Related
hey hii guyzzz..... i bought my samsung galaxy ace plus 6 days ago... i rooted it and also installed cwm(clockwork mod) from "http://forum.xda-developers.com/showthread.php?t=1618324"..
today i opened system update then it showed that an update of around 8 mb(maybe more i don't remember)so i updated it and i chose to update now for downloaded update.. my phone restarted and started in cwm-based recovery v5.0.2.8.. and since then whatever i do it starts in it again... i tried to remove battery and start it dint worked then removed my micro sd card nothing worked also tried to root again in download mode nothing worked...i am new to android and was too exited so did all rooting and other stuff.. now i am afraid what to do... i think i have bricked my phone plz help as soon as possible....
SOS
Quick question first - Where are you and what network are you on? Because the one below is for INS India so you may need a different firmware
OK try this.
Download this firmware - Samsung Galaxy Ace Plus GT-S7500 (get both parts)
And the flasher - Odin3 v1.83 GT-S7500
Extract everything to the same folder then do this -
1. Open Odin
2. Make sure phone is totally powered off (Remove battery for 30 seconds then reinsert)
3. Boot the phone into Download Mode. You can do this by pressing and holding down the Volume Down and Home buttons while pressing the Power button until you are welcomed by a green robot indicating you are in Download Mode.
4. Once the phone is in Download mode, connect your phone to your PC while keeping the Odin3 application running.
5. Within a few moments, the ID:COM section in the Odin3 application will turn yellow. This indicates that the necessary drivers for your device have been successfully installed on your computer.
6. In Odin3, click the PDA button. Browse for S7500DDLB1_S7500ODDLB1_S7500DDLB1_HOME.tar.md5 and select it.
7. In the Option section in Odin3, make sure only Auto Reboot and F. Reset Time are checked.
8. Hit the “Start” button in Odin3 to begin flashing the Gingerbread firmware to your phone. It may take 5-10 minutes for the installation process to finish. Your phone should automatically reboot itself.
9. As soon as you see the Samsung splash screen, disconnect your phone from your PC.
10. Switch off your phone completely.
11. Reboot the phone into Recovery Mode. You can do this by holding down the Volume Up and Home buttons, then pressing down the Power button.
12. Once inside recovery, perform a wipe:
Select “wipe data/factory reset”, then select “Yes” on the screen that follows to confirm data wipe.
Select “wipe cache partition”, then select “Yes” on the screen that follows to confirm wiping your phone’s cache partition.
13. Head back to the main menu, then select “Reboot system now” to reboot your device.
(If you have problems with the drivers get these and install - Samsung USB Drivers)
Original instructions from here
Hope this helps unbrick your phone. You may need to re-root after this though
I figured that earlier but thanks... I didn't checked xda-forums...... :thumbup:
Sent from Samsung galaxy ace plus using tapatallk....loxy
reboot system now error
same problem here help me out tooo
plz plz plz
lokeshsaini94 said:
hey hii guyzzz..... i bought my samsung galaxy ace plus 6 days ago... i rooted it and also installed cwm(clockwork mod) from "http://forum.xda-developers.com/showthread.php?t=1618324"..
today i opened system update then it showed that an update of around 8 mb(maybe more i don't remember)so i updated it and i chose to update now for downloaded update.. my phone restarted and started in cwm-based recovery v5.0.2.8.. and since then whatever i do it starts in it again... i tried to remove battery and start it dint worked then removed my micro sd card nothing worked also tried to root again in download mode nothing worked...i am new to android and was too exited so did all rooting and other stuff.. now i am afraid what to do... i think i have bricked my phone plz help as soon as possible....
Click to expand...
Click to collapse
I have a standard unlocked UK SGS2.
It has been running ICS since its official Samsung update, and for the past week or so has been displaying a "firmware update available" message.
Today I tried to run the update via Kies. The update hung with the SGS2 displaying the "downloading - do not disconnect target" screen. Eventually, Kies displayed a message that the download had failed, and the phone should be disconnected and rebooted.
Rebooting the phone has given the "handset-exclamation mark - PC" screen.
I have so far tried:
a) following Kies instructions to the letter;
b) switching USB ports on the PC (running Win 7 pro 64);
c) trying the "hold volume up&down + on/off buttons; at second flash release power button", etc;
Nothing has worked and the phone appears bricked.
How can I resolve this. It must be a common problem, given the millions of these handsets out there. Unfortunately i am currently overseas and in the middle of a desert - so not able to go to a Samsung service centre to get help!
Download UK unbranded firmware from here <http://www.hotfile.com/dl/153177481/9861a3a/I9100XWLP7_I9100XEULP5_XEU.zip.html>. Extract using Winzip. You will get a Tar.md5 file.
Download Odin from here <http://forum.xda-developers.com/attachment.php?attachmentid=725858&d=1316556218>
Completely shutdown Kies via the Task Manager.
Completely Shut Down Phone. Now hold volume down+home+power buttons, You should see a warning asking you to press volume up if you want to continue or volume down to cancel, press volume up. You are now in download mode
Connect your phone to your pc via cable. Fire up Odin. The box below ID:COM will be yellow.
Click on PDA and select the .tar.md5 file extracted in first step.
Click Start. Let Finish. Do not disconnect wire until you see 'Pass'.
If phone bootloops, shut down phone. Now hold volume Up+Home+Power buttons. Do a Factory Reset. Restart.
Let know if this works.
Go to samsung and tell them what happened and they should fix it under warranty
Sent from my GT-I9100 using XDA Premium
If I helped you press thanks!
I knew the kies is not the proper way to update the latest firmware and always giving a problem! When the downloading firmware on kies are almost finish there is always an error such as " hang" or " internet disconnected " ! The smarter way is to use odin3 :good:
Its not a major issue, this isnt a brick, its a softbrick, big difference, just means ya flash failed, could be a million reasons for that,
AS DESCRIBED above, this is a simple fix by downloading and flashing the appropriate stock firmware for your phone via odin again in download mode.
your phone will go to download mode so dont worry about that, if it hasnt gone to dl mode when attempted, pull the battery, leave it out 10 mins, put it back in and try again, failing that a usb jig will suffice, see post on who and where will share their jig if you dont have one, there may be someone near you.
CAUTION, dont try flashing any of the latest leaks on your phone, just choose whatever the last stock release was by your carrier on samfirmware, and flash that as that will be your latest firmware.
I never use kies to update, simply use ota, or download the rom and flash it, kies is very unreliable, this is where HTC and SE beat samsung, the download and recovery methods are so much simpler and they work.
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
mcguirestick said:
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
Click to expand...
Click to collapse
You need to flash a ROM that will wipe your data at once.
Is your phone GT I9100 or GT I9100G?
Jokesy said:
You need to flash a ROM that will wipe your data at once.
Is your phone GT I9100 or GT I9100G?
Click to expand...
Click to collapse
It Is a GT-I9100
mcguirestick said:
It Is a GT-I9100
Click to expand...
Click to collapse
Follow these steps:
1. Download CM9 Resurrection editon
2. Flash CM9 Ressurection edtion via Odin
done.
Let me know how it goes.
Jokesy said:
Follow these steps:
1. Download CM9 Resurrection editon
2. Flash CM9 Ressurection edtion via Odin
done.
Let me know how it goes.
Click to expand...
Click to collapse
Didnt knew roms could be flashed through odin, are they also flashed through the PDA section?
Poroto said:
Didnt knew roms could be flashed through odin, are they also flashed through the PDA section?
Click to expand...
Click to collapse
That is a special .tar edition. You simply flash it just like a single file firmware (as PDA).
Good luck
Jokesy said:
That is a special .tar edition. You simply flash it just like a single file firmware (as PDA).
Good luck
Click to expand...
Click to collapse
Hi Tried it exactly the same im afraid Odin says successful phone reboots then sits at Samsung s2 screen and goes no further
mcguirestick said:
Hi Tried it exactly the same im afraid Odin says successful phone reboots then sits at Samsung s2 screen and goes no further
Click to expand...
Click to collapse
can you enter recovery now?
Jokesy said:
can you enter recovery now?
Click to expand...
Click to collapse
Hi, Nope still can only get to boot load not recovery
mcguirestick said:
Hi, Nope still can only get to boot load not recovery
Click to expand...
Click to collapse
I think your data partition is corrupt, but you can still get it solved.
You need to special .pit file. I'll post you the link (for the .pit file and instructions) very soon
Try this it worked for me
mcguirestick said:
Please please please could anyone help!
About a month ago I upgraded to Ice cream sandwich (LP7) and then rooted my S2. All worked fine for 3 or 4 days and then suddenly it crashed for no reason. I suspect, but am not sure, that it did an automatic update. On rebooting it just stops at the Samsung S2 screen with a yellow triangle.
For the last few weeks i have been trying to find a fix, but am at my wits end now.
I have gone through the different solutions on your site but to no avail also where mine seems to be different is that I can get into boot mode and odin always says its successful. I have tried different pc and usb cable too just in case that was an issue
I can not get into Volume up mode, but i can get into boot mode with volume down. I have tried re loading a few different rom's and Odin says that the transfer was successful each time, however it is still stuck at the same place on reboot.
Tried reloading kernel and re partitioning, and again Odin said it went OK, but still stuck on start screen.
Tried using a jig and turned phone on, but it the phone just went to the start screen again.
If i could just get into reset mode, i could clear the memory, but this is not working either.
If anyone could help i would be very so grateful.
Thanks
Terry
Click to expand...
Click to collapse
Try this
Try this step by step and it shoudl work!
Requirements
A Samsung Galaxy S2 GT-I9100
A Windows PC
Your phone’s USB cable
7-Zip, WinRAR, or any other programs that can extract archive files
Handset USB drivers installed on the PC. You may install the drivers by installing Samsung Kies.
Enable USB Debugging on your handset.
Disable antivirus, firewall, and other security software. Also disable Samsung Kies and other software that accesses your phone. Such software can interfere with the procedure in this guide.
Download the following files to your computer:
Android 4.0.4 ICS firmware build XXLQ5 (I9100XXLQ5_I9100OXALQ5_OXA.zip, 387.1 MB)
copy and paste
hotfile.com/dl/162208594/226b6f0/I9100XXLQ5_I9100OXALQ5_OXA.zip.html
Odin3 1.85 (Odin 1.85.zip,199 kB)
Make sure your phone’s battery is charged up to 75% or more to avoid interruptions during the process.
Backup all personal data on your phone to make sure you have a copy of your personal data (e.g., contacts, SMS, MMS, Internet settings, Wi-Fi passwords, and the like) in case the procedure in this guide erases such data.
For backup tips, check our guides on how to sync your data to the cloud and how to create local backups of your mobile data.
Instructions
Extract the contents of the I9100XXLQ5_I9100OXALQ5_OXA.zip file to get these files:
I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5
GT-I9100-MULTI-CSC-OXALQ5.tar.md5
MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5
u1_02_20120326_emmc_EXT4_8GB.pit
Extract the contents of the Odin 1.85.zip file to obtain the Odin3 v1.85.exe file.
Double-click on the Odin3 v1.85.exe file to launch Odin on your computer.
Unplug your phone from the computer if it is connected. After unplugging, turn your phone off.
Put your phone into Download Mode. To do this, hold the Volume Down, Home, and Power buttons together until the screen turns on. Press the Volume Up key to put your phone into Download Mode.
Connect your phone to the PC using the USB cable. In Odin, a message saying “Added!!†will appear on the bottom left of the window.
In the Odin window, click on the PDA button and select the I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5file. The file should show on the space beside the PDA button.
Click on the PHONE button and select MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5 file. The file should show on the space beside the Phone button.
Click on the CSC button and select the GT-I9100-MULTI-CSC-OXALQ5.tar.md5file. The file should show on the space beside the CSC button.
Don’t alter anything else in Odin. Leave everything else as is, except for adding the files mentioned in steps 7 to 9.
Click on the Start button in Odin to start flashing the firmware to your phone.
After the flashing completes, your phone will automatically reboot. You should be able to get a “PASS†message on the top left part of Odin.
NOTE: If you get a FAIL message or Odin gets stuck, disconnect your phone from the PC and close Odin. Remove the battery from your phone, re-insert it, and place your phone into Download Mode again. Open Odin and do the procedure starting from step 6.
Once you see the Samsung logo on your phone’s screen, you can safely disconnect your phone from the PC.
Hope this helps!
ScottsDesk
ScottsDesk said:
Try this
Try this step by step and it shoudl work!
Requirements
A Samsung Galaxy S2 GT-I9100
A Windows PC
Your phone’s USB cable
7-Zip, WinRAR, or any other programs that can extract archive files
Handset USB drivers installed on the PC. You may install the drivers by installing Samsung Kies.
Enable USB Debugging on your handset.
Disable antivirus, firewall, and other security software. Also disable Samsung Kies and other software that accesses your phone. Such software can interfere with the procedure in this guide.
Download the following files to your computer:
Android 4.0.4 ICS firmware build XXLQ5 (I9100XXLQ5_I9100OXALQ5_OXA.zip, 387.1 MB)
copy and paste
hotfile.com/dl/162208594/226b6f0/I9100XXLQ5_I9100OXALQ5_OXA.zip.html
Odin3 1.85 (Odin 1.85.zip,199 kB)
Make sure your phone’s battery is charged up to 75% or more to avoid interruptions during the process.
Backup all personal data on your phone to make sure you have a copy of your personal data (e.g., contacts, SMS, MMS, Internet settings, Wi-Fi passwords, and the like) in case the procedure in this guide erases such data.
For backup tips, check our guides on how to sync your data to the cloud and how to create local backups of your mobile data.
Instructions
Extract the contents of the I9100XXLQ5_I9100OXALQ5_OXA.zip file to get these files:
I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5
GT-I9100-MULTI-CSC-OXALQ5.tar.md5
MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5
u1_02_20120326_emmc_EXT4_8GB.pit
Extract the contents of the Odin 1.85.zip file to obtain the Odin3 v1.85.exe file.
Double-click on the Odin3 v1.85.exe file to launch Odin on your computer.
Unplug your phone from the computer if it is connected. After unplugging, turn your phone off.
Put your phone into Download Mode. To do this, hold the Volume Down, Home, and Power buttons together until the screen turns on. Press the Volume Up key to put your phone into Download Mode.
Connect your phone to the PC using the USB cable. In Odin, a message saying “Added!!†will appear on the bottom left of the window.
In the Odin window, click on the PDA button and select the I9100_CODE_I9100XXLQ5_CL753921_REV02_user_low_ship.tar.md5file. The file should show on the space beside the PDA button.
Click on the PHONE button and select MODEM_I9100XXLQ5_REV_02_CL1165929.tar.md5 file. The file should show on the space beside the Phone button.
Click on the CSC button and select the GT-I9100-MULTI-CSC-OXALQ5.tar.md5file. The file should show on the space beside the CSC button.
Don’t alter anything else in Odin. Leave everything else as is, except for adding the files mentioned in steps 7 to 9.
Click on the Start button in Odin to start flashing the firmware to your phone.
After the flashing completes, your phone will automatically reboot. You should be able to get a “PASS†message on the top left part of Odin.
NOTE: If you get a FAIL message or Odin gets stuck, disconnect your phone from the PC and close Odin. Remove the battery from your phone, re-insert it, and place your phone into Download Mode again. Open Odin and do the procedure starting from step 6.
Once you see the Samsung logo on your phone’s screen, you can safely disconnect your phone from the PC.
Hope this helps!
ScottsDesk
Click to expand...
Click to collapse
Hi Tried it again no luck
mcguirestick said:
Hi Tried it again no luck
Click to expand...
Click to collapse
Sorry for not posting the link for the .pit file.
You can get the pit file here
Use the stock pit file first before trying the patched ones.
Follow the guide in this thread to revive your phone
Good luck
Jokesy said:
Sorry for not posting the link for the .pit file.
You can get the pit file here
Use the stock pit file first before trying the patched ones.
Follow the guide in this thread to revive your phone
Good luck
Click to expand...
Click to collapse
Shall we try the pit by itself or the pit with the rom
//
I belive we have the same problems:
http://forum.xda-developers.com/showthread.php?p=32546472#post32546472 (now that my phone flashs - page 2 -)
marceloasr said:
Shall we try the pit by itself or the pit with the rom
//
I belive we have the same problems:
http://forum.xda-developers.com/showthread.php?p=32546472#post32546472 (now that my phone flashs - page 2 -)
Click to expand...
Click to collapse
his case is milder than yours. he should get his problem fixed by follow the tutorial i posted.
TRY THIS!
mcguirestick said:
Hi Tried it again no luck
Click to expand...
Click to collapse
Try this I did and it worked to get mine booting after a bad update.
I messed around with it using several methods of getting it to boot into download mode until I finally got it to do it. I think I left it plugged into the USB, powered it down until I saw the charging screen, then I proceeded to play with the different ways to hold the buttons to get it to download mode. If you are persistent enough and read a little on booting methods to get bricked phone into download mode you will succed if not then your not for the world of trial and error... the main thing is do the first steps I said before until it works
1. Get into Download Mode (WITH THE PHONE PLUGGED IN) by following the steps below
*Turn off the phone until you get to the charging battery screen (keep in mind, your phone is currently PLUGGED IN)
*Press volume up and down, and power all at once.
*As soon as the screen turns black, release your power button.
2. Unplug phone from USB
or try
2. Remove everything from your phone (SD card, sim, battery).
3. Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
4. Press and HOLD vol. up and vol. down.
5. As you are HOLDING these buttons, reattach your battery.
6. You should be in Download Mode.
7. Unplug phone from USB
any how try try try until it works
Once in download mode
Get your files together for your phone, and use Odin 1.85.
Plug into Odin and make sure it shows yellow and its added!
1. Now if your files have like 3 files and the exact .pit file for your phone if available.
I found mine here (Find yous stock firmware for your phone)
CLICK HERE
2. Click the PIT button and browse to your exact .pit file for your phone *It should now have added a check in the re-partition box under the options area of the Odin window. If not CHECK IT!
***If you don't have your .pit don't worry about this unless you suspect, or have a bad partition
3. If you have just 1 file just click the PDA button and load the file. If you have 3 then you will load the PDA file in PDA, the Modem file into PHONE, and the CSC file into CSC, there are way too many phones to link all the files so get you stuff together!
4. Now hit start.
5. When done and the phone shows the first sign of starting up IE Logo or whatever... immediately unplug the battery from the phone to shut it down.
6. Now put it back in and start it in Upload mode by pressing Vol Up, Home at the same time then the Power button.
7. As soon as the phone shows the first sign of starting up IE Logo or whatever let go of all buttons and using the Vol Up down Choose the Clear Cache option and go through and make sure you factory reset it if you can just for good measure.
8. Reboot
9. Now when the phone shows the first sign of starting up IE Logo or whatever take out battery again to power off
10. Now put it back in and start it in Download mode by pressing Vol Down, Home at the same time then the Power button.
11. Once in download mode Hook up to Odin again and flash it with a root kernel for your phone. Do not ask me just find it. I did it took time but I got all the files together over several days of reading and collecting the correct ones.
12. When done and the phone shows the first sign of starting up IE Logo or whatever... immediately unplug the battery from the phone to shut it down.
13. Now put it back in and start it in Upload mode by pressing Vol Up, Home at the same time then the Power button.
14. In most roots you will now have a advanced or mounting options and more options to use.
15. I cleared the Cache again, Cleared the Davilik Cache, Went into a option and actually mounted the cache formatted the Cache.
16. Use the option now to restart the phone...
And mine started up installed the apps and I am up and running, nice and smooth and no issues so far
I hope this helps out someone whos just about to go off the deep end, as I was there and patience and trial and error came up with this step by step way to recover mine. Thank me by hitting the little thumbs up THANKS button below this post.
And if your so happy your phone is up show your appreciation by buying me a Pepsi
Jokesy said:
his case is milder than yours. he should get his problem fixed by follow the tutorial i posted.
Click to expand...
Click to collapse
Hi Once again no luck,
I have sent it away to go on a JTAG box will let you know if that fixes it.
I really appreciate all your help.
I will let you know what happens.
thanks
Terry
mcguirestick said:
Hi Once again no luck,
I have sent it away to go on a JTAG box will let you know if that fixes it.
I really appreciate all your help.
I will let you know what happens.
thanks
Terry
Click to expand...
Click to collapse
Sorry for your luck! Cheers!
Try this I did and it worked to get mine booting after a bad update.
I messed around with it using several methods of getting it to boot into download mode until I finally got it to do it. I think I left it plugged into the USB, powered it down until I saw the charging screen, then I proceeded to play with the different ways to hold the buttons to get it to download mode. If you are persistent enough and read a little on booting methods to get bricked phone into download mode you will succed if not then your not for the world of trial and error... the main thing is do the first steps I said before until it works
1. Get into Download Mode (WITH THE PHONE PLUGGED IN) by following the steps below
*Turn off the phone until you get to the charging battery screen (keep in mind, your phone is currently PLUGGED IN)
*Press volume up and down, and power all at once.
*As soon as the screen turns black, release your power button.
2. Unplug phone from USB
or try
2. Remove everything from your phone (SD card, sim, battery).
3. Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
4. Press and HOLD vol. up and vol. down.
5. As you are HOLDING these buttons, reattach your battery.
6. You should be in Download Mode.
7. Unplug phone from USB
any how try try try until it works
Once in download mode
Get your files together for your phone, and use Odin 1.85.
Plug into Odin and make sure it shows yellow and its added!
1. Now if your files have like 3 files and the exact .pit file for your phone
I found mine here
http://www.droidevelopers.com/showthread.php?11722-Download-OPS-amp-PIT-files
2. Click the PIT button and browse to your exact .pit file for your phone *It should now have added a check in the re-partition box under the options area of the Odin window. If not CHECK IT!
***If you don't have your .pit don't worry about this unless you suspect, or have a bad partition
3. If you have just 1 file just click the PDA button and load the file. If you have 3 then you will load the PDA file in PDA, the Modem file into PHONE, and the CSC file into CSC, there are way too many phones to link all the files so get you stuff together!
4. Now hit start.
5. When done and the phone shows the first sign of starting up IE Logo or whatever... immediately unplug the battery from the phone to shut it down.
6. Now put it back in and start it in Upload mode by pressing Vol Up, Home at the same time then the Power button.
7. As soon as the phone shows the first sign of starting up IE Logo or whatever let go of all buttons and using the Vol Up down Choose the Clear Cache option and go through and make sure you factory reset it if you can just for good measure.
8. Reboot
9. Now when the phone shows the first sign of starting up IE Logo or whatever take out battery again to power off
10. Now put it back in and start it in Download mode by pressing Vol Down, Home at the same time then the Power button.
11. Once in download mode Hook up to Odin again and flash it with a root kernel for your phone. Do not ask me just find it. I did it took time but I got all the files together over several days of reading and collecting the correct ones.
12. When done and the phone shows the first sign of starting up IE Logo or whatever... immediately unplug the battery from the phone to shut it down.
13. Now put it back in and start it in Upload mode by pressing Vol Up, Home at the same time then the Power button.
14. In most roots you will now have a advanced or mounting options and more options to use.
15. I cleared the Cache again, Cleared the Davilik Cache, Went into a option and actually mounted the cache formatted the Cache.
16. Use the option now to restart the phone...
And mine started up installed the apps and I am up and running, nice and smooth and no issues so far
I hope this helps out someone whos just about to go off the deep end, as I was there and patience and trial and error came up with this step by step way to recover mine. Thank me by hitting the little thumbs up THANKS button below this post.
And if your so happy your phone is up show your appreciation by buying me a Pepsi
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=E6M7UWKCZYSNE
scottsdesk
My Tab S6 tried to auto-install an update yesterday (it is rarely connected to Wifi/internet). It then rebooted. Since then, it's been stuck in a boot loop.
It will display the "Samsung Galaxy Tab S6 | Secured By Knox" logo screen for a few seconds, then switch to the blue "Installing System Update" screen (with the android logo). Installing System Update gets to 28% and stops. Then the rotating icon on the android freezes. Then the device reboots and starts all over again.
Edit: the tablet is 100% stock. It's not been rooted or had any custom ROMs loaded.
I have tried getting to recovery mode, by holding power+volup while it boots. This doesn't seem to change the behavior at all. Any advice is much appreciated.
Fedge7 said:
My Tab S6 tried to auto-install an update yesterday (it is rarely connected to Wifi/internet). It then rebooted. Since then, it's been stuck in a boot loop.
It will display the "Samsung Galaxy Tab S6 | Secured By Knox" logo screen for a few seconds, then switch to the blue "Installing System Update" screen (with the android logo). Installing System Update gets to 28% and stops. Then the rotating icon on the android freezes. Then the device reboots and starts all over again.
Edit: the tablet is 100% stock. It's not been rooted or had any custom ROMs loaded.
I have tried getting to recovery mode, by holding power+volup while it boots. This doesn't seem to change the behavior at all. Any advice is much appreciated.
Click to expand...
Click to collapse
can you shut it down? try volume down and power button ? if it don't shut down, do this soon as it reboots, hold volume up and down and plug in usb cable to desktop/laptop usb port! it will boot into download mode!
N1NJATH3ORY said:
can you shut it down? try volume down and power button ? if it don't shut down, do this soon as it reboots, hold volume up and down and plug in usb cable to desktop/laptop usb port! it will boot into download mode!
Click to expand...
Click to collapse
I can't actually shut it down. If I start holding power+voldown right after it boots, the tablet does reboot before getting stuck at 28%. But it reboots--it doesn't power off.
I tried download mode and that actually seemed to work! Specifically, I left the tablet overnight in the reboot loop until the battery drained. Just now, I held down volup+voldown and plugged it into my laptop. I got the green "Warning/Custom OS" screen and then pressed volup to continue. The tablet rebooted pretty quickly after that (I'm guessing due to low battery) so I didn't get a good look at the download mode options.
Once I'm in download mode, can I factory reset the tablet? I don't need to preserve any data/apps/settings.
Fedge7 said:
I can't actually shut it down. If I start holding power+voldown right after it boots, the tablet does reboot before getting stuck at 28%. But it reboots--it doesn't power off.
I tried download mode and that actually seemed to work! Specifically, I left the tablet overnight in the reboot loop until the battery drained. Just now, I held down volup+voldown and plugged it into my laptop. I got the green "Warning/Custom OS" screen and then pressed volup to continue. The tablet rebooted pretty quickly after that (I'm guessing due to low battery) so I didn't get a good look at the download mode options.
Once I'm in download mode, can I factory reset the tablet? I don't need to preserve any data/apps/settings.
Click to expand...
Click to collapse
You cannot reset the tablet from Download mode afaik- You need to enter Recovery Mode to do that.
You can however, flash stock from Download mode using Odin (3.13.3 is best). If you're not confident with doing that, your best option is Factory Reset in Recovery Mode. Hold Volume Up and Power when the Tablet is booting, let go when you see the Samsung logo. The timing can be tricky, but you should be able to do it. Also, you can force a reboot with Volume Down and Power.
Alternatively, if factory reset doesn't work, since you're completely stock, you will still be covered under warrenty.
bartleby999 said:
your best option is Factory Reset in Recovery Mode. Hold Volume Up and Power when the Tablet is booting, let go when you see the Samsung logo.
Click to expand...
Click to collapse
Thanks for the suggestion. I have tried this many many times. I've tried letting go of the buttons at different times. I've tried holding volup while letting go of power. I've tried this a ton of different ways, and no matter what, the tablet always shows the "Installing system update" screen. Some googling has led me to believe that sometimes, when performing a factory reset, the "Installing system update" screen shows up right before the normal recovery screen. Is it possible that the tablet is trying to get to recovery mode, but can't get past this first step?
Fedge7 said:
Is it possible that the tablet is trying to get to recovery mode, but can't get past this first step?
Click to expand...
Click to collapse
Honestly, I don't know - I'm not an expert but I guess it's possible that the update failed and corrupted both System and Recovery.
You'll be covered under warrenty, so maybe just return the Tablet from where you purchased or direct to Samsung, could take a while given the current situation though I guess. If you have a PC, then I think the best option would be to just flash stock yourself, since that's probably all Samsung will do. Even if that doesn't work you'd still be covered under warrenty, as far as I'm aware attempting to flash stock doesn't trip Knox.
Here is solution to unbrick your device!!!
Fedge7 said:
My Tab S6 tried to auto-install an update yesterday (it is rarely connected to Wifi/internet). It then rebooted. Since then, it's been stuck in a boot loop.
...
Edit: the tablet is 100% stock. It's not been rooted or had any custom ROMs loaded.
I have tried getting to recovery mode, by holding power+volup while it boots. This doesn't seem to change the behavior at all. Any advice is much appreciated.
Click to expand...
Click to collapse
Despair not...I have just come from resolving this exact situation not 30 minutes ago. I'd been trying to flash (using Odin as I decided to stay on Stock and not root this device, for a change) the latest OneUI2.1 releases for my device (SM-T865 - LTE version) and boom in the middle of the Odin update, the flash just failed...I then couldn't reboot and get into neither Recovery, nor Download Mode because it appears my bootloader and recovery both got corrupted.
Here's what you need....
1. Odin app for PC (am on Windows)
2. Your device's Stock firmware (sammobile firmware archive)
3. You will need someone to help you boot the device directly into Download mode (and this is the tricky part because for most of us we are used to get into Bootloader by using the key combination (from Powered Off device) Vol+ and Power On at the same time to get into stock recovery and then scrolling down to option 2 in this menu, "Reboot to Bootloader". Well now you are going to boot directly into Bootloader mode. Here's how you do it...
4. Get your friend to line up the USB-C cable into the port of the device, but DO NOT press it in...yet
5. Press Power off and Vol- buttons at the same time to turn off the device
6. And now you have to to be super fast: if device starts to turn on on its own, YOU press and hold Vol+ and Vol- both at the same time while YOUR FRIEND pushes the USB cable fully into the port - you should now have booted directly into Download mode. (if not repeat this, and remember to be super fast and sync with your friend pushing in the USB cable)...
7. When you get into Download mode, then you are home and dry...
8. Select ONLY the Bootloader file (BL...XX...) in Odin, make sure only "reset time" and "reboot" are ticked, and flash
9. When device reboots, press Vol+ and Power combo to get back into Bootloader mode again...but I think device will reboot into Download mode on its own
10. Now select all the files from your Stock file into the various tabs (BL, CP, CSC, AP...) do not select HOME_CSC as we want to flush this device clean...
11. Flash, and voila...success - you will have lost all your data but rather that than losing the device...
12. Feedback here and let us know if this works? For reference for others in the future...
FYI, I got in this situation, and the previous post did work for me, just takes good timing! Thanks!!!!
Same issue today for me. My tablet showed different screen with green and red text, it allowed me to delete app data, then booted into safe mode, then i had to do factory reset and now i am screwed, as it is refusing to restore any apps and their settings. I will try to flash it back to Android 9, maybe then it will do the restore. I forgot to do any manual backup to SD or so.
Edit: the device upgraded to 10, but reset itself after about 10 minutes of use.
Edit2: i found what caused it. It is caused by Nova Launcher, if i try to set wallpaper.
Just found a news article that there is a RGB/sRGB problem with wallpapers. It might be the problem i had.
I am adding a screenshot of the result.
Yeah, I had that kind of reboot loop from a wallpaper that I downloaded
Moe5508 said:
Here is solution to unbrick your device!!!
Despair not...I have just come from resolving this exact situation not 30 minutes ago. I'd been trying to flash (using Odin as I decided to stay on Stock and not root this device, for a change) the latest OneUI2.1 releases for my device (SM-T865 - LTE version) and boom in the middle of the Odin update, the flash just failed...I then couldn't reboot and get into neither Recovery, nor Download Mode because it appears my bootloader and recovery both got corrupted.
Here's what you need....
1. Odin app for PC (am on Windows)
2. Your device's Stock firmware (sammobile firmware archive)
3. You will need someone to help you boot the device directly into Download mode (and this is the tricky part because for most of us we are used to get into Bootloader by using the key combination (from Powered Off device) Vol+ and Power On at the same time to get into stock recovery and then scrolling down to option 2 in this menu, "Reboot to Bootloader". Well now you are going to boot directly into Bootloader mode. Here's how you do it...
4. Get your friend to line up the USB-C cable into the port of the device, but DO NOT press it in...yet
5. Press Power off and Vol- buttons at the same time to turn off the device
6. And now you have to to be super fast: if device starts to turn on on its own, YOU press and hold Vol+ and Vol- both at the same time while YOUR FRIEND pushes the USB cable fully into the port - you should now have booted directly into Download mode. (if not repeat this, and remember to be super fast and sync with your friend pushing in the USB cable)...
7. When you get into Download mode, then you are home and dry...
8. Select ONLY the Bootloader file (BL...XX...) in Odin, make sure only "reset time" and "reboot" are ticked, and flash
9. When device reboots, press Vol+ and Power combo to get back into Bootloader mode again...but I think device will reboot into Download mode on its own
10. Now select all the files from your Stock file into the various tabs (BL, CP, CSC, AP...) do not select HOME_CSC as we want to flush this device clean...
11. Flash, and voila...success - you will have lost all your data but rather that than losing the device...
12. Feedback here and let us know if this works? For reference for others in the future...
Click to expand...
Click to collapse
Bravo!!
Works for me.
Many thanks
I can get into download mode. But it kicks me out within a few seconds. Any help please
Moe5508 said:
Here is solution to unbrick your device!!!
Despair not...I have just come from resolving this exact situation not 30 minutes ago. I'd been trying to flash (using Odin as I decided to stay on Stock and not root this device, for a change) the latest OneUI2.1 releases for my device (SM-T865 - LTE version) and boom in the middle of the Odin update, the flash just failed...I then couldn't reboot and get into neither Recovery, nor Download Mode because it appears my bootloader and recovery both got corrupted.
Here's what you need....
1. Odin app for PC (am on Windows)
2. Your device's Stock firmware (sammobile firmware archive)
3. You will need someone to help you boot the device directly into Download mode (and this is the tricky part because for most of us we are used to get into Bootloader by using the key combination (from Powered Off device) Vol+ and Power On at the same time to get into stock recovery and then scrolling down to option 2 in this menu, "Reboot to Bootloader". Well now you are going to boot directly into Bootloader mode. Here's how you do it...
4. Get your friend to line up the USB-C cable into the port of the device, but DO NOT press it in...yet
5. Press Power off and Vol- buttons at the same time to turn off the device
6. And now you have to to be super fast: if device starts to turn on on its own, YOU press and hold Vol+ and Vol- both at the same time while YOUR FRIEND pushes the USB cable fully into the port - you should now have booted directly into Download mode. (if not repeat this, and remember to be super fast and sync with your friend pushing in the USB cable)...
7. When you get into Download mode, then you are home and dry...
8. Select ONLY the Bootloader file (BL...XX...) in Odin, make sure only "reset time" and "reboot" are ticked, and flash
9. When device reboots, press Vol+ and Power combo to get back into Bootloader mode again...but I think device will reboot into Download mode on its own
10. Now select all the files from your Stock file into the various tabs (BL, CP, CSC, AP...) do not select HOME_CSC as we want to flush this device clean...
11. Flash, and voila...success - you will have lost all your data but rather that than losing the device...
12. Feedback here and let us know if this works? For reference for others in the future...
Click to expand...
Click to collapse
Hi,
Really need your help, after I updated my firmware using Odin, updated BL, AP, CP, CSC, my tab cannot boot up stuck in logo. Doing the Power + volume up leads me to different screen now. I cannot access recovery mode or download page anymore,
What must I do? Pleasssee help. Added the pic, after doing hard reset (power + vol up)
I cannot connect back to Odin also. Always setup connection failed.
Please help. Really messed up big time
Just a thought... Can this be restored from service center?
Thank you in advance.
I have the same problem with a Tab S6 Lite, it is in bootloop and does not let me enter the recovery mode, I can go into download mode and I flashed the latest original firmware Android11, Android10 etc., . I tried them all but always goes in bootloop, and also the bootloop occurs only if I connect the usb cable to the PC, without any sign of life. Do I still have hopes or have I compromised the motherboard?
The reason for all this is because I had followed a guide to give root permissions with magisk, I did everything right, only that the guide was with Android10, while I had Android11 and I was deceived by the fact that in the title of the guide there was written "guide 2021"
, so I did not check the compatibility of operating systems, I was a fool, I know, I hope so much that I did nothing irretrievable, it's my son's tablet!
Genpis said:
I have the same problem with a Tab S6 Lite, it is in bootloop and does not let me enter the recovery mode, I can go into download mode and I flashed the latest original firmware Android11, Android10 etc., . I tried them all but always goes in bootloop, and also the bootloop occurs only if I connect the usb cable to the PC, without any sign of life. Do I still have hopes or have I compromised the motherboard?
The reason for all this is because I had followed a guide to give root permissions with magisk, I did everything right, only that the guide was with Android10, while I had Android11 and I was deceived by the fact that in the title of the guide there was written "guide 2021"
, so I did not check the compatibility of operating systems, I was a fool, I know, I hope so much that I did nothing irretrievable, it's my son's tablet!
Click to expand...
Click to collapse
Did you use HOME CSC or the non HOME CSC when flashing?
Genpis said:
I have the same problem with a Tab S6 Lite, it is in bootloop and does not let me enter the recovery mode, I can go into download mode and I flashed the latest original firmware Android11, Android10 etc., . I tried them all but always goes in bootloop, and also the bootloop occurs only if I connect the usb cable to the PC, without any sign of life. Do I still have hopes or have I compromised the motherboard?
The reason for all this is because I had followed a guide to give root permissions with magisk, I did everything right, only that the guide was with Android10, while I had Android11 and I was deceived by the fact that in the title of the guide there was written "guide 2021"
, so I did not check the compatibility of operating systems, I was a fool, I know, I hope so much that I did nothing irretrievable, it's my son's tablet!
Click to expand...
Click to collapse
Try to install a castom rooted rom which has pre installed also Twrp.
[MAGISK Rom / Firmware base convertor) 420rom-T860/5 - V13.3- CUE1 - ANDROID 10 - OneUI 3.1 - Sec Patch 05/2021 - Released 06/07/2021
WELCOME TO 420 ROM - MAGISK ROM FOR SAMSUNG GALAXY TAB S6 WiFi/4G (T860/5)! 420rom Telegram-Group: Please bear in mind that things will be added as and when my learning and time permits (being a dad with a family and having ADHD myself means...
forum.xda-developers.com
Download the android 11 last rooted rom from there. You install it with odin as as a normal original rom.
Disable in odin auto reboot. After rom install, restart manually and press the correct buttons immediately to boot in Twrp and not to system. Format (not wipe) data from there and reboot to system. If you are lucky it will work..
(I hope you unlocked bootloader before try to root. If you haven't unlocked bootloader this won't work also).
Moe5508 said:
Here is solution to unbrick your device!!!
Despair not...I have just come from resolving this exact situation not 30 minutes ago. I'd been trying to flash (using Odin as I decided to stay on Stock and not root this device, for a change) the latest OneUI2.1 releases for my device (SM-T865 - LTE version) and boom in the middle of the Odin update, the flash just failed...I then couldn't reboot and get into neither Recovery, nor Download Mode because it appears my bootloader and recovery both got corrupted.
Here's what you need....
1. Odin app for PC (am on Windows)
2. Your device's Stock firmware (sammobile firmware archive)
3. You will need someone to help you boot the device directly into Download mode (and this is the tricky part because for most of us we are used to get into Bootloader by using the key combination (from Powered Off device) Vol+ and Power On at the same time to get into stock recovery and then scrolling down to option 2 in this menu, "Reboot to Bootloader". Well now you are going to boot directly into Bootloader mode. Here's how you do it...
4. Get your friend to line up the USB-C cable into the port of the device, but DO NOT press it in...yet
5. Press Power off and Vol- buttons at the same time to turn off the device
6. And now you have to to be super fast: if device starts to turn on on its own, YOU press and hold Vol+ and Vol- both at the same time while YOUR FRIEND pushes the USB cable fully into the port - you should now have booted directly into Download mode. (if not repeat this, and remember to be super fast and sync with your friend pushing in the USB cable)...
7. When you get into Download mode, then you are home and dry...
8. Select ONLY the Bootloader file (BL...XX...) in Odin, make sure only "reset time" and "reboot" are ticked, and flash
9. When device reboots, press Vol+ and Power combo to get back into Bootloader mode again...but I think device will reboot into Download mode on its own
10. Now select all the files from your Stock file into the various tabs (BL, CP, CSC, AP...) do not select HOME_CSC as we want to flush this device clean...
11. Flash, and voila...success - you will have lost all your data but rather that than losing the device...
12. Feedback here and let us know if this works? For reference for others in the future...
Click to expand...
Click to collapse
Why flashing only the bootloader first? At the moment I'm trying to recover my s20 fe from a bootloop without losing my data
sosimple said:
Try to install a castom rooted rom which has pre installed also Twrp.
[MAGISK Rom / Firmware base convertor) 420rom-T860/5 - V13.3- CUE1 - ANDROID 10 - OneUI 3.1 - Sec Patch 05/2021 - Released 06/07/2021
WELCOME TO 420 ROM - MAGISK ROM FOR SAMSUNG GALAXY TAB S6 WiFi/4G (T860/5)! 420rom Telegram-Group: Please bear in mind that things will be added as and when my learning and time permits (being a dad with a family and having ADHD myself means...
forum.xda-developers.com
Download the android 11 last rooted rom from there. You install it with odin as as a normal original rom.
Disable in odin auto reboot. After rom install, restart manually and press the correct buttons immediately to boot in Twrp and not to system. Format (not wipe) data from there and reboot to system. If you are lucky it will work..
(I hope you unlocked bootloader before try to root. If you haven't unlocked bootloader this won't work also).
Click to expand...
Click to collapse
Any tips in recovering my stock s20 fe from a bootloop without losing data? already tried Odin but without success the first try
jointer said:
Same issue today for me. My tablet showed different screen with green and red text, it allowed me to delete app data, then booted into safe mode, then i had to do factory reset and now i am screwed, as it is refusing to restore any apps and their settings. I will try to flash it back to Android 9, maybe then it will do the restore. I forgot to do any manual backup to SD or so.
Edit: the device upgraded to 10, but reset itself after about 10 minutes of use.
Edit2: i found what caused it. It is caused by Nova Launcher, if i try to set wallpaper.
Click to expand...
Click to collapse
did you managed to not lose your data?
jrdef said:
Any tips in recovering my stock s20 fe from a bootloop without losing data? already tried Odin but without success the first try
Click to expand...
Click to collapse
Wiping cache partition in Recovery and reflashing the firmware are basically your only 2 options
jrdef said:
Any tips in recovering my stock s20 fe from a bootloop without losing data? already tried Odin but without success the first try
Click to expand...
Click to collapse
Flash in odin the same rom you had. There are 2 csc files in rom, which you use 1 in odin one. Try use the "home csc". Home csc keep KEEPS your data. If you're lucky it may work. (It would work in keeping your data 100% if your rom was ok. Because it isn't you have some changes to work.).
You must try with same rom or newer.
CSC – If you flash the CSC file, it’ll perform a factory reset of your Galaxy device and wipe all data while installing a new firmware to bring your device to the same state as it was when you purchased it. Go with CSC if you want a clean installation.
HOME_CSC – On the other hand, if you want to keep your Samsung phone’s data and settings even flashing the stock firmware, you can select the HOME_CSC file.