working OK except ability to enter Fastboot mode... That's why I'm asking if I'm doing something wrong or where's the problem... I want to unlock bootloader through Flashtool (I received unlock code from SONY by mail). But to do that, I have to connect phone in Fastboot mode
Brfore turns into charging mode is it light the blue colour?
Sent from my xperia sola using xda premium
No no. It's going only red (small LED in upper right corner) and I receive battery icon on screen. Is possible that I cannot enter Fastboot mode, because I have "Bootloader Unlock Allowed=NO"? But now I'm thinkning that my question is useless, because if my option =NO, then I'll be not able to unlock bootloader, even if I received official unlock code....
rado77 said:
No no. It's going only red (small LED in upper right corner) and I receive battery icon on screen. Is possible that I cannot enter Fastboot mode, because I have "Bootloader Unlock Allowed=NO"? But now I'm thinkning that my question is useless, because if my option =NO, then I'll be not able to unlock bootloader, even if I received official unlock code....
Click to expand...
Click to collapse
U cant go into fastboot mode when u bootloader is locked
Dr.Sanket,
thank you very much for info THANK button hitted
rado77 said:
Hi guys,
I know that here is a lot of infos regarding this, but I cannot get Fastboot mode on my XU. To get Flash mode is no problem (VOL_DOWN + cable), but I cannot get Fastboot mode (VOL_UP + cable). Am I doing something wrong?
a, turning phone OFF
b, plugging USB cable while pressing VOL_UP button
It's Xperia U. I tried to do it appr. 20 times but without success, phone is allways getting only chargin icon with red LED on right upper corner....
Thx
Click to expand...
Click to collapse
This phone will exit fastboot mode if you dont have the drivers installed correctly. You need to be fast to install them before the phone exits the fastboot mode.
Also you need to have your bootloader unlocked or it will not work.
I've tried to install Cyanogenmod 9 on my Xperia Sola, I've unlocked bootloader official way, flashed kernel from this forum specialy made for sola (http://forum.xda-developers.com/showthread.php?p=28957468&postcount=412 This One), then boot.img of cyanogenmod 9 (FXP203) and...
When I want to do anything with phone, it just flashes my red led. I mean, that led is still on, when I press Power it just turn off. And when I try to connect my phone in fastboot mode, It don't react at all. Can I already throw it away through window?
I put it under a charger to see if it's just off energy, but i've noticed, that after a while, red led just turns off and that's all.
My god, help me or I'll be back on Nokia 3310
You've used the S kernel, not the Sola.
Download the FXP for Sola (Pepper) here;
http://forum.xda-developers.com/showthread.php?t=1876929
Flash boot.img via fastboot. To get in, hold vol up + power. Wait for 3 vibrations.
Hold vol up. Then jam the USB cable in. You should be in fastboot.
Alternatively, flash the stock sola ftf via flashboot.
Problem is, my phone does not react, it does not vibrate, just that red led is on or off. Nothing else. I've tried all of those combinations. I can't get to fastboot mode or anything else.
MelaPL said:
Problem is, my phone does not react, it does not vibrate, just that red led is on or off. Nothing else. I've tried all of those combinations. I can't get to fastboot mode or anything else.
Click to expand...
Click to collapse
Happened to me (I use Xperia GO). What I did is (as mentioned above) - Hold the power button and Volume Up button for sometime (it vibrates once after a few seconds, do not leave the buttons - continue to do so and after a few more seconds until 3 vibrations) and then the phone switches off. Now, hold the Volume Up button and plug in the USB cable - you'd be able to get in the fastboot mode. Flash a stock kernal and that should help.
If your phone is completely down (no charge at all), then above won't help. Plugin the charger and and wait for a few mins (before the red light goes off - you should now have a good knowledge on when the light goes off!) and try then try the above step. Once the 3 vibration comes, remove the charger and go ahead with the flash mode.
Hope this helps!
Thanks,
B.
Edit: By the way, I had my SIM Card and Memory card inserted in the phone when the phone was completely down without any charge. I don't know how, but it makes a difference with you try so (atleast in my case) with them.
If it does not vibrate, then it's a hard brick =\ You need the phone to be at least partially responsive to get into fastboot/flashboot.
Keep holding down. It should vibrate after 25 seconds or so.
Otherwise, you have to bring it to Sony and tell them their phone died on you.
Right now It dosen't even blink with Led. It's totaly down. I cant lock fbootloader, so I'm doomned. Hope that won't cost much...
Install Sony Update Service (SUS) and try to recover your phone from there.
Last shot here, but here's to hoping that the PC at least detects your phone.
Otherwise.... Yeah =\
If you unlocked your bootloader Pc companion will be useless for you cause it will not detect your phone,.,,
i think other way is to flash the stock ftf for you device using flashtool.... that wuld be the best shot for you...
please respond if this fix your problem
No, SUS will detect, but will refuse to flash. It will say "Phone has been modified".
Need to see whether it's a hard brick. If even SUS does not recognise, then bring it to Sony =\
None of the above works. It's just dead and sometimes flashes red light. PC Companion says that there's no phone connected. Hope I will be able to gain a varranty or I'll be on Nokia 3310. But I'm not verry cheerful about that...
Flashtool does not react when I plug in my phone in fastboot or flash.
Hey bro,
Its highly unlikely for hardbrick to happen to Sony phones by flashing a differnt Kernel when Flashtool is there Pretty sure that it ought to work, follow the steps below (Note that the order of usb cable connection is the most important thing as doing it wrong will not allow Flashtool to connect to the phone when its bricked ! )
First, try plugging it in to charger for a while to ensure that there's some charge. Follow up with the Vol and power Button to make sure its turned off. Then after that follow this procedure *exactly*
1) Prepare Flashtool and select the FTF. (Flashmode )
2) When flashtool asks yo to connect the phone, connect the USB cable to PC
3) Then, holding down ONLY the Vol Down button (No Power button, Note that ) connect the phone to the USB cable and in a few seconds, Flashtool will start flashing
I know you tried many variations but missing out on one or the other detail during your previous tries might have caused the lack of success Just try it and let us know what happens
Best of luck and hope you dont have to go to Nokia World !
Cheers
Nope, it's still not working. It just dosent detect phone. I'm pluging in, holding only volume key and I'm waiting 5 minutes - nothing happend.
Nokia 5530 for now, but come one...
Hi,
I am currently having the same problem (I have bricked my sola by flashing with fxp boot.img). After digging the internet I found out that you can start fastboot by:
1. holding all 3 buttons (power on, volume +, volume -)
2. the phone will vibrate
3. the phone will vibrate 3 times
4. release the buttons
5. hold the volume + button and plug in the cable
6. you should be in fastboot now (blue light on)
If fastboot does not work then do 1-4 3x. Good luck! Hopefully we will unbrick our phones
Br,
Wermesz
wermesz said:
Hi,
I am currently having the same problem (I have bricked my sola by flashing with fxp boot.img). After digging the internet I found out that you can start fastboot by:
1. holding all 3 buttons (power on, volume +, volume -)
2. the phone will vibrate
3. the phone will vibrate 3 times
4. release the buttons
5. hold the volume + button and plug in the cable
6. you should be in fastboot now (blue light on)
If fastboot does not work then do 1-4 3x. Good luck! Hopefully we will unbrick our phones
Br,
Wermesz
Click to expand...
Click to collapse
Lol things u get on the internet!!!
First there is no such key combination to start fastboot k so just dun break ur buttons in an attempt to start it ...
Steps 1,2&3 are steps to get ur device force restart and force shutdown and let me tell you one thing
step 1 is wrong it power button and volume + button. That's it first the phone will vibrate once for force restart and if u keep pressing it will bypass over to force shutdown which is indicated by 3 vibrations..
Sent from my Xperia Sola using xda premium
could work
I have a Xperia U and triying to port JB to it I briked two or three times.
I hold power botom and it vibrate and doesnt happen anything ok.?¿
The possible solution could be this(for my works)
Charge the phone like 1 hour for my doesnt charge with the animation but its for security.
With the nest steps you are going to lose all CWM and tweaks and apks but personal data still there.
You have two options:
Flash a new rom with flashtool, but when you pluged with volum - you hold it for allmost all process becose for my i conect to PC and its goes quikly so i cant do annything.
If the phone is not recognised by Flashtool:
You have to repair it with PC Companion or Bridge for Mac, and also the same hold volum - almost all process.
For my it works, tell my if for you works:cyclops::cyclops::cyclops:
Hi,
it worked !
after doing the steps I have posted earlier I managed to flash my xperia sola with the right boot.img (the one from fxp pepper) and install fxp via CWM. Should work for you too.
One tip: you have to remove the assert from fxp installation script.
Br,
Wermesz
@op, your battery is dead and isn't accepting any external charge. Try replacing your battery with a charged one. That is if sola supports user replaceable batteries.
Sent from my ST25i using xda app-developers app
Hey,
I have a problem. My tablet is SGP312 has Cyanogenmod 11 (FXP247 - Android 4.4). It was bricked when I type in Terminal:
Code:
su
reboot recovery
Was turned off and will not turn on at all.
Power button = NOTHING
Power button + Vol(+) 3/10/25 secs = NOTHING
Power button + Vol(-) 3/10/25 secs = NOTHING
Power button + Voll(+) + USB = NOTHING
No LED light, It's literally a paperweight. I can't even put it into Flashmode.
Please help me!
Anyone can help me?
WeRunTheNite said:
Anyone can help me?
Click to expand...
Click to collapse
Are you sure u can't put it in to flash mode, because that's the first thing I would do
Try putting it into fast boot mode
Hold volume up button and keep holding it and connect it to the pc
If you see blue light on your tablet, it means it has successfully entered fast boot mode
Make sure all the drivers are installed
Or
Follow the following procedures
Install Sony Ericsson flash tool and install all the drivers
Hold volume down button and keep holding it and connect it to pc
Once you hear the connecting sound our Any notification on your pc saying that it is connected, go ahead and flash the ftf file
hassanman1997 said:
Are you sure u can't put it in to flash mode, because that's the first thing I would do
Try putting it into fast boot mode
Hold volume up button and keep holding it and connect it to the pc
If you see blue light on your tablet, it means it has successfully entered fast boot mode
Make sure all the drivers are installed
Or
Follow the following procedures
Install Sony Ericsson flash tool and install all the drivers
Hold volume down button and keep holding it and connect it to pc
Once you hear the connecting sound our Any notification on your pc saying that it is connected, go ahead and flash the ftf file
Click to expand...
Click to collapse
When I hold volume up or volume down and connect it to PC, light turn on in red color. Flashtool says "device connected with usb debugging off" but tablet is off!
Driver
WeRunTheNite said:
When I hold volume up or volume down and connect it to PC, light turn on in red color. Flashtool says "device connected with usb debugging off" but tablet is off!
Click to expand...
Click to collapse
in my opinion, the drivers are not correctly installed
http://developer.sonymobile.com/downloads/drivers/xperia-tablet-z-sgp311-sgp312-driver/
go to the website and download and load the drivers on your pc
its just weird that it says device connected with Usb debugging off when it is actually powered off
try charging your device, maybe the battery needs to be charged leave it there for atleast 30 mins then try the steps
let us know if you fixed it or not
hassanman1997 said:
in my opinion, the drivers are not correctly installed
http://developer.sonymobile.com/downloads/drivers/xperia-tablet-z-sgp311-sgp312-driver/
go to the website and download and load the drivers on your pc
its just weird that it says device connected with Usb debugging off when it is actually powered off
try charging your device, maybe the battery needs to be charged leave it there for atleast 30 mins then try the steps
let us know if you fixed it or not
Click to expand...
Click to collapse
I have a similar problem, I've flashed plenty of devices before, never briked a thing.
By unloking the bootloader the data partition of my brand new tablet Z went corrupted. I've tried to flash several firmware but none was succesfull (couldn't format data...), and finally it get totally bricked! no light, nothing... I was not even able to put it in flash mode (no light ever!).
I've tried after a while, I've read with some other Xperia devices, it would be possible to recover it after some time, by letting the battery die, then use some rubber trick to keep vol- pressed... you can find it in XDA forums what I'm talking about. However after a month my tablet was still dead. no light, no nothing!
I've sent it to warranty and the just said that "an alternative firmware was flashed" (voiding the warranty) "and has rendered the logic board unusable".... and they have to order a new unit!!
I feel so surprise that even the cheapest chinese tablet have an harware mode that allow to reflash and resuscitate it back to factory... even if the firmware is completely screwed, and a 600$ tablet for a simple bootloader unlock got totaly bricked.
I wonder if there is an "hardware" way to recover the tablet (I saw it's pretty easy to tear down the Xperia tablet Z), by directly accessing the NAND... or by accessing some PIN (well I know sony would have not leaked such information)
I know that this thread is more of same, but I didn't found any answer that helps me.
The story is:
My Xperia 2363 M4 Aqua Dual recived a call and I lost it. Then when I took it and turn on the screen to see the caller, my device just restarted and went to the purple waves screen, but stuck there the system didn't start. Since this, the only thing that phone do is that, it never starts the android system.
I've tried everything that I read
So the things I've tried is:
Restart the phone by holding the power + vol up buttons
Turn off the phone by holding the power + vol up buttons until 3 vibes
Turn on the phone holdin the vol up + vol down buttons
Reinstall software by xperia companion but the software didn't start the process
reinstall software by flashtool but the device isn't found by the flashtool
connect the phone on pc holding vol up button
connect the phone on pc holding vol down button
connect the phone on pc holding vol up + vol down buttons
connect the phone holding all the buttons
the fastboot and bootloader modes don't enter and the pc says that usb device can't recognized by the windows.
I have no ideas of what i do
Can you help me?
Does it flash a blue screen briefly before restarting / crashing?
DarkerJava said:
Does it flash a blue screen briefly before restarting / crashing?
Click to expand...
Click to collapse
Thanks for reply. No, didn't flash a blue screen, it just restarted like when we hold the power +vol up buttons
And it not keep restartin, the phone turns on and stays on the waves screen. don't start the system so as don't restart.
If you device is not being recognized by you PC, Try fastbooting the device using a linux (Mint, what i used for similiar issue), it will hopefully recognize your device and you would be able to flash it.
sanjyot said:
If you device is not being recognized by you PC, Try fastbooting the device using a linux (Mint, what i used for similiar issue), it will hopefully recognize your device and you would be able to flash it.
Click to expand...
Click to collapse
Thank You, I'll try this.
sanjyot said:
If you device is not being recognized by you PC, Try fastbooting the device using a linux (Mint, what i used for similiar issue), it will hopefully recognize your device and you would be able to flash it.
Click to expand...
Click to collapse
I tried this one, but, is the phone that not enter on fastboot mode. I tried with my another devices and it worked well, but the M4 aqua, just refuse to enter in fastboot mode and only recharge the batt. to be more specifc, the green or blue lights don't lights
korkinova said:
I tried this one, but, is the phone that not enter on fastboot mode. I tried with my another devices and it worked well, but the M4 aqua, just refuse to enter in fastboot mode and only recharge the batt. to be more specifc, the green or blue lights don't lights
Click to expand...
Click to collapse
could you fix that problem bro?
advancel said:
could you fix that problem bro?
Click to expand...
Click to collapse
Unfortunately no. I couldn't fix this yet, it is because I' can't go fastboot mode on my device
have you any other suggestion?
no i have that problem by the way if you can fix the prob. then contact me pls
The other phone you tried was a Xperia?
And are you on Win8 or Win10 because if you are, you have to install the drivers in unsafe mode(Don't remember how it's really called).
Furthermore if you don't have anything important in the phone try flashing a new version of Android or the same but do a clean install I.E Wipe everything and leave like new by installing with Flashtool(unsafe mode too, because it needs drivers if you are on Win8>10 when installing)