Hi, after trying out some custom roms like CM9-10 and Omega my phone suddenly started rebooting. It lets me enter the PIN and starts up but after a qouple of seconds it reboots again.
The wierd part is that it autostarts after I insert the battery, but I can enter both CWM and Download mode.
I have tried enter CWM and do a wipe but phone reboots in the middle of the process, same goes when trying to flash CM9 or any other rom I have on the internal SD.
I have also tried following a Swedish guide to restore it to stock using Odin, but after adding the PDA and pressing start I get a Fail in Odin to, something about NAND write fails.
Does anyone have a solution for me? Should I tick re-partition or do something other in Odin?
I would suggest boot into recovery. Wipe Dalvik cache. Flash Rom. Wipe both caches. reboot.
Sent from my GT-I9300 using xda premium
Do you have international galaxy s3 (gt-i9300)?
jnr21 said:
Do you have international galaxy s3 (gt-i9300)?
Click to expand...
Click to collapse
Well I think so, it was sold in Sweden.
The problem is that it reboots doing most of the actions in CWM, I think I have managed to wipe Dalvik but as soon as I try to install a rom it just reboots.
I also tried rooting again using Odin 1.85 but it fails with that version too.
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
burton6666 said:
Well I think so, it was sold in Sweden.
The problem is that it reboots doing most of the actions in CWM, I think I have managed to wipe Dalvik but as soon as I try to install a rom it just reboots.
I also tried rooting again using Odin 1.85 but it fails with that version too.
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Click to expand...
Click to collapse
If all else fails get yourself a S3 USB Jig. I bought one, funnily enough it arrived today from Hong Kong and it only cost something like 2,50€ delivered free. Then install a stock rom.
burton6666 said:
Hi, after trying out some custom roms like CM9-10 and Omega my phone suddenly started rebooting. It lets me enter the PIN and starts up but after a qouple of seconds it reboots again.
The wierd part is that it autostarts after I insert the battery, but I can enter both CWM and Download mode.
I have tried enter CWM and do a wipe but phone reboots in the middle of the process, same goes when trying to flash CM9 or any other rom I have on the internal SD.
I have also tried following a Swedish guide to restore it to stock using Odin, but after adding the PDA and pressing start I get a Fail in Odin to, something about NAND write fails.
Does anyone have a solution for me? Should I tick re-partition or do something other in Odin?
Click to expand...
Click to collapse
If your Nand is corrupt i dont think you can get out of it......99 percent of the time if you can get into download mode your good. but if you having Nand Write issues, i dont know if there is a coming back from that.
hope thats not the case and another member can shed some better light on the subject.
Nand. See posts regarding. PIT today.
jje
Sent from my GT-I9300 using xda premium
JJEgan said:
Nand. See posts regarding. PIT today.
jje
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
Could you post a link to that thread? I found this one and have tried flashing some of the PIT-files but it does not work. Or should I flash some other files at the same time?
Ok, following one guide witch seams to fix my problem is that I need a 3-part firmware. Every Firmware I have downloaded contains:
boot, cache, hidden, modem, recovery, system -if I extract them one extra time. Is that right? Where should I load them in odin in that case? If not could anyone direct me to a download-page for 3-part firmwares? (I downloaded the last one from samfirmware.com)
It is very strange that the core functions kind of work as I can boot normaly into the system and even run an app if I am fast, then reboot.
Downloadmode works untill I try to flash something.
CWM works until I try to do a Wipe or flash a rom, I can wipe dalvik and some other stuff, but not cache, data and some other. I noticed that You could partition sdcard from CWM should I try that? and if so what should i select in the next screen about partition size?
Related
hello,,
i have a problem with my galaxy s3 GT-I9300
the problem is that i flashed MIUI and it worked perfectly .. after that restarted my device and it repeat restarting.
so i got to recovery mode and it failed to flash any zip file. and failed to wipe to factory reset and failed to wipe data.
i was on CWM touch 5.0.5 but someone here adviced me to flash Philez Touch and after that i couldn't access recovery anymore
i tried to flash from odin a stock rom
Code:
I9300XXELLB_I9300OJVELL3_I9300XXELLA_HOME.tar.md5
and here is the result
Code:
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> tz.img
<ID:0/005> NAND Write Start!!
<ID:0/005> sboot.bin
<ID:0/005> system.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The Download screen says the following
Code:
ODIN MODE
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: YES (5 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
Downloading..
this is all i have .. please help me
thanks in advance
not SDS. probably some kinda loose connection of usb. happened to me many times! tried all the ports?
sent from GS3 running MOKEE CM10.1 NIGHTLY RC3
sriram231092 said:
not SDS. probably some kinda loose connection of usb. happened to me many times! tried all the ports?
sent from GS3 running MOKEE CM10.1 NIGHTLY RC3
Click to expand...
Click to collapse
tried all ports.
killed all samsung kies processes.
the problem is that i flashed a recovery file and it works but when flashing any rom it stuck !!!
Same answer nand damaged take to a service centre .
jje
JJEgan said:
Same answer nand damaged take to a service centre .
jje
Click to expand...
Click to collapse
flashing
Code:
recovery-cwmtouch-6.0.3.2-GTI9300.tar
result to successful
Code:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
Have you tried flashing with separate files and pit file ? This should rewrite your partitions. Such "more parted" can be found here on XDA or sammobile.
Sent from my GT-I9300 using xda premium
JJEgan said:
Same answer nand damaged take to a service centre .
jje
Click to expand...
Click to collapse
ground-zero said:
Have you tried flashing with separate files and pit file ? This should rewrite your partitions. Such "more parted" can be found here on XDA or sammobile.
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
can you please provide me the link
thanks
eng.helewa said:
can you please provide me the link
thanks
Click to expand...
Click to collapse
Follow the steps in this thread.
If boots, then good, if not, then try flashing an ICS firmware. Download from Sammobile.
eng.helewa said:
can you please provide me the link
thanks
Click to expand...
Click to collapse
hey guys
i have flashed a rom finally though odin .. but the device still restarting and can't reach recovery mode
The NAND stuck problem caused by improper pit file .. i changed my pit file and it worked.
but why it still restarting ?!
here is what i did: flashed
Code:
[B]The ROM:[/B] I9300XXELLB_I9300OJVELL3_I9300XXELLA_HOME.tar.md5
[B]The PIT FILE:[/B] M0_20120220.pit
Note that the rom wont flash without the pit file
I had a similar problem with my I9305, would die at 23% of system.img. Fixed by re-flashing using Heimdall - after that, Odin also works again. Apparently a bug in Odin.
(However, in my case, the problem was not caused by repartitioning, nor did I need a PIT file to fix it.)
Sent from my GT-I9305 using xda app-developers app
eng.helewa said:
hey guys
i have flashed a rom finally though odin .. but the device still restarting and can't reach recovery mode
The NAND stuck problem caused by improper pit file .. i changed my pit file and it worked.
but why it still restarting ?!
here is what i did: flashed
Code:
[B]The ROM:[/B] I9300XXELLB_I9300OJVELL3_I9300XXELLA_HOME.tar.md5
[B]The PIT FILE:[/B] M0_20120220.pit
Note that the rom wont flash without the pit file
Click to expand...
Click to collapse
Have you flashed a firmware with single CSC, modem, code files ? When you make a repartition this is necessary. And you can try an other Odin vetsion. I use permanently 1.84 or change to Heimdall.
Hope this works !
Sent from my GT-I9300 using xda premium
Hi, could anyone tell me please what i can do with bootlooping S3? It happened on version of CM11 rom, it was workin fine until this one time i plug it to charge it and from then it is just staying on galaxy S3 logo. I can get to download mode and recovery mode but odin wont flash anything and in cwm (touch recovery 6.0.4.4) it says that it cannot mount anything and errors and partition fails.
Otamoe said:
Hi, could anyone tell me please what i can do with bootlooping S3? It happened on version of CM11 rom, it was workin fine until this one time i plug it to charge it and from then it is just staying on galaxy S3 logo. I can get to download mode and recovery mode but odin wont flash anything and in cwm (touch recovery 6.0.4.4) it says that it cannot mount anything and errors and partition fails.
Click to expand...
Click to collapse
First of all READ. As everybody is saying Ok first question, when You go download mode can you see model name - 9300GT ? If so that means everygthing is solveable.
Next you have messed something and You need to step by step check it. If You want to still work on CM11 you need to flash CF-Root-SGS3-v6.4 to make sure that on the level of recovery everything is ok.
http://forum.xda-developers.com/showpost.php?p=27049380&nocache=1&z=1947389626875519
Than try to flash again Your ROM. We will see where this will bring You.
Thx for reply. So i can see model name in download mode GT-9300 and as you said i try to flash that kernel...
odin said:
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
When I used to be having such problem I was trying to chaoticlly flash everything. Now I can say that this was stupid. Every sytuation is diffrent but some are simmiliar.
Try this topic at least You will be having stock rom with fully func. S3 If it helps you than you will go with Custom ROM otherwise>>> Root and than ROM.
http://forum.xda-developers.com/showthread.php?t=2563562
If this will not solve the problem we will see other oppurtunities.
I cannot flash anything with odin.. when i try so odin stays forever like this:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
Good days to everyone!
I've got a situation with my GT-N7100. It doesn't seem to get past the first logo during boot-up, ever.
I've tried the newest MD5 version for that model. "N7100UBUEND1_N7100TCEEND1_N7100UBUEND1_HOME.tar.m d5"
Used the PIT file to Re-Partition and several versions of Odin.
With the PIT file, only version V3.07 hangs at, "Get PIT for mapping..", all other versions seem to fail.
Pit File used: Q1_20110914_16GB.pit
Without the file I get: (Using the tar.md5 packet with V3.07 Odin)
<ID:0/004> Firmware update start..
<ID:0/004> tz.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
Odin V3.09
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
The phone will not go into recovery mode, the only thing I can get it to do is enter download mode.
How this started? Holding the phone, looking at it. It reset itself and never came back.
I disabled my Anti-Virus... Not sure what else to try. Thank you very much in advance!
***UPDATE*** (I was able to enter recovery mode but it seems to fail to mount anything.)
***UPDATE*** (At wits end, not sure what else to try. I'm thinking the NAND has become corrupt and or unrecoverable. Or unless there was a way to, similar to PC's, do a chkdsk repair. At this time i'm downloading the toolkit and attempt anything through ADB, I feel there is nothing more I could do to Un-Brick the phone. I read about Soft/hard Brick, the phone seems to be Soft Bricked but nothing is allowing me to repair/recover through any download method. Booting into recovery fails to mount everything [as seen in pics].)
Darkie0000 said:
Good days to everyone!
I've got a situation with my GT-N7100. It doesn't seem to get past the first logo during boot-up, ever.
I've tried the newest MD5 version for that model. "N7100UBUEND1_N7100TCEEND1_N7100UBUEND1_HOME.tar.m d5"
Used the PIT file to Re-Partition and several versions of Odin.
With the PIT file, only version V3.07 hangs at, "Get PIT for mapping..", all other versions seem to fail.
Pit File used: Q1_20110914_16GB.pit
Without the file I get: (Using the tar.md5 packet with V3.07 Odin)
<ID:0/004> Firmware update start..
<ID:0/004> tz.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
Odin V3.09
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
The phone will not go into recovery mode, the only thing I can get it to do is enter download mode.
How this started? Holding the phone, looking at it. It reset itself and never came back.
I disabled my Anti-Virus... Not sure what else to try. Thank you very much in advance!
***UPDATE*** (I was able to enter recovery mode but it seems to fail to mount anything.)
***UPDATE*** (At wits end, not sure what else to try. I'm thinking the NAND has become corrupt and or unrecoverable. Or unless there was a way to, similar to PC's, do a chkdsk repair. At this time i'm downloading the toolkit and attempt anything through ADB, I feel there is nothing more I could do to Un-Brick the phone. I read about Soft/hard Brick, the phone seems to be Soft Bricked but nothing is allowing me to repair/recover through any download method. Booting into recovery fails to mount everything [as seen in pics].)
Click to expand...
Click to collapse
I'd try to install a custom recovery and use that to install new software to see if you can get booted. If the custom recovery can't mount anything, then that might tell us more about what's going on.
es0tericcha0s said:
I'd try to install a custom recovery and use that to install new software to see if you can get booted. If the custom recovery can't mount anything, then that might tell us more about what's going on.
Click to expand...
Click to collapse
Thanks for your response! I am not sure where to find a custom recovery or how I would apply that to the phone. Debugging isnt enabled and I cannot enable it as its stuck in boot. Over half of the features wont work in ADB mode, due to debugging not enabled.
Darkie0000 said:
Thanks for your response! I am not sure where to find a custom recovery or how I would apply that to the phone. Debugging isnt enabled and I cannot enable it as its stuck in boot. Over half of the features wont work in ADB mode, due to debugging not enabled.
Click to expand...
Click to collapse
Just have to get to Download Mode and use Odin to install the custom recovery. Has nothing to do with USB Debugging.
http://forum.xda-developers.com/showpost.php?p=55198275&postcount=2
es0tericcha0s said:
Just have to get to Download Mode and use Odin to install the custom recovery. Has nothing to do with USB Debugging.
http://forum.xda-developers.com/showpost.php?p=55198275&postcount=2
Click to expand...
Click to collapse
I'm still not exactly sure where to get this custom ROM you mention.
I tried another recovery, Note2-CWM-6.0.4.3-GT-N7100. It goes about %75 rather quickly and fails.
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Darkie0000 said:
I'm still not exactly sure where to get this custom ROM you mention.
I tried another recovery, Note2-CWM-6.0.4.3-GT-N7100. It goes about %75 rather quickly and fails.
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Sounds like you might have messed it up from flashing that older Pit file, which might have been Gingerbread or early ICS, being that it's from 2011...
You realize that there is a whole sub forum here devoted to your phone, right? It seems like you haven't tried to do much research here.
Hi Devs,
I am stuck in a issue. I installed cm 12.0 (unofficial rom) to my Galaxy s3 GT-i9300 everything was working fine but suddenly it keeps on crashing randomly one day while calling my phone froze. I restarted the phone it stucked on SAMSUNG BOOT SCREEN.
I can go into download mode and recovery mode, currently using PhilzTouch 6 on recovery.
Things I have tried already.
Wiped Cache Partition
Wiped Data/Factory Reset
when i try to wipe cache or factory reset i get errors
E: can't mount /data or Formatting /sdcard/.android_secure
For some reason my phones internal memory is on the read only mode i tried to flash the stock rom as well so far no luck.
I tried 4 different stock roms none of them work they all stopped on nand write or setup connection
I followed the instruction below because thats what exactly happened to my phone but no luck when ever i try to load boot files into PDA it keeps failing.
http://forum.xda-developers.com/showthread.php?t=1840030
please guys i am tired and exhausted trying all different stuff guide me. I even tried PIT Files noting work. Thanks in advance
Try going back to stock/factory.
Boot in download mode (vol down+home+power).
Use Odin to flash stock recovery and firmware.
Once you are able to boot perfectly into touchwiz, can narrow down your points of failure and try again or try another ROM
blu88 said:
Try going back to stock/factory.
Boot in download mode (vol down+home+power).
Use Odin to flash stock recovery and firmware.
Once you are able to boot perfectly into touchwiz, can narrow down your points of failure and try again or try another ROM
Click to expand...
Click to collapse
Hi Blue,
Thanks for reply , so you meant to say i replace philztouch with stock recovery.
Correct me if i am wrong.
Replace philz with stock recovery and replace your rom with touchwiz. Figure out where you went wrong and then flash your custom rom again or flash a different custom rom.
Try flashing another recovery. Worked for me once
Thanks for Help
Can you send me link for GT-i9300 International Stock Recovery so i am installing exact thing it would be great help from you guys and i would really appreciate it.
blu88 said:
Replace philz with stock recovery and replace your rom with touchwiz. Figure out where you went wrong and then flash your custom rom again or flash a different custom rom.
Click to expand...
Click to collapse
Hi Blue i tried official recovery this what comes up and get fails
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
its problem with internal memory to read only is there any way to change it read write mod.
saqygee said:
Hi Blue i tried official recovery this what comes up and get fails
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
its problem with internal memory to read only is there any way to change it read write mod.
Click to expand...
Click to collapse
saqyee, you placed the stock recovery file in the PDA section right? DO NOT TOUCH THE PIT SECTION.
saqygee said:
Hi Blue i tried official recovery this what comes up and get fails
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> recovery.img
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
its problem with internal memory to read only is there any way to change it read write mod.
Click to expand...
Click to collapse
Nand write fail usually means emmc corrupt/damaged you could try the rescue firmware but this looks like hardware failure.
Sent from my LG-D855 using Tapatalk
Hello,
Recently I bought a second hand Samsung Galaxy SIII 9300 with Android 4.3. Because of privacy reasons I’d like to install cm 13.0 on the phone. I already had CM on my former phone, the Nexus 4. This was very easy to install, but I have some difficties with the Samsung Galaxy S3. These are the things I already tried:
I tried to install TWRP 2.8.4 and CWM via Odin 3.1203 in Windows 8. You can see here the log:
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I enabled USB debugging
I unchecked Auto-reboot in Odin.
After I installed TWRP I removed the battery.
Can you help me with my problem?
According to Odin, TWRP succeeded. Can you boot into TWRP? You flashed the correct version of TWRP?
Hello
I cannot boot into TWRP. I am sorry to put it in my question, but that is my question. I tried to flash TWRP 3.0.2.2
Open Odin, only check f reset time, flash, when you see the "reset" in the Odin status window, remove USB cable from phone, remove battery, replace battery, use buttons to get into TWRP.
Root then flash. Flash Chainfire autoroot then flash your recovery, then flash your rom.
Beamed in by telepathy.
I worked!!!! I has to root the phone and than flash TWRL. Thankt you very much!!!
Jan10000 said:
I worked!!!! I has to root the phone and than flash TWRL. Thankt you very much!!!
Click to expand...
Click to collapse
You're welcome. Further advice is to make a backup of your phone once it is set up as you like it. That way, if anything goes tits up you have half of the job already done.
With twrp it's only a matter of time before it (twrp) goes mental and you'll have to resetyour device amd start over. I found the last official clockworkmod recovery the most reliable and have had 2 solid years from it. Also, get a copy of your stock rom from somewhere. You'll need that one day too!.
Beamed in by telepathy.
audit13 said:
Open Odin, only check f reset time, flash, when you see the "reset" in the Odin status window, remove USB cable from phone, remove battery, replace battery, use buttons to get into TWRP.
Click to expand...
Click to collapse
Hi, thanks. This worked for my GT-i9305.
I had previously done the flash for GT-i9300 years ago and was stuck on the same issue as the op.
TWRP 3.3.1-0
twrp-3.3.1-0-i9300.img
twrp-3.3.1-0-i9300.tar
source: https://github.com/ripee/android_device_samsung_i9300